TSVWG J. Touch Internet Draft Independent Consultant Intended status: Standards Track March 1, 2022 Intended updates: 768 Expires: September 2022 Transport Options for UDP draft-ietf-tsvwg-udp-options-14.txt Abstract Transport protocols are extended through the use of transport header options. This document extends UDP by indicating the location, syntax, and semantics for UDP transport layer options. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at https://www.ietf.org/shadow.html Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on September 1, 2022. Copyright Notice Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of Touch Expires September 1, 2022 [Page 1] Internet-Draft Transport Options for UDP March 2022 publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction.................................................. 3 2. Conventions used in this document............................. 3 3. Background.................................................... 3 4. The UDP Option Area........................................... 4 5. The UDP Option Area Structure................................. 7 6. The Option Checksum (OCS)..................................... 7 7. UDP Options................................................... 9 8. Safe UDP Options............................................. 12 8.1. End of Options List (EOL)............................... 12 8.2. No Operation (NOP)...................................... 13 8.3. Alternate Payload Checksum (APS)........................ 13 8.4. Fragmentation (FRAG).................................... 14 8.5. Maximum Segment Size (MSS).............................. 18 8.6. Maximum Reassembled Segment Size (MRSS)................. 19 8.7. Echo request (REQ) and echo response (RES).............. 19 9. Unsafe (UNSAFE) Options...................................... 23 9.1. Timestamps (TIME)....................................... 20 9.2. Authentication (AUTH)................................... 21 9.3. Experimental (EXP)...................................... 22 10. Rules for designing new options............................. 24 11. Option inclusion and processing............................. 25 12. UDP API Extensions.......................................... 26 13. UDP Options are for Transport, Not Transit.................. 27 14. UDP options vs. UDP-Lite.................................... 27 15. Interactions with Legacy Devices............................ 28 16. Options in a Stateless, Unreliable Transport Protocol....... 29 17. UDP Option State Caching.................................... 29 18. Updates to RFC 768.......................................... 30 19. Interactions with other RFCs (and drafts)................... 30 20. Multicast Considerations.................................... 31 21. Security Considerations..................................... 31 22. IANA Considerations......................................... 33 23. References.................................................. 33 23.1. Normative References................................... 33 23.2. Informative References................................. 34 24. Acknowledgments............................................. 36 Appendix A. Implementation Information.......................... 37 Touch Expires September 1, 2022 [Page 2] Internet-Draft Transport Options for UDP March 2022 1. Introduction Transport protocols use options as a way to extend their capabilities. TCP [RFC793], SCTP [RFC4960], and DCCP [RFC4340] include space for these options but UDP [RFC768] currently does not. This document defines an extension to UDP that provides space for transport options including their generic syntax and semantics for their use in UDP's stateless, unreliable message protocol. 2. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. In this document, the characters ">>" preceding an indented line(s) indicates a statement using the key words listed above. This convention aids reviewers in quickly identifying or finding the portions of this RFC covered by these key words. 3. Background Many protocols include a default, invariant header and an area for header options that varies from packet to packet. These options enable the protocol to be extended for use in particular environments or in ways unforeseen by the original designers. Examples include TCP's Maximum Segment Size, Window Scale, Timestamp, and Authentication Options [RFC793][RFC5925][RFC7323]. Header options are used both in stateful (connection-oriented, e.g., TCP [RFC793], SCTP [RFC4960], DCCP [RFC4340]) and stateless (connectionless, e.g., IPv4 [RFC791], IPv6 [RFC8200]) protocols. In stateful protocols they can help extend the way in which state is managed. In stateless protocols their effect is often limited to individual packets, but they can have an aggregate effect on a sequence of packets as well. UDP is one of the most popular protocols that lacks space for header options [RFC768]. The UDP header was intended to be a minimal addition to IP, providing only ports and a checksum for error detection. This document extends UDP to provide a trailer area for such options, located after the UDP data payload. Touch Expires September 1, 2022 [Page 3] Internet-Draft Transport Options for UDP March 2022 UDP options are possible because UDP includes its own length field, separate from that of the IP header. Other transport protocols infer transport payload length from the IP datagram length (TCP, DCCP, SCTP). There are a number of reasons why Internet historians suggest that UDP includes this field, e.g., to support multiple UDP segments in the same IP packet or to indicate the length of the UDP payload as distinct from zero padding required for systems that require writes that are not byte-aligned. These suggestions are not consistent with earlier versions of UDP or with concurrent design of multi-segment multiplexing protocols, however, so the real reason remains unknown. Regardless, this field presents an opportunity to differentiate a UDP payload from the implied transport payload length, which this document leverages to support a trailer options field. There are other ways to include additional header fields or options in protocols that otherwise are not extensible. In particular, in- band encoding can be used to differentiate transport payload from additional fields, such as was proposed in [Hi15]. This approach can cause complications for interactions with legacy devices, and is thus not considered further in this document. IPv6 Teredo [RFC6081] uses values of the UDP Length that are larger than the IP transport payload as an additional type of signal, as noted in Section 19. UTP options uses a value smaller than the IP transport payload to enable backwards compatibility with existing UDP implementations, i.e., to deliver the UDP Length of user data to the application and silently ignore the additional surplus area data. Using a value larger than the IP transport payload could either be considered malformed (and be silently dropped) or could cause buffer overruns, and so is not considered silently and safely backward compatible. 4. The UDP Option Area The UDP transport header includes demultiplexing and service identification (port numbers), an error detection checksum, and a field that indicates the UDP datagram length (including UDP header). The UDP Length field is typically redundant with the size of the maximum space available as a transport protocol payload, as determined by the IP header (see detail in Section 15). The UDP Option area is created when the UDP Length indicates a smaller transport payload than implied by the IP header. For IPv4, IP Total Length field indicates the total IP datagram length (including IP header) and the size of the IP options is indicated in the IP header (in 4-byte words) as the "Internet Header Touch Expires September 1, 2022 [Page 4] Internet-Draft Transport Options for UDP March 2022 Length" (IHL), as shown in Figure 1 [RFC791]. As a result, the typical (and largest valid) value for UDP Length is: UDP_Length = IPv4_Total_Length - IPv4_IHL * 4 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Version| IHL |Type of Service| Total Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification |Flags| Fragment Offset | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Time to Live | Proto=17 (UDP)| Header Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... zero or more IP Options (using space as indicated by IHL) ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Source Port | UDP Destination Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Length | UDP Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IPv4 datagram with UDP transport payload For IPv6, the IP Payload Length field indicates the datagram after the base IPv6 header, which includes the IPv6 extension headers and space available for the transport protocol, as shown in Figure 2 [RFC8200]. Note that the Next HDR field in IPv6 might not indicate UDP (i.e., 17), e.g., when intervening IP extension headers are present. For IPv6, the lengths of any additional IP extensions are indicated within each extension [RFC8200], so the typical (and largest valid) value for UDP Length is: UDP_Length = IPv6_Payload_Length - sum(extension header lengths) Touch Expires September 1, 2022 [Page 5] Internet-Draft Transport Options for UDP March 2022 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Version| Traffic Class | Flow Label | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload Length | Next Hdr | Hop Limit | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... | Source Address (128 bits) | ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... | Destination Address (128 bits) | ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... zero or more IP Extension headers (each indicating size) ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Source Port | UDP Destination Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Length | UDP Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IPv6 datagram with UDP transport payload In both cases, the space available for the UDP transport protocol data unit is indicated by IP, either directly in the base header (for IPv4) or by adding information in the extensions (for IPv6). In either case, this document will refer to this available space as the "IP transport payload". As a result of this redundancy, there is an opportunity to use the UDP Length field as a way to break up the IP transport payload into two areas - that intended as UDP user data and an additional "surplus area" (as shown in Figure 3). IP transport payload <-------------------------------------------------> +--------+---------+----------------------+------------------+ | IP Hdr | UDP Hdr | UDP user data | surplus area | +--------+---------+----------------------+------------------+ <------------------------------> UDP Length IP transport payload vs. UDP Length In most cases, the IP transport payload and UDP Length point to the same location, indicating that there is no surplus area. This is not a requirement of UDP [RFC768] (discussed further in Section 15). For Touch Expires September 1, 2022 [Page 6] Internet-Draft Transport Options for UDP March 2022 example, UDP-Lite used the difference in these pointers to indicate the partial coverage of the UDP Checksum, such that the UDP user data, UDP header, and UDP pseudoheader (a subset of the IP header) are covered by the UDP checksum but additional user data in the surplus area is not covered [RFC3828]. This document uses the surplus area for UDP transport options. The UDP option area is thus defined as the location between the end of the UDP payload and the end of the IP datagram as a trailing options area. This area can commence at any valid byte offset, i.e., it need not be 16-bit or 32-bit aligned. In effect, this document redefines the UDP "Length" field as a "trailer offset". 5. The UDP Option Area Structure UDP options use the entire surplus area, i.e., after the last byte of the UDP payload as implied by the IP header. They commence with a 2-byte Option Checksum (OCS) field aligned to the first 4-byte boundary (relative to the start of the IP packet) of that area, using zeroes for alignment. The UDP option area can be used with any UDP payload length (including zero), as long as there remains enough space for the aligned OCS and the options used. >> UDP options MAY begin at any UDP length offset. >> Option area bytes used for alignment before the OCS MUST be zero. The OCS contains an optional ones-complement sum that detects errors in the surplus area, which is not otherwise covered by the UDP checksum, as detailed in Section 6. The remainder of the UDP option area consists of options defined using a TLV (type, length, and optional value) syntax similar to that of TCP [RFC793], as detailed in Section 7. These options continue until the end of the surplus area or can end earlier using the EOL (end of list) option, followed by zeroes. 6. The Option Checksum (OCS) The Option Checksum (OCS) option is conventional Internet checksum [RFC791] that detects errors in the surplus area. The OCS option contains a 32-bit checksum that is aligned to the first 4-byte boundary, preceded by zeroes for padding (if needed), as shown in Figure 4. Touch Expires September 1, 2022 [Page 7] Internet-Draft Transport Options for UDP March 2022 +--------+--------+--------+--------+ | UDP data | 0 | +--------+--------+--------+--------+ | OCS | UDP options... | +--------+--------+--------+--------+ UDP OCS format, here using one zero for alignment The OCS consists of a 16-bit Internet checksum [RFC1071], computed over the surplus area and including the length of the surplus area as an unsigned 16-bit value. The OCS protects the option area from errors in a similar way that the UDP checksum protects the UDP user data (when not zero). The primary purpose of the OCS is to detect non-standard (i.e., non- option) uses of that area and accidental errors. It is not intended to detect attacks, as discussed further in Section 21. The surplus area length is included in the OCS calculation to enable traversal of errant middleboxes that incorrectly compute the UDP checksum over the entire IP payload rather than only the UDP payload [Fa18]. Like the UDP checksum, OCS use is optional and contains zero when not used. UDP checksums can be zero for IPv4 [RFC791] and for IPv6 [RFC8200] when UDP payload already covered by another checksum, as might occur for tunnels [RFC6935]. The same exceptions apply to the OCS, as well as for its use in UDP fragmentation (see Section 8.4). The OCS covers the UDP option area as formatted for transmission and is processed immediately upon reception. >> If the OCS fails, all options MUST be ignored and the surplus area silently discarded. >> UDP data that is validated by a correct UDP checksum MUST be delivered to the application layer, even if the OCS fails, unless the endpoints have negotiated otherwise for this segment's socket pair. When not used (i.e., containing zero), the OCS is assumed to be "correct" for the purpose of accepting UDP packets at a receiver (see Section 11). Touch Expires September 1, 2022 [Page 8] Internet-Draft Transport Options for UDP March 2022 7. UDP Options UDP options are typically a minimum of two bytes in length as shown in Figure 5, excepting only the one byte options "No Operation" (NOP) and "End of Options List" (EOL) described below. +--------+--------+------- | Kind | Length | (remainder of option...) +--------+--------+------- UDP option default format The Kind field is always one byte. The Length field is one byte for all lengths below 255 (including the Kind and Length bytes). A Length of 255 indicates use of the UDP option extended format shown in Figure 6. The Extended Length field is a 16-bit field in network standard byte order. +--------+--------+--------+--------+ | Kind | 255 | Extended Length | +--------+--------+--------+--------+ | (remainder of option...) +--------+--------+--------+--------+ UDP option extended format >> The UDP length MUST be at least as large as the UDP header (8) and no larger than the IP transport payload. Datagrams with length values outside this range MUST be silently dropped as invalid and logged where rate-limiting permits. >> Option Lengths (or Extended Lengths, where applicable) smaller than the minimum for the corresponding Kind MUST be treated as an error. Such errors call into question the remainder of the option area and thus MUST result in all UDP options being silently discarded. >> Any UDP option other than EOL and NOP MAY use either the default or extended option formats. >> Any UDP option whose length is larger than 254 MUST use the UDP option extended format shown in Figure 6. >> For compactness, UDP options SHOULD use the smallest option format possible. Touch Expires September 1, 2022 [Page 9] Internet-Draft Transport Options for UDP March 2022 >> UDP options MUST be interpreted in the order in which they occur in the UDP option area. The following UDP options are currently defined: Kind Length Meaning ---------------------------------------------- 0* - End of Options List (EOL) 1* - No operation (NOP) 2* 6 Alternate payload checksum (APC) 3* 10/12 Fragmentation (FRAG) 4* 4 Maximum segment size (MSS) 5* 4 Maximum reassembled segment size (MRSS) 6* 6 Request (REQ) 7* 6 Response (RESP) 8 10 Timestamps (TIME) 9 (varies) Authentication (AUTH) 10-126 (varies) UNASSIGNED (assignable by IANA) 127 (varies) RFC 3692-style experiments (EXP) 128-191 RESERVED 193 (varies) Encryption (UENC) 194-253 UNASSIGNED-UNSAFE (assignable by IANA) 254 (varies) RFC 3692-style experiments (UEXP) 255 RESERVED-UNSAFE Options indicated by Kind values in the range 0..191 are known as SAFE options because they do not alter the UDP data payload and thus do not interfere with use of that data by legacy endpoints. Options indicated by Kind values in the range 192..255 are known as UNSAFE options because they do alter the UDP data payload and thus would interfere with legacy endpoints. UNSAFE option nicknames are expected to begin with "U", which should be avoided for safe option nicknames (see Section 22). Although the FRAG option modifies the original UDP payload contents (i.e., is UNSAFE with respect to the original UDP payload), it is used only in subsequent fragment segments with zero UDP payloads, thus is SAFE in actual use, as discussed further in Section 8.4. These options are defined in the following subsections. Options 0 and 1 use the same values as for TCP. >> An endpoint supporting UDP options MUST support those marked with a "*" above: EOL, NOP, APC, FRAG, MSS, MRSS, REQ, and RESP. This includes both recognizing and being able to generate these options if configured to do so. These are called "must-support" options. Touch Expires September 1, 2022 [Page 10] Internet-Draft Transport Options for UDP March 2022 >> An endpoint supporting UDP options MUST treat unsupported options in the UNSAFE range as terminating all option processing. >> All other SAFE options (without a "*") MAY be implemented, and their use SHOULD be determined either out-of-band or negotiated, notably if needed to detect when options are silently ignored by legacy receivers. >> Receivers supporting UDP options MUST silently ignore unknown SAFE options (i.e., in the same way a legacy receiver would). That includes options whose length does not indicate the specified value(s), as long as the length is not inherently invalid (i.e., smaller than 2 for the default and 4 for the extended formats). >> UNSAFE options are used only in with the FRAG option, in a manner that prevents them from being silently ignored but passing the UDP payload to the user when not supported. This ensures their safe use in environments that might include legacy receivers (See Section 9). >> Receivers supporting UDP options MUST silently drop the entire datagram containing an UNSAFE option when any UNSAFE option it contains is unknown. See Section 9 for further discussion of UNSAFE options. >> Except for NOP, EXP, and UEXP, each option SHOULD NOT occur more than once in a single UDP datagram. If an option other than these occurs more than once, a receiver MUST interpret only the first instance of that option and MUST ignore all others. >> EXP and UEXP MAY occur more than once, but SHOULD NOT occur more than once using the same ExID (see Sections 8.10 and 9.2). >> Only the OCS and the AUTH and ENCR options depend on the contents of the option area. AUTH and UENC are never used together, as UENC would serve both purposes. AUTH and UENC are always computed as if their hash and the OCS are zero; the OCS is always computed as if its contents are zero and after the AUTH or UENC hash has been computed. Future options MUST NOT be defined as having a value dependent on the contents of the option area. Otherwise, interactions between those values, the OCS, and the AUTH and UENC options could be unpredictable. Receivers cannot generally treat unexpected option lengths as invalid, as this would unnecessarily limit future revision of options (e.g., defining a new APC that is defined by having a different length). The exception is only for lengths that imply a physical impossibility, e.g., smaller than two for conventional Touch Expires September 1, 2022 [Page 11] Internet-Draft Transport Options for UDP March 2022 options and four for extended length options. Impossible lengths should indicate a malformed option area and all options silently discarded. Lengths other than expected should result in safe options being ignored and that length skipped over, as with any other unknown safe option. >> Option lengths MUST NOT exceed the IP length of the packet. If this occurs, the packet MUST be treated as malformed and dropped, and the event MAY be logged for diagnostics (logging SHOULD be rate limited). >> "Must-support" options other than NOP and EOL MUST come before other options. The requirement that must-support options come before others is intended to allow for endpoints to implement DOS protection, as discussed further in Section 21. 8. Safe UDP Options Safe UDP options can be silently ignored by legacy receivers without affecting the meaning of the UDP payload data. They stand in contrast to Unsafe options, which modify UDP payload data in ways that render it unusable by legacy receivers (Section 9). The following subsections describe safe options defined in this document. 8.1. End of Options List (EOL) The End of Options List (EOL) option indicates that there are no more options. It is used to indicate the end of the list of options without needing to use NOP options (see the following section) as padding to fill all available option space. +--------+ | Kind=0 | +--------+ UDP EOL option format >> When the UDP options do not consume the entire option area, the last non-NOP option MUST be EOL. >> NOPs SHOULD NOT be used as padding before the EOL option. As a one byte option, it need not be otherwise aligned. Touch Expires September 1, 2022 [Page 12] Internet-Draft Transport Options for UDP March 2022 >> All bytes in the surplus area after EOL MUST be set to zero on transmit. >> Bytes after EOL in the surplus area MAY be checked as being zero on receipt but MUST be treated as zero regardless of their content and are not passed to the user (e.g., as part of the UDP option area). Requiring the post-option surplus area to be zero prevents side- channel uses of this area, requiring instead that all use of the surplus area be UDP options supported by both endpoints. It is useful to allow this area to be used for zero padding to increase the packet length without affecting the payload length, e.g., for UDP DPLPMTUD [Fa22]. 8.2. No Operation (NOP) The No Operation (NOP) option is a one byte placeholder, intended to be used as padding, e.g., to align multi-byte options along 16-bit or 32-bit boundaries. +--------+ | Kind=1 | +--------+ UDP NOP option format >> Segments SHOULD NOT use more than seven consecutive NOPs, i.e., to support alignment up to 8-byte boundaries. Segments SHOULD use NOPs at the end of the options area as a substitute for EOL followed by zero-fill. NOPs are intended to assist with alignment, not as other padding or fill. This issue is discussed further in Section 21. 8.3. Alternate Payload Checksum (APS) The Alternate Payload Checksum (APC) option provides a stronger alternative to the checksum in the UDP header, using a 32-bit CRC of the conventional UDP payload only (excluding the IP pseudoheader, UDP header, and surplus area). It is an "alternate" to the UDP checksum that covers the UDP payload - not to the OCS (the latter covers the surplus area only). Unlike the UDP checksum, APC does not include the IP pseudoheader or UDP header, thus it does not need to be updated by NATs when IP addresses or UDP ports are rewritten. Its purpose is to detect UDP payload errors that the UDP checksum, when used, might not detect. Touch Expires September 1, 2022 [Page 13] Internet-Draft Transport Options for UDP March 2022 A CRC32c has been chosen because of its ubiquity and use in other Internet protocols, including iSCSI and SCTP. The option contains the CRC32c in network standard byte order, as described in [RFC3385]. +--------+--------+--------+--------+ | Kind=2 | Len=6 | CRC32c... | +--------+--------+--------+--------+ | CRC32c (cont.) | +--------+--------+ UDP APC option format When present, the APC always contains a valid CRC checksum. There are no reserved values, including the value of zero. If the CRC is zero, this must indicate a valid checksum (i.e., it does not indicate that the APC is not used; instead, the option would simply not be included if that were the desired effect). APC does not protect the UDP pseudoheader; only the current UDP checksum provides that protection (when used). APC cannot provide that protection because it would need to be updated whenever the UDP pseudoheader changed, e.g., during NAT address and port translation; because this is not the case, APC does not cover the pseudoheader. >> Packets with incorrect APC checksums MUST be passed to the application by default, e.g., with a flag indicating APC failure. Like all safe UDP options, APC needs to be silently ignored when failing by default, unless the receiver has been configured to do otherwise. Although all UDP option-aware endpoints support APC (being in the required set), this silently-ignored behavior ensures that option-aware receivers operate the same as legacy receivers unless overridden. >> Packets with unrecognized APC lengths MUST be receive the same treatment as packets with incorrect APC checksums. Ensuring that unrecognized APC lengths are treated as incorrect checksums enables future variants of APC to be treated as APC-like. 8.4. Fragmentation (FRAG) The Fragmentation (FRAG) option supports UDP fragmentation and reassembly, which can be used to transfer UDP messages larger than limited by the IP receive MTU (EMTU_R [RFC1122]). FRAG includes a copy of the same UDP transport ports in each fragment, enabling them Touch Expires September 1, 2022 [Page 14] Internet-Draft Transport Options for UDP March 2022 to traverse Network Address (and port) Translation (NAT) devices, in contrast to the behavior of IP fragments. FRAG is typically used with the UDP MSS and MRSS options to enable more efficient use of large messages, both at the UDP and IP layers. FRAG is designed similar to the IPv6 Fragmentation Header [RFC8200], except that the UDP variant uses a 16-bit Offset measured in bytes, rather than IPv6's 13-bit Fragment Offset measured in 8-byte units. This UDP variant avoids creating reserved fields. >> When FRAG is present, it SHOULD come as early as possible in the UDP options list. >> When FRAG is present, the UDP payload MUST be empty. If the payload is not empty, all UDP options MUST be silently ignored and the payload received sent to the user. Legacy receivers interpret FRAG messages as zero-length payload packets (i.e., UDP Length field is 8, the length of just the UDP header), which would not affect the receiver unless the presence of the packet itself were a signal (see Section 5 of [RFC8085]). In this manner, the FRAG option also helps hide UNSAFE options so they can be used more safely in the presence of legacy receivers. The FRAG option has two formats; non-terminal fragments use the shorter variant (Figure 10) and terminal fragments use the longer (Figure 11). The latter includes stand-alone fragments, i.e., when data is contained in the FRAG option but reassembly is not required. +--------+--------+--------+--------+ | Kind=3 | Len=10 | Frag. Start | +--------+--------+--------+--------+ | Identification | +--------+--------+--------+--------+ | Frag. Offset | +--------+--------+ UDP non-terminal FRAG option format In the non-terminal FRAG option format, Frag. Start indicates the location of the beginning of the fragment data, measured from the beginning of the UDP header, which always follows the remainder of the UDP options. Those options are applied to this segment. The fragment data begins at Frag. Start and ends at the end of the IP datagram. Non-terminal fragments never have options after the fragment. Touch Expires September 1, 2022 [Page 15] Internet-Draft Transport Options for UDP March 2022 The FRAG option does not need a "more fragments" bit because it provides the same indication by using the longer, 12-byte variant, as shown in Figure 11. >> The FRAG option MAY be used on a single fragment, in which case the Frag. Offset would be zero and the option would have the 12-byte format. >> Endpoints supporting UDP options MUST be capable of fragmenting and reassembling at least 2 fragments, for a total of at least 3,000 bytes (see MRSS in Section 8.6). Use of the single fragment variant can be helpful in supporting use of UNSAFE options without undesirable impact to receivers that do not support either UDP options or the specific UNSAFE options. +--------+--------+--------+--------+ | Kind=4 | Len=12 | Frag. Start | +--------+--------+--------+--------+ | Identification | +--------+--------+--------+--------+ | Frag. Offset | Frag. End | +--------+--------+--------+--------+ UDP terminal FRAG option format The terminal FRAG option format adds a Frag. End pointer, measured from the start of the UDP header, as with Frag. Start. In this variant, UDP options continue after the terminal fragment data. UDP options that occur before the FRAG data are processed on the fragment; UDP options after the FRAG data are processed after reassembly, such that the reassembled data represents the original UDP user data. This allows either pre-reassembly or post-reassembly UDP option effects, such as using UENC on each fragment while also using TIME on the reassembled datagram for round-trip latency measurements. >> During fragmentation, the UDP header checksum of each fragment needs to be recomputed based on each datagram's pseudoheader. The Fragment Offset is 16 bits and indicates the location of the UDP payload fragment in bytes from the beginning of the original unfragmented payload. The option Len field indicates whether there are more fragments (Len=10) or no more fragments (Len=12). >> The Identification field is a 32-bit value that MUST be unique over the expected fragment reassembly timeout. Touch Expires September 1, 2022 [Page 16] Internet-Draft Transport Options for UDP March 2022 >> The Identification field SHOULD be generated in a manner similar to that of the IPv6 Fragment ID [RFC8200]. >> UDP fragments MUST NOT overlap. Similar to IPv6 reassembly [RFC8200], if any of the fragments being reassembled overlap with any other fragments being reassembled for the same packet, reassembly of that packet must be abandoned and all the fragments that have been received for that packet must be discarded, and no ICMP error messages should be sent. It should be noted that fragments may be duplicated in the network. Instead of treating these exact duplicate fragments as overlapping fragments, an implementation may choose to detect this case and drop exact duplicate fragments while keeping the other fragments belonging to the same packet. UDP fragmentation relies on a fragment expiration timer, which can be preset or could use a value computed using the UDP Timestamp option. >> The default UDP reassembly SHOULD be no more than 2 minutes. >> UDP reassembly space SHOULD be limited to reduce the impact of DOS attacks on resource use. >> UDP reassembly space limits SHOULD NOT be computed as a shared resource across multiple sockets, to avoid cross-socketpair DOS attacks. >> Individual UDP fragments MUST NOT be forwarded to the user. The reassembled datagram is received only after complete reassembly, checksum validation, and continued processing of the remaining UDP options. Any per-datagram UDP options, if used, follow the FRAG option in the final fragment and would be included in the reassembled packet. Processing of those options would commence after reassembly. This is especially important for UNSAFE options, which are interpreted only after FRAG. In general, UDP packets are fragmented as follows: Touch Expires September 1, 2022 [Page 17] Internet-Draft Transport Options for UDP March 2022 1. Create a datagram with data and UDP options, which we will call "D". Note that the UDP options treat the data area as UDP user data and thus must follow that data. Process these UDP options before the rest of the fragmentation steps below. 2. Identify the desired fragment size, which we will call "S". This value should take into account the path MTU (if known) and allow space for per-fragment options. 3. Fragment "D" into chunks of size no larger than "S"-10 each, with one final chunk no larger than "S"-12. Note that all the non-FRAG options in step #1 MUST appear in the terminal fragment. 4. For each chunk of "D" in step #3, create a zero-data UDP packet followed by the word-aligned OCS, the FRAG option, and any additional UDP options, followed by the FRAG data chunk. The last chunk includes the non-FRAG options noted in step #1 after the end of the FRAG data. These UDP options apply to the reassembled data as a whole when received. 5. Process the pre-reassembly UDP options of each fragment. Receivers reverse the above sequence. They process all received options in each fragment. When the FRAG option is encountered, the FRAG data is used in reassembly. After all fragments are received, the entire packet is processed with any trailing UDP options applying to the reassembled data. 8.5. Maximum Segment Size (MSS) The Maximum Segment Size (MSS, Kind = 5) option is a 16-bit hint of the largest unfragmented UDP segment that an endpoint believes can be received. As with the TCP MSS option [RFC793], the size indicated is the IP layer MTU decreased by the fixed IP and UDP headers only [RFC6691]. The space needed for IP and UDP options need to be adjusted by the sender when using the value indicated. The value transmitted is based on EMTU_R, the largest IP datagram that can be received (i.e., reassembled at the receiver) [RFC1122]. However, as with TCP, this value is only a hint at what the receiver believes; it does not indicate a known path MTU and thus MUST NOT be used to limit transmissions, notably for DPLPMTU probes. Touch Expires September 1, 2022 [Page 18] Internet-Draft Transport Options for UDP March 2022 +--------+--------+--------+--------+ | Kind=4 | Len=4 | MSS size | +--------+--------+--------+--------+ UDP MSS option format The UDP MSS option MAY be used as a hint for path MTU discovery [RFC1191][RFC8201], but this may be difficult because of known issues with ICMP blocking [RFC2923] as well as UDP lacking automatic retransmission. It is more likely to be useful when coupled with IP source fragmentation to limit the largest reassembled UDP message as indicated by MRSS (see Section 8.6), e.g., when EMTU_R is larger than the required minimums (576 for IPv4 [RFC791] and 1500 for IPv6 [RFC8200]). It can also be used with DPLPMTUD [RFC8899] to provide a hint to maximum DPLPMTU, though it MUST NOT prohibit transmission of larger UDP packets (or fragments) used as DPLPMTU probes. 8.6. Maximum Reassembled Segment Size (MRSS) The Maximum Reassembled Segment Size (MRSS, Kind=6) option is a 16- bit indicator of the largest reassembled UDP segment that can be received. MRSS is the UDP equivalent of IP's EMTU_R but the two are not related [RFC1122]. Using the FRAG option (Section 8.4), UDP segments can be transmitted as transport fragments, each in their own (presumably not fragmented) IP datagram and be reassembled at the UDP layer. +--------+--------+--------+--------+ | Kind=5 | Len=4 | MRSS size | +--------+--------+--------+--------+ UDP MRSS option format >> Endpoints supporting UDP options MUST support a local MRSS of at least 3,000 bytes. 8.7. Echo request (REQ) and echo response (RES) The echo request (REQ, kind=6) and echo response (RES, kind=7) options provide a means for UDP options to be used to provide packet-level acknowledgements. One such use is described as part of the UDP options variant of packetization layer path MTU discovery (PLPMTUD) [Fa22]. The options both have the format indicated in Figure 14, in which the token has no internal structure or meaning. Touch Expires September 1, 2022 [Page 19] Internet-Draft Transport Options for UDP March 2022 +--------+--------+------------------+ | Kind | Len=6 | token | +--------+--------+------------------+ 1 byte 1 byte 4 bytes UDP REQ and RES options format Each of these option kinds appears at most once in each UDP datagram, as with other options. Note also that the FRAG option is not used when sending DPLPMTUD probes to determine a PLPMTU [Fa22]. 8.8. Timestamps (TIME) The Timestamp (TIME) option exchanges two four-byte timestamp fields. It serves a similar purpose to TCP's TS option [RFC7323], enabling UDP to estimate the round trip time (RTT) between hosts. For UDP, this RTT can be useful for establishing UDP fragment reassembly timeouts or transport-layer rate-limiting [RFC8085]. +--------+--------+------------------+------------------+ | Kind=8 | Len=10 | TSval | TSecr | +--------+--------+------------------+------------------+ 1 byte 1 byte 4 bytes 4 bytes UDP TIME option format TS Value (TSval) and TS Echo Reply (TSecr) are used in a similar manner to the TCP TS option [RFC7323]. On transmitted segments using the option, TS Value is always set based on the local "time" value. Received TSval and TSecr values are provided to the application, which can pass the TSval value to be used as TSecr on UDP messages sent in response (i.e., to echo the received TSval). A received TSecr of zero indicates that the TSval was not echoed by the transmitter, i.e., from a previously received UDP packet. >> TIME MAY use an RTT estimate based on nonzero Timestamp values as a hint for fragmentation reassembly, rate limiting, or other mechanisms that benefit from such an estimate. >> an application MAY use TIME to compute this RTT estimate for further use by the user. UDP timestamps are modeled after TCP timestamps and have similar expectations. In particular, they are expected to be: o Values are monotonic and non-decreasing except for anticipated number-space rollover events Touch Expires September 1, 2022 [Page 20] Internet-Draft Transport Options for UDP March 2022 o Values should "increase" (allowing for rollover) according to a typical 'tick' time o A request is defined as TSval being non-zero and a reply is defined as TSecr being non-zero. o A receiver should always respond to a request with the highest TSval received (allowing for rollover), which is not necessarily the most recently received. Rollover can be handled as a special case or more completely using sequence number extension [RFC9187], however zero values need to be avoided. >> TIME values MUST NOT use zeros as valid time values, because they are used as indicators of requests and responses. 8.9. Authentication (AUTH) The Authentication (AUTH) option is intended to allow UDP to provide a similar type of authentication as the TCP Authentication Option (TCP-AO) [RFC5925]. AUTH covers the conventional UDP payload. It uses the same format as specified for TCP-AO, except that it uses a Kind of 10. AUTH supports NAT traversal in a similar manner as TCP- AO [RFC6978]. +--------+--------+--------+--------+ | Kind=9 | Len | Digest... | +--------+--------+--------+--------+ | Digest (con't)... | +--------+--------+--------+--------+ UDP AUTH option format Like TCP-AO, AUTH is not negotiated in-band. Its use assumes both endpoints have populated Master Key Tuples (MKTs), used to exclude non-protected traffic. TCP-AO generates unique traffic keys from a hash of TCP connection parameters. UDP lacks a three-way handshake to coordinate connection-specific values, such as TCP's Initial Sequence Numbers (ISNs) [RFC793], thus AUTH's Key Derivation Function (KDF) uses zeroes as the value for both ISNs. This means that the AUTH reuses keys when socket pairs are reused, unlike TCP-AO. >> Packets with incorrect AUTH HMACs MUST be passed to the application by default, e.g., with a flag indicating AUTH failure. Touch Expires September 1, 2022 [Page 21] Internet-Draft Transport Options for UDP March 2022 Like all non-UNSAFE UDP options, AUTH needs to be silently ignored when failing. This silently-ignored behavior ensures that option- aware receivers operate the same as legacy receivers unless overridden. In addition to the UDP payload (which is always included), AUTH can be configured to either include or exclude the surplus area, in a similar way as can TCP-AO can optionally exclude TCP options. When UDP options are covered, the OCS value and AUTH (and later, UENC) hash areas are zeroed before computing the AUTH hash. It is important to consider that options not yet defined might yield unpredictable results if not confirmed as supported, e.g., if they were to contain other hashes or checksums that depend on the option area contents. This is why such dependencies are not permitted except as defined for the OCS and the AUTH (and later, UENC) option. Similar to TCP-AO-NAT, AUTH (and later, UENC) can be configured to support NAT traversal, excluding (by zeroing out) one or both of the UDP ports and corresponding IP addresses [RFC6978]. 8.10. Experimental (EXP) The Experimental option (EXP) is reserved for experiments [RFC3692]. It uses a Kind value of 127. Only one such value is reserved because experiments are expected to use an Experimental ID (ExIDs) to differentiate concurrent use for different purposes, using UDP ExIDs registered with IANA according to the approach developed for TCP experimental options [RFC6994]. +----------+----------+----------+----------+ | Kind=127 | Len | UDP ExID | +----------+----------+----------+----------+ | (option contents, as defined)... | +----------+----------+----------+----------+ UDP EXP option format >> The length of the experimental option MUST be at least 4 to account for the Kind, Length, and the minimum 16-bit UDP ExID identifier (similar to TCP ExIDs [RFC6994]). The UDP EXP option also includes an extended length format, where the option LEN is 255 followed by two bytes of extended length. Touch Expires September 1, 2022 [Page 22] Internet-Draft Transport Options for UDP March 2022 +----------+----------+----------+----------+ | Kind=127 | 255 | Extended Length | +----------+----------+----------+----------+ | UDP ExID. |(option contents...) | +----------+----------+----------+----------+ UDP EXP option format Assigned UDP experimental IDs (ExIDs) assigned from a single registry managed by IANA (see Section 22). Assigned ExIDs can be used in either the EXP or UEXP options (see Section 9.2 for the latter). 9. UNSAFE Options UNSAFE options are not safe to ignore and can be used unidirectionally or without soft-state confirmation of UDP option capability. They are always used only when the entire UDP payload occurs inside a reassembled set of one or more UDP fragments, such that if UDP fragmentation is not supported, the entire fragment would be silently dropped anyway. >> UNSAFE options MUST be used only as part of UDP fragments, used either per-fragment or after reassembly. >> Receivers supporting UDP options MUST silently drop the entire reassembled datagram if any fragment or the entire datagram includes an UNSAFE option whose UKind is not supported. 9.1. UNSAFE Encryption (UENC) UNSAFE encryption (UENC) has the same format as AUTH (Section 8.9), except that it encrypts (modifies) the user data. It provides a similar encryption capability as TCP-AO-ENC, in a similar manner [To18]. Its fields, coverage, and processing are the same as for AUTH, except that UENC encrypts only the user data, although it can (optionally) depend on the option area (with certain fields zeroed, as per AUTH, e.g., providing authentication over the option area). Like AUTH, UENC can be configured to be compatible with NAT traversal. 9.2. UNSAFE Experimental (UEXP) The UNSAFE Experimental option (EXP) is reserved for experiments [RFC3692]. It uses a Kind value of 254. Only one such value is reserved because experiments are expected to use an Experimental ID (ExIDs) to differentiate concurrent use for different purposes, Touch Expires September 1, 2022 [Page 23] Internet-Draft Transport Options for UDP March 2022 using UDP ExIDs registered with IANA according to the approach developed for TCP experimental options [RFC6994]. Assigned ExIDs can be used with either the UEXP or EXP options. 10. Rules for designing new options The UDP option Kind space allows for the definition of new options, however the currently defined options do not allow for arbitrary new options. The following is a summary of rules for new options and their rationales: >> New options MUST NOT modify other option content. >> New options MUST NOT depend on the content of other options. >> UNSAFE options can both depend on and vary user data content because they are contained only inside UDP fragments and thus are processed only by UDP option capable receivers. >> New options MUST NOT declare their order relative to other options, whether new or old. >> At the sender, new options MUST NOT modify UDP packet content anywhere except within their option field, excepting only those contained within the UNSAFE option; areas that need to remain unmodified include the IP header, IP options, the UDP body, the UDP option area (i.e., other options), and the post-option area. >> Options MUST NOT be modified in transit. This includes those already defined as well as new options. >> New options MUST NOT require or intend optionally for modification of any UDP options, including their new areas, in transit. Note that only certain of the initially defined options violate these rules: o >> Only FRAG and UNSAFE options are permitted to modify the UDP body. The following recommendation helps enable efficient zero-copy processing: o >> FRAG SHOULD be the first option, when present. Touch Expires September 1, 2022 [Page 24] Internet-Draft Transport Options for UDP March 2022 11. Option inclusion and processing The following rules apply to option inclusion by senders and processing by receivers. >> Senders MAY add any option, as configured by the API. >> All mandatory options MUST be processed by receivers, if present (presuming UDP options are supported at that receiver). >> Non-mandatory options MAY be ignored by receivers, if present, e.g., based on API settings. >> All options MUST be processed by receivers in the order encountered in the options area. >> All options except UNSAFE options MUST result in the UDP payload being passed to the application layer, regardless of whether all options are processed, supported, or succeed. The basic premise is that, for options-aware endpoints, the sender decides what options to add and the receiver decides what options to handle. Simply adding an option does not force work upon a receiver, with the exception of the mandatory options. Upon receipt, the receiver checks various properties of the UDP packet and its options to decide whether to accept or drop the packet and whether to accept or ignore some its options as follows (in order): if the UDP checksum fails then silently drop (per RFC1122) if the UDP checksum passes then if OCS is nonzero and fails then deliver the UDP payload but ignore all other options (this is required to emulate legacy behavior) if OCS is nonzero and passes or is zero then deliver the UDP payload after parsing and processing the rest of the options, regardless of whether each is supported or succeeds (again, this is required to emulate legacy behavior) The design of the UNSAFE options as used only inside the FRAG area ensures that the resulting UDP data will be silently dropped in both legacy and options-aware receivers. Touch Expires September 1, 2022 [Page 25] Internet-Draft Transport Options for UDP March 2022 Options-aware receivers can either drop packets with option processing errors via an override of the default or at the application layer. I.e., all options are treated the same, in that the transmitter can add it as desired and the receiver has the option to require it or not. Only if it is required (e.g., by API configuration) should the receiver require it being present and correct. I.e., for all options: o if the option is not required by the receiver, then packets missing the option are accepted. o if the option is required (e.g., by override of the default behavior at the receiver) and missing or incorrectly formed, silently drop the packet. o if the packet is accepted (either because the option is not required or because it was required and correct), then pass the option with the packet via the API. Any options whose length exceeds that of the UDP packet (i.e., intending to use data that would have been beyond the surplus area) should be silently ignored (again to model legacy behavior). 12. UDP API Extensions UDP currently specifies an application programmer interface (API), summarized as follows (with Unix-style command as an example) [RFC768]: o Method to create new receive ports oE .g., bind(handle, recvaddr(optional), recvport) o Receive, which returns data octets, source port, and source address oE .g., recvfrom(handle, srcaddr, srcport, data) o Send, which specifies data, source and destination addresses, and source and destination ports oE .g., sendto(handle, destaddr, destport, data) This API is extended to support options as follows: Touch Expires September 1, 2022 [Page 26] Internet-Draft Transport Options for UDP March 2022 o Extend the method to create receive ports to include receive options that are required. Datagrams not containing these required options MUST be silently dropped and MAY be logged. o Extend the receive function to indicate the options and their parameters as received with the corresponding received datagram. o Extend the send function to indicate the options to be added to the corresponding sent datagram. Examples of API instances for Linux and FreeBSD are provided in Appendix A, to encourage uniform cross-platform implementations. 13. UDP Options are for Transport, Not Transit UDP options are indicated in an area of the IP payload that is not used by UDP. That area is really part of the IP payload, not the UDP payload, and as such, it might be tempting to consider whether this is a generally useful approach to extending IP. Unfortunately, the surplus area exists only for transports that include their own transport layer payload length indicator. TCP and SCTP include header length fields that already provide space for transport options by indicating the total length of the header area, such that the entire remaining area indicated in the network layer (IP) is transport payload. UDP-Lite already uses the UDP Length field to indicate the boundary between data covered by the transport checksum and data not covered, and so there is no remaining area where the length of the UDP-Lite payload as a whole can be indicated [RFC3828]. UDP options are intended for use only by the transport endpoints. They are no more (or less) appropriate to be modified in-transit than any other portion of the transport datagram. UDP options are transport options. Generally, transport datagrams are not intended to be modified in-transit. UDP options are no exception and here are specified as "MUST NOT" be altered in transit. However, the UDP option mechanism provides no specific protection against in-transit modification of the UDP header, UDP payload, or UDP option area, except as provided by the OCS or the options selected (e.g., AUTH, or UENC). 14. UDP options vs. UDP-Lite UDP-Lite provides partial checksum coverage, so that packets with errors in some locations can be delivered to the user [RFC3828]. It Touch Expires September 1, 2022 [Page 27] Internet-Draft Transport Options for UDP March 2022 uses a different transport protocol number (136) than UDP (17) to interpret the UDP Length field as the prefix covered by the UDP checksum. UDP (protocol 17) already defines the UDP Length field as the limit of the UDP checksum, but by default also limits the data provided to the application as that which precedes the UDP Length. A goal of UDP-Lite is to deliver data beyond UDP Length as a default, which is why a separate transport protocol number was required. UDP options do not use or need a separate transport protocol number because the data beyond the UDP Length offset (surplus data) is not provided to the application by default. That data is interpreted exclusively within the UDP transport layer. UDP-Lite cannot support UDP options, either as proposed here or in any other form, because the entire payload of the UDP packet is already defined as user data and there is no additional field in which to indicate a separate area for options. The UDP Length field in UDP-Lite is already used to indicate the boundary between user data covered by the checksum and user data not covered. 15. Interactions with Legacy Devices It has always been permissible for the UDP Length to be inconsistent with the IP transport payload length [RFC768]. Such inconsistency has been utilized in UDP-Lite using a different transport number. There are no known systems that use this inconsistency for UDP [RFC3828]. It is possible that such use might interact with UDP options, i.e., where legacy systems might generate UDP datagrams that appear to have UDP options. The OCS provides protection against such events and is stronger than a static "magic number". UDP options have been tested as interoperable with Linux, macOS, and Windows Cygwin, and worked through NAT devices. These systems successfully delivered only the user data indicated by the UDP Length field and silently discarded the surplus area. One reported embedded device passes the entire IP datagram to the UDP application layer. Although this feature could enable application-layer UDP option processing, it would require that conventional UDP user applications examine only the UDP payload. This feature is also inconsistent with the UDP application interface [RFC768] [RFC1122]. It has been reported that Alcatel-Lucent's "Brick" Intrusion Detection System has a default configuration that interprets Touch Expires September 1, 2022 [Page 28] Internet-Draft Transport Options for UDP March 2022 inconsistencies between UDP Length and IP Length as an attack to be reported. Note that other firewall systems, e.g., CheckPoint, use a default "relaxed UDP length verification" to avoid falsely interpreting this inconsistency as an attack. 16. Options in a Stateless, Unreliable Transport Protocol There are two ways to interpret options for a stateless, unreliable protocol -- an option is either local to the message or intended to affect a stream of messages in a soft-state manner. Either interpretation is valid for defined UDP options. It is impossible to know in advance whether an endpoint supports a UDP option. >> All UDP options other than UNSAFE ones MUST be ignored if not supported or upon failure (e.g., APC). >> All UDP options that fail MUST result in the UDP data still being sent to the application layer by default, to ensure equivalence with legacy devices. >> UDP options that rely on soft-state exchange MUST allow for message reordering and loss. The above requirements prevent using any option that cannot be safely ignored unless it is hidden inside the FRAG area (i.e., UNSAFE options). Legacy systems also always need to be able to interpret the transport payload fragments as individual transport datagrams. 17. UDP Option State Caching Some TCP connection parameters, stored in the TCP Control Block, can be usefully shared either among concurrent connections or between connections in sequence, known as TCP Sharing [RFC9040]. Although UDP is stateless, some of the options proposed herein may have similar benefit in being shared or cached. We call this UCB Sharing, or UDP Control Block Sharing, by analogy. Just as TCB sharing is not a standard because it is consistent with existing TCP specifications, UCB sharing would be consistent with existing UDP specifications, including this one. Both are implementation issues that are outside the scope of their respective specifications, and so UCB sharing is outside the scope of this document. Touch Expires September 1, 2022 [Page 29] Internet-Draft Transport Options for UDP March 2022 18. Updates to RFC 768 This document updates RFC 768 as follows: o This document defines the meaning of the IP payload area beyond the UDP length but within the IP length. o This document extends the UDP API to support the use of options. 19. Interactions with other RFCs (and drafts) This document clarifies the interaction between UDP length and IP length that is not explicitly constrained in either UDP or the host requirements [RFC768] [RFC1122]. Teredo extensions (TE) define use of a similar surplus area for trailers [RFC6081]. TE defines the UDP length pointing beyond (larger) than the location indicated by the IP length rather than shorter (as used herein): "..the IPv6 packet length (i.e., the Payload Length value in the IPv6 header plus the IPv6 header size) is less than or equal to the UDP payload length (i.e., the Length value in the UDP header minus the UDP header size)" As a result, UDP options are not compatible with TE, but that is also why this document does not update TE. Additionally, it is not at all clear how TE operates, as it requires network processing of the UDP length field to understand the total message including TE trailers. TE updates Teredo NAT traversal [RFC4380]. The NAT traversal document defined "consistency" of UDP length and IP length as: "An IPv6 packet is deemed valid if it conforms to [RFC2460]: the protocol identifier should indicate an IPv6 packet and the payload length should be consistent with the length of the UDP datagram in which the packet is encapsulated." IPv6 is clear on the meaning of this consistency, in which the pseudoheader used for UDP checksums is based on the UDP length, not inferred from the IP length, using the same text in the current specification [RFC8200]: "The Upper-Layer Packet Length in the pseudo-header is the length of the upper-layer header and data (e.g., TCP header plus TCP data). Some upper-layer protocols carry their own Touch Expires September 1, 2022 [Page 30] Internet-Draft Transport Options for UDP March 2022 length information (e.g., the Length field in the UDP header); for such protocols, that is the length used in the pseudo- header." This document is consistent the UDP profile for Robust Header Compression (ROHC)[RFC3095], noted here: "The Length field of the UDP header MUST match the Length field(s) of the preceding subheaders, i.e., there must not be any padding after the UDP payload that is covered by the IP Length." ROHC compresses UDP headers only when this match succeeds. It does not prohibit UDP headers where the match fails; in those cases, ROHC default rules (Section 5.10) would cause the UDP header to remain uncompressed. Upon receipt of a compressed UDP header, Section A.1.3 of that document indicates that the UDP length is "INFERRED"; in uncompressed packets, it would simply be explicitly provided. This issue of handling UDP header compression is more explicitly described in more recent specifications, e.g., Sec. 10.10 of Static Context Header Compression [RFC8724]. 20. Multicast Considerations UDP options are primarily intended for unicast use. Using these options over multicast IP requires careful consideration, e.g., to ensure that the options used are safe for different endpoints to interpret differently (e.g., either to support or silently ignore) or to ensure that all receivers of a multicast group confirm support for the options in use. 21. Security Considerations There are a number of security issues raised by the introduction of options to UDP. Some are specific to this variant, but others are associated with any packet processing mechanism; all are discussed in this section further. The use of UDP packets with inconsistent IP and UDP Length fields has the potential to trigger a buffer overflow error if not properly handled, e.g., if space is allocated based on the smaller field and copying is based on the larger. However, there have been no reports of such vulnerability and it would rely on inconsistent use of the two fields for memory allocation and copying. Touch Expires September 1, 2022 [Page 31] Internet-Draft Transport Options for UDP March 2022 UDP options are not covered by DTLS (datagram transport-layer security). Despite the name, neither TLS [RFC8446] (transport layer security, for TCP) nor DTLS [RFC6347] (TLS for UDP) protect the transport layer. Both operate as a shim layer solely on the payload of transport packets, protecting only their contents. Just as TLS does not protect the TCP header or its options, DTLS does not protect the UDP header or the new options introduced by this document. Transport security is provided in TCP by the TCP Authentication Option (TCP-AO [RFC5925]) or in UDP by the Authentication (AUTH) option (Section 8.9) and UNSAFE Encryption (ENCR) option (9). Transport headers are also protected as payload when using IP security (IPsec) [RFC4301]. UDP options use the TLV syntax similar to that of TCP. This syntax is known to require serial processing and may pose a DOS risk, e.g., if an attacker adds large numbers of unknown options that must be parsed in their entirety. Implementations concerned with the potential for this vulnerability MAY implement only the required options and MAY also limit processing of TLVs, either in number of options or total length, or both. Because required options come first and at most once each (with the exception of NOPs, which should never need to come in sequences of more than seven in a row), this limits their DOS impact. Note that TLV formats for options does require serial processing, but any format that allows future options, whether ignored or not, could introduce a similar DOS vulnerability. UDP security should never rely solely on transport layer processing of options. UNSAFE options are the only type that share fate with the UDP data, because of the way that data is hidden in the surplus area until after those options are processed. All other options default to being silently ignored at the transport layer but may be dropped either if that default is overridden (e.g., by configuration) or discarded at the application layer (e.g., using information about the options processed that are passed along with the packet). UDP fragmentation introduces its own set of security concerns, which can be handled in a manner similar to IP reassembly or TCP segment reordering [CERT18]. In particular, the number of packets pending reassembly and effort used for reassembly is typically limited. In addition, it may be useful to assume a reasonable minimum fragment size, e.g., that non-terminal fragments should never be smaller than 500 bytes. Touch Expires September 1, 2022 [Page 32] Internet-Draft Transport Options for UDP March 2022 22. IANA Considerations Upon publication, IANA is hereby requested to create a new registry for UDP Option Kind numbers, similar to that for TCP Option Kinds. Initial values of this registry are as listed in Section 7. Additional values in this registry are to be assigned from the UNASSIGNED values in Section 7 by IESG Approval or Standards Action [RFC8126]. Those assignments are subject to the conditions set forth in this document, particularly (but not limited to) those in Section 10. Although option nicknames are not used in-band, IANA should require UNSAFE safe option values to commence with the letter "U" and avoid that letter as commencing safe options. Upon publication, IANA is hereby requested to create a new registry for UDP Experimental Option Experiment Identifiers (UDP ExIDs) for use in a similar manner as TCP ExIDs [RFC6994]. UDP ExIDs can be used in either (or both) the EXP or UEXP options. This registry is initially empty. Values in this registry are to be assigned by IANA using first-come, first-served (FCFS) rules [RFC8126]. Options using these ExIDs are subject to the same conditions as new options, i.e., they too are subject to the conditions set forth in this document, particularly (but not limited to) those in Section 10. 23. References 23.1. Normative References [Fa22] Fairhurst, G., T. Jones, "Datagram PLPMTUD for UDP Options," draft-ietf-tsvwg-udp-options-dplpmtud, Feb. 2022. [RFC768] Postel, J., "User Datagram Protocol," RFC 768, August 1980. [RFC791] Postel, J., "Internet Protocol," RFC 791, Sept. 1981. [RFC1122] Braden, R., Ed., "Requirements for Internet Hosts -- Communication Layers," RFC 1122, Oct. 1989. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels," BCP 14, RFC 2119, March 1997. [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words," RFC 2119, May 2017. Touch Expires September 1, 2022 [Page 33] Internet-Draft Transport Options for UDP March 2022 23.2. Informative References [Fa18] Fairhurst, G., T. Jones, R. Zullo, "Checksum Compensation Options for UDP Options", draft-fairhurst-udp-options-cco, Oct. 2018. [Hi15] Hildebrand, J., B. Trammel, "Substrate Protocol for User Datagrams (SPUD) Prototype," draft-hildebrand-spud- prototype-03, Mar. 2015. [RFC793] Postel, J., "Transmission Control Protocol" RFC 793, September 1981. [RFC1071] Braden, R., D. Borman, C. Partridge, "Computing the Internet Checksum," RFC 1071, Sept. 1988. [RFC1191] Mogul, J., S. Deering, "Path MTU discovery," RFC 1191, November 1990. [RFC2923] Lahey, K., "TCP Problems with Path MTU Discovery," RFC 2923, September 2000. [RFC3095] Bormann, C. (Ed), et al., "RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP, ESP, and uncompressed," RFC 3095, July 2001. [RFC3385] Sheinwald, D., J. Satran, P. Thaler, V. Cavanna, "Internet Protocol Small Computer System Interface (iSCSI) Cyclic Redundancy Check (CRC)/Checksum Considerations," RFC 3385, Sep. 2002. [RFC3692] Narten, T., "Assigning Experimental and Testing Numbers Considered Useful," RFC 3692, Jan. 2004. [RFC3828] Larzon, L-A., M. Degermark, S. Pink, L-E. Jonsson (Ed.), G. Fairhurst (Ed.), "The Lightweight User Datagram Protocol (UDP-Lite)," RFC 3828, July 2004. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, Dec. 2005. [RFC4340] Kohler, E., M. Handley, and S. Floyd, "Datagram Congestion Control Protocol (DCCP)", RFC 4340, March 2006. [RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through Network Address Translations (NATs)," RFC 4380, Feb. 2006. Touch Expires September 1, 2022 [Page 34] Internet-Draft Transport Options for UDP March 2022 [RFC4960] Stewart, R. (Ed.), "Stream Control Transmission Protocol", RFC 4960, September 2007. [RFC5925] Touch, J., A. Mankin, R. Bonica, "The TCP Authentication Option," RFC 5925, June 2010. [RFC6081] Thaler, D., "Teredo Extensions," RFC 6081, Jan 2011. [RFC6347] Rescorla, E., N. Modadugu, "Datagram Transport Layer Security Version 1.2," RFC 6347, Jan. 2012. [RFC6691] Borman, D., "TCP Options and Maximum Segment Size (MSS)," RFC 6691, July 2012. [RFC6935] Eubanks, M., P. Chimento, M. Westerlund, "IPv6 and UDP Checksums for Tunneled Packets," RFC 6935, April 2013. [RFC6978] Touch, J., "A TCP Authentication Option Extension for NAT Traversal", RFC 6978, July 2013. [RFC6994] Touch, J., "Shared Use of Experimental TCP Options," RFC 6994, Aug. 2013. [RFC7323] Borman, D., R. Braden, V. Jacobson, R. Scheffenegger (Ed.), "TCP Extensions for High Performance," RFC 7323, Sep. 2014. [RFC8085] Eggert, L., G. Fairhurst, G. Shepherd, "UDP Usage Guidelines," RFC 8085, Feb. 2017. [RFC8126] Cotton, M., B. Leiba, T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs," RFC 8126, June 2017. [RFC8200] Deering, S., R. Hinden, "Internet Protocol Version 6 (IPv6) Specification," RFC 8200, Jul. 2017. [RFC8201] McCann, J., S. Deering, J. Mogul, R. Hinden (Ed.), "Path MTU Discovery for IP version 6," RFC 8201, Jul. 2017. [RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3," RFC 8446, Aug. 2018. [RFC8724] Minaburo, A., L. Toutain, C. Gomez, D. Barthel, JC., "SCHC: Generic Framework for Static Context Header Compression and Fragmentation," RFC 8724, Apr. 2020. Touch Expires September 1, 2022 [Page 35] Internet-Draft Transport Options for UDP March 2022 [RFC8899] Fairhurst, G., T. Jones, M. Tuxen, I. Rungeler, T. Volker, "Packetization Layer Path MTU Discovery for Datagram Transports," RFC 8899, Sep. 2020. [RFC9040] Touch, J., M. Welzl, S. Islam, "TCP Control Block Interdependence," RFC 9040, Jul. 2021. [RFC9187] Touch, J., "Sequence Number Extension for Windowed Protocols," RFC 9187, Jan. 2022. [CERT18] CERT Coordination Center, "TCP implementations vulnerable to Denial of Service,", Vulnerability Note VU 962459, Software Engineering Institute, CMU, 2018, https://www.kb.cert.org/vuls/id/962459. [To18] Touch, J., "A TCP Authentication Option Extension for Payload Encryption," draft-touch-tcp-ao-encrypt, Jul. 2018. 24. Acknowledgments This work benefitted from feedback from Bob Briscoe, Ken Calvert, Ted Faber, Gorry Fairhurst (including OCS for misbehaving middlebox traversal), C. M. Heard (including combining previous FRAG and LITE options into the new FRAG), Tom Herbert, Mark Smith, and Raffaele Zullo, as well as discussions on the IETF TSVWG and SPUD email lists. This work was partly supported by USC/ISI's Postel Center. This document was prepared using 2-Word-v2.0.template.dot. Authors' Addresses Joe Touch Manhattan Beach, CA 90266 USA Phone: +1 (310) 560-0334 Email: touch@strayalpha.com Touch Expires September 1, 2022 [Page 36] Internet-Draft Transport Options for UDP March 2022 Appendix A.Implementation Information The following information is provided to encourage interoperable API implementations. System-level variables (sysctl): Name default meaning ---------------------------------------------------- net.ipv4.udp_opt 0 UDP options available net.ipv4.udp_opt_ocs 1 Default use OCS net.ipv4.udp_opt_apc 0 Default include APC net.ipv4.udp_opt_frag 0 Default fragment net.ipv4.udp_opt_mss 0 Default include MSS net.ipv4.udp_opt_mrss 0 Default include MRSS net.ipv4.udp_opt_req 0 Default include REQ net.ipv4.udp_opt_resp 0 Default include RES net.ipv4.udp_opt_time 0 Default include TIME net.ipv4.udp_opt_auth 0 Default include AUTH net.ipv4.udp_opt_exp 0 Default include EXP net.ipv4.udp_opt_uenc 0 Default include UENC net.ipv4.udp_opt_uexp 0 Default include UEXP Socket options (sockopt), cached for outgoing datagrams: Name meaning ---------------------------------------------------- UDP_OPT Enable UDP options (at all) UDP_OPT_OCS Use UDP OCS UDP_OPT_APC Enable UDP APC option UDP_OPT_FRAG Enable UDP fragmentation UDP OPT MSS Enable UDP MSS option UDP OPT MRSS Enable UDP MRSS option UDP OPT REQ Enable UDP REQ option UDP OPT RES Enable UDP RES option UDP_OPT_TIME Enable UDP TIME option UDP OPT AUTH Enable UDP AUTH option UDP OPT EXP Enable UDP EXP option UDP_OPT_UENC Enable UDP UENC option UDP OPT UEXP Enable UDP UEXP option Send/sendto parameters: Connection parameters (per-socketpair cached state, part UCB): Touch Expires September 1, 2022 [Page 37] Internet-Draft Transport Options for UDP March 2022 Name Initial value ---------------------------------------------------- opts_enabled net.ipv4.udp_opt ocs_enabled net.ipv4.udp_opt_ocs The following option is included for debugging purposes, and MUST NOT be enabled otherwise. System variables net.ipv4.udp_opt_junk 0 Touch Expires September 1, 2022 [Page 38] Internet-Draft Transport Options for UDP March 2022 System-level variables (sysctl): Name default meaning ---------------------------------------------------- net.ipv4.udp_opt_junk 0 Default use of junk Socket options (sockopt): Name params meaning ------------------------------------------------------ UDP_JUNK - Enable UDP junk option UDP_JUNK_VAL fillval Value to use as junk fill UDP_JUNK_LEN length Length of junk payload in bytes Connection parameters (per-socketpair cached state, part UCB): Name Initial value ---------------------------------------------------- junk_enabled net.ipv4.udp_opt_junk junk_value 0xABCD junk_len 4 Touch Expires September 1, 2022 [Page 39]