V6OPS Working Group P. Matthews
Internet-Draft Alcatel-Lucent
Intended status: Informational V. Kuarsingh
Expires: April 21, 2016 Cisco
October 19, 2015

Some Design Choices for IPv6 Networks
draft-ietf-v6ops-design-choices-09

Abstract

This document presents advice on certain routing-related design choices that arise when designing IPv6 networks (both dual-stack and IPv6-only). The intended audience is someone designing an IPv6 network who is knowledgeable about best current practices around IPv4 network design, and wishes to learn the corresponding practices for IPv6.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 21, 2016.

Copyright Notice

Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This document discusses foundational choices that arise when designing a IPv6-only or dual-stack network. The focus is on routing related design choices that are not normally addressed when designing an IPv4-only network. The document presents each topic area along with the most common design choices along with the pros and cons of each choice (or alternative) in detail. Where consensus currently exists around the best practice, this is documented; otherwise the document simply summarizes the current state of the discussion. Thus this document serves to both document the reasoning behind the best current practices for IPv6, and to allow a designer to make an informed choice where no such consensus exists.

The design choices presented apply to both Service Provider and Enterprise network environments. The design areas with the relative choices are not specific to Service Provider or Enterprise networks, but the designer should be aware of their network requirements to best utilize the guidance or choice selection which may differ in each of these general network environments. Where specific choices have selection criteria or analysis requirements which may differ between a Service Provider or Enterprise environment, that will be noted in the text. The designer is encouraged to ensure that they familiarize themselves with any of the discussed technologies to ensure the best selection is made for their environment.

This document does not present advice on strategies for adding IPv6 to a network, nor does it discuss transition in these areas, see [RFC6180] for general advice,[RFC6782] for wireline service providers, [RFC6342]for mobile network providers, [RFC5963] for exchange point operators, [RFC6883] for content providers, and both [RFC4852] and [RFC7381] for enterprises. Nor does this document discuss the particulars of creating an IPv6 addressing plan; for advice in this area, see [RFC5375] or [v6-addressing-plan]. The details of ULA usage is also not discussed; for this the reader is referred to [I-D.ietf-v6ops-ula-usage-recommendations].

Finally, this document focuses on unicast routing design only and does not cover multicast or the issues involved in running MPLS over IPv6 transport.

2. Design Choices

Each subsection below presents a design choice and discusses the pros and cons of the various options. If there is consensus in the industry for a particular option, then the consensus position is noted.

2.1. Addresses

2.1.1. Choice of Addresses in the Core

One of the first choices a network designer needs to make is the type of IPv6 addresses to be used in the network core. IPv6, unlike IPv4, introduces new addressing techniques and concepts, as introduced in [RFC4291] which requires specific attention. The introduction of concepts such as using multiple-addresses per interface or the introduction of linked scoped address-types like Link-Local, mean the designer needs to think beyond the constraints of IPv4. There are also operational considerations as with the concept of a provider assign PA (Provider Aggregatable assigned via upstream provider) versus a Regional Internet Registry assigned PI (Provider Independent assigned from Registry) address type.

At the time of writing, there are still some known operational issues with IPv6 deployments which expose near term deployments to functional or operational gaps that may one day be eliminated. Once such gap is host address selection challenges as noted in [RFC5220] and renumbering challenges as described in [RFC6879] and [RFC7010].

Within this document, Unique Local Addresses (ULA) [RFC4193] are likened to [RFC1918] addresses from an operational perspective. Although ULAs are not architecturally similar to [RFC1918] private addresses, the reasons for selecting them, and the challenge that may arise if they are the only address type available to achieve external network connectivity are similar. “Private” in this document refers to the nature that ULAs would be typically used for internal communications only, or externally with assistance from technologies like NAT, given the addresses are not routed directly with external networks.

A related choice is whether to use only link-local addresses on certain links. That choice is discussed later in the document; this section is about those addresses that must be visible throughout the network.

The following table lists the main options available.

GRT Address Type End-User Traffic ISP Enterprise
PI Hop-by-hop Works Works
PI Tunneled Works. Using private space likely a better option. Works. Using private space likely a better option.
PA Hop-by-hop Works Works
PA Tunneled Works. Using private addresses likely better option. Works. Using private addresses likely better option.
Private Hop-by-hop Will likely cause problems. See discussion below. Works. Careful consideration due to NAT implications.
Private Tunneled Works Works

As the table indicates, there are three options for the type of addresses a network designer can use in the network core:

In all cases, we are talking about the type of addresses used in the GRT context (Global Routing Table aka base router). If end-user traffic is routed hop-by-hop through the network based on the destination address in the IP header, then this context is visible to the end-user. However, if all end-user traffic is tunneled through the core (for example, using MPLS) then this context is not visible to the end-user.

First, consider the case where at least some end-user traffic is routed hop-by-hop. In this case, the use of PI space is the best option, as it gives the most flexibility in the future. However, some organizations may be unable or unwilling to obtain PI space - in this case PA space is the next-best choice. For an ISP, the use of private address space is problematic - see [RFC6752] for a discussion. For an enterprise, the use of private address space is an option and may be seen as favourable operationally, but should only be used after careful consideration of the technological drawbacks. If ULAs are the only non-Link-Local address available the hosts, the enterprise will need to use translation technologies such as NPT[RFC6296] or NAT66 to reach the Internet. If the network has no connection to the Internet, or the hosts only assigned a ULA do not need external connectivity, then this limitation is not a problem.

Now consider the case where all end-user traffic is tunneled through the core and thus the core is not visible to other networks. In this case, the use of private addresses in the core is the most reasonable and re-enforces the desire that these addresses have limited visibility. The use of PI space is the next-best option - two reasons for selecting this option is to provide flexibility in case some traffic needs to be carried hop-by-hop in the future and to be absolutely sure that there are no address conflicts. Getting IPv4 PI space at this time will be difficult, but IPv6 PI space is fairly easy.

The use of PA space is likely a poor option for many organizations since these networks are connected to more then one upstream provider and/or may need flexibility on how Internet reachability needs to be managed. Using PA space subjects the end network to possible reclamation of address space in the future, which requires a renumbering activity.

Not shown in the table above are combinations of the basic options. An example of a combination is using both PA and ULA address space in the hop-by-hop enterprise case or multiple PA and/or PI addresses. Combinations can reduce the magnitude of the deficiency with a basic option, but does not eliminate it completely. For example, using PA + ULA for the hop-by-hop enterprise case reduces the amount of renumbering required when changing providers compared with the pure PA case, but does not eliminate it completely. Additional work analyzing the opportunities for using multiple addresses and overcoming limitations can be found in [I-D.ietf-v6ops-host-addr-availability].

2.2. Interfaces

2.2.1. Mix IPv4 and IPv6 on the Same Layer-3 Interface?

If a network is going to carry both IPv4 and IPv6 traffic, as many networks do today, then a fundamental question arises: Should an operator mix IPv4 and IPv6 traffic or keep them separated? More specifically, should the design:

  1. Mix IPv4 and IPv6 traffic on the same layer-3 interface, OR
  2. Separate IPv4 and IPv6 by using separate interfaces (e.g., two physical links or two VLANs on the same link)?

Option (a) implies a single layer-3 interface at each end of the connection with both IPv4 and IPv6 addresses; while option (b) implies two layer-3 interfaces at each end, one for IPv4 addresses and one with IPv6 addresses.

The advantages of option (a) include:

For these reasons, there is a relatively strong consensus in the operator community that option (a) is the preferred way to go. Most networks today use option (a) wherever possible.

However, there can be times when option (b) is the pragmatic choice. Most commonly, option (b) is used to work around limitations in network equipment. One big example is the generally poor level of support today for individual statistics on IPv4 traffic vs IPv6 traffic when option (a) is used. Other, device-specific, limitations exist as well. It is expected that these limitations will go away as support for IPv6 matures, making option (b) less and less attractive until the day that IPv4 is finally turned off.

2.2.2. Interfaces with Only Link-Local Addresses?

As noted in the introduction, this document does not cover the ins and outs around creating an IPv6 addressing plan. However, there is one fundamental question in this area that often arises: Should an interface:

  1. Use only a link-local address (“link-local-only”), OR
  2. Have global and/or unique-local addresses assigned in addition to the link-local?

There are two advantages in interfaces with only link-local addresses ("link-local-only interfaces"). The first advantage is ease of configuration. In a network with a large number of link-local-only interfaces, the operator can just enable an IGP on each router, without going through the tedious process of assigning and tracking the addresses for each interface. The second advantage is security. Since packets with Link-Local destination addresses should not be routed, it is very difficult to attack the associated nodes from an off-link device. This implies less effort around maintaining security ACLs.

Countering this advantage are various disadvantages to link-local-only interfaces:

It should be noted that it is quite possible for the same link-local address to be assigned to multiple interfaces. This can happen because the MAC address is duplicated (due to manufacturing process defaults or the use of virtualization), because a device deliberately re-uses automatically-assigned link-local addresses on different links, or because an operator manually assigns the same easy-to-type link-local address to multiple interfaces. All these are allowed in IPv6 as long as the addresses are used on different links.

For more discussion on the pros and cons, see [RFC7404]. See also [RFC5375] for IPv6 unicast address assignment considerations.

Today, most operators use interfaces with global or unique-local addresses (option b).

2.3. Static Routes

2.3.1. Link-Local Next-Hop in a Static Route?

For the most part, the use of static routes in IPv6 parallels their use in IPv4. There is, however, one exception, which revolves around the choice of next-hop address in the static route. Specifically, should an operator:

  1. Use the far-end’s link-local address as the next-hop address, OR
  2. Use the far-end’s GUA/ULA address as the next-hop address?

Recall that the IPv6 specs for OSPF [RFC5340] and ISIS [RFC5308] dictate that they always use link-locals for next-hop addresses. For static routes, [RFC4861] section 8 says:

This implies that using a GUA or ULA as the next hop will prevent a router from sending Redirect messages for packets that "hit" this static route. All this argues for using a link-local as the next-hop address in a static route.

However, there are two cases where using a link-local address as the next-hop clearly does not work. One is when the static route is an indirect (or multi-hop) static route. The second is when the static route is redistributed into another routing protocol. In these cases, the above text from RFC 4861 notwithstanding, either a GUA or ULA must be used.

Furthermore, many network operators are concerned about the dependency of the default link-local address on an underlying MAC address, as described in the previous section.

Today most operators use GUAs as next-hop addresses.

2.4. IGPs

2.4.1. IGP Choice

One of the main decisions for a network operator looking to deploy IPv6 is the choice of IGP (Interior Gateway Protocol) within the network. The main options are OSPF, IS-IS and EIGRP. RIPng is another option, but very few networks run RIP in the core these days, so it is covered in a separate section below.

OSPF [RFC2328] [RFC5340] and IS-IS [RFC5120][RFC5120] are both standardized and link-state protocols. Standardized means they are widely supported by vendors, while link-state means amongst other things that they can support RSVP-TE, which is widely used for MPLS signaling. Both of these protocols are widely deployed. By contrast, EIGRP [ref] is a proprietary distance-vector protocol. EIGRP is rarely deployed in service-provider networks, but is quite common in enterprise networks.

The table below sets out possible combinations of protocols to route both IPv4 and IPv6, and makes some observations on each combination.

IGP for IPv4 IGP for IPv6 Multiple Known Deployments Protocol separation Similar configuration possible
OSPFv2 OSPFv3 YES (8) YES YES
OSPFv2 IS-IS YES (3) YES -
OSPFv2 EIGRP - YES -
OSPFv3 IS-IS - YES -
OSPFv3 EIGRP - YES -
IS-IS OSPFv3 YES (2) YES -
IS-IS IS-IS YES (12) - YES
IS-IS EIGRP - YES -
EIGRP OSPFv3 ? (1) YES -
EIGRP IS-IS - YES -
EIGRP EIGRP ? (2) - YES

In the column "Multiple Known Deployments", a YES indicates that a significant number of production networks run this combination, with the number of such networks indicated in parentheses following, while a "?" indicates that the authors are only aware of one or two small networks that run this combination. Data for this column was gathered from an informal poll of operators on a number of mailing lists. This poll was not intended to be a thorough scientific study of IGP choices, but to provide a snapshot of known operator choices at the time of writing (Mid-2015) for successful production dual stack network deployments. There were twenty six (26) network implementations represented by 17 respondents. Some respondents provided information on more then one network or network deployment. Due to privacy considerations, the networks' represented and respondents are not listed in this document.

A number of combinations are marked as offering “Protocol separation”. These options use a different IGP protocol for IPv4 vs IPv6. With these options, a problem with routing IPv6 is unlikely to affect IPv4 or visa-versa. Some operator may consider this as a benefit when first introducing dual stack capabilities or for ongoing technical reasons.

Three combinations are marked “Similar configuration possible”. This means it is possible (but not required) to use very similar IGP configuration for IPv4 and IPv6: for example, the same area boundaries, area numbering, link costing, etc. If you are happy with your IPv4 IGP design, then this will likely be a consideration. By contrast, the options that use, for example, IS-IS for one IP version and OSPF for the other version will require considerably different configuration, and will also require the operations staff to become familiar with the difference between the two protocols.

It should be noted that a number of ISPs have run OSPF as their IPv4 IGP for quite a few years, but have selected IS-IS as their IPv6 IGP. However, there are very few (none?) that have made the reverse choice. This is, in part, because routers generally support more nodes in an IS-IS area than in the corresponding OSPF area, and because IS-IS is seen as more secure because it runs at layer 2.

2.4.2. IS-IS Topology Mode

When IS-IS is used to route both IPv4 and IPv6, then there is an additional choice of whether to run IS-IS in single-topology or multi-topology mode. Single-topology mode allows IPv4 and IPv6 to share a single topology and a single set of link costs[RFC5308]. Multi-topology mode allows separate IPv4 and IPv6 topologies with potentially different link costs.

In the informal poll of operators, out of 12 production networks that ran IS-IS for both IPv4 and IPv6, 6 used Single Topology mode, 4 used Multi-Topology mode, and 2 did not specify. One motivation often cited by then operators for using Single Topology mode was because some device did not support multi-topology mode.

Traditional thinking has been that multi-topology mode offers the most flexibility. Never-the-less, as shown by the poll results, a number of operators have used single-topology mode successfully.

2.4.3. RIP

A protocol option not described in the table above is RIPng [RFC2080]. RIPng is a distance vector protocol with limitations in larger networks. However there is prevalent use case in large operator networks where RIP is used for edge facing core interfaces to manage high count aggregation of dynamic routing endpoints. Although not a mainline option for the network core as a whole, it is commonly used in IPv4, and potentially in IPv6 for a common set of links/functions.

2.5. BGP

2.5.1. Which Transport for Which Routes?

BGP these days is multi-protocol. It can carry routes from many different families, and it can do this when the BGP session, or more accurately the underlying TCP connection, runs over either IPv4 or IPv6 (here referred to as either "IPv4 transport" or "IPv6 transport"). Given this flexibility, one of the biggest questions when deploying BGP in a dual-stack network is the question of which routes should be carried over sessions using IPv4 transport and which should be carried over sessions using IPv6 transport.

To answer this question, consider the following table:

Route Family Transport Comments
Unlabeled IPv4 IPv4 Works well
Unlabeled IPv4 IPv6 Next-hop issues
Unlabeled IPv6 IPv4 Next-hop issues
Unlabeled IPv6 IPv6 Works well
Labeled IPv4 IPv4 Works well
Labeled IPv4 IPv6 Next-hop issues
Labeled IPv6 IPv4 (6PE) Works well
Labeled IPv6 IPv6 Needs MPLS over IPv6
VPN IPv4 IPv4 Works well
VPN IPv4 IPv6 Next-hop issues
VPN IPv6 IPv4 (6VPE) Works well
VPN IPv6 IPv6 Needs MPLS over IPv6

The first column in this table lists various route families, where “unlabeled” means SAFI 1, “labeled” means the routes carry an MPLS label (SAFI 4, see [RFC3107]), and “VPN” means the routes are normally associated with a layer-3 VPN (SAFI 128, see [RFC4364] ). The second column lists the protocol used to transport the BGP session, frequently specified by giving either an IPv4 or IPv6 address in the “neighbor” statement.

The third column comments on the combination in the first two columns:

Also, it is important to note that changing the set of address families being carried over a BGP session requires the BGP session to be reset (unless something like [I-D.ietf-idr-dynamic-cap] or [I-D.ietf-idr-bgp-multisession] is in use). This is generally more of an issue with eBGP sessions than iBGP sessions: for iBGP sessions it is common practice for a router to have two iBGP sessions, one to each member of a route reflector pair, so one can change the set of address families on first one of the sessions and then the other.

The following subsections discuss specific scenarios in more detail.

2.5.1.1. BGP Sessions for Unlabeled Routes

Unlabeled routes are commonly carried on eBGP sessions, as well as on iBGP sessions in networks where Internet traffic is carried unlabeled across the network. In these scenarios, operators today most commonly use two BGP sessions: one session is transported over IPv4 and carries the unlabeled IPv4 routes, while the second session is transported over IPv6 and carries the unlabeled IPv6 routes.

There are several reasons for this choice:

2.5.1.2. BGP sessions for Labeled or VPN Routes

In these scenarios, it is most common today to carry both the IPv4 and IPv6 routes over sessions transported over IPv4. This can be done with either: (a) one session carrying both route families, or (b) two sessions, one for each family.

Using a single session is usually appropriate for an iBGP session going to a route reflector handling both route families. Using a single session here usually means that the BGP session will reset when changing the set of address families, but as noted above, this is usually not a problem when redundant route reflectors are involved.

In eBGP situations, two sessions are usually more appropriate.

2.5.2. eBGP Endpoints: Global or Link-Local Addresses?

When running eBGP over IPv6, there are two options for the addresses to use at each end of the eBGP session (or more properly, the underlying TCP session):

  1. Use link-local addresses for the eBGP session, OR
  2. Use global addresses for the eBGP session.

Note that the choice here is the addresses to use for the eBGP sessions, and not whether the link itself has global (or unique-local) addresses. In particular, it is quite possible for the eBGP session to use link-local addresses even when the link has global addresses.

The big attraction for option (a) is security: an eBGP session using link-local addresses is extremely difficult to attack from a device that is off-link. This provides very strong protection against TCP RST and similar attacks. Though there are other ways to get an equivalent level of security (e.g. GTSM [RFC5082], MD5 [RFC5925], or ACLs), these other ways require additional configuration which can be forgotten or potentially mis-configured.

However, there are a number of small disadvantages to using link-local addresses:

For these reasons, most operators today choose to have their eBGP sessions use global addresses.

3. General Observations

There are two themes that run though many of the design choices in this document. This section presents some general discussion on these two themes.

3.1. Use of Link-Local Addresses

The proper use of link-local addresses is a common theme in the IPv6 network design choices. Link-layer addresses are, of course, always present in an IPv6 network, but current network design practice mostly ignores them, despite efforts such as [RFC7404].

There are three main reasons for this current practice:

3.2. Separation of IPv4 and IPv6

Currently, most operators are running or planning to run networks that carry both IPv4 and IPv6 traffic. Hence the question: To what degree should IPv4 and IPv6 be kept separate? As can be seen above, this breaks into two sub-questions: To what degree should IPv4 and IPv6 traffic be kept separate, and to what degree should IPv4 and IPv6 routing information be kept separate?

The general consensus around the first question is that IPv4 and IPv6 traffic should generally be mixed together. This recommendation is driven by the operational simplicity of mixing the traffic, plus the general observation that the service being offered to the end user is Internet connectivity and most users do not know or care about the differences between IPv4 and IPv6. Thus it is very desirable to mix IPv4 and IPv6 on the same link to the end user. On other links, separation is possible but more operationally complex, though it does occasionally allow the operator to work around limitations on network devices. The situation here is roughly comparable to IP and MPLS traffic: many networks mix the two traffic types on the same links without issues.

By contrast, there is more of an argument for carrying IPv6 routing information over IPv6 transport, while leaving IPv4 routing information on IPv4 transport. By doing this, one gets fate-sharing between the control and data plane for each IP protocol version: if the data plane fails for some reason, then often the control plane will too.

4. IANA Considerations

This document makes no requests of IANA.

5. Security Considerations

This document introduces no new security considerations that are not already documented elsewhere.

The following is a brief list of pointers to documents related to the topics covered above that the reader may wish to review for security considerations.

For general IPv6 security, [RFC4942] provides guidance on security considerations around IPv6 transition and coexistence.

For OSPFv3, the base protocol specification [RFC5340] has a short security considerations section which notes that the fundamental mechanism for protecting OSPFv3 from attacks is the mechanism described in [RFC4552].

For IS-IS, [RFC5308] notes that ISIS for IPv6 raises no new security considerations over ISIS for IPv4 over those documented in [ISO10589] and [RFC5304].

For BGP, [RFC2545] notes that BGP for IPv6 raises no new security considerations over those present in BGP for IPv4. However, there has been much discussion of BGP security recently, and the interested reader is referred to the documents of the IETF's SIDR working group.

6. Acknowledgements

Many, many people in the V6OPS working group provided comments and suggestions that made their way into this document. A partial list includes: Rajiv Asati, Fred Baker, Michael Behringer, Marc Blanchet, Ron Bonica, Randy Bush, Cameron Byrne, Brian Carpenter, KK Chittimaneni, Tim Chown, Lorenzo Colitti, Gert Doering, Francis Dupont, Bill Fenner, Kedar K Gaonkar, Chris Grundemann, Steinar Haug, Ray Hunter, Joel Jaeggli, Victor Kuarsingh, Jen Linkova, Ivan Pepelnjak, Alexandru Petrescu, Rob Shakir, Mark Smith, Jean-Francois Tremblay, Dave Thaler, Tina Tsou, Eric Vyncke, Dan York, and Xuxiaohu.

The authors would also like to thank Pradeep Jain and Alastair Johnson for helpful comments on a very preliminary version of this document.

7. Informative References

[I-D.ietf-idr-bgp-multisession] Scudder, J., Appanna, C. and I. Varlashkin, "Multisession BGP", Internet-Draft draft-ietf-idr-bgp-multisession-07, September 2012.
[I-D.ietf-idr-dynamic-cap] Ramachandra, S. and E. Chen, "Dynamic Capability for BGP-4", Internet-Draft draft-ietf-idr-dynamic-cap-14, December 2011.
[I-D.ietf-v6ops-host-addr-availability] Colitti, L., Cerf, V., Cheshire, S. and D. Schinazi, "Host address availability recommendations", Internet-Draft draft-ietf-v6ops-host-addr-availability-01, September 2015.
[I-D.ietf-v6ops-ula-usage-recommendations] Liu, B. and S. Jiang, "Considerations For Using Unique Local Addresses", Internet-Draft draft-ietf-v6ops-ula-usage-recommendations-05, May 2015.
[ISO10589] International Standards Organization, "Intermediate system to Intermediate system intra-domain routeing information exchange protocol for use in conjunction with the protocol for providing the connectionless-mode Network Service (ISO 8473)", International Standard 10589:2002, Nov 2002.
[RFC1918] Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G. and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, DOI 10.17487/RFC1918, February 1996.
[RFC2080] Malkin, G. and R. Minnear, "RIPng for IPv6", RFC 2080, DOI 10.17487/RFC2080, January 1997.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, DOI 10.17487/RFC2328, April 1998.
[RFC2545] Marques, P. and F. Dupont, "Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing", RFC 2545, DOI 10.17487/RFC2545, March 1999.
[RFC3107] Rekhter, Y. and E. Rosen, "Carrying Label Information in BGP-4", RFC 3107, DOI 10.17487/RFC3107, May 2001.
[RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast Addresses", RFC 4193, DOI 10.17487/RFC4193, October 2005.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006.
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February 2006.
[RFC4472] Durand, A., Ihren, J. and P. Savola, "Operational Considerations and Issues with IPv6 DNS", RFC 4472, DOI 10.17487/RFC4472, April 2006.
[RFC4552] Gupta, M. and N. Melam, "Authentication/Confidentiality for OSPFv3", RFC 4552, DOI 10.17487/RFC4552, June 2006.
[RFC4852] Bound, J., Pouffary, Y., Klynsma, S., Chown, T. and D. Green, "IPv6 Enterprise Network Analysis - IP Layer 3 Focus", RFC 4852, DOI 10.17487/RFC4852, April 2007.
[RFC4861] Narten, T., Nordmark, E., Simpson, W. and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, DOI 10.17487/RFC4861, September 2007.
[RFC4942] Davies, E., Krishnan, S. and P. Savola, "IPv6 Transition/Co-existence Security Considerations", RFC 4942, DOI 10.17487/RFC4942, September 2007.
[RFC5082] Gill, V., Heasley, J., Meyer, D., Savola, P. and C. Pignataro, "The Generalized TTL Security Mechanism (GTSM)", RFC 5082, DOI 10.17487/RFC5082, October 2007.
[RFC5120] Przygienda, T., Shen, N. and N. Sheth, "M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs)", RFC 5120, DOI 10.17487/RFC5120, February 2008.
[RFC5220] Matsumoto, A., Fujisaki, T., Hiromi, R. and K. Kanayama, "Problem Statement for Default Address Selection in Multi-Prefix Environments: Operational Issues of RFC 3484 Default Rules", RFC 5220, DOI 10.17487/RFC5220, July 2008.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic Authentication", RFC 5304, DOI 10.17487/RFC5304, October 2008.
[RFC5308] Hopps, C., "Routing IPv6 with IS-IS", RFC 5308, DOI 10.17487/RFC5308, October 2008.
[RFC5340] Coltun, R., Ferguson, D., Moy, J. and A. Lindem, "OSPF for IPv6", RFC 5340, DOI 10.17487/RFC5340, July 2008.
[RFC5375] Van de Velde, G., Popoviciu, C., Chown, T., Bonness, O. and C. Hahn, "IPv6 Unicast Address Assignment Considerations", RFC 5375, DOI 10.17487/RFC5375, December 2008.
[RFC5838] Lindem, A., Mirtorabi, S., Roy, A., Barnes, M. and R. Aggarwal, "Support of Address Families in OSPFv3", RFC 5838, DOI 10.17487/RFC5838, April 2010.
[RFC5925] Touch, J., Mankin, A. and R. Bonica, "The TCP Authentication Option", RFC 5925, DOI 10.17487/RFC5925, June 2010.
[RFC5963] Gagliano, R., "IPv6 Deployment in Internet Exchange Points (IXPs)", RFC 5963, DOI 10.17487/RFC5963, August 2010.
[RFC6180] Arkko, J. and F. Baker, "Guidelines for Using IPv6 Transition Mechanisms during IPv6 Deployment", RFC 6180, DOI 10.17487/RFC6180, May 2011.
[RFC6296] Wasserman, M. and F. Baker, "IPv6-to-IPv6 Network Prefix Translation", RFC 6296, DOI 10.17487/RFC6296, June 2011.
[RFC6342] Koodli, R., "Mobile Networks Considerations for IPv6 Deployment", RFC 6342, DOI 10.17487/RFC6342, August 2011.
[RFC6752] Kirkham, A., "Issues with Private IP Addressing in the Internet", RFC 6752, DOI 10.17487/RFC6752, September 2012.
[RFC6782] Kuarsingh, V. and L. Howard, "Wireline Incremental IPv6", RFC 6782, DOI 10.17487/RFC6782, November 2012.
[RFC6879] Jiang, S., Liu, B. and B. Carpenter, "IPv6 Enterprise Network Renumbering Scenarios, Considerations, and Methods", RFC 6879, DOI 10.17487/RFC6879, February 2013.
[RFC6883] Carpenter, B. and S. Jiang, "IPv6 Guidance for Internet Content Providers and Application Service Providers", RFC 6883, DOI 10.17487/RFC6883, March 2013.
[RFC7010] Liu, B., Jiang, S., Carpenter, B., Venaas, S. and W. George, "IPv6 Site Renumbering Gap Analysis", RFC 7010, DOI 10.17487/RFC7010, September 2013.
[RFC7217] Gont, F., "A Method for Generating Semantically Opaque Interface Identifiers with IPv6 Stateless Address Autoconfiguration (SLAAC)", RFC 7217, DOI 10.17487/RFC7217, April 2014.
[RFC7381] Chittimaneni, K., Chown, T., Howard, L., Kuarsingh, V., Pouffary, Y. and E. Vyncke, "Enterprise IPv6 Deployment Guidelines", RFC 7381, DOI 10.17487/RFC7381, October 2014.
[RFC7404] Behringer, M. and E. Vyncke, "Using Only Link-Local Addressing inside an IPv6 Network", RFC 7404, DOI 10.17487/RFC7404, November 2014.
[v6-addressing-plan] SurfNet, "Preparing an IPv6 Address Plan", 2013.

Authors' Addresses

Philip Matthews Alcatel-Lucent 600 March Road Ottawa, Ontario K2K 2E6 Canada Phone: +1 613-784-3139 EMail: philip_matthews@magma.ca
Victor Kuarsingh Cisco 88 Queens Quay Toronto, ON M5J0B8 Canada EMail: victor@jvknet.com