SR Replication Segment for Multi-point Service Delivery

2.1. SR-MPLS data plane

When the Active Segment is a Replication SID, the processing results in a POP operation and lookup of the associated Replication state. For each replication in the Replication state, the operation is a PUSH of the downstream Replication SID and an optional segment list on to the packet which is forwarded to the Downstream node. For leaf nodes the inner packet is forwarded as per local configuration.¶

When the root of a multi-point service steers a packet to a Replication segment, it results in a replication to each Downstream node in the associated replication state. The operation is a PUSH of the replication SID and an optional segment list on to the packet which is forwarded to the downstream node.¶

2.2. SRv6 data plane

In SRv6 [RFC8986], the "Endpoint with replication" behavior (End.Replicate for short) replicates a packet and forwards the packet according to a Replication state.¶

When processing a packet destined to a local Replication-SID, the packet is replicated to Downstream nodes in the associated Replication state. For replication, the outer header is re-used, and the Downstream Replication SID is written into the outer IPv6 header destination address.If required, an optional segment list is used to encapsulate the replicated packet via H.Encaps. For a leaf node, the packet is decapsulated and the inner packet is forwarded as per local configuration.¶

When the root of a multi-point service steers a packet into a Replication segment, for each replication, H.Encaps is used to encapsulate the packet with the segment list to the Downstream node .¶

An End.Replicate SID MUST only appear as the ultimate SID in a SID-list. An implementation that receives a packet destined to a locally instantiated End.Replicate SID that is not the ultimate segment SHOULD reply with ICMP Parameter Problem error (Erroneous header field encountered) and discard the packet.¶

8.1. Normative References

[I-D.ietf-spring-segment-routing-policy]

Filsfils, C., Talaulikar, K., Voyer, D., Bogdanov, A., and P. Mattes, "Segment Routing Policy Architecture", Work in Progress, Internet-Draft, draft-ietf-spring-segment-routing-policy-13, 28 May 2021, <https://www.ietf.org/archive/id/draft-ietf-spring-segment-routing-policy-13.txt>.

[RFC2119]

Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, <https://www.rfc-editor.org/info/rfc2119>.

[RFC8402]

Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L., Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing Architecture", RFC 8402, DOI 10.17487/RFC8402, July 2018, <https://www.rfc-editor.org/info/rfc8402>.

[RFC8986]

Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer, D., Matsushima, S., and Z. Li, "Segment Routing over IPv6 (SRv6) Network Programming", RFC 8986, DOI 10.17487/RFC8986, February 2021, <https://www.rfc-editor.org/info/rfc8986>.

8.2. Informative References

[I-D.filsfils-spring-srv6-net-pgm-illustration]

Filsfils, C., Garvia, P. C., Li, Z., Matsushima, S., Decraene, B., Steinberg, D., Lebrun, D., Raszuk, R., and J. Leddy, "Illustrations for SRv6 Network Programming", Work in Progress, Internet-Draft, draft-filsfils-spring-srv6-net-pgm-illustration-04, 30 March 2021, <https://www.ietf.org/archive/id/draft-filsfils-spring-srv6-net-pgm-illustration-04.txt>.

[I-D.ietf-lsr-flex-algo]

Psenak, P., Hegde, S., Filsfils, C., Talaulikar, K., and A. Gulko, "IGP Flexible Algorithm", Work in Progress, Internet-Draft, draft-ietf-lsr-flex-algo-17, 6 July 2021, <https://www.ietf.org/archive/id/draft-ietf-lsr-flex-algo-17.txt>.

[I-D.ietf-pim-sr-p2mp-policy]

Voyer, D., Filsfils, C., Parekh, R., Bidgoli, H., and Z. Zhang, "Segment Routing Point-to-Multipoint Policy", Work in Progress, Internet-Draft, draft-ietf-pim-sr-p2mp-policy-02, 19 February 2021, <https://www.ietf.org/archive/id/draft-ietf-pim-sr-p2mp-policy-02.txt>.

[RFC6513]

Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February 2012, <https://www.rfc-editor.org/info/rfc6513>.

[RFC7432]

Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A., Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February 2015, <https://www.rfc-editor.org/info/rfc7432>.

[RFC7988]

Rosen, E., Ed., Subramanian, K., and Z. Zhang, "Ingress Replication Tunnels in Multicast VPN", RFC 7988, DOI 10.17487/RFC7988, October 2016, <https://www.rfc-editor.org/info/rfc7988>.

A.1. SR-MPLS

In this example, the Node-SID of a node Rn is N-SIDn and Adjacency-SID from node Rm to node Rn is A-SIDmn. Interface between Rm and Rn is Lmn.¶

Assume a Replication segment identified with R-ID at Replication Node R1 and downstream Nodes R2, R6 and R7. The Replication SID at node n is R-SIDn. A packet replicated from R1 to R7 has to traverse R4.¶

The Replication segment state at nodes R1, R2, R6 and R7 is shown below. Note nodes R3, R4 and R5 do not have state for the Replication segment.¶

Replication segment at R1:¶

Replication segment <R-ID,R1>:
 Replication SID: R-SID1
 Replication State:
   R2: <R-SID2->L12>
   R6: <N-SID6, R-SID6>
   R7: <N-SID4, A-SID47, R-SID7>

Replication to R2 steers packet directly to R2 on interface L12. Replication to R6, using N-SID6, steers packet via IGP shortest path to that node. Replication to R7 is steered via R4, using N-SID4 and then adjacency SID A-sID47 to R7.¶

Replication segment at R2:¶

Replication segment <R-ID,R2>:
 Replication SID: R-SID2
 Replication State:
   R2: <Leaf>

Replication segment at R6:¶

Replication segment <R-ID,R6>:
 Replication SID: R-SID6
 Replication State:
   R6: <Leaf>

Replication segment at R7:¶

Replication segment <R-ID,R7>:
 Replication SID: R-SID7
 Replication State:
   R7: <Leaf>

When a packet is steered into the Replication segment at R1:¶

• Since R1 is directly connected to R2, R1 performs PUSH operation with just <R-SID2> label for the replicated copy and sends it to R2 on interface L12. R2, as Leaf, performs NEXT operation, pops R-SID2 label and delivers the payload.¶
• R1 performs PUSH operation with <N-SID6, R-SID6> label stack for the replicated copy to R6 and sends it to R2, the nexthop on IGP shortest path to R6. R2 performs CONTINUE operation on N-SID6 and forwards it to R3. R3 is the penultimate hop for N-SID6; it performs penultimate hop popping, which corresponds to the NEXT operation and the packet is then sent to R6 with <R-SID6> in the label stack. R6, as Leaf, performs NEXT operation, pops R-SID6 label and delivers the payload.¶
• R1 performs PUSH operation with <N-SID4, A-SID47, R-SID7> label stack for the replicated copy to R7 and sends it to R2, the nexthop on IGP shortest path to R4. R2 is the penultimate hop for N-SID4; it performs penultimate hop popping, which corresponds to the NEXT operation and the packet is then sent to R4 with <A-SID47, R-SID1> in the label stack. R4 performs NEXT operation, pops A-SID47, and delivers packet to R7 with <R-SID7> in the label stack. R7, as Leaf, performs NEXT operation, pops R-SID7 label and delivers the payload.¶

A.2. SRv6

For SRv6 , we use SID allocation scheme, reproduced below, from Illustrations for SRv6 Network Programming [I-D.filsfils-spring-srv6-net-pgm-illustration]¶

• 2001:db8::/32 is an IPv6 block allocated by a RIR to the operator¶
• 2001:db8:0::/48 is dedicated to the internal address space¶
• 2001:db8:cccc::/48 is dedicated to the internal SRv6 SID space¶
• We assume a location expressed in 64 bits and a function expressed in 16 bits¶
• Node k has a classic IPv6 loopback address 2001:db8::k/128 which is advertised in the IGP¶
• Node k has 2001:db8:cccc:k::/64 for its local SID space. Its SIDs will be explicitly assigned from that block¶
• Node k advertises 2001:db8:cccc:k::/64 in its IGP¶
• Function :1:: (function 1, for short) represents the End function with PSP support¶
• Function :Cn:: (function Cn, for short) represents the End.X function from to Node n¶

Each node k has:¶

• An explicit SID instantiation 2001:db8:cccc:k:1::/128 bound to an End function with additional support for PSP¶
• An explicit SID instantiation 2001:db8:cccc:k:Cj::/128 bound to an End.X function to neighbor J with additional support for PSP¶
• An explicit SID instantiation 2001:db8:cccc:k:Fk::/128 bound to an End.Replcate function¶

Assume a Replication segment identified with R-ID at Replication Node R1 and downstream Nodes R2, R6 and R7. The Replication SID at node k, bound to an End.Replcate function, is 2001:db8:cccc:k:Fk::/128. A packet replicated from R1 to R7 has to traverse R4.¶

The Replication segment state at nodes R1, R2, R6 and R7 is shown below. Note nodes R3, R4 and R5 do not have state for the Replication segment.¶

Replication segment at R1:¶

Replication segment <R-ID,R1>:
 Replication SID: 2001:db8:cccc:1:F1::0
 Replication State:
   R2: <2001:db8:cccc:2:F2::0->L12>
   R6: <2001:db8:cccc:6:F6::0>
   R7: <2001:db8:cccc:4:C7::0, 2001:db8:cccc:7:F7::0>

Replication to R2 steers packet directly to R2 on interface L12. Replication to R6, using 2001:db8:cccc:6:F6::0, steers packet via IGP shortest path to that node. Replication to R7 is steered via R4, using End.X SID 2001:db8:cccc:4:C7::0 at R4 to R7.¶

Replication segment at R2:¶

Replication segment <R-ID,R2>:
 Replication SID: 2001:db8:cccc:2:F2::0
 Replication State:
   R2: <Leaf>

Replication segment at R6:¶

Replication segment <R-ID,R6>:
 Replication SID: 2001:db8:cccc:6:F6::0
 Replication State:
   R6: <Leaf>

Replication segment at R7:¶

Replication segment <R-ID,R7>:
 Replication SID: 2001:db8:cccc:7:F7::0
 Replication State:
   R7: <Leaf>

When a packet, (A,B2), is steered into the Replication segment at R1:¶

• Since R1 is directly connected to R2, R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:2:F2::0) (A, B2), and sends it to R2 on interface L12. R2, as Leaf, removes outer IPv6 header and delivers the payload.¶
• R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:6:F6::0) (A, B2) then forwards the resulting packet on the shortest path to 2001:db8:cccc:6::/64. R2 and R3 forward the packet using 2001:db8:cccc:6::/64. R6, as Leaf, removes outer IPv6 header and delivers the payload.¶
• R1 creates encapsulated replicated copy (2001:db8::1, 2001:db8:cccc:4:C7::0) (2001:db8:cccc:7:F7::0; SL=1) (A, B2) and sends it to R2, the nexthop on IGP shortest path to 2001:db8:cccc:4::/64. R2 forwards packet to R4 using 2001:db8:cccc:4::/64. R4 executes End.X function on 2001:db8:cccc:4:C7::0, performs PSP action, removes SRH and sends resulting packet (2001:db8::1, 2001:db8:cccc:7:F7::0) (A, B2) to R7. R7, as Leaf, removes outer IPv6 header and delivers the payload.¶