Network Working Group L. Berger
Internet-Draft LabN Consulting, L.L.C.
Intended status: Standards Track C. Hopps
Expires: May 1, 2017 Deutsche Telekom
A. Lindem
Cisco Systems
D. Bogdanovic
October 28, 2016

YANG Network Instances
draft-ietf-rtgwg-ni-model-01

Abstract

This document defines a network instance module. This module along with the logical network element module can be used to manage the logical and virtual resource representations that may be present on a network device. Examples of common industry terms for logical resource representations are Logical Systems or Logical Routers. Examples of common industry terms for virtual resource representations are Virtual Routing and Forwarding (VRF) instances and Virtual Switch Instances (VSIs).

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on May 1, 2017.

Copyright Notice

Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This document defines the second of two new modules that are defined to support the configuration and operation of network-devices that allow for the partitioning of resources from both, or either, management and networking perspectives. Both make use of the YANG functionality enabled by YANG Schema Mount [I-D.ietf-netmod-schema-mount].

Two forms of resource partitioning are supported:

The first form, which is defined in [I-D.ietf-rtgwg-lne-model], provides a logical partitioning of a network device where each partition is separately managed as essentially an independent network element which is 'hosted' by the base network device. These hosted network elements are referred to as logical network elements, or LNEs, and are supported by the logical-network-element module defined in [I-D.ietf-rtgwg-lne-model]. The module is used to identify LNEs and associate resources from the network-device with each LNE. LNEs themselves are represented in YANG as independent network devices; each accessed independently. Optionally, and when supported by the implementation, they may also be accessed from the host system. Examples of vendor terminology for an LNE include logical system or logical router, and virtual switch, chassis, or fabric.

The second form, which is defined in this document, provides support what is commonly referred to as Virtual Routing and Forwarding (VRF) instances as well as Virtual Switch Instances (VSI), see [RFC4026]. In this form of resource partitioning multiple control plane and forwarding/bridging instances are provided by and managed via a single (physical or logical) network device. This form of resource partitioning is referred to as Network Instances and are supported by the network-instance module defined below. Configuration and operation of each network-instance is always via the network device and the network-instance module.

This document was motivated by, and derived from, [I-D.ietf-rtgwg-device-model].

1.1. Status of Work and Open Issues

The top open issues are:

  1. This document will need to match the evolution and standardization of [I-D.openconfig-netmod-opstate] or [I-D.ietf-netmod-opstate-reqs] by the Netmod WG.

2. Overview

In this document, we consider network devices that support protocols and functions defined within the IETF Routing Area, e.g, routers, firewalls and hosts. Such devices may be physical or virtual, e.g., a classic router with custom hardware or one residing within a server-based virtual machine implementing a virtual network function (VNF). Each device may sub-divide their resources into logical network elements (LNEs) each of which provides a managed logical device. Examples of vendor terminology for an LNE include logical system or logical router, and virtual switch, chassis, or fabric. Each LNE may also support virtual routing and forwarding (VRF) and virtual switching instance (VSI) functions, which are referred to below as a network instances (NIs). This breakdown is represented in Figure 1.


           ,''''''''''''''''''''''''''''''''''''''''''''''`.
           |      Network Device (Physical or Virtual)     |
           | .....................   ..................... |
           | :  Logical Network  :   :  Logical Network  : |
           | :      Element      :   :      Element      : |
           | :+-----+-----+-----+:   :+-----+-----+-----+: |
           | :| Net | Net | Net |:   :| Net | Net | Net |: |
           | :|Inst.|Inst.|Inst.|:   :|Inst.|Inst.|Inst.|: |
           | :+-----+-----+-----+:   :+-----+-----+-----+: |
           | :  | |   | |   | |  :   :  | |   | |   | |  : |
           | :..|.|...|.|...|.|..:   :..|.|...|.|...|.|..: |
           |    | |   | |   | |         | |   | |   | |    |
            `'''|'|'''|'|'''|'|'''''''''|'|'''|'|'''|'|'''''
                | |   | |   | |         | |   | |   | |
                   Interfaces              Interfaces

Figure 1: Module Element Relationships

A model for LNEs is described in [I-D.ietf-rtgwg-lne-model] and the model for network instances is covered in Section 3. For more information on how these models may be used within an overall device model structure, see [I-D.ietf-rtgwg-device-model].

The interface management model [RFC7223] is an existing model that is impacted by the definition of LNEs and network instances. This document and [I-D.ietf-rtgwg-lne-model] define augmentations to the interface module to support LNEs and NIs. Similar elements, although perhaps only for LNEs, may also need to be included as part of the definition of the future hardware and QoS modules.

Interfaces are a crucial part of any network device's configuration and operational state. They generally include a combination of raw physical interfaces, link-layer interfaces, addressing configuration, and logical interfaces that may not be tied to any physical interface. Several system services, and layer 2 and layer 3 protocols may also associate configuration or operational state data with different types of interfaces (these relationships are not shown for simplicity). The interface management model is defined by [RFC7223].

The logical-network-element and network-instance modules augment the existing interface management model in two ways: The first, by the logical-network-element module, adds an identifier which is used on physical interface types to identify an associated LNE. The second, by the network-instance module, adds a name which is used on interface or sub-interface types to identify an associated network instance. Similarly, this name is also added for IPv4 and IPv6 types, as defined in [RFC7277].

    module: ietf-logical-network-element
    augment /if:interfaces/if:interface:
       +--rw bind-lne-name?   string

    module: ietf-network-instance
    augment /if:interfaces/if:interface:
       +--rw bind-network-instance-name?   string
    augment /if:interfaces/if:interface/ip:ipv4:
       +--rw bind-network-instance-name?   string
    augment /if:interfaces/if:interface/ip:ipv6:
       +--rw bind-network-instance-name?   string

The interface related augmentations are as follows:

The following is an example of envisioned combined usage. The interfaces container includes a number of commonly used components as examples:

          +--rw if:interfaces
          |  +--rw interface* [name]
          |     +--rw name                       string
          |     +--rw bind-lne-name?             string
          |     +--rw ethernet
          |     |  +--rw ni:bind-network-instance-name? string
          |     |  +--rw aggregates
          |     |  +--rw rstp
          |     |  +--rw lldp
          |     |  +--rw ptp
          |     +--rw vlans
          |     +--rw tunnels
          |     +--rw ipv4
          |     |  +--rw ni:bind-network-instance-name? string
          |     |  +--rw arp
          |     |  +--rw icmp
          |     |  +--rw vrrp
          |     |  +--rw dhcp-client
          |     +--rw ipv6
          |        +--rw ni:bind-network-instance-name? string
          |        +--rw vrrp
          |        +--rw icmpv6
          |        +--rw nd
          |        +--rw dhcpv6-client

The [RFC7223] defined interface model is structured to include all interfaces in a flat list, without regard to logical or virtual instances (e.g., VRFs) supported on the device. The bind-lne-name and bind-network-instance-name leaves provide the association between an interface and its associated LNE and NI (e.g., VRF or VSI).

3. Network Instances

The network instance container is used to represent virtual routing and forwarding instances (VRFs) and virtual switching instances (VSIs), [RFC4026]. VRFs and VSIs are commonly used to isolate routing and switching domains, for example to create virtual private networks, each with their own active protocols and routing/switching policies. The model represents both core/provider and virtual instances. Network instances reuse and build on [I-D.ietf-netmod-routing-cfg] and are shown below:

    module: ietf-network-instance
       +--rw network-instances
          +--rw network-instance* [name]
             +--rw name                         string
             +--rw type?                        identityref
             +--rw enabled?                     boolean
             +--rw description?                 string
             +--rw network-instance-policy
             |  ...
             +--rw root?                      yang-schema-mount
             |  ...
    augment /if:interfaces/if:interface:
       +--rw bind-network-instance-name?   string
    augment /if:interfaces/if:interface/ip:ipv4:
       +--rw bind-network-instance-name?   string
    augment /if:interfaces/if:interface/ip:ipv6:
       +--rw bind-network-instance-name?   string

A network instance is identified by a `name` string. This string is used both as an index within the network-instance module and to associate resources with a network instance as shown above in the interface augmentation. Type is used to indicate the type NI, such as L3-VRF, VPLS, L2-VSI, etc. Network instance policy and root are discussed in greater detail below.

3.1. Network Instance Policy

Network instance policies are used to control how NI information is represented at the device level, VRF routing policies, and VRF/VSI identifiers. Examples include BGP route targets (RTs) and route distinguishers (RDs), virtual network identifiers (VN-IDs), VPLS neighbors, etc. The structure is expected to be:

    module: ietf-network-instance
       +--rw network-instances
          +--rw network-instance* [name]
             +--rw network-instance-policy
                (TBD)

3.2. Network Instance Management

Modules that may be used to represent network instance specific information will be available under `root`. As with LNEs, actual module availability is expected to be implementation dependent. The yang library module [RFC7895] is expected to be the primary method used to identify supported modules. Resource related control and assignment is expected to be managed at the network-device level, not the network instance level, based on the `bind-network-instance-name` augmentation mentioned above.

As an example, consider the case where a network instance with a `name` of "green" is defined on a network device. In this case the following structure might be made available:

   +--rw yanglib:modules-state           [RFC7895]
   +--rw if:interfaces                   [RFC7223]
   |  +--rw bind-network-instance-name="green" string
   +--rw network-instances
      +--rw network-instance* [name]
         +--rw name="green"    string
         +--rw type?                           identityref
         +--rw enabled=true                    boolean
         +--rw description="The Green VRF"     string
         +--rw network-instance-policy
         |  ... (RT=1000:1, RD=1.2.3.4)
         +--rw root?                           yang-schema-mount
            +--rw yanglib:modules-state  [RFC7895]
            +--rw if:intefaces           [RFC7223]
            +--rw mm:network-services
            +--rw nn:oam-protocols
            +--rw oo:routing
            +--rw pp:mpls

All modules that represent control-plane and data-plane information may be present at the `root`, and be accessible via paths modified per [I-D.ietf-netmod-schema-mount]. The list of available modules is expected to be implementation dependent. As is the method used by an implementation to support NIs.

3.3. Network Instance Instantiation

Network instances may be controlled by clients using existing list operations. When list entries are created, a new instance is instantiated. The models mounted under a NI root is expected to be dependent on the server implementation. When a list entry is deleted, an existing network instance is destroyed. For more information see [RFC7950] Section 7.8.6.

4. Security Considerations

TBD

5. IANA Considerations

This document registers a URI in the IETF XML registry [RFC3688]. Following the format in RFC 3688, the following registration is requested to be made.

     URI: urn:ietf:params:xml:ns:yang:ietf-network-instance

     Registrant Contact: The IESG.

     XML: N/A, the requested URI is an XML namespace.
     

This document registers a YANG module in the YANG Module Names registry [RFC6020].

  name:        ietf-network-instance
  namespace:   urn:ietf:params:xml:ns:yang:ietf-network-instance
  prefix:      ni
  reference:   RFC XXXX
  

6. Network Instance Model

The structure of the model defined in this document is described by the YANG module below.

<CODE BEGINS> file "ietf-network-instance@2016-10-27.yang"
module ietf-network-instance {

  yang-version 1.1;

  // namespace
  namespace "urn:ietf:params:xml:ns:yang:ietf-network-instance";

  prefix ni;

  // import some basic types
  import ietf-interfaces {
    prefix if;
  }

  import ietf-ip {
    prefix ip;
  }

  import ietf-yang-schema-mount {
    prefix yangmnt;
  }

// meta
  organization "IETF Routing Area Working Group (rtgwg)";

  contact
      "Routing Area Working Group - <rtgwg@ietf.org>";

  description
    "This module is used to support multiple network instances
     within a single physical or virtual device.  Network
     instances are commonly know as VRFs (virtual routing
     and forwarding) and VSIs (virtual switching instances).";

  revision "2016-10-27" {
    description
      "Initial revision.";
    reference "RFC TBD";
  }

  // extension statements

  feature bind-network-instance-name {
    description
      "Network Instance to which an interface instance is bound";
  }

  // identity statements

  identity network-instance-type {
      description
         "Base identity from which identities describing
          network instance types are derived.";
  }

   identity ipv4-interface-protocol-type {
      description
          "Base identity for derivation of IPv4 interface
           protocols";
   }

   identity ipv6-interface-protocol-type {
      description
          "Base identity for derivation of IPv6 interface
           protocols";
   }

  // typedef statements

  // grouping statements

  grouping interface-ip-common {
    description
      "interface-specific configuration for IP interfaces, IPv4 and
      IPv6";

  }

  grouping ipv4-interface-protocols {
      container ipv4-interface-protocols {
          list ipv4-interface-protocol {
              key "type";
              leaf type {
                  type identityref {
                      base ipv4-interface-protocol-type;
                  }
                  mandatory true;
                  description
                      "ARP, ICMP, VRRP, DHCP Client, etc.";
              }
              description
                  "List of IPv4 protocols configured
                   on an interface";
          }
          description
              "Container for list of IPv4 protocols configured
                on an interface";
      }
      description
          "Grouping for IPv4 protocols configured on an interface";
  }

  grouping ipv6-interface-protocols {
      description
          "Grouping for IPv6 protocols configured on
           an interface.";
      container ipv6-interface-protocols {
          description
              "Container for list of IPv6 protocols configured
                on an interface.";
          list ipv6-interface-protocol {
              key "type";
              description
                  "List of IPv6 protocols configured
                   on an interface";
              leaf type {
                  type identityref {
                      base ipv6-interface-protocol-type;
                  }
                  mandatory true;
                  description
                      "ND, ICMPv6, VRRP, DHCPv6 Client, etc.";
              }
          }
      }
  }

  grouping network-instance-policy {
    description
        "Network instance policies such as route
         distinguisher, route targets, VPLS ID and neighbor,
         Ethernet ID, etc. ";
    reference
        "RFC 4364 - BGP/MPLS Virtual Private Networks (VPNs)
         RFC 6074 - Provisioning, Auto-Discovery, and Signaling
              in Layer 2 Virtual Private Networks (L2VPNs)
         RFC 7432 - BGP MPLS-Based Ethernet VPN";
    container network-instance-policy {
        description
          "Network Instance Policy -- details TBD, 
          perhaps based on BESS model";
    }
  }

  // top level device definition statements
  container network-instances {
      description "Network instances each of which have
                   an independent IP/IPv6 addressing space
                   and protocol instantiations. For layer 3,
                   this consistent with the routing-instance
                   definition in ietf-routing";
      reference "draft-ietf-netmod-routing-cfg";
      list network-instance {
          key name;
          description "List of network-instances";
          leaf name {
              type string;
              description "device scoped
                           identifier for the network
                           instance";
          }
          leaf type {
              type identityref {
                  base network-instance-type;
              }
              description
                  "The network instance type -- details TBD
                   Likely types include core, L3-VRF, VPLS,
                   L2-cross-connect, L2-VSI, etc.";
          }
          leaf enabled {
              type boolean;
              default "true";
              description
                "Flag indicating whether or not the network
                 instance is enabled.";
          }
          leaf description {
              type string;
              description
                "Description of the network instance
                and its intended purpose";
          }

          uses network-instance-policy;

          anydata root {
              yangmnt:mount-point root;
              description "Root for models supported per
                           network instance";
          }
      }
  }

  // augment statements

  augment "/if:interfaces/if:interface" {
    description
        "Add a node for the identification of the logical network
        instance (which is within the interface's identified logical
        network element) associated with the IP information
        configured on an interface";

    leaf bind-network-instance-name {
      type string;
      description
        "Network Instance to which an interface is bound";
    }
  }

  augment "/if:interfaces/if:interface/ip:ipv4" {
    description
        "Add a node for the identification of the logical
        network instance (which is within the interface's
        identified physical or virtual device) associated with
        the IP information configured on an interface";

    leaf bind-network-instance-name {
      type string;
      description
        "Network Instance to which IPv4 interface is bound";

    }
  }

  augment "/if:interfaces/if:interface/ip:ipv6" {
    description
        "Add a node for the identification of the logical
        network instance (which is within the interface's
        identified physical or virtual device) associated with
        the IP information configured on an interface";

    leaf bind-network-instance-name {
      type string;
      description
        "Network Instance to which IPv6 interface is bound";

    }
  }

  // rpc statements

  // notification statements

}
<CODE ENDS>

7. References

7.1. Normative References

[I-D.ietf-netmod-schema-mount] Bjorklund, M. and L. Lhotka, "YANG Schema Mount", Internet-Draft draft-ietf-netmod-schema-mount-02, July 2016.
[I-D.ietf-rtgwg-lne-model] Berger, L., Hopps, C., Lindem, A. and D. Bogdanovic, "Logical Network Element Model", Internet-Draft draft-ietf-rtgwg-lne-model-00, June 2016.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004.
[RFC6020] Bjorklund, M., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010.
[RFC7223] Bjorklund, M., "A YANG Data Model for Interface Management", RFC 7223, DOI 10.17487/RFC7223, May 2014.
[RFC7277] Bjorklund, M., "A YANG Data Model for IP Management", RFC 7277, DOI 10.17487/RFC7277, June 2014.

7.2. Informative References

[I-D.ietf-netmod-opstate-reqs] Watsen, K. and T. Nadeau, "Terminology and Requirements for Enhanced Handling of Operational State", Internet-Draft draft-ietf-netmod-opstate-reqs-04, January 2016.
[I-D.ietf-netmod-routing-cfg] Lhotka, L. and A. Lindem, "A YANG Data Model for Routing Management", Internet-Draft draft-ietf-netmod-routing-cfg-24, October 2016.
[I-D.ietf-rtgwg-device-model] Lindem, A., Berger, L., Bogdanovic, D. and C. Hopps, "Network Device YANG Organizational Models", Internet-Draft draft-ietf-rtgwg-device-model-00, August 2016.
[I-D.openconfig-netmod-opstate] Shakir, R., Shaikh, A. and M. Hines, "Consistent Modeling of Operational State Data in YANG", Internet-Draft draft-openconfig-netmod-opstate-01, July 2015.
[RFC4026] Andersson, L. and T. Madsen, "Provider Provisioned Virtual Private Network (VPN) Terminology", RFC 4026, DOI 10.17487/RFC4026, March 2005.
[RFC7895] Bierman, A., Bjorklund, M. and K. Watsen, "YANG Module Library", RFC 7895, DOI 10.17487/RFC7895, June 2016.
[RFC7950] Bjorklund, M., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016.

Appendix A. Acknowledgments

The Routing Area Yang Architecture design team members included Acee Lindem, Anees Shaikh, Christian Hopps, Dean Bogdanovic, Lou Berger, Qin Wu, Rob Shakir, Stephane Litkowski, and Yan Gang.

The RFC text was produced using Marshall Rose's xml2rfc tool.




































































































Appendix B. Contributors

Contributors' Addresses

   TBD

Authors' Addresses

Lou Berger LabN Consulting, L.L.C. EMail: lberger@labn.net
Christan Hopps Deutsche Telekom EMail: chopps@chopps.org
Acee Lindem Cisco Systems 301 Midenhall Way Cary, NC 27513 USA EMail: acee@cisco.com
Dean Bogdanovic EMail: ivandean@gmail.com