| Internet-Draft | EVN6 | October 2023 |
| Xie & Li | Expires 14 April 2024 | [Page] |
This document describes the mechanism of mapping of Ethernet Virtual Network to IPv6 Underlay for transmission. Unlike the existing methods, this approach places the Ethernet frames to be transmitted directly in the payload of IPv6 packets, i.e., L2 over IPv6, and uses stateless mapping to generate IPv6 source and destination addresses from the host's MAC addresses, Ethernet Virtual Network identifier and site prefixes. The IPv6 packets generated in this way carry Ethernet frames and are routed to the destination site across public IPv6 network.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 14 April 2024.¶
Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
Ethernet Virtual Network is network model of Layer-2 built on top of the underlay to provide connectivity between dispersed customer sites across public network. This overlay L2 virtual network is used to carry the Ethernet data traffic from the individual hosts in an encapsulated format over a logical tunnel, as if they were connected using the same LAN. Ethernet Virtual Network can serve scenarios such as campus networks, enterprise branch interconnections, data center networks, wide area IP bearer networks, and SD-WAN. There have been multiple solutions, they may differ in the types of underlying networks or encapsulation methods, besides, they usually serve different scenarios.¶
VXLAN [RFC7348] is a network virtualization technology which has been used mainly in data centers. VXLAN uses MAC-in-UDP encapsulation for packets, specifically, it encapsulates original Ethernet frames into UDP packets. It then encapsulates the UDP packets with the IP header and Ethernet header of the physical network as outer headers, enabling these packets to be routed across the network like ordinary IP packets.¶
VPLS [RFC4762] make use of MPLS and VPN protocols to provide a virtual LAN between multiple locations. It is basically a way to provide Ethernet-based multi-point to multi-point communication over MPLS networks. VPLS operates by creating a virtual ‘switch’ at the customer’s edge (CE) and the provider’s edge (PE) of their respective networks.¶
The new framework, namely EVN6, proposed in this document aims to efficiently carry Ethernet Virtual Networks in IPv6 networks. It provides a methodology for dynamically creating a tunnel on the IPv6 network to transparently forward Ethernet frame when communication is required between a source and destination node in a Ethernet Virtual Network. In this scheme, Ethernet frame to be transmitted is directly placed in the payload field of IPv6 packet without adding additional payload, the MAC address of the hosts that needs to communicate, the identification of the Ethernet Virtual Network and the IPv6 prefix of the site can be directly mapped to the IPv6 addresses. With EVN6 implementation, any two host can communicate, regardless of the underlying IPv6 network structure and other details. This document specifies EVN6’s overall architecture, typical workflow and Layer-2 broadcast processing, etc.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The following terms are defined and used in this document,¶
EVN6: Multi-site Ethernet Virtual Network built on IPv6 Network¶
E-ADPT: Ethernet Adaptor¶
IID: Interface Identifier(Section 2.5.1 of [RFC4291])¶
VEI: Virtual Ethernet Identification, VEI is used to identify and distinguish different Ethernet Virtual Network instances across the entire network, the length of VEI is 32 bits¶
MAC-VRF: A Virtual Routing and Forwarding table for Media Access Control (MAC) addresses on a PE（Section 3 of [RFC8365]）, it stores IPv6 site prefix, VEI of the Ethernet Virtual Network and other information of each MAC address¶
PE: Provider Edge Router¶
As a common underlay infrastructure, IPv6 network should simultaneously support multiple Ethernet Virtual Networks. To distinguish different Ethernet Virtual Network instances, VEI with a length of 32-bits is used to globally identify them, and it can identify up to 4.29 billion Ethernet Virtual Networks.¶
Generally, Ethernet Virtual Network consists of multiple sites distributed in different geographically locations, and each site is connected to the IPv6 network through local PE at the edge of the IPv6 network. The PE device supports Ethernet Virtual Network services by introducing E-ADPT functional subsystem. E-ADPT directly encapsulates the Ethernet data frames to be transmitted by the customer site into IPv6 packets and sends them to the IPv6 network. For the received IPv6 packets destined to one of this local sites, E-ADPT removes their packet header and restores the original Ethernet frames.¶
--------------- ---------
+---+ Pref6-1 | +----+-----+ | | | Pref6-2 +---+
| H1+---------+--+ E-ADPT | | | +---------+ H2|
+---+ Site1 | +----------+ | | | Site2 +---+
| | | | | |
| | +-------+ | | |
| | |MAC-VRF| | | |
| | +-------+ | | |
|+-------------+| ----------- | |
||IPv6 Network || / \ | |
|| Layer |--|IPv6 network |--| |
|+-------------+| \ / | |
--------------- ----------- ---------
PE1 PE2
Figure 1: EVN6 System Architecture¶
For a given Ethernet Virtual Network, E-ADPT uses the IPv6 site prefix, i.e., Pref6 to identify different sites, so the Pref6 of different sites within a given Ethernet Virtual Network is also different. There are no special requirements for the type of address block used for Pref6, as long as it belongs to the global unicast address type and is reachable in global routing system. The Pref6 for each site can be allocated from the IPv6 address space owned by the operator. It should be noted that the length of Pref6 can be flexibly selected, it can be equal to or less than 64 bits. For Ethernet Virtual Network which has multiple sites, there is a 1: N relationship between the VEI and the site prefix of its sites.¶
In order to send Ethernet frames to the correct destination site through the IPv6 network, MAC-VRF table in PE is used to store the MAC addresses of all hosts in the Ethernet Virtual Network, the corresponding VEI of the Ethernet Virtual Network and Pref6 of the sites they belong to. The format of each record in MAC-VRF is shown in figure 2, it contains MAC address, the VEI value, prefix of the corresponding site.¶
+-----------------------------------------------------------+
| MAC Address | VEI | Length of Pref6 | Pref6 |
+-----------------------------------------------------------+
Pref6:Site Prefix
Figure 2: Data Structure of the Record in MAC-VRF¶
For E-ADPT, MAC-VRF provides a data foundation for encapsulating Ethernet frames into corresponding IPv6 packets, the data in it should be available before sending Ethernet frame to other sites, so the mechanism requires the sites to pre-send host MAC/Pref6 Mapping Advertisement to other sites. After receiving mapping relationship data of a host sent by other PEs, the PE stores the mapping data in the local MAC-VRF. The exchange of MAC/Pref6 can be carried out through the control layer, such as extending EVPN[RFC7432], however, this has been out of the scope of this document and will be discussed in other documents. When receiving Ethernet frame data sent by the host within the site, PE uses the destination MAC address as an index to search for the local MAC-VRF table. If a corresponding entry is found, PE extracts its site prefix Pref6 and VEI value, then uses the process in section 4.2 to encapsulate the Ethernet frame in an IPv6 packet. Afterwards, the IPv6 data packet is transmitted to the IPv6 network.¶
In this section, the Ethernet Virtual Network in figure 3 is used as an example to illustrate the workflow, its profile includes: the VEI value is N1, it has three branch sites connected to PE1, PE2, and PE3, with site prefixes Pref6-1, Pref6-2, and Pref6-3, respectively. Hosts H1, H2, H3 and H4 are located at sites 1, site 2 and site 3, respectively.¶
+-------------------+
| |
| +--+--+ +----+
+---+ +--+--+ | | Site2(Pref6-2) | |
| |Site1(Pref6-1)| | | PE2 +-------------------+ H2 |
| H1+--------------+ PE1 | | | | | Mac2
| | | | +--+--+ +----+
+---+ +--+--+ | +----+
Mac1 | IPv6 | | |
| network | ----+ H3 |
| +--+--+ | | | MAC3
| | |Site3(Pref6-3)| +----+
| | PE3 +--------------|
| | | | +----+
| +--+--+ | | |
| | ----+ H4 |
+-------------------+ | | MAC4
+----+
Figure 3: Diagram of Typical EVN6 Instance¶
The workflow of EVN6 is illustrated as follows:¶
Step 1: EVN6 network creation on each PE device¶
When creating an Ethernet Virtual Network instance on an IPv6 network, it should firstly enable the EVN6 function is in PE1, PE2, and PE3, then configure the relevant information of the Ethernet Virtual Network on this site, configure the Ethernet Virtual Network identifier VEI as N1, and set the site prefix Pref6 on the interface of the PE that the site accesses, indicating that the VEI of the Ethernet Virtual Network to which the site belongs to is N1, and its local site prefix is Pref6. This process can be configured manually or using specific systems such as network management. When the EVN6 instance is running, the sites within it exchange host MAC/Pref6 Mapping through the connected PEs, as described in Section 3.¶
Step 2: Host information search¶
Host H2 in site 2 sends an Ethernet frame with the destination being Host H1 in site 1. Its frame header contains the MAC source address and MAC destination address, which are the MAC addresses of hosts H2 and H1, respectively. In this case, PE2 is the source PE and PE1 is the destination PE. After receiving the Ethernet frame in Site 2, PE2 uses the destination MAC address as an index to search for the local MAC-VRF table. If a corresponding entry is found, the Pref6 of remote site (i.e. Pref6-1) and VEI information are extracted; If not found, do not encapsulate and forward.¶
Step 3: Address mapping and frame encapsulation¶
In EVN6, each Ethernet frame needs to be associated with the VEI of the Ethernet Virtual Network to which the frame originates. Upon receiving the Ethernet frame, PE2 can determine its VEI value based on local configuration. Then the VEI obtained is divided into two sub-segments: VEI-S1 and VEI-S2, the first 16 bits are VEI-S1, and the last 16 bits are VEI-S2. VEI-S1 and VEI-S2 will be respectively put into IPv6 source and destination address of the new IPv6 packet as below.¶
-The IPv6 source address is created by stateless mapping. Specifically, 64-bits Pref6-2 is put into the network prefix field, 16-bits VEI-S1 and source MAC address of the Ethernet frame is put into the field of Interface Identifier, i.e. IID, in order.¶
-The IPv6 destination address is created by stateless mapping too. Specifically, 64-bits Pref6-1 is put into the network prefix field, 16-bits VEI-S2 and destination MAC address of the Ethernet frame is put into the field of Interface Identifier, i.e. IID, in order.¶
The format of IPv6 source and destination addresses generated are shown in figure 4.¶
0 64 80 127
+-------------------+--------+------------+
IPv6 Source Address | Pref6 of | VEI-S1 | Source MAC |
| Source PE | | Address |
+-------------------+--------+------------+
|<---------IID------->|
0 64 80 127
+-------------------+--------+------------+
IPv6 Destination Address | Pref6 of | VEI-S2 | Destination|
| Destination PE | | MAC Address|
+-------------------+--------+------------+
|<--------IID-------->|
Figure 4: Format of IPv6 Source and Destination Addresses¶
Moreover, the Ethernet frame is put into the payload of IPv6 packet and the value of the "Next header" in the header is set to 143, indicating that the payload of the IPv6 packet is an Ethernet frame.¶
+-------------------------------+
| Ethernet Frame |
+-------------------------------+
|
V
+-----------------+-------------------------------+
| IPv6 Header | Palyload(Ethernet Frame) |
+-----------------+-------------------------------+
Figure 5: Encapsulation of Ethernet Frame into IPv6 Packet¶
After the IPv6 packet is generated, it is sent to the IPv6 network via the underlying IPv6 network layer.¶
Step 4: Packet forwarding in IPv6 network¶
When receiving an IPv6 packet, routers in an IPv6 network use the destination address in the packet to look up the routing table and forward it. Since the IPv6 destination address contains the site prefix of the destination site, i.e. Pref6-1 in this case, which provides the egress PE of the packet, routers can forward the IPv6 packet carrying the Ethernet frame to the destination PE, i.e. PE1 in this case. It should be noted that this process does not require additional functionality for non-PE routers in the network, nor does it require extra IPv6 routing information to be added to the IPv6 network.¶
Step 5: Packet de-capsulation and Ethernet frame restoration¶
As shown in figure 6, when receiving a IPv6 packet, the receiving PE, i.e., PE1, checks whether the destination address prefix matches the site prefix Pref6-1 on PE1? If yes, it extracts VEI-s1 and VEI-s2 from the IIDs of the source and destination IPv6 addresses, and concatenates them into VEI, then check if the VEI value is equal to N1? If yes, it then checks if the "Next header" value in the IPv6 header is 143? If yes, it then discards the IPv6 header, takes out the Ethernet frame, and sends the Ethernet frame to H1 within Site 1 based on its destination MAC address. Otherwise, the packet is discarded due to abnormal situation.¶
+--------------------------+
|PE1 receices a IPv6 packet|
+--------------------------+
|
V
+-----+
/Does the \
N /destination\
-------------------+ address +
| \ match /
V \ Pref6-1 /
+------------------------+ +------+
|PE1 continues forwarding| Y|
|forwarding IPv6 packet | V
+------------------------+ +-------------------------+
|PE1 extracts VEI from the|
|IIDs of IPv6 source and |
|destination addresses |
+-------------------------+
|
V
+--+
N / \
---------------------+ VEI=N1?+
| \ /
V +--+
+----------------------------+ Y|
|The packet is discarded due| |
|to abnormal situation | V
+----------------------------+ +-----+
/ The \
N / value of \
-------------------+"Next header"+
| \ is 143? /
V \ /
+----------------------------+ +-----+
|The packet is discarded due | Y|
|to abnormal situation | |
+----------------------------+ V
+------------------------------------------+
|PE1 decapsulates IPv6 packet and sends the|
| released Ethernet frame to H1 based on |
| the destination MAC address |
+------------------------------------------+
Figure 6: Process of Ethernet Frame Restoration in PE¶
Link layer broadcast is used to send data to all hosts in the Layer-2 network where they are located. The destination address of the broadcast frame is FF-FF-FF-FF-FF-FF, and all hosts in the same Layer-2 network will receive the broadcast frame. Link layer broadcast is often used for IPv4 ARP and IPv6 neighbor discovery with ICMPv6 packet of type NS (type 135) [RFC4861][RFC4861]. In Ethernet Virtual Network scenarios, it needs to support link layer broadcast as well.¶
When PE receives a broadcast frame from a local site, it analyzes the VEI of the Ethernet Virtual Network to which the MAC belongs and uses the VEI value as an index to retrieve all other N sites of the Ethernet Virtual Network in MAC-VRF: Site-1, Site-2, …, Site-N. Then, for each remote site, the following operations should be performed recurrently by the source PE,¶
1) Generate new IPv6 packets with the site prefix of the remote site using the method of section 4.2.¶
2) Forward the IPv6 packet to the IPv6 network.¶
Through the above N cycles the broadcast Ethernet frame is encapsulated into IPv6 packets and send the data out, then all other member remote sites will receive the Layer-2 broadcast data.¶
In the EVN6 framework, PE devices located at the edge of the network encapsulate Ethernet frames in IPv6 packets and support transmission between different sites. When generating the outer IPv6 header, the PE device maps information such as the IPv6 address prefix of the site, the Mac address of the host, and the identity of the virtual network to the IPv6 address of the outer encapsulation header, which applies to both the source and destination addresses. In this way, the outer IPv6 address is dynamically generated based on information such as MAC address. For any host to host communication, even if the source and destination hosts are in the same virtual private network, when their source and destination address pairs are different, the generated outer encapsulated IP address is also different. The outer IPv6 address varies with the MAC address of the Ethernet frame, This is different from the traditional encapsulation scheme of pre-configuring tunnel IP addresses, as statically configured tunnel endpoint addresses are likely to become the target of DDOS attacks. In EVN6, tunnel encapsulation adopts dynamically generated tunnel endpoint IPv6 addresses, which avoids the occurrence of DDOS attacks caused by statically pre-configured tunnel addresses. From this perspective, this solution improves the security of Ethernet virtual networks.¶
There are no other special IANA considerations.¶