Network File System Version 4 C. Lever
Internet-Draft Oracle
Updates: 8166 (if approved) November 15, 2019
Intended status: Standards Track
Expires: May 18, 2020

RDMA Connection Manager Private Data For RPC-Over-RDMA Version 1
draft-ietf-nfsv4-rpcrdma-cm-pvt-data-05

Abstract

This document specifies the format of RDMA-CM Private Data exchanged between RPC-over-RDMA version 1 peers as part of establishing a connection. The addition of the private data payload specified in this document is an optional extension that does not alter the RPC-over-RDMA version 1 protocol. This document updates RFC 8166.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on May 18, 2020.

Copyright Notice

Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

The RPC-over-RDMA version 1 transport protocol [RFC8166] enables payload data transfer using Remote Direct Memory Access (RDMA) for upper-layer protocols based on Remote Procedure Calls (RPC) [RFC5531]. The terms "Remote Direct Memory Access" (RDMA) and "Direct Data Placement" (DDP) are introduced in [RFC5040].

The two most immediate shortcomings of RPC-over-RDMA version 1 are:

RPC-over-RDMA version 1 has no means of extending its XDR definition in such a way that interoperability with existing implementations is preserved. As a result, an out-of-band mechanism is needed to help relieve these constraints for existing RPC-over-RDMA version 1 implementations.

This document specifies a simple, non-XDR-based message format designed to be passed between RPC-over-RDMA version 1 peers at the time each RDMA transport connection is first established. The mechanism assumes that the underlying RDMA transport has a private data field that is passed between peers at connection time, such as is present in the iWARP protocol (described in Section 7.1 of [RFC5044]) or the InfiniBand Connection Manager [IBA].

To enable current RPC-over-RDMA version 1 implementations to interoperate with implementations that support the private message format described in this document, implementation of the private data message is OPTIONAL. When the private data message has been successfully exchanged, peers may choose to perform extended RDMA semantics. However, the private message format does not alter the XDR definition specified in [RFC8166].

The message format is intended to be further extensible within the normal scope of such IETF work (see Section 5 for further details). Section 6 of the current document defines an IANA registry for this purpose. In addition, interoperation between implementations of RPC-over-RDMA version 1 that present this message format to peers and those that do not recognize this message format is guaranteed.

2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. Advertised Transport Properties

3.1. Inline Threshold Size

Section 3.3.2 of [RFC8166] defines the term "inline threshold." An inline threshold is the maximum number of bytes that can be transmitted using one RDMA Send and one RDMA Receive. There are a pair of inline thresholds for a connection: a client-to-server threshold and a server-to-client threshold.

If an incoming message exceeds the size of a receiver's inline threshold, the receive operation fails and the connection is typically terminated. To convey a message larger than a receiver's inline threshold, an NFS client uses explicit RDMA data transfer operations, which are more expensive to use than RDMA Send.

The default value of inline thresholds for RPC-over-RDMA version 1 connections is 1024 bytes (see Section 3.3.3 of [RFC8166]). This value is adequate for nearly all NFS version 3 procedures.

NFS version 4 COMPOUND operations [RFC7530] are larger on average than NFS version 3 procedures [RFC1813], forcing clients to use explicit RDMA operations for frequently-issued requests such as LOOKUP and GETATTR. The use of RPCSEC_GSS security also increases the average size of RPC messages, due to the larger size of RPCSEC_GSS credential material included in RPC headers [RFC7861].

If a sender and receiver could somehow agree on larger inline thresholds, frequently-used RPC transactions avoid the cost of explicit RDMA operations.

3.2. Remote Invalidation

After an RDMA data transfer operation completes, an RDMA consumer can use remote invalidation to request that the remote peer RNIC invalidate an STag associated with the data transfer [RFC5042].

An RDMA consumer requests remote invalidation by posting an RDMA Send With Invalidate Work Request in place of an RDMA Send Work Request. Each RDMA Send With Invalidate carries one STag to invalidate. The receiver of an RDMA Send With Invalidate performs the requested invalidation and then reports that invalidation as part of the completion of a waiting Receive Work Request.

If both peers support remote invalidation, an RPC-over-RDMA responder might use remote invalidation when replying to an RPC request that provided chunks. Because one of the chunks has already been invalidated, finalizing the results of the RPC is made simpler and faster.

However, there are some important caveats which contraindicate the blanket use of remote invalidation:

A responder therefore must not employ remote invalidation unless it is aware of support for it in its own RDMA stack, and on the requester. And, without altering the XDR structure of RPC-over-RDMA version 1 messages, it is not possible to support remote invalidation with requesters that mix STags that may and must not be invalidated remotely in a single RPC or on the same connection.

There are some NFS/RDMA client implementations whose STags are always safe to invalidate remotely. For such clients, indicating to the responder that remote invalidation is always safe can allow such invalidation without the need for additional protocol to be defined.

4. Private Data Message Format

With an InfiniBand lower layer, for example, RDMA connection setup uses a Connection Manager when establishing a Reliable Connection [IBA]. When an RPC-over-RDMA version 1 transport connection is established, the client (which actively establishes connections) and the server (which passively accepts connections) populate the CM Private Data field exchanged as part of CM connection establishment.

The transport properties exchanged via this mechanism are fixed for the life of the connection. Each new connection presents an opportunity for a fresh exchange. An implementation of the extension described in this document MUST be prepared for the settings to change upon a reconnection.

For RPC-over-RDMA version 1, the CM Private Data field is formatted as described in the following subsection. RPC clients and servers use the same format. If the capacity of the Private Data field is too small to contain this message format, the underlying RDMA transport is not managed by a Connection Manager, or the underlying RDMA transport uses Private Data for its own purposes, the CM Private Data field cannot be used on behalf of RPC-over-RDMA version 1.

The first 8 octets of the CM Private Data field is to be formatted as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       Format Identifier                       |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|    Version    |     Flags     |   Send Size   | Receive Size  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Format Identifier:
This field contains a fixed 32-bit value that identifies the content of the Private Data field as an RPC-over-RDMA version 1 CM Private Data message. In RPC-over-RDMA version 1 Private Data, the value of this field is always 0xf6ab0e18, in network byte order. The use of this field is further expanded upon in Section 4.1.
Version:
This 8-bit field contains a message format version number. The value "1" in this field indicates that exactly eight octets are present, that they appear in the order described in this section, and that each has the meaning defined in this section. Further considerations about the use of this field are discussed in Section 5.
Flags:
This 8-bit field contains bit flags that indicate the support status of optional features, such as remote invalidation. The meaning of these flags is defined in Section 5.1.
Send Size:
This 8-bit field contains an encoded value corresponding to the maximum number of bytes this peer is prepared to transmit in a single RDMA Send on this connection. The value is encoded as described in Section 5.2.
Receive Size:
This 8-bit field contains an encoded value corresponding to the maximum number of bytes this peer is prepared to receive with a single RDMA Receive on this connection. The value is encoded as described in Section 5.2.

4.1. Interoperability Considerations

The extension described in this document is designed to allow RPC-over-RDMA version implementations that use CM Private Data to interoperate fully with RPC-over-RDMA version 1 implementations that do not exchange this information. Implementations that use this extension must also interoperate fully with RDMA implementations that use CM Private Data for other purposes. Realizing these goals require that implementations of this extension follow the practices described in the rest of this section.

4.1.1. Amongst RPC-over-RDMA Version 1 Implementations

When a peer does not receive a CM Private Data message which conforms to Section 4, it needs to act as if the remote peer supports only the default RPC-over-RDMA version 1 settings, as defined in [RFC8166]. In other words, the peer MUST behave as if a Private Data message was received in which bit 15 of the Flags field is zero, and both Size fields contain the value zero.

4.1.2. Amongst Implementations of Other Upper-Layer Protocols

The Format Identifier field in the message format defined in this document is provided to enable implementations to distinguish RPC-over-RDMA version 1 Private Data from application-specific private data inserted by applications other than RPC-over RDMA version 1. Examples of other applications that make use of CM Private Data include iWARP, via the MPA enhancement described in [RFC6581], and iSCSI extensions for RDMA (iSER), as defined in [RFC7145].

During connection establishment, an implementation of the extension described in this document checks the Format Identifier field before decoding subsequent fields. If the RPC-over-RDMA version 1 CM Private Data Format Identifier is not present as the first 4 octets, an RPC-over-RDMA version 1 receiver MUST ignore the CM Private Data, behaving as if no RPC-over-RDMA version 1 Private Data has been provided (see above).

5. Updating the Message Format

Although the message format described in this document provides the ability for the client and server to exchange particular information about the local RPC-over-RDMA implementation, it is possible that there will be a future need to exchange additional properties. This would make it necessary to extend or otherwise modify the format described in this document.

Any modification faces the problem of interoperating properly with implementations of RPC-over-RDMA version 1 that are unaware of this existence of the new format. These include implementations that that do not recognize the exchange of CM Private Data as well as those that recognize only the format described in this document.

Given the message format described in this document, these interoperability constraints could be met by the following sorts of new message formats:

Although it is possible to reorganize the last three of the eight bytes in the existing format, extended formats are unlikely to do so. New formats would take the form of extensions of the format described in this document with added fields starting at byte eight of the format and changes to the definition of previously reserved flags.

5.1. Feature Support Flags

The bits in the Flags field are labeled from bit 8 to bit 15, as shown in the diagram above. When the Version field contains the value "1", the bits in the Flags field are to be set as follows:

Bit 15:
When both connection peers have set this flag in their CM Private Data, the responder MAY use RDMA Send With Invalidate when transmitting RPC Replies. Each RDMA Send With Invalidate MUST invalidate an STag associated only with the XID in the rdma_xid field of the RPC-over-RDMA Transport Header it carries.
When either peer on a connection clears this flag, the responder MUST use only RDMA Send when transmitting RPC Replies.
Bits 14 - 8:
These bits are reserved and are always zero when the Version field contains 1.

5.2. Inline Threshold Values

Inline threshold sizes from 1KB to 256KB can be represented in the Send Size and Receive Size fields. A sender computes the encoded value by dividing the actual value by 1024 and subtracting one from the result. A receiver decodes this value by performing a complementary set of operations.

The client uses the smaller of its own send size and the server's reported receive size as the client-to-server inline threshold. The server uses the smaller of its own send size and the clients's reported receive size as the server-to-client inline threshold.

6. IANA Considerations

In accordance with [RFC8126], the author requests that IANA create a new registry in the "Remote Direct Data Placement" Protocol Category Group. The new registry is to be called the "RDMA-CM Private Data Identifier Registry". This is a registry of 32-bit numbers that identify the upper-layer protocol associated with data that appears in the application-specific RDMA-CM Private Data area. The fields in this registry include: Format Identifier, Description, and Reference.

The initial contents of this registry are a single entry:

RDMA-CM Private Data Identifier Registry
Format Identifier Format Description Reference
0xf6ab0e18 RPC-over-RDMA version 1 CM Private Data [RFC-TBD]

IANA is to assign subsequent new entries in this registry using the Expert Review policy as defined in Section 4.5 of [RFC8126].

6.1. Guidance for Designated Experts

The Designated Expert (DE), appointed by the IESG, should ascertain the existence of suitable documentation that defines the semantics and format of the private data, and verify that the document is permanently and publicly available. Documentation produced outside the IETF must not conflict with work that is active or already published within the IETF.

The new Reference field should contain a reference to that documentation. The DE can assign new Format Identifiers at random as long as they do not conflict with existing entries in this registry. The Description field should contain the name of a distinct upper-layer RDMA consumer that will use the private data.

The DE will post the request to the nfsv4 WG mailing list (or a successor to that list, if such a list exists), for comment and review. The DE will approve or deny the request and publish notice of the decision within 30 days.

7. Security Considerations

The Private Data extension specified in this document inherits the security considerations of the protocols it extends, which in this case is defined in [RFC8166].

The integrity of CM Private Data and the authenticity of it's source is ensured by the use of the Reliable connected (RC) Queue Pair (QP) type, required by RPC-over-RDMA version 1. Any attempts to interfere with or hijack an RC connection will result in the connection being immediately terminated. Additional relevant analysis of RDMA security appears in the Security Considerations section of [RFC5042].

Improperly setting one of the fields in the private message payload will result in a greatly increased risk of disconnection (i.e., self-imposed Denial of Service). There is no increased risk of exposing upper-layer data inappropriately.

8. References

8.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997.
[RFC5040] Recio, R., Metzler, B., Culley, P., Hilland, J. and D. Garcia, "A Remote Direct Memory Access Protocol Specification", RFC 5040, DOI 10.17487/RFC5040, October 2007.
[RFC5042] Pinkerton, J. and E. Deleganes, "Direct Data Placement Protocol (DDP) / Remote Direct Memory Access Protocol (RDMAP) Security", RFC 5042, DOI 10.17487/RFC5042, October 2007.
[RFC8126] Cotton, M., Leiba, B. and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017.
[RFC8166] Lever, C., Simpson, W. and T. Talpey, "Remote Direct Memory Access Transport for Remote Procedure Call Version 1", RFC 8166, DOI 10.17487/RFC8166, June 2017.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017.

8.2. Informative References

[IBA] InfiniBand Trade Association, "InfiniBand Architecture Specification Volume 1", Release 1.3, March 2015.

Available from https://www.infinibandta.org/

[RFC1813] Callaghan, B., Pawlowski, B. and P. Staubach, "NFS Version 3 Protocol Specification", RFC 1813, DOI 10.17487/RFC1813, June 1995.
[RFC5044] Culley, P., Elzur, U., Recio, R., Bailey, S. and J. Carrier, "Marker PDU Aligned Framing for TCP Specification", RFC 5044, DOI 10.17487/RFC5044, October 2007.
[RFC5531] Thurlow, R., "RPC: Remote Procedure Call Protocol Specification Version 2", RFC 5531, DOI 10.17487/RFC5531, May 2009.
[RFC5666] Talpey, T. and B. Callaghan, "Remote Direct Memory Access Transport for Remote Procedure Call", RFC 5666, DOI 10.17487/RFC5666, January 2010.
[RFC6581] Kanevsky, A., Bestler, C., Sharp, R. and S. Wise, "Enhanced Remote Direct Memory Access (RDMA) Connection Establishment", RFC 6581, DOI 10.17487/RFC6581, April 2012.
[RFC7145] Ko, M. and A. Nezhinsky, "Internet Small Computer System Interface (iSCSI) Extensions for the Remote Direct Memory Access (RDMA) Specification", RFC 7145, DOI 10.17487/RFC7145, April 2014.
[RFC7530] Haynes, T. and D. Noveck, "Network File System (NFS) Version 4 Protocol", RFC 7530, DOI 10.17487/RFC7530, March 2015.
[RFC7861] Adamson, A. and N. Williams, "Remote Procedure Call (RPC) Security Version 3", RFC 7861, DOI 10.17487/RFC7861, November 2016.

Acknowledgments

Thanks to Christoph Hellwig and Devesh Sharma for suggesting this approach, and to Tom Talpey and Dave Noveck for their expert comments and review. The author also wishes to thank Bill Baker and Greg Marsden for their support of this work.

Special thanks go to Transport Area Director Magnus Westerlund, NFSV4 Working Group Chairs Spencer Shepler and Brian Pawlowski, and NFSV4 Working Group Secretary Thomas Haynes.

Author's Address

Charles Lever Oracle Corporation United States of America EMail: chuck.lever@oracle.com