| Network Working Group | M. Boucadair, Ed. |
| Internet-Draft | Orange |
| Intended status: Standards Track | S. Sivakumar |
| Expires: March 28, 2019 | Cisco Systems |
| C. Jacquenet | |
| Orange | |
| S. Vinapamula | |
| Juniper Networks | |
| Q. Wu | |
| Huawei | |
| September 24, 2018 |
A YANG Module for Network Address Translation (NAT) and Network Prefix Translation (NPT)
draft-ietf-opsawg-nat-yang-16
This document defines a YANG module for the Network Address Translation (NAT) function.
Network Address Translation from IPv4 to IPv4 (NAT44), Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers (NAT64), Customer-side transLATor (CLAT), Stateless IP/ICMP Translation (SIIT), Explicit Address Mappings for Stateless IP/ICMP Translation (SIIT EAM), IPv6 Network Prefix Translation (NPTv6), and Destination NAT are covered in this document.
Please update these statements within the document with the RFC number to be assigned to this document:
Please update the "revision" date of the YANG module.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 28, 2019.
Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This document defines a data model for Network Address Translation (NAT) and Network Prefix Translation (NPT) capabilities using the YANG data modeling language [RFC7950].
Traditional NAT is defined in [RFC2663], while Carrier Grade NAT (CGN) is defined in [RFC6888]. Unlike traditional NAT, the CGN is used to optimize the usage of global IP address space at the scale of a domain: a CGN is not managed by end users, but by service providers instead. This document covers both traditional NATs and CGNs.
This document also covers NAT64 [RFC6146], customer-side translator (CLAT) [RFC6877], Stateless IP/ICMP Translation (SIIT) [RFC7915], Explicit Address Mappings for Stateless IP/ICMP Translation (EAM) [RFC7757], IPv6 Network Prefix Translation (NPTv6) [RFC6296], and Destination NAT. The full set of translation schemes that are in scope is included in Section 2.2.
Sample examples are provided in Appendix A. These examples are not intended to be exhaustive.
This document makes use of the following terms:
The usage of the term NAT in this document refers to any translation flavor (NAT44, NAT64, etc.) indifferently.
This document uses the term "session" as defined in [RFC2663] and [RFC6146] for NAT64.
This document follows the guidelines of [RFC6087], uses the common YANG types defined in [RFC6991], and adopts the Network Management Datastore Architecture (NMDA). The meaning of the symbols in tree diagrams is defined in [RFC8340].
The NAT YANG module is designed to cover dynamic implicit mappings and static explicit mappings. The required functionality to instruct dynamic explicit mappings is defined in separate documents such as [I-D.boucadair-pcp-yang]. Considerations about instructing explicit dynamic means (e.g., [RFC6887], [RFC6736], or [RFC8045]) are out of scope. As a reminder, REQ-9 of [RFC6888] requires that a CGN must implement a protocol giving subscribers explicit control over NAT mappings; that protocol should be the Port Control Protocol [RFC6887].
A single NAT device can have multiple NAT instances; each of these instances can be provided with its own policies (e.g., be responsible for serving a group of hosts). This document does not make any assumption about how internal hosts or flows are associated with a given NAT instance.
The NAT YANG module assumes that each NAT instance can be enabled/disabled, be provisioned with a specific set of configuration data, and maintains its own mapping tables.
The NAT YANG module allows for a NAT instance to be provided with multiple NAT policies (/nat/instances/instance/policy). The document does not make any assumption about how flows are associated with a given NAT policy of a given NAT instance. Classification filters are out of scope.
Defining multiple NAT instances or configuring multiple NAT policies within one single NAT instance is implementation- and deployment-specific.
This YANG module does not provide any method to instruct a NAT function to enable the logging feature or to specify the information to be logged for administrative or regulatory reasons (Section 2.3 of [RFC6908] and REQ-12 of [RFC6888]). Those considerations are out of the scope of this document.
The following translation modes are supported:
[I-D.ietf-softwire-dslite-yang] specifies an extension to the NAT YANG module to support DS-Lite.
The YANG "feature" statement is used to indicate which of the different translation modes is relevant for a specific data node. Table 1 lists defined features:
| Translation Mode | YANG Feature |
|---|---|
| Basic NAT44 | basic-nat44 |
| NAPT | napt44 |
| Destination NAT | dst-nat |
| Stateful NAT64 | nat64 |
| Stateless IPv4/IPv6 translation | siit |
| CLAT | clat |
| EAM | eam |
| NPTv6 | nptv6 |
The following translation modes do not require defining dedicated features:
The NAT YANG module provides a method to retrieve the capabilities of a NAT instance (including, list of supported translation modes, list of supported protocols, port restriction support status, supported NAT mapping types, supported NAT filtering types, port range allocation support status, port parity preservation support status, port preservation support status, the behavior for handling fragments (all, out-of-order, in-order)).
This document assumes NAT behavioral recommendations for UDP [RFC4787], TCP [RFC5382], and ICMP [RFC5508] are enabled by default.
Furthermore, the NAT YANG module relies upon the recommendations detailed in [RFC6888] and [RFC7857].
The module is structured to support protocols other than UDP, TCP, and ICMP. Concretely, the module allows the operator to enable translation for other transport protocols when required (/nat/instances/instance/policy/transport-protocols). Moreover, the mapping table is designed so that it can indicate any transport protocol. For example, this module may be used to manage a DCCP-capable NAT that adheres to [RFC5597].
Future extensions may be needed to cover NAT-related considerations that are specific to other transport protocols such as SCTP [I-D.ietf-tsvwg-natsupp]. Typically, the mapping entry can be extended to record two optional SCTP-specific parameters: Internal Verification Tag (Int-VTag) and External Verification Tag (Ext-VTag).
This document only specifies transport protocol specific timers for UDP, TCP, and ICMP. While some timers could potentially be generalized for other connection-oriented protocols, this document does not follow such an approach because there is no standard document specifying such generic behavior. Future documents may be edited to clarify how to reuse TCP-specific timers when needed.
The NAT YANG module assumes that blocks of IP external addresses (external-ip-address-pool) can be provisioned to the NAT function. These blocks may be contiguous or not.
This behavior is aligned with [RFC6888] which specifies that a NAT function should not have any limitations on the size or the contiguity of the external address pool. In particular, the NAT function must be configurable with contiguous or non-contiguous external IPv4 address ranges. To accommodate traditional NAT, the module allows for a single IP address to be configured for external-ip-address-pool.
Likewise, one or multiple IP address pools may be configured for Destination NAT (dst-ip-address-pool).
Port numbers can be assigned by a NAT individually (that is, a single port is assigned on a per session basis), but this port allocation scheme may not be optimal for logging purposes (Section 12 of [RFC6269]). A NAT function should be able to assign port sets (e.g., [RFC7753]) to optimize the volume of the logging data (REQ-14 of [RFC6888]). Both allocation schemes are supported in the NAT YANG module.
When port set assignment is activated (i.e., port-allocation-type==port-range-allocation), the NAT can be provided with the size of the port set to be assigned (port-set-size).
Some NATs restrict the source port numbers (e.g., Lightweight 4over6 [RFC7596], MAP-E [RFC7597]). Two schemes of port set assignments (port-set-restrict) are supported in this document:
A TCP/UDP mapping entry maintains an association between the following information:
An ICMP mapping entry maintains an association between the following information:
As a reminder, all the ICMP Query messages contain an 'Identifier' field, which is referred to in this document as the 'ICMP Identifier'.
To cover TCP, UDP, and ICMP, the NAT YANG module assumes the following structure of a mapping entry:
In order to cover both NAT64 and NAT44 flavors, the NAT mapping structure allows for the inclusion of an IPv4 or an IPv6 address as an internal IP address. Remaining fields are common to both NAT schemes.
For example, the mapping that will be created by a NAT64 upon receipt of a TCP SYN from source address 2001:db8:aaaa::1 and source port number 25636 to destination IP address 2001:db8:1234::198.51.100.1 and destination port number 8080 is shown in Table 2. This example assumes EDM (Endpoint-Dependent Mapping).
| Mapping Entry Attribute | Value |
|---|---|
| type | dynamic implicit mapping |
| transport-protocol | 6 (TCP) |
| internal-src-address | 2001:db8:aaaa::1 |
| internal-src-port | 25636 |
| external-src-address | T (an IPv4 address configured on the NAT64) |
| external-src-port | t (a port number that is chosen by the NAT64) |
| internal-dst-address | 2001:db8:1234::198.51.100.1 |
| internal-dst-port | 8080 |
| external-dst-address | 198.51.100.1 |
| external-dst-port | 8080 |
The mappings that will be created by a NAT44 upon receipt of an ICMP request from source address 198.51.100.1 and ICMP identifier (ID1) to destination IP address 198.51.100.11 is depicted in Table 3. This example assumes EIM (Endpoint-Independent Mapping).
| Mapping Entry Attribute | Value |
|---|---|
| type | dynamic implicit mapping |
| transport-protocol | 1 (ICMP) |
| internal-src-address | 198.51.100.1 |
| internal-src-port | ID1 |
| external-src-address | T (an IPv4 address configured on the NAT44) |
| external-src-port | ID2 (an ICMP identifier that is chosen by the NAT44) |
The mapping that will be created by a NAT64 (EIM mode) upon receipt of an ICMP request from source address 2001:db8:aaaa::1 and ICMP identifier (ID1) to destination IP address 2001:db8:1234::198.51.100.1 is shown in Table 4.
| Mapping Entry Attribute | Value |
|---|---|
| type | dynamic implicit mapping |
| transport-protocol | 58 (ICMPv6) |
| internal-src-address | 2001:db8:aaaa::1 |
| internal-src-port | ID1 |
| external-src-address | T (an IPv4 address configured on the NAT64) |
| external-src-port | ID2 (an ICMP identifier that is chosen by the NAT64) |
Note that a mapping table is maintained only for stateful NAT functions. Particularly:
In order to comply with CGN deployments in particular, the NAT YANG module allows limiting the number of external ports per subscriber (port-quota) and the amount of state memory allocated per mapping and per subscriber (mapping-limits and connection-limits). According to [RFC6888], the module is designed to allow for the following:
Table 5 lists the various limits that can be set using the NAT YANG module. Once a limit is reached, packets that would normally trigger new port mappings or be translated because they match existing mappings, are dropped by the translator.
| Limit | Description |
|---|---|
| port-quota | Specifies a port quota to be assigned per subscriber. It corresponds to the maximum number of ports to be used by a subscriber. The port quota can be configured to apply to all protocols or to a specific protocol. Distinct port quota may be configured per protocol. |
| fragments-limit | In order to prevent denial of service attacks that can be caused by fragments, this parameter is used to limit the number of out-of-order fragments that can be handled by a translator. |
| mapping-limits | This parameter can be used to control the maximum number of subscribers that can be serviced by a NAT instance (limit-subscriber) and the maximum number of address and/or port mappings that can be maintained by a NAT instance (limit-address-mappings and limit-port-mappings). Also, limits specific to protocols (e.g., TCP, UDP, ICMP) can also be specified (limit-per-protocol). |
| connection-limits | In order to prevent exhausting the resources of a NAT implementation and to ensure fairness usage among subscribers, various rate-limits can be specified. Rate-limiting can be enforced per subscriber ((limit-subscriber), per NAT instance (limit-per-instance), and/or be specified for each supported protocol (limit-per-protocol). |
Table 6 describes limits, that once exceeded, will trigger notifications to be generated:
| Notification Threshold | Description |
|---|---|
| high-threshold | Used to notify high address utilization of a given pool. When exceeded, a nat-pool-event notification will be generated. |
| low-threshold | Used to notify low address utilization of a given pool. An administrator is supposed to configure low-threshold so that it can reflect an abnormal usage of NAT resources. When exceeded, a nat-pool-event notification will be generated. |
| notify-addresses-usage | Used to notify high address utilization of all pools configured to a NAT instance. When exceeded, a nat-instance-event will be generated. |
| notify-ports-usage | Used to notify high port allocation taking into account all pools configured to a NAT instance. When exceeded, a nat-instance-event notification will be generated. |
| notify-subscribers-limit | Used to notify a high number of active subscribers that are serviced by a NAT instance. When exceeded, a nat-instance-event notification will be generated. |
In order to prevent a NAT implementation from generating frequent notifications, the NAT YANG module supports the following limits (Table 7) used to control how frequent notifications can be generated. That is, notifications are subject to rate-limiting imposed by these intervals.
| Interval | Description |
|---|---|
| notify-pool-usage/notify-interval | Indicates the minimum number of seconds between successive notifications for a given address pool. |
| notification-limits/notify-interval | Indicates the minimum number of seconds between successive notifications for a NAT instance. |
The module is designed to specify an external realm on which the NAT function must be applied (external-realm). The module supports indicating an interface as an external realm [RFC8343], but the module is extensible so that other choices can be indicated in the future (e.g., Virtual Routing and Forwarding (VRF) instance).
Distinct external realms can be provided as a function of the NAT policy (see for example, Section 4 of [RFC7289]).
If no external realm is provided, this assumes that the system is able to determine the external interface (VRF instance, etc.) on which the NAT will be applied. Typically, the WAN and LAN interfaces of a CPE are determined by the CPE.
Section of 5.1 of [RFC7659] indicates that the NATV2-MIB assumes that the following information is configured on the NAT by some means, not specified in [RFC7659]:
All the above parameters can be configured by means of the NAT YANG module.
Unlike the NATV2-MIB, the NAT YANG module allows to configure multiple policies per NAT instance.
The tree structure of the NAT YANG module is provided below:
module: ietf-nat
+--rw nat
+--rw instances
+--rw instance* [id]
+--rw id uint32
+--rw name? string
+--rw enable? boolean
+--ro capabilities
| +--ro nat-flavor*
| | identityref
| +--ro per-interface-binding*
| | enumeration
| +--ro transport-protocols* [protocol-id]
| | +--ro protocol-id uint8
| | +--ro protocol-name? string
| +--ro restricted-port-support?
| | boolean
| +--ro static-mapping-support?
| | boolean
| +--ro port-randomization-support?
| | boolean
| +--ro port-range-allocation-support?
| | boolean
| +--ro port-preservation-suport?
| | boolean
| +--ro port-parity-preservation-support?
| | boolean
| +--ro address-roundrobin-support?
| | boolean
| +--ro paired-address-pooling-support?
| | boolean
| +--ro endpoint-independent-mapping-support?
| | boolean
| +--ro address-dependent-mapping-support?
| | boolean
| +--ro address-and-port-dependent-mapping-support?
| | boolean
| +--ro endpoint-independent-filtering-support?
| | boolean
| +--ro address-dependent-filtering?
| | boolean
| +--ro address-and-port-dependent-filtering?
| | boolean
| +--ro fragment-behavior?
| enumeration
+--rw type? identityref
+--rw per-interface-binding? enumeration
+--rw nat-pass-through* [id]
| {basic-nat44 or napt44 or dst-nat}?
| +--rw id uint32
| +--rw prefix inet:ip-prefix
| +--rw port? inet:port-number
+--rw policy* [id]
| +--rw id uint32
| +--rw clat-parameters {clat}?
| | +--rw clat-ipv6-prefixes* [ipv6-prefix]
| | | +--rw ipv6-prefix inet:ipv6-prefix
| | +--rw ipv4-prefixes* [ipv4-prefix]
| | +--rw ipv4-prefix inet:ipv4-prefix
| +--rw nptv6-prefixes* [internal-ipv6-prefix] {nptv6}?
| | +--rw internal-ipv6-prefix inet:ipv6-prefix
| | +--rw external-ipv6-prefix inet:ipv6-prefix
| +--rw eam* [ipv4-prefix] {eam}?
| | +--rw ipv4-prefix inet:ipv4-prefix
| | +--rw ipv6-prefix inet:ipv6-prefix
| +--rw nat64-prefixes* [nat64-prefix]
| | {siit or nat64 or clat}?
| | +--rw nat64-prefix inet:ipv6-prefix
| | +--rw destination-ipv4-prefix* [ipv4-prefix]
| | | +--rw ipv4-prefix inet:ipv4-prefix
| | +--rw stateless-enable? boolean
| +--rw external-ip-address-pool* [pool-id]
| | {basic-nat44 or napt44 or nat64}?
| | +--rw pool-id uint32
| | +--rw external-ip-pool inet:ipv4-prefix
| +--rw port-set-restrict {napt44 or nat64}?
| | +--rw (port-type)?
| | +--:(port-range)
| | | +--rw start-port-number? inet:port-number
| | | +--rw end-port-number? inet:port-number
| | +--:(port-set-algo)
| | +--rw psid-offset? uint8
| | +--rw psid-len uint8
| | +--rw psid uint16
| +--rw dst-nat-enable? boolean
| | {basic-nat44 or napt44}?
| +--rw dst-ip-address-pool* [pool-id] {dst-nat}?
| | +--rw pool-id uint32
| | +--rw dst-in-ip-pool? inet:ip-prefix
| | +--rw dst-out-ip-pool inet:ip-prefix
| +--rw transport-protocols* [protocol-id]
| | {napt44 or nat64 or dst-nat}?
| | +--rw protocol-id uint8
| | +--rw protocol-name? string
| +--rw subscriber-mask-v6? uint8
| +--rw subscriber-match* [match-id]
| | {basic-nat44 or napt44 or dst-nat}?
| | +--rw match-id uint32
| | +--rw subnet inet:ip-prefix
| +--rw address-allocation-type? enumeration
| +--rw port-allocation-type? enumeration
| | {napt44 or nat64}?
| +--rw mapping-type? enumeration
| | {napt44 or nat64}?
| +--rw filtering-type? enumeration
| | {napt44 or nat64}?
| +--rw fragment-behavior? enumeration
| | {napt44 or nat64}?
| +--rw port-quota* [quota-type] {napt44 or nat64}?
| | +--rw port-limit? uint16
| | +--rw quota-type uint8
| +--rw port-set {napt44 or nat64}?
| | +--rw port-set-size uint16
| | +--rw port-set-timeout? uint32
| +--rw timers {napt44 or nat64}?
| | +--rw udp-timeout? uint32
| | +--rw tcp-idle-timeout? uint32
| | +--rw tcp-trans-open-timeout? uint32
| | +--rw tcp-trans-close-timeout? uint32
| | +--rw tcp-in-syn-timeout? uint32
| | +--rw fragment-min-timeout? uint32
| | +--rw icmp-timeout? uint32
| | +--rw per-port-timeout* [port-number]
| | | +--rw port-number inet:port-number
| | | +--rw protocol? uint32
| | | +--rw timeout uint32
| | +--rw hold-down-timeout? uint32
| | +--rw hold-down-max? uint32
| +--rw fragments-limit? uint32
| +--rw algs* [name]
| | +--rw name string
| | +--rw transport-protocol? uint32
| | +--rw dst-transport-port
| | | +--rw start-port-number? inet:port-number
| | | +--rw end-port-number? inet:port-number
| | +--rw src-transport-port
| | | +--rw start-port-number? inet:port-number
| | | +--rw end-port-number? inet:port-number
| | +--rw status? boolean
| +--rw all-algs-enable? boolean
| +--rw notify-pool-usage
| | {basic-nat44 or napt44 or nat64}?
| | +--rw pool-id? uint32
| | +--rw high-threshold? percent
| | +--rw low-threshold? percent
| | +--rw notify-interval? uint32
| +--rw external-realm
| +--rw (realm-type)?
| +--:(interface)
| +--rw external-interface? if:interface-ref
+--rw mapping-limits {napt44 or nat64}?
| +--rw limit-subscribers? uint32
| +--rw limit-address-mappings? uint32
| +--rw limit-port-mappings? uint32
| +--rw limit-per-protocol* [protocol-id]
| {napt44 or nat64 or dst-nat}?
| +--rw protocol-id uint8
| +--rw limit? uint32
+--rw connection-limits
| {basic-nat44 or napt44 or nat64}?
| +--rw limit-per-subscriber? uint32
| +--rw limit-per-instance? uint32
| +--rw limit-per-protocol* [protocol-id]
| {napt44 or nat64}?
| +--rw protocol-id uint8
| +--rw limit? uint32
+--rw notification-limits
| +--rw notify-interval? uint32
| | {basic-nat44 or napt44 or nat64}?
| +--rw notify-addresses-usage? percent
| | {basic-nat44 or napt44 or nat64}?
| +--rw notify-ports-usage? percent
| | {napt44 or nat64}?
| +--rw notify-subscribers-limit? uint32
| {basic-nat44 or napt44 or nat64}?
+--rw mapping-table
| |{basic-nat44 or napt44 or nat64 or clat or dst-nat}?
| +--rw mapping-entry* [index]
| +--rw index uint32
| +--rw type? enumeration
| +--rw transport-protocol? uint8
| +--rw internal-src-address? inet:ip-prefix
| +--rw internal-src-port
| | +--rw start-port-number? inet:port-number
| | +--rw end-port-number? inet:port-number
| +--rw external-src-address? inet:ip-prefix
| +--rw external-src-port
| | +--rw start-port-number? inet:port-number
| | +--rw end-port-number? inet:port-number
| +--rw internal-dst-address? inet:ip-prefix
| +--rw internal-dst-port
| | +--rw start-port-number? inet:port-number
| | +--rw end-port-number? inet:port-number
| +--rw external-dst-address? inet:ip-prefix
| +--rw external-dst-port
| | +--rw start-port-number? inet:port-number
| | +--rw end-port-number? inet:port-number
| +--rw lifetime? uint32
+--ro statistics
+--ro discontinuity-time yang:date-and-time
+--ro traffic-statistics
| +--ro sent-packets?
| | yang:zero-based-counter64
| +--ro sent-bytes?
| | yang:zero-based-counter64
| +--ro rcvd-packets?
| | yang:zero-based-counter64
| +--ro rcvd-bytes?
| | yang:zero-based-counter64
| +--ro dropped-packets?
| | yang:zero-based-counter64
| +--ro dropped-bytes?
| | yang:zero-based-counter64
| +--ro dropped-fragments?
| | yang:zero-based-counter64
| | {napt44 or nat64}?
| +--ro dropped-address-limit-packets?
| | yang:zero-based-counter64
| | {basic-nat44 or napt44 or nat64}?
| +--ro dropped-address-limit-bytes?
| | yang:zero-based-counter64
| | {basic-nat44 or napt44 or nat64}?
| +--ro dropped-address-packets?
| | yang:zero-based-counter64
| | {basic-nat44 or napt44 or nat64}?
| +--ro dropped-address-bytes?
| | yang:zero-based-counter64
| | {basic-nat44 or napt44 or nat64}?
| +--ro dropped-port-limit-packets?
| | yang:zero-based-counter64
| | {napt44 or nat64}?
| +--ro dropped-port-limit-bytes?
| | yang:zero-based-counter64
| | {napt44 or nat64}?
| +--ro dropped-port-packets?
| | yang:zero-based-counter64
| | {napt44 or nat64}?
| +--ro dropped-port-bytes?
| | yang:zero-based-counter64
| | {napt44 or nat64}?
| +--ro dropped-subscriber-limit-packets?
| | yang:zero-based-counter64
| | {basic-nat44 or napt44 or nat64}?
| +--ro dropped-subscriber-limit-bytes?
| yang:zero-based-counter64
| {basic-nat44 or napt44 or nat64}?
+--ro mappings-statistics
| +--ro total-active-subscribers? yang:gauge32
| | {basic-nat44 or napt44 or nat64}?
| +--ro total-address-mappings? yang:gauge32
| |{basic-nat44 or napt44 or nat64 or clat or dst-nat}?
| +--ro total-port-mappings? yang:gauge32
| | {napt44 or nat64}?
| +--ro total-per-protocol* [protocol-id]
| {napt44 or nat64}?
| +--ro protocol-id uint8
| +--ro total? yang:gauge32
+--ro pools-stats {basic-nat44 or napt44 or nat64}?
+--ro addresses-allocated? yang:gauge32
+--ro addresses-free? yang:gauge32
+--ro ports-stats {napt44 or nat64}?
| +--ro ports-allocated? yang:gauge32
| +--ro ports-free? yang:gauge32
+--ro per-pool-stats* [pool-id]
{basic-nat44 or napt44 or nat64}?
+--ro pool-id uint32
+--ro discontinuity-time yang:date-and-time
+--ro pool-stats
| +--ro addresses-allocated? yang:gauge32
| +--ro addresses-free? yang:gauge32
+--ro port-stats {napt44 or nat64}?
+--ro ports-allocated? yang:gauge32
+--ro ports-free? yang:gauge32
notifications:
+---n nat-pool-event {basic-nat44 or napt44 or nat64}?
| +--ro id -> /nat/instances/instance/id
| +--ro policy-id?
| | -> /nat/instances/instance/policy/id
| +--ro pool-id leafref
| +--ro notify-pool-threshold percent
+---n nat-instance-event {basic-nat44 or napt44 or nat64}?
+--ro id
| -> /nat/instances/instance/id
+--ro notify-subscribers-threshold? uint32
+--ro notify-addresses-threshold? percent
+--ro notify-ports-threshold? percent
<CODE BEGINS> file "ietf-nat@2018-06-28.yang"
module ietf-nat {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-nat";
prefix "nat";
import ietf-inet-types {
prefix inet;
reference
"Section 4 of RFC 6991";
}
import ietf-yang-types {
prefix yang;
reference
"Section 3 of RFC 6991";
}
import ietf-interfaces {
prefix if;
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
organization
"IETF OPSAWG (Operations and Management Area Working Group)";
contact
"WG Web: <https://datatracker.ietf.org/wg/opsawg/>
WG List: <mailto:opsawg@ietf.org>
Editor: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Author: Senthil Sivakumar
<mailto:ssenthil@cisco.com>
Author: Christian Jacquenet
<mailto:christian.jacquenet@orange.com>
Author: Suresh Vinapamula
<mailto:sureshk@juniper.net>
Author: Qin Wu
<mailto:bill.wu@huawei.com>";
description
"This module is a YANG module for NAT implementations.
NAT44, Network Address and Protocol Translation from IPv6
Clients to IPv4 Servers (NAT64), Customer-side transLATor (CLAT),
Stateless IP/ICMP Translation (SIIT), Explicit Address Mappings
for Stateless IP/ICMP Translation (SIIT EAM), IPv6 Network
Prefix Translation (NPTv6), and Destination NAT are covered.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-06-28 {
description
"Initial revision.";
reference
"RFC XXXX: A YANG Module for Network Address Translation
(NAT) and Network Prefix Translation (NPT)";
}
/*
* Definitions
*/
typedef percent {
type uint8 {
range "0 .. 100";
}
description
"Percentage";
}
/*
* Features
*/
feature basic-nat44{
description
"Basic NAT44 translation is limited to IP addresses alone.";
reference
"RFC 3022: Traditional IP Network Address Translator
(Traditional NAT)";
}
feature napt44 {
description
"Network Address/Port Translator (NAPT): translation is
extended to include IP addresses and transport identifiers
(such as a TCP/UDP port or ICMP query ID).
If the internal IP address is not sufficient to uniquely
disambiguate NAPT44 mappings, an additional attribute is
required. For example, that additional attribute may
be an IPv6 address (a.k.a., DS-Lite) or
a Layer 2 identifier (a.k.a., Per-Interface NAT)";
reference
"RFC 3022: Traditional IP Network Address Translator
(Traditional NAT)";
}
feature dst-nat {
description
"Destination NAT is a translation that acts on the destination
IP address and/or destination port number. This flavor is
usually deployed in load balancers or at devices
in front of public servers.";
}
feature nat64 {
description
"NAT64 translation allows IPv6-only clients to contact IPv4
servers using, e.g., UDP, TCP, or ICMP. One or more
public IPv4 addresses assigned to a NAT64 translator are
shared among several IPv6-only clients.";
reference
"RFC 6146: Stateful NAT64: Network Address and Protocol
Translation from IPv6 Clients to IPv4 Servers";
}
feature siit {
description
"The Stateless IP/ICMP Translation Algorithm (SIIT), which
translates between IPv4 and IPv6 packet headers (including
ICMP headers).
In the stateless mode, an IP/ICMP translator converts IPv4
addresses to IPv6 and vice versa solely based on the
configuration of the stateless IP/ICMP translator and
information contained within the packet being translated.
The translator must support the stateless address mapping
algorithm defined in RFC6052, which is the default behavior.";
reference
"RFC 7915: IP/ICMP Translation Algorithm";
}
feature clat {
description
"CLAT is customer-side translator that algorithmically
translates 1:1 private IPv4 addresses to global IPv6 addresses,
and vice versa.
When a dedicated /64 prefix is not available for translation
from DHCPv6-PD, the CLAT may perform NAT44 for all IPv4 LAN
packets so that all the LAN-originated IPv4 packets appear
from a single IPv4 address and are then statelessly translated
to one interface IPv6 address that is claimed by the CLAT via
the Neighbor Discovery Protocol (NDP) and defended with
Duplicate Address Detection.";
reference
"RFC 6877: 464XLAT: Combination of Stateful and Stateless
Translation";
}
feature eam {
description
"Explicit Address Mapping (EAM) is a bidirectional coupling
between an IPv4 Prefix and an IPv6 Prefix.";
reference
"RFC 7757: Explicit Address Mappings for Stateless IP/ICMP
Translation";
}
feature nptv6 {
description
"NPTv6 is a stateless transport-agnostic IPv6-to-IPv6
prefix translation.";
reference
"RFC 6296: IPv6-to-IPv6 Network Prefix Translation";
}
/*
* Identities
*/
identity nat-type {
description
"Base identity for nat type.";
}
identity basic-nat44 {
base nat:nat-type;
description
"Identity for Basic NAT support.";
reference
"RFC 3022: Traditional IP Network Address Translator
(Traditional NAT)";
}
identity napt44 {
base nat:nat-type;
description
"Identity for NAPT support.";
reference
"RFC 3022: Traditional IP Network Address Translator
(Traditional NAT)";
}
identity dst-nat {
base nat:nat-type;
description
"Identity for Destination NAT support.";
}
identity nat64 {
base nat:nat-type;
description
"Identity for NAT64 support.";
reference
"RFC 6146: Stateful NAT64: Network Address and Protocol
Translation from IPv6 Clients to IPv4 Servers";
}
identity siit {
base nat:nat-type;
description
"Identity for SIIT support.";
reference
"RFC 7915: IP/ICMP Translation Algorithm";
}
identity clat {
base nat:nat-type;
description
"Identity for CLAT support.";
reference
"RFC 6877: 464XLAT: Combination of Stateful and Stateless
Translation";
}
identity eam {
base nat:nat-type;
description
"Identity for EAM support.";
reference
"RFC 7757: Explicit Address Mappings for Stateless IP/ICMP
Translation";
}
identity nptv6 {
base nat:nat-type;
description
"Identity for NPTv6 support.";
reference
"RFC 6296: IPv6-to-IPv6 Network Prefix Translation";
}
/*
* Grouping
*/
grouping port-number {
description
"Individual port or a range of ports.
When only start-port-number is present,
it represents a single port number.";
leaf start-port-number {
type inet:port-number;
description
"Beginning of the port range.";
reference
"Section 3.2.9 of RFC 8045.";
}
leaf end-port-number {
type inet:port-number;
must ". >= ../start-port-number"
{
error-message
"The end-port-number must be greater than or
equal to start-port-number.";
}
description
"End of the port range.";
reference
"Section 3.2.10 of RFC 8045.";
}
}
grouping port-set {
description
"Indicates a set of ports.
It may be a simple port range, or use the Port Set ID (PSID)
algorithm to represent a range of transport layer
ports which will be used by a NAPT.";
choice port-type {
default port-range;
description
"Port type: port-range or port-set-algo.";
case port-range {
uses port-number;
}
case port-set-algo {
leaf psid-offset {
type uint8 {
range 0..15;
}
description
"The number of offset bits (a.k.a., 'a' bits).
Specifies the numeric value for the excluded port
range/offset bits.
Allowed values are between 0 and 15 ";
reference
"Section 5.1 of RFC 7597";
}
leaf psid-len {
type uint8 {
range 0..15;
}
mandatory true;
description
"The length of PSID, representing the sharing
ratio for an IPv4 address.
(also known as 'k').
The address-sharing ratio would be 2^k.";
reference
"Section 5.1 of RFC 7597";
}
leaf psid {
type uint16;
mandatory true;
description
"Port Set Identifier (PSID) value, which
identifies a set of ports algorithmically.";
reference
"Section 5.1 of RFC 7597";
}
}
reference
"Section 7597: Mapping of Address and Port with
Encapsulation (MAP-E)";
}
}
grouping mapping-entry {
description
"NAT mapping entry.
If an attribute is not stored in the mapping/session table,
this means the corresponding fields of a packet that
matches this entry is not rewritten by the NAT or this
information is not required for NAT filtering purposes.";
leaf index {
type uint32;
description
"A unique identifier of a mapping entry. This identifier can be
automatically assigned by the NAT instance or be explicitly
configured.";
}
leaf type {
type enumeration {
enum "static" {
description
"The mapping entry is explicitly configured
(e.g., via command-line interface).";
}
enum "dynamic-implicit" {
description
"This mapping is created implicitly as a side effect
of processing a packet that requires a new mapping.";
}
enum "dynamic-explicit" {
description
"This mapping is created as a result of an explicit
request, e.g., a PCP message.";
}
}
description
"Indicates the type of a mapping entry. E.g.,
a mapping can be: static, implicit dynamic
or explicit dynamic.";
}
leaf transport-protocol {
type uint8;
description
"Upper-layer protocol associated with this mapping.
Values are taken from the IANA protocol registry.
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.
If this leaf is not instantiated, then the mapping
applies to any protocol.";
}
leaf internal-src-address {
type inet:ip-prefix;
description
"Corresponds to the source IPv4/IPv6 address/prefix
of the packet received on an internal
interface.";
}
container internal-src-port {
description
"Corresponds to the source port of the packet received
on an internal interface.
It is used also to indicate the internal source ICMP
identifier.
As a reminder, all the ICMP Query messages contain
an 'Identifier' field, which is referred to in this
document as the 'ICMP Identifier'.";
uses port-number;
}
leaf external-src-address {
type inet:ip-prefix;
description
"Source IP address/prefix of the packet sent on an
external interface of the NAT.";
}
container external-src-port {
description
"Source port of the packet sent on an external
interface of the NAT.
It is used also to indicate the external source ICMP
identifier.";
uses port-number;
}
leaf internal-dst-address {
type inet:ip-prefix;
description
"Corresponds to the destination IP address/prefix
of the packet received on an internal interface
of the NAT.
For example, some NAT implementations support
the translation of both source and destination
addresses and ports, sometimes referred to
as 'Twice NAT'.";
}
container internal-dst-port {
description
"Corresponds to the destination port of the
IP packet received on the internal interface.
It is used also to include the internal
destination ICMP identifier.";
uses port-number;
}
leaf external-dst-address {
type inet:ip-prefix;
description
"Corresponds to the destination IP address/prefix
of the packet sent on an external interface
of the NAT.";
}
container external-dst-port {
description
"Corresponds to the destination port number of
the packet sent on the external interface
of the NAT.
It is used also to include the external
destination ICMP identifier.";
uses port-number;
}
leaf lifetime {
type uint32;
units "seconds";
description
"When specified, it is used to track the connection that is
fully-formed (e.g., once the three-way handshake
TCP is completed) or the duration for maintaining
an explicit mapping alive. The mapping entry will be
removed by the NAT instance once this lifetime is expired.
When reported in a get operation, the lifetime indicates
the remaining validity lifetime.
Static mappings may not be associated with a
lifetime. If no lifetime is associated with a
static mapping, an explicit action is required to
remove that mapping.";
}
}
/*
* NAT Module
*/
container nat {
description
"NAT module";
container instances {
description
"NAT instances";
list instance {
key "id";
description
"A NAT instance. This identifier can be automatically assigned
or explicitly configured.";
leaf id {
type uint32;
must ". >= 1";
description
"NAT instance identifier.
The identifier must be greater than zero.";
reference
"RFC 7659: Definitions of Managed Objects for Network
Address Translators (NATs)";
}
leaf name {
type string;
description
"A name associated with the NAT instance.";
reference
"RFC 7659: Definitions of Managed Objects for Network
Address Translators (NATs)";
}
leaf enable {
type boolean;
description
"Status of the NAT instance.";
}
container capabilities {
config false;
description
"NAT capabilities";
leaf-list nat-flavor {
type identityref {
base nat-type;
}
description
"Supported translation type(s).";
}
leaf-list per-interface-binding {
type enumeration {
enum "unsupported" {
description
"No capability to associate a NAT binding with
an extra identifier.";
}
enum "layer-2" {
description
"The NAT instance is able to associate a mapping with
a layer-2 identifier.";
}
enum "dslite" {
description
"The NAT instance is able to associate a mapping with
an IPv6 address (a.k.a., DS-Lite).";
}
}
description
"Indicates the capability of a NAT to associate a particular
NAT session not only with the five tuples used for the
transport connection on both sides of the NAT but also with
the internal interface on which the user device is
connected to the NAT.";
reference
"Section 4 of RFC 6619";
}
list transport-protocols {
key protocol-id;
description
"List of supported protocols.";
leaf protocol-id {
type uint8;
mandatory true;
description
"Upper-layer protocol associated with a mapping.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.";
}
leaf protocol-name {
type string;
description
"The name of the Upper-layer protocol associated
with this mapping.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, TCP, UDP, DCCP, and SCTP.";
}
}
leaf restricted-port-support {
type boolean;
description
"Indicates source port NAT restriction support.";
reference
"RFC 7596: Lightweight 4over6: An Extension to
the Dual-Stack Lite Architecture.";
}
leaf static-mapping-support {
type boolean;
description
"Indicates whether static mappings are supported.";
}
leaf port-randomization-support {
type boolean;
description
"Indicates whether port randomization is supported.";
reference
"Section 4.2.1 of RFC 4787.";
}
leaf port-range-allocation-support {
type boolean;
description
"Indicates whether port range allocation is supported.";
reference
"Section 1.1 of RFC 7753.";
}
leaf port-preservation-suport {
type boolean;
description
"Indicates whether port preservation is supported.";
reference
"Section 4.2.1 of RFC 4787.";
}
leaf port-parity-preservation-support {
type boolean;
description
"Indicates whether port parity preservation is
supported.";
reference
"Section 8 of RFC 7857.";
}
leaf address-roundrobin-support {
type boolean;
description
"Indicates whether address allocation round robin is
supported.";
}
leaf paired-address-pooling-support {
type boolean;
description
"Indicates whether paired-address-pooling is
supported";
reference
"REQ-2 of RFC 4787.";
}
leaf endpoint-independent-mapping-support {
type boolean;
description
"Indicates whether endpoint-independent-
mapping is supported.";
reference
"Section 4 of RFC 4787.";
}
leaf address-dependent-mapping-support {
type boolean;
description
"Indicates whether address-dependent-mapping is
supported.";
reference
"Section 4 of RFC 4787.";
}
leaf address-and-port-dependent-mapping-support {
type boolean;
description
"Indicates whether address-and-port-dependent-mapping is
supported.";
reference
"Section 4 of RFC 4787.";
}
leaf endpoint-independent-filtering-support {
type boolean;
description
"Indicates whether endpoint-independent-filtering is
supported.";
reference
"Section 5 of RFC 4787.";
}
leaf address-dependent-filtering {
type boolean;
description
"Indicates whether address-dependent-filtering is
supported.";
reference
"Section 5 of RFC 4787.";
}
leaf address-and-port-dependent-filtering {
type boolean;
description
"Indicates whether address-and-port-dependent is
supported.";
reference
"Section 5 of RFC 4787.";
}
leaf fragment-behavior {
type enumeration {
enum "unsupported" {
description
"No capability to translate incoming fragments.
All received fragments are dropped.";
}
enum "in-order" {
description
"The NAT instance is able to translate fragments only if
they are received in order. That is, in particular the
header is in the first packet. Fragments received
out of order are dropped. ";
}
enum "out-of-order" {
description
"The NAT instance is able to translate a fragment even
if it is received out of order.
This behavior is recommended.";
reference
"REQ-14 of RFC 4787";
}
}
description
"The fragment behavior is the NAT instance's capability to
translate fragments received on the external interface of
the NAT.";
}
}
leaf type {
type identityref {
base nat-type;
}
description
"Specify the translation type. Particularly useful when
multiple translation flavors are supported.
If one type is supported by a NAT, this parameter is by
default set to that type.";
}
leaf per-interface-binding {
type enumeration {
enum "disabled" {
description
"Disable the capability to associate an extra identifier
with NAT mappings.";
}
enum "layer-2" {
description
"The NAT instance is able to associate a mapping with
a layer-2 identifier.";
}
enum "dslite" {
description
"The NAT instance is able to associate a mapping with
an IPv6 address (a.k.a., DS-Lite).";
}
}
description
"A NAT that associates a particular NAT session not only with
the five tuples used for the transport connection on both
sides of the NAT but also with the internal interface on
which the user device is connected to the NAT.
If supported, this mode of operation should be configurable,
and it should be disabled by default in general-purpose NAT
devices.
If one single per-interface binding behavior is supported by
a NAT, this parameter is by default set to that behavior.";
reference
"Section 4 of RFC 6619";
}
list nat-pass-through {
if-feature "basic-nat44 or napt44 or dst-nat";
key id;
description
"IP prefix NAT pass through.";
leaf id {
type uint32;
description
"An identifier of the IP prefix pass through.";
}
leaf prefix {
type inet:ip-prefix;
mandatory true;
description
"The IP addresses that match should not be translated.
It must be possible to administratively turn
off translation for specific destination addresses
and/or ports.";
reference
"REQ#6 of RFC 6888.";
}
leaf port {
type inet:port-number;
description
"It must be possible to administratively turn off
translation for specific destination addresses
and/or ports.
If no prefix is defined, the NAT pass through bound
to a given port applies for any destination address.";
reference
"REQ#6 of RFC 6888.";
}
}
list policy {
key id;
description
"NAT parameters for a given instance";
leaf id {
type uint32;
description
"An identifier of the NAT policy. It must be unique
within the NAT instance.";
}
container clat-parameters {
if-feature clat;
description
"CLAT parameters.";
list clat-ipv6-prefixes {
key ipv6-prefix;
description
"464XLAT double translation treatment is stateless when a
dedicated /64 is available for translation on the CLAT.
Otherwise, the CLAT will have both stateful and stateless
since it requires NAT44 from the LAN to a single IPv4
address and then stateless translation to a single
IPv6 address.";
reference
"RFC 6877: 464XLAT: Combination of Stateful and Stateless
Translation";
leaf ipv6-prefix {
type inet:ipv6-prefix;
description
"An IPv6 prefix used for CLAT.";
}
}
list ipv4-prefixes {
key ipv4-prefix;
description
"Pool of IPv4 addresses used for CLAT.
192.0.0.0/29 is the IPv4 service continuity prefix.";
reference
"RFC 7335: IPv4 Service Continuity Prefix";
leaf ipv4-prefix {
type inet:ipv4-prefix;
description
"464XLAT double translation treatment is
stateless when a dedicated /64 is available
for translation on the CLAT. Otherwise, the
CLAT will have both stateful and stateless
since it requires NAT44 from the LAN to
a single IPv4 address and then stateless
translation to a single IPv6 address.
The CLAT performs NAT44 for all IPv4 LAN
packets so that all the LAN-originated IPv4
packets appear from a single IPv4 address
and are then statelessly translated to one
interface IPv6 address that is claimed by
the CLAT.
An IPv4 address from this pool is also
provided to an application that makes
use of literals.";
reference
"RFC 6877: 464XLAT: Combination of Stateful and Stateless
Translation";
}
}
}
list nptv6-prefixes {
if-feature nptv6;
key internal-ipv6-prefix ;
description
"Provides one or a list of (internal IPv6 prefix,
external IPv6 prefix) required for NPTv6.
In its simplest form, NPTv6 interconnects two network
links, one of which is an 'internal' network link
attached to a leaf network within a single
administrative domain and the other of which is an
'external' network with connectivity to the global
Internet.";
reference
"RFC 6296: IPv6-to-IPv6 Network Prefix Translation";
leaf internal-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"An IPv6 prefix used by an internal interface of NPTv6.";
reference
"RFC 6296: IPv6-to-IPv6 Network Prefix Translation";
}
leaf external-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"An IPv6 prefix used by the external interface of NPTv6.";
reference
"RFC 6296: IPv6-to-IPv6 Network Prefix Translation";
}
}
list eam {
if-feature eam;
key ipv4-prefix;
description
"The Explicit Address Mapping Table, a conceptual
table in which each row represents an EAM.
Each EAM describes a mapping between IPv4 and IPv6
prefixes/addresses.";
reference
"Section 3.1 of RFC 7757.";
leaf ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"The IPv4 prefix of an EAM.";
reference
"Section 3.2 of RFC 7757.";
}
leaf ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"The IPv6 prefix of an EAM.";
reference
"Section 3.2 of RFC 7757.";
}
}
list nat64-prefixes {
if-feature "siit or nat64 or clat";
key nat64-prefix;
description
"Provides one or a list of NAT64 prefixes
with or without a list of destination IPv4 prefixes.
It allows mapping IPv4 address ranges to IPv6 prefixes.
For example:
192.0.2.0/24 is mapped to 2001:db8:122:300::/56.
198.51.100.0/24 is mapped to 2001:db8:122::/48.";
reference
"Section 5.1 of RFC 7050.";
leaf nat64-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"A NAT64 prefix. Can be Network-Specific Prefix (NSP) or
Well-Known Prefix (WKP).
Organizations deploying stateless IPv4/IPv6 translation
should assign a Network-Specific Prefix to their
IPv4/IPv6 translation service.
For stateless NAT64, IPv4-translatable IPv6 addresses
must use the selected Network-Specific Prefix.
Both IPv4-translatable IPv6 addresses and IPv4-converted
IPv6 addresses should use the same prefix.";
reference
"Sections 3.3 and 3.4 of RFC 6052.";
}
list destination-ipv4-prefix {
key ipv4-prefix;
description
"An IPv4 prefix/address.";
leaf ipv4-prefix {
type inet:ipv4-prefix;
description
"An IPv4 address/prefix.";
}
}
leaf stateless-enable {
type boolean;
default false;
description
"Enable explicitly stateless NAT64.";
}
}
list external-ip-address-pool {
if-feature "basic-nat44 or napt44 or nat64";
key pool-id;
description
"Pool of external IP addresses used to service internal
hosts.
A pool is a set of IP prefixes.";
leaf pool-id {
type uint32;
must ". >= 1";
description
"An identifier that uniquely identifies the address pool
within a NAT instance.
The identifier must be greater than zero.";
reference
"RFC 7659: Definitions of Managed Objects for
Network Address Translators (NATs)";
}
leaf external-ip-pool {
type inet:ipv4-prefix;
mandatory true;
description
"An IPv4 prefix used for NAT purposes.";
}
}
container port-set-restrict {
if-feature "napt44 or nat64";
description
"Configures contiguous and non-contiguous port ranges.
The port set is used to restrict the external source
port numbers used by the translator.";
uses port-set;
}
leaf dst-nat-enable {
if-feature "basic-nat44 or napt44";
type boolean;
default false;
description
"Enable/Disable destination NAT.
A NAT44 may be configured to enable Destination
NAT, too.";
}
list dst-ip-address-pool {
if-feature dst-nat;
key pool-id;
description
"Pool of IP addresses used for destination NAT.";
leaf pool-id {
type uint32;
description
"An identifier of the address pool.";
}
leaf dst-in-ip-pool {
type inet:ip-prefix;
description
"Is used to identify an internal destination
IP prefix/address to be translated.";
}
leaf dst-out-ip-pool {
type inet:ip-prefix;
mandatory true;
description
"IP address/prefix used for destination NAT.";
}
}
list transport-protocols {
if-feature "napt44 or nat64 or dst-nat";
key protocol-id;
description
"Configure the transport protocols to be handled by
the translator.
TCP and UDP are supported by default.";
leaf protocol-id {
type uint8;
mandatory true;
description
"Upper-layer protocol associated with this mapping.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.";
}
leaf protocol-name {
type string;
description
"The name of the Upper-layer protocol associated
with this mapping.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, TCP, UDP, DCCP, and SCTP.";
}
}
leaf subscriber-mask-v6 {
type uint8 {
range "0 .. 128";
}
description
"The subscriber mask is an integer that indicates
the length of significant bits to be applied on
the source IPv6 address (internal side) to
unambiguously identify a user device (e.g., CPE).
Subscriber mask is a system-wide configuration
parameter that is used to enforce generic
per-subscriber policies (e.g., port-quota).
The enforcement of these generic policies does not
require the configuration of every subscriber's
prefix.
Example: suppose the 2001:db8:100:100::/56 prefix
is assigned to a NAT64 serviced CPE. Suppose also
that 2001:db8:100:100::1 is the IPv6 address used
by the client that resides in that CPE. When the
NAT64 receives a packet from this client,
it applies the subscriber-mask-v6 (e.g., 56) on
the source IPv6 address to compute the associated
prefix for this client (2001:db8:100:100::/56).
Then, the NAT64 enforces policies based on that
prefix (2001:db8:100:100::/56), not on the exact
source IPv6 address.";
}
list subscriber-match {
if-feature "basic-nat44 or napt44 or dst-nat";
key match-id;
description
"IP prefix match.
A subscriber is identified by a subnet.";
leaf match-id {
type uint32;
description
"An identifier of the subscriber match.";
}
leaf subnet {
type inet:ip-prefix;
mandatory true;
description
"The IP address subnets that match
should be translated. E.g., all addresses
that belong to the 192.0.2.0/24 prefix must
be processed by the NAT.";
}
}
leaf address-allocation-type {
type enumeration {
enum "arbitrary" {
if-feature "basic-nat44 or napt44 or nat64";
description
"Arbitrary pooling behavior means that the NAT
instance may create the new port mapping using any
address in the pool that has a free port for the
protocol concerned.";
}
enum "roundrobin" {
if-feature "basic-nat44 or napt44 or nat64";
description
"Round robin allocation.";
}
enum "paired" {
if-feature "napt44 or nat64";
description
"Paired address pooling informs the NAT
that all the flows from an internal IP
address must be assigned the same external
address. This is the recommended behavior for
NAPT/NAT64.";
reference
"RFC 4787: Network Address Translation (NAT)
Behavioral Requirements for Unicast UDP";
}
}
description
"Specifies how external IP addresses are allocated.";
}
leaf port-allocation-type {
if-feature "napt44 or nat64";
type enumeration {
enum "random" {
description
"Port randomization is enabled. A NAT port allocation
scheme should make it hard for attackers to guess
port numbers";
reference
"REQ-15 of RFC 6888";
}
enum "port-preservation" {
description
"Indicates whether the NAT should preserve the internal
port number.";
}
enum "port-parity-preservation" {
description
"Indicates whether the NAT should preserve the port
parity of the internal port number.";
}
enum "port-range-allocation" {
description
"Indicates whether the NAT assigns a range of ports
for an internal host. This scheme allows to minimize
log volume.";
reference
"REQ-14 of RFC 6888";
}
}
description
"Indicates the type of port allocation.";
}
leaf mapping-type {
if-feature "napt44 or nat64";
type enumeration {
enum "eim" {
description
"endpoint-independent-mapping.";
reference
"Section 4 of RFC 4787.";
}
enum "adm" {
description
"address-dependent-mapping.";
reference
"Section 4 of RFC 4787.";
}
enum "edm" {
description
"address-and-port-dependent-mapping.";
reference
"Section 4 of RFC 4787.";
}
}
description
"Indicates the type of a NAT mapping.";
}
leaf filtering-type {
if-feature "napt44 or nat64";
type enumeration {
enum "eif" {
description
"endpoint-independent-filtering.";
reference
"Section 5 of RFC 4787.";
}
enum "adf" {
description
"address-dependent-filtering.";
reference
"Section 5 of RFC 4787.";
}
enum "edf" {
description
"address-and-port-dependent-filtering";
reference
"Section 5 of RFC 4787.";
}
}
description
"Indicates the type of a NAT filtering.";
}
leaf fragment-behavior {
if-feature "napt44 or nat64";
type enumeration {
enum "drop-all" {
description
"All received fragments are dropped.";
}
enum "in-order" {
description
"Translate fragments only if they are received
in order.";
}
enum "out-of-order" {
description
"Translate a fragment even if it is received out
of order.
This behavior is recommended.";
reference
"REQ-14 of RFC 4787";
}
}
description
"The fragment behavior instructs the NAT about the
behavior to follow to translate fragments received
on the external interface of the NAT.";
}
list port-quota {
if-feature "napt44 or nat64";
key quota-type;
description
"Configures a port quota to be assigned per subscriber.
It corresponds to the maximum number of ports to be
used by a subscriber.";
leaf port-limit {
type uint16;
description
"Configures a port quota to be assigned per subscriber.
It corresponds to the maximum number of ports to be
used by a subscriber.";
reference
"REQ-4 of RFC 6888.";
}
leaf quota-type {
type uint8;
description
"Indicates whether the port quota applies to
all protocols (0) or to a specific protocol.";
}
}
container port-set {
when "../port-allocation-type = 'port-range-allocation'";
if-feature "napt44 or nat64";
description
"Manages port-set assignments.";
leaf port-set-size {
type uint16;
mandatory true;
description
"Indicates the size of assigned port sets.";
}
leaf port-set-timeout {
type uint32;
units "seconds";
description
"inactivity timeout for port sets.";
}
}
container timers {
if-feature "napt44 or nat64";
description
"Configure values of various timeouts.";
leaf udp-timeout {
type uint32;
units "seconds";
default 300;
description
"UDP inactivity timeout. That is the time a mapping
will stay active without packets traversing the NAT.";
reference
"RFC 4787: Network Address Translation (NAT)
Behavioral Requirements for Unicast UDP";
}
leaf tcp-idle-timeout {
type uint32;
units "seconds";
default 7440;
description
"TCP Idle timeout should be 2 hours and 4 minutes.";
reference
"RFC 5382: NAT Behavioral Requirements for TCP";
}
leaf tcp-trans-open-timeout {
type uint32;
units "seconds";
default 240;
description
"The value of the transitory open connection
idle-timeout.
A NAT should provide different configurable
parameters for configuring the open and
closing idle timeouts.
To accommodate deployments that consider
a partially open timeout of 4 minutes as being
excessive from a security standpoint, a NAT may
allow the configured timeout to be less than
4 minutes.
However, a minimum default transitory connection
idle-timeout of 4 minutes is recommended.";
reference
"Section 2.1 of RFC 7857.";
}
leaf tcp-trans-close-timeout {
type uint32;
units "seconds";
default 240;
description
"The value of the transitory close connection
idle-timeout.
A NAT should provide different configurable
parameters for configuring the open and
closing idle timeouts.";
reference
"Section 2.1 of RFC 7857.";
}
leaf tcp-in-syn-timeout {
type uint32;
units "seconds";
default 6;
description
"A NAT must not respond to an unsolicited
inbound SYN packet for at least 6 seconds
after the packet is received. If during
this interval the NAT receives and translates
an outbound SYN for the connection the NAT
must silently drop the original unsolicited
inbound SYN packet.";
reference
"RFC 5382 NAT Behavioral Requirements for TCP";
}
leaf fragment-min-timeout {
when "../../fragment-behavior='out-of-order'";
type uint32;
units "seconds";
default 2;
description
"As long as the NAT has available resources,
the NAT allows the fragments to arrive
over fragment-min-timeout interval.
The default value is inspired from RFC6146.";
}
leaf icmp-timeout {
type uint32;
units "seconds";
default 60;
description
"An ICMP Query session timer must not expire
in less than 60 seconds. It is recommended
that the ICMP Query session timer be made
configurable";
reference
"RFC 5508: NAT Behavioral Requirements for ICMP";
}
list per-port-timeout {
key port-number;
description
"Some NATs are configurable with short timeouts
for some ports, e.g., as 10 seconds on
port 53 (DNS) and 123 (NTP) and longer timeouts
on other ports.";
leaf port-number {
type inet:port-number;
description
"A port number.";
}
leaf protocol {
type uint8;
description
"Upper-layer protocol associated with this port.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml.
If no protocol is indicated, this means 'any
protocol'.";
}
leaf timeout {
type uint32;
units "seconds";
mandatory true;
description
"Timeout for this port number";
}
}
leaf hold-down-timeout {
type uint32;
units "seconds";
default 120;
description
"Hold down timer.
Ports in the hold down pool are not reassigned until
hold-down-timeout expires.
The length of time and the maximum number of ports in
this state must be configurable by the administrator.
This is necessary in order to prevent collisions
between old and new mappings and sessions. It ensures
that all established sessions are broken instead of
redirected to a different peer.";
reference
"REQ#8 of RFC 6888.";
}
leaf hold-down-max {
type uint32;
description
"Maximum ports in the Hold down timer pool.
Ports in the hold down pool are not reassigned
until hold-down-timeout expires.
The length of time and the maximum
number of ports in this state must be
configurable by the administrator.
This is necessary in order
to prevent collisions between old
and new mappings and sessions. It ensures
that all established sessions are broken
instead of redirected to a different peer.";
reference
"REQ#8 of RFC 6888.";
}
}
leaf fragments-limit{
when "../fragment-behavior='out-of-order'";
type uint32;
description
"Limits the number of out of order fragments that can
be handled.";
reference
"Section 11 of RFC 4787.";
}
list algs {
key name;
description
"ALG-related features.";
leaf name {
type string;
description
"The name of the ALG.";
}
leaf transport-protocol {
type uint32;
description
"The transport protocol used by the ALG
(e.g., TCP, UDP).";
}
container dst-transport-port {
uses port-number;
description
"The destination port number(s) used by the ALG.
For example,
- 21 for the FTP ALG
- 53 for the DNS ALG.";
}
container src-transport-port {
uses port-number;
description
"The source port number(s) used by the ALG.";
}
leaf status {
type boolean;
description
"Enable/disable the ALG.";
}
}
leaf all-algs-enable {
type boolean;
description
"Enable/disable all ALGs.
When specified, this parameter overrides the one
that may be indicated, eventually, by the 'status'
of an individual ALG.";
}
container notify-pool-usage {
if-feature "basic-nat44 or napt44 or nat64";
description
"Notification of pool usage when certain criteria
are met.";
leaf pool-id {
type uint32;
description
"Pool-ID for which the notification criteria
is defined";
}
leaf high-threshold {
type percent;
description
"Notification must be generated when the defined high
threshold is reached.
For example, if a notification is required when the
pool utilization reaches 90%, this configuration
parameter must be set to 90.
0% indicates that no high threshold is enabled.";
}
leaf low-threshold {
type percent;
must ". >= ../high-threshold" {
error-message
"The upper port number must be greater than or
equal to lower port number.";
}
description
"Notification must be generated when the defined low
threshold is reached.
For example, if a notification is required when the
pool utilization reaches below 10%, this
configuration parameter must be set to 10";
}
leaf notify-interval {
type uint32 {
range "1 .. 3600";
}
units "seconds";
default '20';
description
"Minimum number of seconds between successive
notifications for this pool.";
reference
"RFC 7659: Definitions of Managed Objects for
Network Address Translators (NATs)";
}
}
container external-realm {
description
"Identifies the external realm of the NAT instance.";
choice realm-type {
description
"Can be an interface, VRF instance, etc.";
case interface {
description
"External interface.";
leaf external-interface {
type if:interface-ref;
description
"Name of the external interface.";
}
}
}
}
}
container mapping-limits {
if-feature "napt44 or nat64";
description
"Information about the configuration parameters that
limits the mappings based upon various criteria.";
leaf limit-subscribers {
type uint32;
description
"Maximum number of subscribers that can be serviced
by a NAT instance.
A subscriber is identified by a given prefix.";
reference
"RFC 7659: Definitions of Managed Objects for
Network Address Translators (NATs)";
}
leaf limit-address-mappings {
type uint32;
description
"Maximum number of address mappings that can be
handled by a NAT instance.
When this limit is reached, packets that would
normally trigger translation, will be dropped.";
reference
"RFC 7659: Definitions of Managed Objects
for Network Address Translators
(NATs)";
}
leaf limit-port-mappings {
type uint32;
description
"Maximum number of port mappings that can be handled
by a NAT instance.
When this limit is reached, packets that would
normally trigger translation, will be dropped.";
reference
"RFC 7659: Definitions of Managed Objects for
Network Address Translators (NATs)";
}
list limit-per-protocol {
if-feature "napt44 or nat64 or dst-nat";
key protocol-id;
description
"Configure limits per transport protocol";
leaf protocol-id {
type uint8;
mandatory true;
description
"Upper-layer protocol.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.";
}
leaf limit {
type uint32;
description
"Maximum number of protocol-specific NAT mappings
per instance.";
}
}
}
container connection-limits {
if-feature "basic-nat44 or napt44 or nat64";
description
"Information about the configuration parameters that
rate limit the translation based upon various criteria.";
leaf limit-per-subscriber {
type uint32;
units "bits/second";
description
"Rate-limit the number of new mappings and sessions
per subscriber.";
}
leaf limit-per-instance {
type uint32;
units "bits/second";
description
"Rate-limit the number of new mappings and sessions
per instance.";
}
list limit-per-protocol {
if-feature "napt44 or nat64";
key protocol-id;
description
"Configure limits per transport protocol";
leaf protocol-id {
type uint8;
mandatory true;
description
"Upper-layer protocol.
Values are taken from the IANA protocol registry:
https://www.iana.org/assignments/protocol-numbers/
protocol-numbers.xhtml
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.";
}
leaf limit {
type uint32;
description
"Rate-limit the number of protocol-specific mappings
and sessions per instance.";
}
}
}
container notification-limits {
description "Sets notification limits.";
leaf notify-interval {
if-feature "basic-nat44 or napt44 or nat64";
type uint32 {
range "1 .. 3600";
}
units "seconds";
default '10';
description
"Minimum number of seconds between successive
notifications for this NAT instance.";
reference
"RFC 7659: Definitions of Managed Objects
for Network Address Translators (NATs)";
}
leaf notify-addresses-usage {
if-feature "basic-nat44 or napt44 or nat64";
type percent;
description
"Notification of address mappings usage over
the whole NAT instance.
Notification must be generated when the defined
threshold is reached.
For example, if a notification is required when
the address mappings utilization reaches 90%,
this configuration parameter must be set
to 90.";
}
leaf notify-ports-usage {
if-feature "napt44 or nat64";
type percent;
description
"Notification of port mappings usage over the
whole NAT instance.
Notification must be generated when the defined
threshold is reached.
For example, if a notification is required when
the port mappings utilization reaches 90%, this
configuration parameter must be set to 90.";
}
leaf notify-subscribers-limit {
if-feature "basic-nat44 or napt44 or nat64";
type uint32;
description
"Notification of active subscribers per NAT
instance.
Notification must be generated when the defined
threshold is reached.";
}
}
container mapping-table {
if-feature "basic-nat44 or napt44 " +
"or nat64 or clat or dst-nat";
description
"NAT mapping table. Applicable for functions which maintain
static and/or dynamic mappings, such as NAT44, Destination
NAT, NAT64, or CLAT.";
list mapping-entry {
key "index";
description "NAT mapping entry.";
uses mapping-entry;
}
}
container statistics {
config false;
description
"Statistics related to the NAT instance.";
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
description
"The time on the most recent occasion at which the NAT
instance suffered a discontinuity. This must be
initialized when the NAT instance is configured
or rebooted.";
}
container traffic-statistics {
description
"Generic traffic statistics.";
leaf sent-packets {
type yang:zero-based-counter64;
description
"Number of packets sent.";
}
leaf sent-bytes {
type yang:zero-based-counter64;
units 'bytes';
description
"Counter for sent traffic in bytes.";
}
leaf rcvd-packets {
type yang:zero-based-counter64;
description
"Number of received packets.";
}
leaf rcvd-bytes {
type yang:zero-based-counter64;
units 'bytes';
description
"Counter for received traffic in bytes.";
}
leaf dropped-packets {
type yang:zero-based-counter64;
description
"Number of dropped packets.";
}
leaf dropped-bytes {
type yang:zero-based-counter64;
units 'bytes';
description
"Counter for dropped traffic in bytes.";
}
leaf dropped-fragments {
if-feature "napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped fragments on the external realm.";
}
leaf dropped-address-limit-packets {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped packets because an address limit
is reached.";
}
leaf dropped-address-limit-bytes {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
units 'bytes';
description
"Counter of dropped packets because an address limit
is reached, in bytes.";
}
leaf dropped-address-packets {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped packets because no address is
available for allocation.";
}
leaf dropped-address-bytes {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
units 'bytes';
description
"Counter of dropped packets because no address is
available for allocation, in bytes.";
}
leaf dropped-port-limit-packets {
if-feature "napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped packets because a port limit
is reached.";
}
leaf dropped-port-limit-bytes {
if-feature "napt44 or nat64";
type yang:zero-based-counter64;
units 'bytes';
description
"Counter of dropped packets because a port limit
is reached, in bytes.";
}
leaf dropped-port-packets {
if-feature "napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped packets because no port is
available for allocation.";
}
leaf dropped-port-bytes {
if-feature "napt44 or nat64";
type yang:zero-based-counter64;
units 'bytes';
description
"Counter of dropped packets because no port is
available for allocation, in bytes.";
}
leaf dropped-subscriber-limit-packets {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
description
"Number of dropped packets because the subscriber
limit per instance is reached.";
}
leaf dropped-subscriber-limit-bytes {
if-feature "basic-nat44 or napt44 or nat64";
type yang:zero-based-counter64;
units 'bytes';
description
"Counter of dropped packets because the subscriber
limit per instance is reached, in bytes.";
}
}
container mappings-statistics {
description
"Mappings statistics.";
leaf total-active-subscribers {
if-feature "basic-nat44 or napt44 or nat64";
type yang:gauge32;
description
"Total number of active subscribers (that is,
subscribers for which the NAT maintains active
mappings.
A subscriber is identified by a subnet,
subscriber-mask, etc.";
}
leaf total-address-mappings {
if-feature "basic-nat44 or napt44 " +
"or nat64 or clat or dst-nat";
type yang:gauge32;
description
"Total number of address mappings present at a given
time. It includes both static and dynamic mappings.";
reference
"Section 3.3.8 of RFC 7659";
}
leaf total-port-mappings {
if-feature "napt44 or nat64";
type yang:gauge32;
description
"Total number of NAT port mappings present at
a given time. It includes both static and dynamic
mappings.";
reference
"Section 3.3.9 of RFC 7659";
}
list total-per-protocol {
if-feature "napt44 or nat64";
key protocol-id;
description
"Total mappings for each enabled/supported protocol.";
leaf protocol-id {
type uint8;
mandatory true;
description
"Upper-layer protocol.
For example, this field contains 6 for TCP,
17 for UDP, 33 for DCCP, or 132 for SCTP.";
}
leaf total {
type yang:gauge32;
description
"Total number of a protocol-specific mappings present
at a given time. The protocol is identified by
protocol-id.";
}
}
}
container pools-stats {
if-feature "basic-nat44 or napt44 or nat64";
description
"Statistics related to address/prefix pools
usage";
leaf addresses-allocated {
type yang:gauge32;
description
"Number of all allocated addresses.";
}
leaf addresses-free {
type yang:gauge32;
description
"Number of unallocated addresses of all pools at
a given time. The sum of unallocated and allocated
addresses is the total number of addresses of
the pools.";
}
container ports-stats {
if-feature "napt44 or nat64";
description
"Statistics related to port numbers usage.";
leaf ports-allocated {
type yang:gauge32;
description
"Number of allocated ports from all pools.";
}
leaf ports-free {
type yang:gauge32;
description
"Number of unallocated addresses from all pools.";
}
}
list per-pool-stats {
if-feature "basic-nat44 or napt44 or nat64";
key "pool-id";
description
"Statistics related to address/prefix pool usage";
leaf pool-id {
type uint32;
description
"Unique Identifier that represents a pool of
addresses/prefixes.";
}
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
description
"The time on the most recent occasion at which this
pool counters suffered a discontinuity. This must
be initialized when the address pool is
configured.";
}
container pool-stats {
description
"Statistics related to address/prefix pool usage";
leaf addresses-allocated {
type yang:gauge32;
description
"Number of allocated addresses from this pool.";
}
leaf addresses-free {
type yang:gauge32;
description
"Number of unallocated addresses in this pool.";
}
}
container port-stats {
if-feature "napt44 or nat64";
description
"Statistics related to port numbers usage.";
leaf ports-allocated {
type yang:gauge32;
description
"Number of allocated ports from this pool.";
}
leaf ports-free {
type yang:gauge32;
description
"Number of unallocated addresses from this pool.";
}
}
}
}
}
}
}
}
/*
* Notifications
*/
notification nat-pool-event {
if-feature "basic-nat44 or napt44 or nat64";
description
"Notifications must be generated when the defined high/low
threshold is reached. Related configuration parameters
must be provided to trigger the notifications.";
leaf id {
type leafref {
path "/nat/instances/instance/id";
}
mandatory true;
description
"NAT instance Identifier.";
}
leaf policy-id {
type leafref {
path "/nat/instances/instance/policy/id";
}
description
"Policy Identifier.";
}
leaf pool-id {
type leafref {
path "/nat/instances/instance/policy/" +
"external-ip-address-pool/pool-id";
}
mandatory true;
description
"Pool Identifier.";
}
leaf notify-pool-threshold {
type percent;
mandatory true;
description
"A threshold (high-threshold or low-threshold) has
been fired.";
}
}
notification nat-instance-event {
if-feature "basic-nat44 or napt44 or nat64";
description
"Notifications must be generated when notify-addresses-usage
and/or notify-ports-usage threshold are reached.";
leaf id {
type leafref {
path "/nat/instances/instance/id";
}
mandatory true;
description
"NAT instance Identifier.";
}
leaf notify-subscribers-threshold {
type uint32;
description
"The notify-subscribers-limit threshold has been fired.";
}
leaf notify-addresses-threshold {
type percent;
description
"The notify-addresses-usage threshold has been fired.";
}
leaf notify-ports-threshold {
type percent;
description
"The notify-ports-usage threshold has been fired.";
}
}
}
<CODE ENDS>
Security considerations related to address and prefix translation are discussed in [RFC6888], [RFC6146], [RFC6877], [RFC6296], and [RFC7757].
The YANG module defined in this document is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC5246].
The NETCONF access control model [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.
All data nodes defined in the YANG module which can be created, modified and deleted (i.e., config true, which is the default) are considered sensitive. Write operations (e.g., edit-config) applied to these data nodes without proper protection can negatively affect network operations. The NAT YANG module provides a method to set parameters to prevent a user from aggressively using NAT resources (port-quota), rate-limit connections as a guard against Denial-of-Service, or to enable notifications so that appropriate measures are enforced to anticipate traffic drops. Nevertheless, an attacker who is able to access the NAT can undertake various attacks, such as:
URI: urn:ietf:params:xml:ns:yang:ietf-nat
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
name: ietf-nat
namespace: urn:ietf:params:xml:ns:yang:ietf-nat
prefix: nat
reference: RFC XXXX
This document requests IANA to register the following URI in the "IETF XML Registry" [RFC3688]: [RFC7950].
Many thanks to Dan Wing, Tianran Zhou, Tom Petch, and Warren Kumari for the review.
Thanks to Juergen Schoenwaelder for the comments on the YANG structure and the suggestion to use NMDA. Mahesh Jethanandani provided useful comments.
Thanks to Lee Howard and Jordi Palet for the CLAT comments, Fred Baker for the NPTv6 comments, Tore Anderson for EAM SIIT review, and Kristian Poscic for the CGN review.
Special thanks to Maros Marsalek and Marek Gradzki for sharing their comments based on the FD.io implementation of this module (https://git.fd.io/hc2vpp/tree/nat/nat-api/src/main/yang).
Rajiv Asati suggested to clarify how the module applies for both stateless and stateful NAT64.
Juergen Schoenwaelder provided an early yandgoctors review. Many thanks to him.
Thanks to Roni Even, Mach Chen, Tim Chown, and Stephen Farrel for the directorates review. Igor Ryzhov identified a nit in one example.
Mirja Kuehlewind made a comment about the reuse of some TCP timers for any connection-oriented protocol.
This section provides a non-exhaustive set of examples to illustrate the use of the NAT YANG module.
Traditional NAT44 is a Basic NAT44 or NAPT that is used to share the same IPv4 address among hosts that are owned by the same subscriber. This is typically the NAT that is embedded in CPE devices.
This NAT is usually provided with one single external IPv4 address; disambiguating connections is achieved by rewriting the source port number. The XML snippet to configure the external IPv4 address in such case together with a mapping entry is depicted below:
<instances>
<instance>
<id>1</id>
<name>NAT_Subscriber_A</name>
....
<external-ip-address-pool>
<pool-id>1</pool-id>
<external-ip-pool>
198.51.100.1/32
</external-ip-pool>
</external-ip-address-pool>
....
<mapping-table>
....
<external-src-address>
198.51.100.1/32
</external-src-address>
....
</mapping-table>
</instance>
</instances>
The following shows the XML excerpt depicting a dynamic UDP mapping entry maintained by a traditional NAPT44. In reference to this example, the UDP packet received with a source IPv4 address (192.0.2.1) and source port number (1568) is translated into a UDP packet having a source IPv4 address (198.51.100.1) and source port (15000). The remaining lifetime of this mapping is 300 seconds.
<mapping-entry>
<index>15</index>
<type>
dynamic-explicit
</type>
<transport-protocol>
17
</transport-protocol>
<internal-src-address>
192.0.2.1/32
</internal-src-address>
<internal-src-port>
<start-port-number>
1568
</start-port-number>
</internal-src-port>
<external-src-address>
198.51.100.1/32
</external-src-address>
<external-src-port>
<start-port-number>
15000
</start-port-number>
</external-src-port>
<lifetime>
300
</lifetime>
</mapping-entry>
The following XML snippet shows the example of the capabilities supported by a CGN as retrieved using NETCONF.
<capabilities
<nat-flavor>napt44</nat-flavor>
<transport-protocols>
<protocol-id>1</protocol-id>
</transport-protocols>
<transport-protocols>
<protocol-id>6</protocol-id>
</transport-protocols>
<transport-protocols>
<protocol-id>17</protocol-id>
</transport-protocols>
<restricted-port-support>
false
</restricted-port-support>
<static-mapping-support>
true
</static-mapping-support>
<port-randomization-support>
true
</port-randomization-support>
<port-range-allocation-support>
true
</port-range-allocation-support>
<port-preservation-suport>
true
</port-preservation-suport>
<port-parity-preservation-support>
false
</port-parity-preservation-support>
<address-roundrobin-support>
true
</address-roundrobin-support>
<paired-address-pooling-support>
true
</paired-address-pooling-support>
<endpoint-independent-mapping-support>
true
</endpoint-independent-mapping-support>
<address-dependent-mapping-support>
true
</address-dependent-mapping-support>
<address-and-port-dependent-mapping-support>
true
</address-and-port-dependent-mapping-support>
<endpoint-independent-filtering-support>
true
</endpoint-independent-filtering-support>
<address-dependent-filtering>
true
</address-dependent-filtering>
<address-and-port-dependent-filtering>
true
</address-and-port-dependent-filtering>
</capabilities>
The following XML snippet shows the example of a CGN that is provisioned with one contiguous pool of external IPv4 addresses (198.51.100.0/24). Further, the CGN is instructed to limit the number of allocated ports per subscriber to 1024. Ports can be allocated by the CGN by assigning ranges of 256 ports (that is, a subscriber can be allocated up to four port ranges of 256 ports each).
<instances>
<instance>
<id>1</id>
<name>myCGN</name>
....
<external-ip-address-pool>
<pool-id>1</pool-id>
<external-ip-pool>
198.51.100.0/24
</external-ip-pool>
</external-ip-address-pool>
<port-quota>
<port-limit>
1024
</port-limit>
<quota-type >
all
</quota-type >
</port-quota>
<port-allocation-type>
port-range-allocation
</port-allocation-type>
<port-set>
<port-set-size>
256
</port-set-size>
</port-set>
....
</instance>
</instances>
An administrator may decide to allocate one single port range per subscriber (e.g., port range of 1024 ports) as shown below:
<instances>
<instance>
<id>1</id>
<name>myCGN</name>
....
<external-ip-address-pool>
<pool-id>1</pool-id>
<external-ip-pool>
198.51.100.0/24
</external-ip-pool>
</external-ip-address-pool>
<port-quota>
<port-limit>
1024
</port-limit>
<quota-type >
all
</quota-type >
</port-quota>
<port-allocation-type>
port-range-allocation
</port-allocation-type>
<port-set>
<port-set-size>
1024
</port-set-size>
</port-set>
....
</instance>
</instances>
Figure 1 illustrates an example of the CGN pass-through feature.
X1:x1 X1':x1' X2:x2
+---+from X1:x1 +---+from X1:x1 +---+
| C | to X2:x2 | | to X2:x2 | S |
| l |>>>>>>>>>>>>| C |>>>>>>>>>>>>>>| e |
| i | | G | | r |
| e |<<<<<<<<<<<<| N |<<<<<<<<<<<<<<| v |
| n |from X2:x2 | |from X2:x2 | e |
| t | to X1:x1 | | to X1:x1 | r |
+---+ +---+ +---+
Figure 1: CGN Pass-Through
For example, in order to disable NAT for communications issued by the client (192.0.2.1), the following configuration parameter must be set:
<nat-pass-through> ... <prefix>192.0.2.1/32</prefix> ... </nat-pass-through>
Let's consider the example of a NAT64 that should use 2001:db8:122:300::/56 to perform IPv6 address synthesis [RFC6052]. The XML snippet to configure the NAT64 prefix in such case is depicted below:
<nat64-prefixes>
<nat64-prefix>
2001:db8:122:300::/56
</nat64-prefix>
</nat64-prefixes>
Let's now consider the example of a NAT64 that should use 2001:db8:122::/48 to perform IPv6 address synthesis [RFC6052] only if the destination address matches 198.51.100.0/24. The XML snippet to configure the NAT64 prefix in such case is shown below:
<nat64-prefixes>
<nat64-prefix>
2001:db8:122::/48
</nat64-prefix>
<destination-ipv4-prefix>
<ipv4-prefix>
198.51.100.0/24
</ipv4-prefix>
</destination-ipv4-prefix>
</nat64-prefixes>
<nat64-prefixes>
<nat64-prefix>
2001:db8:100::/40
</nat64-prefix>
</nat64-prefixes>
Let's consider the example of a stateless translator that is configured with 2001:db8:100::/40 to perform IPv6 address synthesis [RFC6052]. Similar to the NAT64 case, the XML snippet to configure the NAT64 prefix in such case is depicted below:
When the translator receives an IPv6 packet, for example, with a source address (2001:db8:1c0:2:21::) and destination address (2001:db8:1c6:3364:2::), it extracts embedded IPv4 addresses following RFC6052 rules with 2001:db8:100::/40 as the NSP:
The translator transforms the IPv6 header into an IPv4 header using the IP/ICMP Translation Algorithm [RFC7915]. The IPv4 packets will include 192.0.2.33 as the source address and 198.51.100.2 as the destination address.
Also, a NAT64 can be instructed to behave in the stateless mode by providing the following configuration. The same NAT64 prefix is used for constructing both IPv4-translatable IPv6 addresses and IPv4-converted IPv6 addresses (Section 3.3 of [RFC6052]).
<nat64-prefixes>
<nat64-prefix>
2001:db8:122:300::/56
</nat64-prefix>
<stateless-enable>
true
</stateless-enable>
</nat64-prefixes>
As specified in [RFC7757], an EAM consists of an IPv4 prefix and an IPv6 prefix. Let's consider the set of EAM examples in Table 8.
+----------------+----------------------+
| IPv4 Prefix | IPv6 Prefix |
+----------------+----------------------+
| 192.0.2.1 | 2001:db8:aaaa:: |
| 192.0.2.2/32 | 2001:db8:bbbb::b/128 |
| 192.0.2.16/28 | 2001:db8:cccc::/124 |
| 192.0.2.128/26 | 2001:db8:dddd::/64 |
| 192.0.2.192/29 | 2001:db8:eeee:8::/62 |
| 192.0.2.224/31 | 64:ff9b::/127 |
+----------------+----------------------+
Table 8: EAM Examples (RFC7757)
<eam>
<ipv4-prefix>
192.0.2.1/32
</ipv4-prefix>
<ipv6-prefix>
2001:db8:aaaa::/128
</ipv6-prefix>
</eam>
<eam>
<ipv4-prefix>
192.0.2.2/32
</ipv4-prefix>
<ipv6-prefix>
2001:db8:bbbb::b/128
</ipv6-prefix>
</eam>
<eam>
<ipv4-prefix>
192.0.2.16/28
</ipv4-prefix>
<ipv6-prefix>
2001:db8:cccc::/124
</ipv6-prefix>
</eam>
<eam>
<ipv4-prefix>
192.0.2.128/26
</ipv4-prefix>
<ipv6-prefix>
2001:db8:dddd::/64
</ipv6-prefix>
</eam>
<eam>
<ipv4-prefix>
192.0.2.192/29
</ipv4-prefix>
<ipv6-prefix>
2001:db8:eeee:8::/62
</ipv6-prefix>
</eam>
<eam>
<ipv4-prefix>
192.0.2.224/31
</ipv4-prefix>
<ipv6-prefix>
64:ff9b::/127
</ipv6-prefix>
</eam>
The following XML excerpt illustrates how these EAMs can be configured using the YANG NAT module:
EAMs may be enabled jointly with statefull NAT64. This example shows a NAT64 function that supports static mappings:
<capabilities
<nat-flavor>
nat64
</nat-flavor>
<static-mapping-support>
true
</static-mapping-support>
<port-randomization-support>
true
</port-randomization-support>
<port-range-allocation-support>
true
</port-range-allocation-support>
<port-preservation-suport>
true
</port-preservation-suport>
<address-roundrobin-support>
true
</address-roundrobin-support>
<paired-address-pooling-support>
true
</paired-address-pooling-support>
<endpoint-independent-mapping-support>
true
</endpoint-independent-mapping-support>
<endpoint-independent-filtering-support>
true
</endpoint-independent-filtering-support>
</capabilities>
The following example shows a static mapping that instructs a NAT to translate packets issued from 192.0.2.1 and with source ports in the 100-500 range to 198.51.100.1:1100-1500.
<mapping-entry>
<index>1</index>
<type>
static
</type>
<transport-protocol>
6
</transport-protocol>
<internal-src-address>
192.0.2.1/32
</internal-src-address>
<internal-src-port>
<start-port-number>
100
</start-port-number>
<end-port-number>
500
</end-port-number>
</internal-dst-port>
<external-src-address>
198.51.100.1/32
</external-src-address>
<external-src-port>
<start-port-number>
1100
</start-port-number>
<end-port-number>
1500
</end-port-number>
</external-src-port>
...
</mapping-entry>
The following example shows a static mapping that instructs a NAT to translate TCP packets issued from 192.0.2.0/24 to 198.51.100.0/24.
<mapping-entry>
<index>1</index>
<type>
static
</type>
<transport-protocol>
6
</transport-protocol>
<internal-src-address>
192.0.2.0/24
</internal-src-address>
<external-src-address>
198.51.100.0/24
</external-src-address>
...
</mapping-entry>
The following XML snippet shows an example of a destination NAT that is instructed to translate all packets having 192.0.2.1 as a destination IP address to 198.51.100.1.
<dst-ip-address-pool>
<pool-id>1</pool-id>
<dst-in-ip-pool>
192.0.2.1/32
</dst-in-ip-pool>
<dst-out-ip-pool>
198.51.100.1/32
</dst-out-ip-pool>
</dst-ip-address-pool>
In order to instruct a NAT to translate TCP packets destined to '192.0.2.1:80' to '198.51.100.1:8080', the following XML snippet shows the static mapping configured on the NAT:
<mapping-entry>
<index>1568</index>
<type>
static
</type>
<transport-protocol>
6
</transport-protocol>
<internal-dst-address>
192.0.2.1/32
</internal-dst-address>
<internal-dst-port>
<start-port-number>
80
</start-port-number>
</internal-dst-port>
<external-dst-address>
198.51.100.1/32
</external-dst-address>
<external-dst-port>
<start-port-number>
8080
</start-port-number>
</external-dst-port>
</mapping-entry>
In order to instruct a NAT to translate TCP packets destined to '192.0.2.1:80' (http traffic) to 198.51.100.1 and '192.0.2.1:22' (ssh traffic) to 198.51.100.2, the following XML snippet shows the static mappings configured on the NAT:
<mapping-entry>
<index>123</index>
<type>
static
</type>
<transport-protocol>
6
</transport-protocol>
<internal-dst-address>
192.0.2.1/32
</internal-dst-address>
<internal-dst-port>
<start-port-number>
80
</start-port-number>
</internal-dst-port>
<external-dst-address>
198.51.100.1/32
</external-dst-address>
...
</mapping-entry>
<mapping-entry>
<index>1236</index>
<type>
static
</type>
<transport-protocol>
6
</transport-protocol>
<internal-dst-address>
192.0.2.1/32
</internal-dst-address>
<internal-dst-port>
<start-port-number>
22
</start-port-number>
</internal-dst-port>
<external-dst-address>
198.51.100.2/32
</external-dst-address>
...
</mapping-entry>
The NAT may also be instructed to proceed with both source and destination NAT. To do so, in addition to the above sample to configure destination NAT, the NAT may be provided, for example with a pool of external IP addresses (198.51.100.0/24) to use for source address translation. An example of the corresponding XML snippet is provided hereafter:
<external-ip-address-pool>
<pool-id>1</pool-id>
<external-ip-pool>
198.51.100.0/24
</external-ip-pool>
</external-ip-address-pool>
Instead of providing an external IP address to share, the NAT may be configured with static mapping entries that modify the internal IP address and/or port number.
The following XML snippet shows the example of a CLAT that is configured with 2001:db8:1234::/96 as PLAT-side IPv6 prefix and 2001:db8:aaaa::/96 as CLAT-side IPv6 prefix. The CLAT is also provided with 192.0.0.1/32 (which is selected from the IPv4 service continuity prefix defined in [RFC7335]).
<clat-ipv6-prefixes>
<ipv6-prefix>
2001:db8:aaaa::/96
</ipv6-prefix>
</clat-ipv6-prefixes>
<clat-ipv4-prefixes>
<ipv4-prefix>
192.0.0.1/32
</ipv4-prefix>
</clat-ipv4-prefixes>
<nat64-prefixes>
<nat64-prefix>
2001:db8:1234::/96
</nat64-prefix>
</nat64-prefixes>
Let's consider the example of an NPTv6 translator that should rewrite packets with the source prefix (fd03:c03a:ecab::/48) with the external prefix (2001:db8:1::/48). The internal interface is "eth0" while the external interface is "eth1" (Figure 2).
External Network: Prefix = 2001:db8:1::/48
--------------------------------------
|
|eth1
+-------------+
eth4| NPTv6 |eth2
...-----| |------...
+-------------+
|eth0
|
--------------------------------------
Internal Network: Prefix = fd03:c03a:ecab::/48
Figure 2: Example of NPTv6
The XML snippet to configure NPTv6 prefixes in such case is depicted below:
<nptv6-prefixes>
<internal-ipv6-prefix>
fd03:c03a:ecab::/48
</internal-ipv6-prefix>
<external-ipv6-prefix>
2001:db8:1::/48
</external-ipv6-prefix>
</nptv6-prefixes>
...
<external-realm>
<external-interface>
eth1
</external-interface>
</external-realm>
Figure 3 shows an example of an NPTv6 translator that interconnects two internal networks (fd03:c03a:ecab::/48 and fda8:d5cb:14f3::/48); each is translated using a dedicated prefix (2001:db8:1::/48 and 2001:db8:6666::/48, respectively).
Internal Prefix = fda8:d5cb:14f3::/48
--------------------------------------
V | External Prefix
V |eth1 2001:db8:1::/48
V +---------+ ^
V | NPTv6 | ^
V | | ^
V +---------+ ^
External Prefix |eth0 ^
2001:db8:6666::/48 | ^
--------------------------------------
Internal Prefix = fd03:c03a:ecab::/48
Figure 3: Connecting two Peer Networks
To that aim, the following configuration is provided to the NPTv6 translator:
<policy>
<id>1</id>
<nptv6-prefixes>
<internal-ipv6-prefix>
fd03:c03a:ecab::/48
</internal-ipv6-prefix>
<external-ipv6-prefix>
2001:db8:1::/48
</external-ipv6-prefix>
</nptv6-prefixes>
<external-realm>
<external-interface>
eth1
</external-interface>
</external-realm>
</policy>
<policy>
<id>2</id>
<nptv6-prefixes>
<internal-ipv6-prefix>
fda8:d5cb:14f3::/48
</internal-ipv6-prefix>
<external-ipv6-prefix>
2001:db8:6666::/48
</external-ipv6-prefix>
</nptv6-prefixes>
<external-realm>
<external-interface>
eth0
</external-interface>
</external-realm>
</policy>