DetNet Working Group G. Mirsky Internet-Draft ZTE Corp. Intended status: Standards Track M. Chen Expires: May 15, 2019 Huawei November 11, 2018 Operations, Administration and Maintenance (OAM) for Deterministic Networks (DetNet) draft-mirsky-detnet-oam-02 Abstract This document lists functional requirements for Operations, Administration and Maintenance (OAM) toolset in Deterministic Networks (DetNet) and, using these requirements; defines format and use principals of the DetNet service Associated Channel. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on May 15, 2019. Copyright Notice Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of Mirsky & Chen Expires May 15, 2019 [Page 1] Internet-Draft OAM for DetNet November 2018 the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Conventions used in this document . . . . . . . . . . . . . . 3 2.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 2.2. Keywords . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . 4 4. DetNet Data Plane in Support of Active OAM . . . . . . . . . 5 4.1. MPLS Encapsulation . . . . . . . . . . . . . . . . . . . 5 4.1.1. DetNet Active OAM Encapsulation . . . . . . . . . . . 6 4.1.2. IP Encapsulation . . . . . . . . . . . . . . . . . . 8 4.2. DetNet Replication, Elimination, and Ordering Sub- functions Interaction with Active OAM . . . . . . . . . . 8 5. Use of Hybrid OAM in DetNet . . . . . . . . . . . . . . . . . 8 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9 7. Security Considerations . . . . . . . . . . . . . . . . . . . 9 8. Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . 9 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 9 9.1. Normative References . . . . . . . . . . . . . . . . . . 9 9.2. Informational References . . . . . . . . . . . . . . . . 10 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10 1. Introduction [I-D.ietf-detnet-architecture] introduces and explains Deterministic Networks (DetNet) architecture and how the Packet Replication and Elimination function (PREF) can be used to ensure low packet drop ratio in DetNet domain. Operations, Administration and Maintenance (OAM) protocols are used to detect, localize defects in the network, and monitor network performance. Some OAM functions, e.g., failure detection, work in the network proactively, while others, e.g., defect localization, usually performed on-demand. These tasks achieved by a combination of active and hybrid, as defined in [RFC7799], OAM methods. This document lists the functional requirements toward OAM for DetNet domain. The list can further be used for gap analysis of available OAM tools to identify possible enhancements of existing or whether new OAM tools are required to support proactive and on-demand path monitoring and service validation. Mirsky & Chen Expires May 15, 2019 [Page 2] Internet-Draft OAM for DetNet November 2018 2. Conventions used in this document 2.1. Terminology The term "DetNet OAM" used in this document interchangeably with longer version "set of OAM protocols, methods and tools for Deterministic Networks". CW Control Word DetNet Deterministic Networks d-ACH DetNet Associated Channel Header d-CW DetNet Control Word DNH DetNet Header GAL Generic Associated Channel Label G-ACh Generic Associated Channel OAM: Operations, Administration and Maintenance PREF Packet Replication and Elimination Function POF Packet Ordering Function PW Pseudowire RDI Remote Defect Indication Underlay Network or Underlay Layer: The network that provides connectivity between the DetNet nodes. MPLS network providing LSP connectivity between DetNet nodes is an example of the underlay layer. DetNet Node - a node that is an actor in the DetNet domain. DetNet domain edge node and node that performs PREF within the domain are examples of DetNet node. 2.2. Keywords The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Mirsky & Chen Expires May 15, 2019 [Page 3] Internet-Draft OAM for DetNet November 2018 3. Requirements This section lists requirements for OAM in DetNet domain: 1. The listed requirements MUST be supported for any type of underlay network over which a DetNet domain can be realized. 2. It MUST be possible to initiate DetNet OAM session from any DetNet node towards another DetNet node(s) within given domain. 3. It SHOULD be possible to initialize DetNet OAM session from a centralized controller. 4. DetNet OAM MUST support proactive and on-demand OAM monitoring and measurement methods. 5. DetNet OAM packets MUST be in-band, i.e., follow precisely the same path as DetNet data plane traffic both for unidirectional and bi-directional DetNet paths. 6. DetNet OAM MUST support unidirectional OAM methods, continuity check, connectivity verification, and performance measurement. 7. DetNet OAM MUST support bi-directional OAM methods. Such OAM methods MAY combine in-band monitoring or measurement in the forward direction and out-of-bound notification in the reverse direction, i.e., from egress to ingress end point of the OAM test session. 8. DetNet OAM MUST support proactive monitoring of a DetNet node availability in the given DetNet domain. 9. DetNet OAM MUST support Path Maximum Transmission Unit discovery. 10. DetNet OAM MUST support Remote Defect Indication (RDI) notification to the DetNet node performing continuity checking. 11. DetNet OAM MUST support performance measurement methods. 12. DetNet OAM MAY support hybrid performance measurement methods. 13. DetNet OAM MUST support unidirectional performance measurement methods. Calculated performance metrics MUST include but are not limited to throughput, packet loss, delay and delay variation metrics. [RFC6374] provides excellent details on performance measurement and performance metrics. Mirsky & Chen Expires May 15, 2019 [Page 4] Internet-Draft OAM for DetNet November 2018 14. DetNet OAM MUST support defect notification mechanism, like Alarm Indication Signal. Any DetNet node in the given DetNet domain MAY originate a defect notification addressed to any subset of nodes within the domain. 15. DetNet OAM MUST support methods to enable survivability of the DetNet domain. These recovery methods MAY use protection switching and restoration. 16. DetNet OAM MUST support the discovery of Packet Replication, Elimination, and Order preservation sub-functions locations in the domain. 17. DetNet OAM MUST support testing of Packet Replication, Elimination, and Order preservation sub-functions in the domain. 18. DetNet OAM MUST support monitoring any sub-set of paths traversed through the DetNet domain by the DetNet flow. 4. DetNet Data Plane in Support of Active OAM OAM protocols and mechanisms act within the data plane of the particular networking layer. And thus it is critical that the data plane encapsulation supports OAM mechanisms in such a way to comply with the above-listed requirements. One of such examples that require special consideration is requirement #5: DetNet OAM packets MUST be in-band, i.e., follow precisely the same path as DetNet data plane traffic both for unidirectional and bi-directional DetNet paths. 4.1. MPLS Encapsulation The Det Net data plane encapsulation in transport network with MPLS and IP encapsulations specified in [I-D.ietf-detnet-dp-sol-mpls] and [I-D.ietf-detnet-dp-sol-ip] respectively. For the MPLS underlay network, DetNet flows to be encapsulated analogous to pseudowires (PW) over MPLS packet switched network, as described in [RFC3985], [RFC4385]. Generic PW MPLS Control Word (CW), defined in [RFC4385], for DetNet displayed in Figure 1. Mirsky & Chen Expires May 15, 2019 [Page 5] Internet-Draft OAM for DetNet November 2018 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 0 0 0| Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1: DetNet Control Word Format PREF in the DetNet domain composed by a combination of nodes that perform replication and elimination sub-functions. The elimination sub-function always uses the S-Label and packet sequencing information, e.g., the value in the Sequence Number field of DetNet CW (d-CW). The replication sub-function uses the S-Label information only. For data packets Figure 2 presents an example of PREF in DetNet domain. 1111 11111111 111111 112212 112212 132213 CE1----EN1--------R1-------R2-------R3--------EN2----CE2 \2 22222/ 3 / \2222222 /----+ 3 / +------R4------------------------+ 333333333333333333333333 Figure 2: DetNet Data Plane Based on PW 4.1.1. DetNet Active OAM Encapsulation DetNet OAM, like PW OAM, uses PW Associated Channel Header defined in [RFC4385]. Figure 3 displays the encapsulation of a DetNet active OAM packet. Mirsky & Chen Expires May 15, 2019 [Page 6] Internet-Draft OAM for DetNet November 2018 +---------------------------------+ | | | DetNet Flow | | OAM Packet | | | +---------------------------------+ <--\ | DetNet Associated Channel Header| | +=================================+ +--> DetNet OAM data plane | S-Label | | MPLS encapsulation +---------------------------------+ <--/ | T-Label(s) | +---------------------------------+ | Data-Link | +---------------------------------+ | Physical | +---------------------------------+ Figure 3: DetNet active OAM Packet Encapsulation 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 0 0 1|Version|Sequence Number| Channel Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: DetNet Associated Channel Header Format Figure 4 displays the format of the DetNet Associated Channel Header (d-ACH). The meanings of the fields in the d-ACH are: Bits 0..3 MUST be 0b0001. This value of the first nibble allows the packet to be distinguished from an IP packet [RFC4928] and a DetNet data packet [I-D.ietf-detnet-dp-sol-mpls]. Version: this is the version number of the d-ACH. This specification defines version 0. Sequence Number: this is unsigned eight bits-long field. The originating DetNet node MUST set the value of the Sequence Number field to a non-zero before packet being transmitted. The originating node MUST monotonically increase the value of the Sequence Number field for the every next active OAM packet. Channel Type: the value of DetNet Associated Channel Type is one of values defined in the IANA PW Associated Channel Type registry. Mirsky & Chen Expires May 15, 2019 [Page 7] Internet-Draft OAM for DetNet November 2018 The DetNet flow, according to [I-D.ietf-detnet-dp-sol-mpls], is identified by the S-label that MUST be at the bottom of the stack. Active OAM packet MUST have d-ACH immediately following the S-label.A DetNet node originating an OAM packet MUST ensure that the value of the Sequence Number field in d-ACH is monotonically increasing for the given value of the Channel Type field. The Generic Associated Channel Label (GAL), defined in [RFC5586] and [RFC6423], provides a generalized label-based exception mechanism to indicate that the packet is on a Generic Associated Channel (G-ACh) and that ACH immediately follows the label stack. For the DetNet domain in MPLS transport network, GAL MAY be used. If GAL is used, it MUST precede S-Label on the label stack, and the S-Label MUST be followed by d-ACH. 4.1.2. IP Encapsulation [Author's Note: This will be defined based on the DetNet Flow ID specification for IP underlay in [I-D.ietf-detnet-dp-sol-ip].] 4.2. DetNet Replication, Elimination, and Ordering Sub-functions Interaction with Active OAM At the DetNet service layer, special functions MAY be applied to the particular DetNet flow - PREF to potentially lower packet loss, improve the probability of on-time packet delivery and Packet Ordering Function (POF) to ensure in-order packet delivery. As data and the active OAM packets have the same Flow ID, S-label, sub- functions that rely on sequencing information in the DetNet service layer MUST process 28 MSBs of the d-ACH as the source of the sequencing information for the OAM packet. 5. Use of Hybrid OAM in DetNet Hybrid OAM methods are used in performance monitoring and defined in [RFC7799] as: Hybrid Methods are Methods of Measurement that use a combination of Active Methods and Passive Methods. A hybrid measurement method may produce metrics as close to passive, but it still alters something in a data packet even if that is the value of a designated field in the packet encapsulation. One example of such a hybrid measurement method is the Alternate Marking method described in [RFC8321]. Reserving the field for the Alternate Marking method in the DetNet Header will enhance available to an operator set of DetNet OAM tools. Mirsky & Chen Expires May 15, 2019 [Page 8] Internet-Draft OAM for DetNet November 2018 6. IANA Considerations TBA 7. Security Considerations This document lists the OAM requirements for a DetNet domain and does not raise any security concerns or issues in addition to ones common to networking. 8. Acknowledgment Authors extend their appreciation to Pascal Thubert for his insightful comments and productive discussion that helped to improve the document. 9. References 9.1. Normative References [I-D.ietf-detnet-architecture] Finn, N., Thubert, P., Varga, B., and J. Farkas, "Deterministic Networking Architecture", draft-ietf- detnet-architecture-09 (work in progress), October 2018. [I-D.ietf-detnet-dp-sol-ip] Korhonen, J. and B. Varga, "DetNet IP Data Plane Encapsulation", draft-ietf-detnet-dp-sol-ip-01 (work in progress), October 2018. [I-D.ietf-detnet-dp-sol-mpls] Korhonen, J. and B. Varga, "DetNet MPLS Data Plane Encapsulation", draft-ietf-detnet-dp-sol-mpls-01 (work in progress), October 2018. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC5586] Bocci, M., Ed., Vigoureux, M., Ed., and S. Bryant, Ed., "MPLS Generic Associated Channel", RFC 5586, DOI 10.17487/RFC5586, June 2009, . Mirsky & Chen Expires May 15, 2019 [Page 9] Internet-Draft OAM for DetNet November 2018 [RFC6423] Li, H., Martini, L., He, J., and F. Huang, "Using the Generic Associated Channel Label for Pseudowire in the MPLS Transport Profile (MPLS-TP)", RFC 6423, DOI 10.17487/RFC6423, November 2011, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . 9.2. Informational References [RFC3985] Bryant, S., Ed. and P. Pate, Ed., "Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture", RFC 3985, DOI 10.17487/RFC3985, March 2005, . [RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson, "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN", RFC 4385, DOI 10.17487/RFC4385, February 2006, . [RFC4928] Swallow, G., Bryant, S., and L. Andersson, "Avoiding Equal Cost Multipath Treatment in MPLS Networks", BCP 128, RFC 4928, DOI 10.17487/RFC4928, June 2007, . [RFC6374] Frost, D. and S. Bryant, "Packet Loss and Delay Measurement for MPLS Networks", RFC 6374, DOI 10.17487/RFC6374, September 2011, . [RFC7799] Morton, A., "Active and Passive Metrics and Methods (with Hybrid Types In-Between)", RFC 7799, DOI 10.17487/RFC7799, May 2016, . [RFC8321] Fioccola, G., Ed., Capello, A., Cociglio, M., Castaldelli, L., Chen, M., Zheng, L., Mirsky, G., and T. Mizrahi, "Alternate-Marking Method for Passive and Hybrid Performance Monitoring", RFC 8321, DOI 10.17487/RFC8321, January 2018, . Authors' Addresses Greg Mirsky ZTE Corp. Email: gregimirsky@gmail.com Mirsky & Chen Expires May 15, 2019 [Page 10] Internet-Draft OAM for DetNet November 2018 Mach(Guoyi) Chen Huawei Email: mach.chen@huawei.com Mirsky & Chen Expires May 15, 2019 [Page 11]