Network Working Group X. Zhu
Internet-Draft R. Pan
Intended status: Experimental M. Ramalho
Expires: February 25, 2020 S. Mena
Cisco Systems
August 24, 2019

NADA: A Unified Congestion Control Scheme for Real-Time Media
draft-ietf-rmcat-nada-12

Abstract

This document describes NADA (network-assisted dynamic adaptation), a novel congestion control scheme for interactive real-time media applications, such as video conferencing. In the proposed scheme, the sender regulates its sending rate based on either implicit or explicit congestion signaling, in a unified approach. The scheme can benefit from explicit congestion notification (ECN) markings from network nodes. It also maintains consistent sender behavior in the absence of such markings, by reacting to queuing delays and packet losses instead.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on February 25, 2020.

Copyright Notice

Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

Interactive real-time media applications introduce a unique set of challenges for congestion control. Unlike TCP, the mechanism used for real-time media needs to adapt quickly to instantaneous bandwidth changes, accommodate fluctuations in the output of video encoder rate control, and cause low queuing delay over the network. An ideal scheme should also make effective use of all types of congestion signals, including packet loss, queuing delay, and explicit congestion notification (ECN) [RFC3168] markings. The requirements for the congestion control algorithm are outlined in [I-D.ietf-rmcat-cc-requirements]. It highlights that the desired congestion control scheme should avoid flow starvation and attain a reasonable fair share of bandwidth when competing against other flows, adapt quickly, and operate in a stable manner.

This document describes an experimental congestion control scheme called network-assisted dynamic adaptation (NADA). The NADA design benefits from explicit congestion control signals (e.g., ECN markings) from the network, yet also operates when only implicit congestion indicators (delay and/or loss) are available. Such a unified sender behavior distinguishes NADA from other congestion control schemes for real-time media. In addition, its core congestion control algorithm is designed to guarantee stability for path round-trip-times (RTTs) below a prescribed bound (e.g., 250ms with default parameter choices). It further supports weighted bandwidth sharing among competing video flows with different priorities. The signaling mechanism consists of standard RTP timestamp [RFC3550] and RTCP feedback reports. The definition of the desired RTCP feedback message is descirbed in detailed in [I-D.ietf-avtcore-cc-feedback-message] so as to support the successful operation of several congestion control schemes for real-time interactive media.

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. System Overview

Figure 1 shows the end-to-end system for real-time media transport that NADA operates in. Note that there also exist network nodes along the reverse (potentially uncongested) path that the RTCP feedback reports traverse. Those network nodes are not shown in the figure for sake of abrevity.


  +---------+  r_vin  +--------+        +--------+     +----------+
  |  Media  |<--------|  RTP   |        |Network |     |   RTP    |
  | Encoder |========>| Sender |=======>|  Node  |====>| Receiver |  
  +---------+  r_vout +--------+ r_send +--------+     +----------+
                          /|\                                |
                           |                                 |
                           +---------------------------------+
                                 RTCP Feedback Report

Figure 1: System Overview

4. Core Congestion Control Algorithm

Like TCP-Friendly Rate Control (TFRC) [Floyd-CCR00] [RFC5348], NADA is a rate-based congestion control algorithm. In its simplest form, the sender reacts to the collection of network congestion indicators in the form of an aggregated congestion signal, and operates in one of two modes:

This section introduces the list of mathematical notations and describes the core congestion control algorithm at the sender and receiver, respectively. Additional details on recommended practical implementations are described in Section 5.1 and Section 5.2.

4.1. Mathematical Notations

This section summarizes the list of variables and parameters used in the NADA algorithm. Figure 3 also includes the default values for choosing the algorithm parameters either to represent a typical setting in practical applications or based on theoretical and simulation studies. See Section 6.3 for some of the discussions on the impact of parameter values. In the experimental phase of this draft, additional studies in real-world settings will gather further learnings on how to choose and adapt these parameter values in practical deployment.

  +--------------+-------------------------------------------------+
  | Notation     | Variable Name                                   |
  +--------------+-------------------------------------------------+
  | t_curr       | Current timestamp                               |
  | t_last       | Last time sending/receiving a feedback          |
  | delta        | Observed interval between current and previous  |
  |              | feedback reports: delta = t_curr-t_last         |
  | r_ref        | Reference rate based on network congestion      |
  | r_send       | Sending rate                                    |                
  | r_recv       | Receiving rate                                  |
  | r_vin        | Target rate for video encoder                   |
  | r_vout       | Output rate from video encoder                  |
  | d_base       | Estimated baseline delay                        |
  | d_fwd        | Measured and filtered one-way delay             |
  | d_queue      | Estimated queuing delay                        |
  | d_tilde      | Equivalent delay after non-linear warping       |
  | p_mark       | Estimated packet ECN marking ratio              |
  | p_loss       | Estimated packet loss ratio                     |
  | x_curr       | Aggregate congestion signal                     |
  | x_prev       | Previous value of aggregate congestion signal   |
  | x_diff       | Change in aggregate congestion signal w.r.t.    |
  |              | its previous value: x_diff = x_curr - x_prev    |
  | rmode        | Rate update mode: (0 = accelerated ramp-up;     |
  |              | 1 = gradual update)                             |
  | gamma        | Rate increase multiplier in accelerated ramp-up | 
  |              | mode                                            |
  | loss_int     | Measured average loss interval in packet count  |
  | loss_exp     | Threshold value for setting the last observed   |
  |              | packet loss to expiration                       |
  | rtt          | Estimated round-trip-time at sender             |
  | buffer_len   | Rate shaping buffer occupancy measured in bytes |
  +--------------+-------------------------------------------------+
        

Figure 2: List of variables.

   +--------------+----------------------------------+----------------+
   | Notation     | Parameter Name                   | Default Value  |
   +--------------+----------------------------------+----------------+
   | PRIO         | Weight of priority of the flow   |    1.0
   | RMIN         | Minimum rate of application      |    150 Kbps    |
   |              | supported by media encoder       |                |
   | RMAX         | Maximum rate of application      |    1.5 Mbps    |
   |              | supported by media encoder       |                |
   | XREF         | Reference congestion level       |    10ms        |
   | KAPPA        | Scaling parameter for gradual    |    0.5         |
   |              | rate update calculation          |                |
   | ETA          | Scaling parameter for gradual    |    2.0         |
   |              | rate update calculation          |                |
   | TAU          | Upper bound of RTT in gradual    |    500ms       |
   |              | rate update calculation          |                |
   | DELTA        | Target feedback interval         |    100ms       |
   +..............+..................................+................+
   | LOGWIN       | Observation window in time for   |    500ms       |
   |              | calculating packet summary       |                |
   |              | statistics at receiver           |                |
   | QEPS         | Threshold for determining queuing|     10ms       |
   |              | delay build up at receiver       |                |
   | DFILT        | Bound on filtering delay         |    120ms       |
   | GAMMA_MAX    | Upper bound on rate increase     |      0.5       |
   |              | ratio for accelerated ramp-up    |                |
   | QBOUND       | Upper bound on self-inflicted    |    50ms        | 
   |              | queuing delay during ramp up     |                |
   +..............+..................................+................+
   | MULTILOSS    | Multiplier for self-scaling the  |     7.         |
   |              | expiration threshold of the last |                |
   |              | observed loss (loss_exp) based on|                |
   |              | measured average loss interval   |                |
   |              | (loss_int)                       |                |
   | QTH          | Delay threshold for invoking     |     50ms       |
   |              | non-linear warping               |                |
   | LAMBDA       | Scaling parameter in the         |     0.5        |
   |              | exponent of non-linear warping   |                |
   +..............+..................................+................+
   | PLRREF       | Reference packet loss ratio      |    0.01        |
   | PMRREF       | Reference packet marking ratio   |    0.01        |
   | DLOSS        | Reference delay penalty for loss |    10ms        |
   |              | when packet loss ratio is at     |                |
   |              | PLRREF                           |                |
   | DMARK        | Reference delay penalty for ECN  |     2ms        |
   |              | marking when packet marking      |                |
   |              | is at PMRREF                     |                |                  
   +..............+..................................+................+ 
   | FPS          | Frame rate of incoming video     |     30         |
   | BETA_S       | Scaling parameter for modulating |    0.1         |
   |              | outgoing sending rate            |                |
   | BETA_V       | Scaling parameter for modulating |    0.1         |
   |              | video encoder target rate        |                |
   | ALPHA        | Smoothing factor in exponential  |    0.1         |
   |              | smoothing of packet loss and     |                |
   |              | marking ratios                   |       
   +--------------+----------------------------------+----------------+
        

Figure 3: List of algorithm parameters and their default values.

4.2. Receiver-Side Algorithm

The receiver-side algorithm can be outlined as below:

  On initialization:
    set d_base = +INFINITY
    set p_loss = 0
    set p_mark = 0 
    set r_recv = 0 
    set both t_last and t_curr as current time in milliseconds

  On receiving a media packet:
    obtain current timestamp t_curr from system clock
    obtain from packet header sending time stamp t_sent
    obtain one-way delay measurement: d_fwd = t_curr - t_sent
    update baseline delay: d_base = min(d_base, d_fwd)
    update queuing delay:  d_queue = d_fwd - d_base
    update packet loss ratio estimate p_loss
    update packet marking ratio estimate p_mark
    update measurement of receiving rate r_recv

  On time to send a new feedback report (t_curr - t_last > DELTA): 
    calculate non-linear warping of delay d_tilde if packet loss exists
    calculate current aggregate congestion signal x_curr
    determine mode of rate adaptation for sender: rmode
    send feedback containing values of: rmode, x_curr, and r_recv
    update t_last = t_curr
 

In order for a delay-based flow to hold its ground when competing against loss-based flows (e.g., loss-based TCP), it is important to distinguish between different levels of observed queuing delay. For instance, over wired connections, a moderate queuing delay value on the order of tens of milliseonds is likely self-inflicted or induced by other delay-based flows, whereas a high queuing delay value of several hundreds of milliseconds may indicate the presence of a loss-based flow that does not refrain from increased delay.

If the last observed packet loss is within the expiration window of loss_exp (measured in terms of packet counts), the estimated queuing delay follows a non-linear warping:


           / d_queue,                   if d_queue<QTH;
           |
d_tilde = <                                           (1)
           |                  (d_queue-QTH)  
           \ QTH exp(-LAMBDA ---------------) , otherwise.
                                 QTH

    

In (1), the queuing delay value is unchanged when it is below the first threshold QTH; otherwise it is scaled down following a non-linear curve. This non-linear warping is inspired by the delay-adaptive congestion window backoff policy in [Budzisz-TON11], so as to "gradually nudge" the controller to operate based on loss-induced congestion signals when competing against loss-based flows. The exact form of the non-linear function has been simplified with respect to [Budzisz-TON11]. The value of the threshold QTH should be carefully tuned for different operational environments, so as to avoid potential risks of prematurely discounting the congestion signal level. Typically, a higher value of QTH is required in a noisier environment (e.g., over wireless connections, or where the video stream encounters many time-varying background competing traffic) so as to stay robust against occasional non-congestion-induced delay spikes. Additional insights on how this value can be tuned or auto-tuned should be gathered from carrying out experimental studies in different real-world deployment scenarios.

The value of loss_exp is configured to self-scale with the average packet loss interval loss_int with a multiplier MULTILOSS:

	   
      loss_exp = MULTILOSS * loss_int. 
				                   
    

Estimation of the average loss interval loss_int, in turn, follows Section 5.4 of the TCP Friendly Rate Control (TFRC) protocol.

In practice, it is recommended to linearly interpolate between the warped (d_tilde) and non-warped (d_queue) values of the queuing delay during the transitional period lasting for the duration of loss_int.

The aggregate congestion signal is:


                         / p_mark \^2        / p_loss \^2 
x_curr = d_tilde + DMARK*|--------|  + DLOSS*|--------|.  (2) 
                         \ PMRREF /          \ PLRREF /   
    		
    

Here, DMARK is prescribed reference delay penalty associated with ECN markings at the reference marking ratio of PMRREF; DLOSS is prescribed reference delay penalty associated with packet losses at the reference packet loss ratio of PLRREF. The value of DLOSS and DMARK does not depend on configurations at the network node. Since ECN-enabled active queue management schemes typically mark a packet before dropping it, the value of DLOSS SHOULD be higher than that of DMARK. Furthermore, the values of DLOSS and DMARK need to be set consistently across all NADA flows sharing the same bottleneck link, so that they can compete fairly.

In the absence of packet marking and losses, the value of x_curr reduces to the observed queuing delay d_queue. In that case the NADA algorithm operates in the regime of delay-based adaptation.

Given observed per-packet delay and loss information, the receiver is also in a good position to determine whether the network is underutilized and recommend the corresponding rate adaptation mode for the sender. The criteria for operating in accelerated ramp-up mode are:

Otherwise the algorithm operates in graduate update mode.

4.3. Sender-Side Algorithm

The sender-side algorithm is outlined as follows:

  on initialization:
    set r_ref = RMIN
    set rtt = 0
    set x_prev = 0
    set t_last and t_curr as current system clock time

  on receiving feedback report:
    obtain current timestamp from system clock: t_curr
    obtain values of rmode, x_curr, and r_recv from feedback report
    update estimation of rtt
    measure feedback interval: delta = t_curr - t_last
    if rmode == 0:
      update r_ref following accelerated ramp-up rules
    else:
      update r_ref following gradual update rules

    clip rate r_ref within the range of minimum rate (RMIN)
    and maximum rate (RMAX).  
    x_prev = x_curr
    t_last = t_curr  

In accelerated ramp-up mode, the rate r_ref is updated as follows:

                                QBOUND
    gamma = min(GAMMA_MAX, ------------------)     (3)
                            rtt+DELTA+DFILT

    r_ref = max(r_ref, (1+gamma) r_recv)           (4)
    		

The rate increase multiplier gamma is calculated as a function of upper bound of self-inflicted queuing delay (QBOUND), round-trip-time (rtt), target feedback interval (DELTA) and bound on filtering delay for calculating d_queue (DFILT). It has a maximum value of GAMMA_MAX. The rationale behind (3)-(4) is that the longer it takes for the sender to observe self-inflicted queuing delay build-up, the more conservative the sender should be in increasing its rate, hence the smaller the rate increase multiplier.

In gradual update mode, the rate r_ref is updated as:

    x_offset = x_curr - PRIO*XREF*RMAX/r_ref          (5)

    x_diff   = x_curr - x_prev                        (6) 

                           delta    x_offset
    r_ref = r_ref - KAPPA*-------*------------*r_ref
                            TAU       TAU

                                x_diff
                  - KAPPA*ETA*---------*r_ref         (7)
                                 TAU    		

The rate changes in proportion to the previous rate decision. It is affected by two terms: offset of the aggregate congestion signal from its value at equilibrium (x_offset) and its change (x_diff). Calculation of x_offset depends on maximum rate of the flow (RMAX), its weight of priority (PRIO), as well as a reference congestion signal (XREF). The value of XREF is chosen so that the maximum rate of RMAX can be achieved when the observed congestion signal level is below PRIO*XREF.

At equilibrium, the aggregated congestion signal stablizes at x_curr = PRIO*XREF*RMAX/r_ref. This ensures that when multiple flows share the same bottleneck and observe a common value of x_curr, their rates at equilibrium will be proportional to their respective priority levels (PRIO) and the range between minimum and maximum rate. Values of the minimum rate (RMIN) and maximum rate (RMAX) will be provided by the media codec, for instance, as outlined by [I-D.ietf-rmcat-cc-codec-interactions]. In the absense of such information, NADA sender will choose a default value of 0 for RMIN, and 3Mbps for RMAX.

As mentioned in the sender-side algorithm, the final rate is always clipped within the dynamic range specified by the application:


    r_ref = min(r_ref, RMAX)        (8)
    r_ref = max(r_ref, RMIN)        (9)

The above operations ignore many practical issues such as clock synchronization between sender and receiver, filtering of noise in delay measurements, and base delay expiration. These will be addressed in Section 5.

5. Practical Implementation of NADA

5.1. Receiver-Side Operation

The receiver continuously monitors end-to-end per-packet statistics in terms of delay, loss, and/or ECN marking ratios. It then aggregates all forms of congestion indicators into the form of an equivalent delay and periodically reports this back to the sender. In addition, the receiver tracks the receiving rate of the flow and includes that in the feedback message.

5.1.1. Estimation of one-way delay and queuing delay

The delay estimation process in NADA follows a similar approach as in earlier delay-based congestion control schemes, such as LEDBAT. Instead of relying on RTP timestamps, the NADA sender generates its own timestamp based on local system clock and embeds that information in the transport packet header. The NADA receiver estimates the forward delay as having a constant base delay component plus a time varying queuing delay component. The base delay is estimated as the minimum value of one-way delay observed over a relatively long period (e.g., tens of minutes), whereas the individual queuing delay value is taken to be the difference between one-way delay and base delay. By re-estimating the base delay periodically, one can avoid the potential issue of base delay expiration, whereby an earlier measured base delay value is no longer valid due to underlying route changes. All delay estimations are based on sender timestamps with a recommended granularity of 100 microseconds or higher.

The individual sample values of queuing delay should be further filtered against various non-congestion-induced noise, such as spikes due to processing "hiccup" at the network nodes. Therefore, in addition to calculating the value of queuing delay using d_queue = d_fwd - d_base, as expressed in Section 5.1, current implementation further employs a minimum filter with a window size of 15 samples over per-packet queuing delay values.

5.1.2. Estimation of packet loss/marking ratio

The receiver detects packet losses via gaps in the RTP sequence numbers of received packets. For interactive real-time media application with stringent latency constraint (e.g., video conferencing), the receiver avoids the packet re-ordering delay by treating out-of-order packets as losses. The instantaneous packet loss ratio p_inst is estimated as the ratio between the number of missing packets over the number of total transmitted packets within the recent observation window LOGWIN. The packet loss ratio p_loss is obtained after exponential smoothing:

		
    p_loss = ALPHA*p_inst + (1-ALPHA)*p_loss.   (10) 
    

The filtered result is reported back to the sender as the observed packet loss ratio p_loss.

Estimation of packet marking ratio p_mark follows the same procedure as above. It is assumed that ECN marking information at the IP header can be passed to the receiving endpoint, e.g., by following the mechanism described in [RFC6679].

5.1.3. Estimation of receiving rate

It is fairly straighforward to estimate the receiving rate r_recv. NADA maintains a recent observation window with time span of LOGWIN, and simply divides the total size of packets arriving during that window over the time span. The receiving rate (r_recv) can be calculated at either the sender side based on the per-packet feedback from the receiver, or included as part of the feedback report.

5.2. Sender-Side Operation

Figure 4 provides a detailed view of the NADA sender. Upon receipt of an RTCP feedback report from the receiver, the NADA sender calculates the reference rate r_ref as specified in Section 4.3. It further adjusts both the target rate for the live video encoder r_vin and the sending rate r_send over the network based on the updated value of r_ref and rate shaping buffer occupancy buffer_len.

The NADA sender behavior stays the same in the presence of all types of congestion indicators: delay, loss, and ECN marking. This unified approach allows a graceful transition of the scheme as the network shifts dynamically between light and heavy congestion levels.

                   +----------------+             
                   |  Calculate     | <---- RTCP report
                   | Reference Rate | 
                   -----------------+
                           | r_ref
              +------------+-------------+
              |                          |
             \|/                        \|/
      +-----------------+           +---------------+
      | Calculate Video |           |   Calculate   |
      |  Target Rate    |           | Sending Rate  |
      +-----------------+           +---------------+
          |        /|\                 /|\      |   
    r_vin |         |                   |       |
         \|/        +-------------------+       |       
      +----------+          | buffer_len        |  r_send
      |  Video   | r_vout  -----------+        \|/
      |  Encoder |-------->   |||||||||=================>  
      +----------+         -----------+    RTP packets     
                          Rate Shaping Buffer         		

Figure 4: NADA Sender Structure

5.2.1. Rate shaping buffer

The operation of the live video encoder is out of the scope of the design for the congestion control scheme in NADA. Instead, its behavior is treated as a black box.

A rate shaping buffer is employed to absorb any instantaneous mismatch between encoder rate output r_vout and regulated sending rate r_send. Its current level of occupancy is measured in bytes and is denoted as buffer_len.

A large rate shaping buffer contributes to higher end-to-end delay, which may harm the performance of real-time media communications. Therefore, the sender has a strong incentive to prevent the rate shaping buffer from building up. The mechanisms adopted are:

5.2.2. Adjusting video target rate and sending rate

If the level of occupancy in the rate shaping buffer is accessible at the sender, such information can be leveraged to further adjust the target rate of the live video encoder r_vin as well as the actual sending rate r_send. The purpose of such adjustments is to mitigate the additional latencies introduced by the rate shaping buffer. The amount of rate adjustment can be calculated as follows:


    r_diff_v = min(0.05*r_ref, BETA_V*8*buffer_len*FPS).     (11) 
    r_diff_s = min(0.05*r_ref, BETA_S*8*buffer_len*FPS).     (12) 
    r_vin  = max(RMIN, r_ref - r_diff_v).      (13) 
    r_send = min(RMAX, r_ref + r_diff_s).    (14)

In (11) and (12), the amount of adjustment is calculated as proportional to the size of the rate shaping buffer but is bounded by 5% of the reference rate r_ref calculated from network congestion feedback alone. This ensures that the adjustment introduced by the rate shaping buffer will not counteract with the core congestion control process. Equations (13) and (14) indicate the influence of the rate shaping buffer. A large rate shaping buffer nudges the encoder target rate slightly below -- and the sending rate slightly above -- the reference rate r_ref. The final video target rate (r_vin) and sending rate (r_send) are further bounded within the original range of [RMIN, RMAX].

Intuitively, the amount of extra rate offset needed to completely drain the rate shaping buffer within the duration of a single video frame is given by 8*buffer_len*FPS, where FPS stands for the reference frame rate of the video. The scaling parameters BETA_V and BETA_S can be tuned to balance between the competing goals of maintaining a small rate shaping buffer and deviating from the reference rate point. Empirical observations show that the rate shaping buffer for a responsive live video encoder typically stays empty and only occasionally holds a large frame (e.g., when an intra-frame is produced) in transit. Therefore, the rate adjustment introduced by this mechanism is expected to be minor. For instance, a rate shaping buffer of 2000 Bytes will lead to a rate adjustment of 48 Kbps given the recommended scaling parameters of BETA_V = 0.1 and BETA_S = 0.1 and reference frame rate of FPS = 30.

5.3. Feedback Message Requirements

The following list of information is required for NADA congestion control to function properly:

The above list of information can be accommodated by 48 bits, or 6 bytes, in total. They can be either included in the feedback report from the receiver, or, in the case where all receiver-side calculations are moved to the sender, derived from per-packet information from the feedback message as defined in [I-D.ietf-avtcore-cc-feedback-message]. Choice of the feedback message interval DELTA is discussed in Section 6.3. A target feedback interval of DELTA=100ms is recommended.

6. Discussions and Further Investigations

This section discussed the various design choices made by NADA, potential alternative variants of its implementation, and guidelines on how the key algorithm parameters can be chosen. Section 8 recommends additional experimental setups to further explore these topics.

6.1. Choice of delay metrics

The current design works with relative one-way-delay (OWD) as the main indication of congestion. The value of the relative OWD is obtained by maintaining the minimum value of observed OWD over a relatively long time horizon and subtract that out from the observed absolute OWD value. Such an approach cancels out the fixed difference between the sender and receiver clocks. It has been widely adopted by other delay-based congestion control approaches such as [RFC6817]. As discussed in [RFC6817], the time horizon for tracking the minimum OWD needs to be chosen with care: it must be long enough for an opportunity to observe the minimum OWD with zero standing queue along the path, and sufficiently short so as to timely reflect "true" changes in minimum OWD introduced by route changes and other rare events.

The potential drawback in relying on relative OWD as the congestion signal is that when multiple flows share the same bottleneck, the flow arriving late at the network experiencing a non-empty queue may mistakenly consider the standing queuing delay as part of the fixed path propagation delay. This will lead to slightly unfair bandwidth sharing among the flows.

Alternatively, one could move the per-packet statistical handling to the sender instead and use relative round-trip-time (RTT) in lieu of relative OWD, assuming that per-packet acknowledgements are available. The main drawback of RTT-based approach is the noise in the measured delay in the reverse direction.

Note that the choice of either delay metric (relative OWD vs. RTT) involves no change in the proposed rate adaptation algorithm. Therefore, comparing the pros and cons regarding which delay metric to adopt can be kept as an orthogonal direction of investigation.

6.2. Method for delay, loss, and marking ratio estimation

Like other delay-based congestion control schemes, performance of NADA depends on the accuracy of its delay measurement and estimation module. Appendix A in [RFC6817] provides an extensive discussion on this aspect.

The current recommended practice of applying minimum filter with a window size of 15 samples suffices in guarding against processing delay outliers observed in wired connections. For wireless connections with a higher packet delay variation (PDV), more sophisticated techniques on de-noising, outlier rejection, and trend analysis may be needed.

More sophisticated methods in packet loss ratio calculation, such as that adopted by [Floyd-CCR00], will likely be beneficial. These alternatives are part of the experiments this document proposes.

6.3. Impact of parameter values

In the gradual rate update mode, the parameter TAU indicates the upper bound of round-trip-time (RTT) in feedback control loop. Typically, the observed feedback interval delta is close to the target feedback interval DELTA, and the relative ratio of delta/TAU versus ETA dictates the relative strength of influence from the aggregate congestion signal offset term (x_offset) versus its recent change (x_diff), respectively. These two terms are analogous to the integral and proportional terms in a proportional-integral (PI) controller. The recommended choice of TAU=500ms, DELTA=100ms and ETA = 2.0 corresponds to a relative ratio of 1:10 between the gains of the integral and proportional terms. Consequently, the rate adaptation is mostly driven by the change in the congestion signal with a long-term shift towards its equilibrium value driven by the offset term. Finally, the scaling parameter KAPPA determines the overall speed of the adaptation and needs to strike a balance between responsiveness and stability.

The choice of the target feedback interval DELTA needs to strike the right balance between timely feedback and low RTCP feedback message counts. A target feedback interval of DELTA=100ms is recommended, corresponding to a feedback bandwidth of 16Kbps with 200 bytes per feedback message --- approximately 1.6% overhead for a 1 Mbps flow. Furthermore, both simulation studies and frequency-domain analysis in [IETF-95] have established that a feedback interval below 250ms (i.e., more frequently than 4 feedback messages per second) will not break up the feedback control loop of NADA congestion control.

In calculating the non-linear warping of delay in (1), the current design uses fixed values of QTH for determining whether to perform the non-linear warping). Its value should be carefully tuned for different operational enviornments (e.g., over wired vs. wireless connections), so as to avoid the potential risk of prematurely discounting the congestion signal level. It is possible to adapt its value based on past observed patterns of queuing delay in the presence of packet losses. It needs to be noted that the non-linear warping mechanism may lead to multiple NADA streams stuck in loss-based mode when competing against each other.

In calculating the aggregate congestion signal x_curr, the choice of DMARK and DLOSS influence the steady-state packet loss/marking ratio experienced by the flow at a given available bandwidth. Higher values of DMARK and DLOSS result in lower steady-state loss/marking ratios, but are more susceptible to the impact of individual packet loss/marking events. While the value of DMARK and DLOSS are fixed and predetermined in the current design, this document also encourages futher explorations of a scheme for automatically tuning these values based on desired bandwidth sharing behavior in the presence of other competing loss-based flows (e.g., loss-based TCP).

6.4. Sender-based vs. receiver-based calculation

In the current design, the aggregated congestion signal x_curr is calculated at the receiver, keeping the sender operation completely independent of the form of actual network congestion indications (delay, loss, or marking) in use.

Alternatively, one can shift receiver-side calculations to the sender, whereby the receiver simply reports on per-packet information via periodic feedback messages as defined in [I-D.ietf-avtcore-cc-feedback-message]. Such an approach enables interoperability amongst senders operating on different congestion control schemes, but requires slightly higher overhead in the feedback messages. See additional discussions in [I-D.ietf-avtcore-cc-feedback-message] regarding the desired format of the feedback messages and the recommended feedback intervals.

6.5. Incremental deployment

One nice property of NADA is the consistent video endpoint behavior irrespective of network node variations. This facilitates gradual, incremental adoption of the scheme.

Initially, the proposed congestion control mechanism can be implemented without any explicit support from the network, and relies solely on observed relative one-way delay measurements and packet loss ratios as implicit congestion signals.

When ECN is enabled at the network nodes with RED-based marking, the receiver can fold its observations of ECN markings into the calculation of the equivalent delay. The sender can react to these explicit congestion signals without any modification.

Ultimately, networks equipped with proactive marking based on token bucket level metering can reap the additional benefits of zero standing queues and lower end-to-end delay and work seamlessly with existing senders and receivers.

7. Reference Implementations

The NADA scheme has been implemented in both [ns-2] and [ns-3] simulation platforms. The implementation in ns-2 hosts the calculations as descirbed in Section 4.2 at the receiver side, whereas the implementation in ns-3 hosts these receiver-side calculations at the sender for the sake of interoperability. Extensive ns-2 simulation evaluations of an earlier version of the draft are documented in [Zhu-PV13]. An open source implementation of NADA as part of a ns-3 module is available at [ns3-rmcat]. Evaluation results of the current draft based on ns-3 are presented in [IETF-90] and [IETF-91] for wired test cases as documented in [I-D.ietf-rmcat-eval-test]. Evaluation results of NADA over WiFi-based test cases as defined in [I-D.ietf-rmcat-wireless-tests] are presented in [IETF-93]. These simulation-based evaluations have shown that NADA flows can obtain their fair share of bandwidth when competing against each other. They typically adapt fast in reaction to the arrival and departure of other flows, and can sustain a reasonable throughput when competing against loss-based TCP flows.

[IETF-90] describes the implemention and evaluation of NADA in a lab setting. Preliminary evaluation results of NADA in single-flow and multi-flow test scenarios have been presented in [IETF-91].

A reference implementation of NADA has been carried out by modifying the WebRTC module embedded in the Mozilla open source browser. Presentations from [IETF-103] and [IETF-105] document real-world evaluations of the modified browser driven by NADA. The experimental setting involve remote connections with endpoints over either home or enterprise wireless networks. These evaluations validate the effectiveness of NADA flows in recovering quickly from throughput drops caused by intermittent delay spikes over the last-hop wirelss connections.

8. Suggested Experiments

NADA has been extensively evaluated under various test scenarios, including the collection of test cases specified by [I-D.ietf-rmcat-eval-test] and the subset of WiFi-based test cases in [I-D.ietf-rmcat-wireless-tests]. Additional evaluations have been carried out to characterize how NADA interacts with various active queue management (AQM) schemes such as RED, CoDel, and PIE. Most of these evaluations have been carried out in simulators. A few key test cases have been evaluated in lab environments with implementations embedded in video conferencing clients. It is strongly recommended to carry out implementation and experimentation of NADA in real-world settings. Such exercise will provide insights on how to choose or automatically adapte the values of the key algorithm parameters (see list in Figure 3) as discussed in Section 6.

Additional experiments are suggested for the following scenarios and preferrably over real-world networks:

9. IANA Considerations

This document makes no request of IANA.

10. Security Considerations

The rate adaptation mechanism in NADA relies on feedback from the receiver. As such, it is vulnerable to attacks where feedback messages are hijacked, replaced, or intentionally injected with misleading information resulting in denial of service, similar to those that can affect TCP. It is therefore RECOMMENDED that the RTCP feedback message is at least integrity checked. In addition, [I-D.ietf-avtcore-cc-feedback-message] discusses the potential risk of a receiver providing misleading congestion feedback information and the mechanisms for mitigating such risks.

The modification of sending rate based on send-side rate shaping buffer may lead to temporary excessive congestion over the network in the presence of a unresponsive video encoder. However, this effect can be mitigated by limiting the amount of rate modification introduced by the rate shaping buffer, bounding the size of the rate shaping buffer at the sender, and maintaining a maximum allowed sending rate by NADA.

11. Acknowledgments

The authors would like to thank Randell Jesup, Luca De Cicco, Piers O'Hanlon, Ingemar Johansson, Stefan Holmer, Cesar Ilharco Magalhaes, Safiqul Islam, Michael Welzl, Mirja Kuhlewind, Karen Elisabeth Egede Nielsen, Julius Flohr, Roland Bless, Andreas Smas, and Martin Stiemerling for their valuable review comments and helpful input to this specification.

12. Contributors

The following individuals have contributed to the implementation and evaluation of the proposed scheme, and therefore have helped to validate and substantially improve this specification.

13. References

13.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997.
[RFC3168] Ramakrishnan, K., Floyd, S. and D. Black, "The Addition of Explicit Congestion Notification (ECN) to IP", RFC 3168, DOI 10.17487/RFC3168, September 2001.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R. and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550, July 2003.
[RFC5348] Floyd, S., Handley, M., Padhye, J. and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification", RFC 5348, DOI 10.17487/RFC5348, September 2008.
[RFC6679] Westerlund, M., Johansson, I., Perkins, C., O'Hanlon, P. and K. Carlberg, "Explicit Congestion Notification (ECN) for RTP over UDP", RFC 6679, DOI 10.17487/RFC6679, August 2012.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017.

13.2. Informative References

[Budzisz-TON11] Budzisz, L., Stanojevic, R., Schlote, A., Baker, F. and R. Shorten, "On the Fair Coexistence of Loss- and Delay-Based TCP", IEEE/ACM Transactions on Networking vol. 19, no. 6, pp. 1811-1824, December 2011.
[Floyd-CCR00] Floyd, S., Handley, M., Padhye, J. and J. Widmer, "Equation-based Congestion Control for Unicast Applications", ACM SIGCOMM Computer Communications Review vol. 30, no. 4, pp. 43-56, October 2000.
[I-D.ietf-avtcore-cc-feedback-message] Sarker, Z., Perkins, C., Singh, V. and M. Ramalho, "RTP Control Protocol (RTCP) Feedback for Congestion Control", Internet-Draft draft-ietf-avtcore-cc-feedback-message-04, July 2019.
[I-D.ietf-rmcat-cc-codec-interactions] Zanaty, M., Singh, V., Nandakumar, S. and Z. Sarker, "Congestion Control and Codec interactions in RTP Applications", Internet-Draft draft-ietf-rmcat-cc-codec-interactions-02, March 2016.
[I-D.ietf-rmcat-cc-requirements] Jesup, R. and Z. Sarker, "Congestion Control Requirements for Interactive Real-Time Media", Internet-Draft draft-ietf-rmcat-cc-requirements-09, December 2014.
[I-D.ietf-rmcat-eval-test] Sarker, Z., Singh, V., Zhu, X. and M. Ramalho, "Test Cases for Evaluating RMCAT Proposals", Internet-Draft draft-ietf-rmcat-eval-test-10, May 2019.
[I-D.ietf-rmcat-video-traffic-model] Zhu, X., Cruz, S. and Z. Sarker, "Video Traffic Models for RTP Congestion Control Evaluations", Internet-Draft draft-ietf-rmcat-video-traffic-model-07, February 2019.
[I-D.ietf-rmcat-wireless-tests] Sarker, Z., Johansson, I., Zhu, X., Fu, J., Tan, W. and M. Ramalho, "Evaluation Test Cases for Interactive Real-Time Media over Wireless Networks", Internet-Draft draft-ietf-rmcat-wireless-tests-08, July 2019.
[IETF-103] Zhu, X., Pan, R., Ramalho, M., Mena, S., Jones, P., Fu, J. and S. D'Aronco, "NADA Implementation in Mozilla Browser", November 2018.
[IETF-105] Zhu, X., Pan, R., Ramalho, M., Mena, S., Jones, P., Fu, J. and S. D'Aronco, "NADA Implementation in Mozilla Browser and Draft Update", July 2019.
[IETF-90] Zhu, X., Ramalho, M., Ganzhorn, C., Jones, P. and R. Pan, "NADA Update: Algorithm, Implementation, and Test Case Evalua6on Results", July 2014.
[IETF-91] Zhu, X., Pan, R., Ramalho, M., Mena, S., Ganzhorn, C., Jones, P. and S. D'Aronco, "NADA Algorithm Update and Test Case Evaluations", November 2014.
[IETF-93] Zhu, X., Pan, R., Ramalho, M., Mena, S., Ganzhorn, C., Jones, P., D'Aronco, S. and J. Fu, "Updates on NADA", July 2015.
[IETF-95] Zhu, X., Pan, R., Ramalho, M., Mena, S., Jones, P., Fu, J., D'Aronco, S. and C. Ganzhorn, "Updates on NADA: Stability Analysis and Impact of Feedback Intervals", April 2016.
[ns-2] "The Network Simulator - ns-2"
[ns-3] "The Network Simulator - ns-3"
[ns3-rmcat] Fu, J., Mena, S. and X. Zhu, "NS3 open source module of IETF RMCAT congestion control protocols", November 2017.
[RFC6660] Briscoe, B., Moncaster, T. and M. Menth, "Encoding Three Pre-Congestion Notification (PCN) States in the IP Header Using a Single Diffserv Codepoint (DSCP)", RFC 6660, DOI 10.17487/RFC6660, July 2012.
[RFC6817] Shalunov, S., Hazel, G., Iyengar, J. and M. Kuehlewind, "Low Extra Delay Background Transport (LEDBAT)", RFC 6817, DOI 10.17487/RFC6817, December 2012.
[RFC7567] Baker, F. and G. Fairhurst, "IETF Recommendations Regarding Active Queue Management", BCP 197, RFC 7567, DOI 10.17487/RFC7567, July 2015.
[RFC8033] Pan, R., Natarajan, P., Baker, F. and G. White, "Proportional Integral Controller Enhanced (PIE): A Lightweight Control Scheme to Address the Bufferbloat Problem", RFC 8033, DOI 10.17487/RFC8033, February 2017.
[RFC8290] Hoeiland-Joergensen, T., McKenney, P., Taht, D., Gettys, J. and E. Dumazet, "The Flow Queue CoDel Packet Scheduler and Active Queue Management Algorithm", RFC 8290, DOI 10.17487/RFC8290, January 2018.
[RFC8593] Zhu, X., Mena, S. and Z. Sarker, "Video Traffic Models for RTP Congestion Control Evaluations", RFC 8593, DOI 10.17487/RFC8593, May 2019.
[Zhu-PV13] Zhu, X. and R. Pan, "NADA: A Unified Congestion Control Scheme for Low-Latency Interactive Video", in Proc. IEEE International Packet Video Workshop (PV'13) San Jose, CA, USA, December 2013.

Appendix A. Network Node Operations

NADA can work with different network queue management schemes and does not assume any specific network node operation. As an example, this appendix describes three variants of queue management behavior at the network node, leading to either implicit or explicit congestion signals. It needs to be acknowledged that NADA has not yet been tested with non-probabilistic ECN marking behaviors.

In all three flavors described below, the network queue operates with the simple first-in-first-out (FIFO) principle. There is no need to maintain per-flow state. The system can scale easily with a large number of video flows and at high link capacity.

A.1. Default behavior of drop tail queues

In a conventional network with drop tail or RED queues, congestion is inferred from the estimation of end-to-end delay and/or packet loss. Packet drops at the queue are detected at the receiver, and contributes to the calculation of the aggregated congestion signal x_curr. No special action is required at network node.

A.2. RED-based ECN marking

In this mode, the network node randomly marks the ECN field in the IP packet header following the Random Early Detection (RED) algorithm. Calculation of the marking probability involves the following steps:

    on packet arrival:  
	update smoothed queue size q_avg as:     
	    q_avg = w*q + (1-w)*q_avg. 

  	calculate marking probability p as: 

           / 0,                    if q < q_lo; 
           |
           |        q_avg - q_lo
       p= <  p_max*--------------, if q_lo <= q < q_hi; 
           |         q_hi - q_lo
           |
           \ p = 1,                if q >= q_hi. 

Here, q_lo and q_hi corresponds to the low and high thresholds of queue occupancy. The maximum marking probability is p_max.

The ECN markings events will contribute to the calculation of an equivalent delay x_curr at the receiver. No changes are required at the sender.

A.3. Random Early Marking with Virtual Queues

Advanced network nodes may support random early marking based on a token bucket algorithm originally designed for Pre-Congestion Notification (PCN). The early congestion notification (ECN) bit in the IP header of packets are marked randomly. The marking probability is calculated based on a token-bucket algorithm originally designed for the Pre-Congestion Notification (PCN). The target link utilization is set as 90%; the marking probability is designed to grow linearly with the token bucket size when it varies between 1/3 and 2/3 of the full token bucket limit.

Calculation of the marking probability involves the following steps:

			
    upon packet arrival: 
	meter packet against token bucket (r,b);
	
	update token level b_tk;

        calculate the marking probability as:

         / 0,                     if b-b_tk < b_lo; 
         |
         |          b-b_tk-b_lo
    p = <  p_max* --------------, if b_lo<= b-b_tk <b_hi; 
         |           b_hi-b_lo
         |
         \ 1,                     if b-b_tk>=b_hi. 

Here, the token bucket lower and upper limits are denoted by b_lo and b_hi, respectively. The parameter b indicates the size of the token bucket. The parameter r is chosen to be below capacity, resulting in slight under-utilization of the link. The maximum marking probability is p_max.

The ECN markings events will contribute to the calculation of an equivalent delay x_curr at the receiver. No changes are required at the sender. The virtual queuing mechanism from the PCN-based marking algorithm will lead to additional benefits such as zero standing queues.

Authors' Addresses

Xiaoqing Zhu Cisco Systems 12515 Research Blvd., Building 4 Austin, TX 78759 USA EMail: xiaoqzhu@cisco.com
Rong Pan * * Pending affiliation change. EMail: rong.pan@gmail.com
Michael A. Ramalho Cisco Systems, Inc. 8000 Hawkins Road Sarasota, FL 34241 USA Phone: +1 919 476 2038 EMail: mar42@cornell.edu
Sergio Mena de la Cruz Cisco Systems EPFL, Quartier de l'Innovation, Batiment E Ecublens, Vaud 1015 Switzerland EMail: semena@cisco.com