MARTINI WG A. B. Roach
Internet-Draft Tekelec
Intended status: Standards Track July 6, 2010
Expires: January 7, 2011
Registration for Multiple Phone Numbers in the Session Initiation
Protocol (SIP)
draft-ietf-martini-gin-05
Abstract
This document defines a mechanism by which a SIP server acting as a
traditional Private Branch Exchange (SIP-PBX) can register with a SIP
Service Provider (SSP) to receive phone calls for UAs designated by
phone numbers. In order to function properly, this mechanism relies
on the fact that the phone numbers are fully qualified and globally
unique.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 7, 2011.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
Roach Expires January 7, 2011 [Page 1]
Internet-Draft Globally Identifiable Number Routing July 2010
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Constraints . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Terminology and Conventions . . . . . . . . . . . . . . . . . 4
4. Mechanism Overview . . . . . . . . . . . . . . . . . . . . . . 5
5. Registering for Multiple Phone Numbers . . . . . . . . . . . . 5
5.1. SIP-PBX Behavior . . . . . . . . . . . . . . . . . . . . . 5
5.2. Registrar Behavior . . . . . . . . . . . . . . . . . . . . 6
5.3. SIP URI "user" Parameter Handling . . . . . . . . . . . . 8
6. SSP Processing of Inbound Requests . . . . . . . . . . . . . . 8
7. Interaction with Other Mechanisms . . . . . . . . . . . . . . 9
7.1. Globally Routable User-Agent URIs (GRUU) . . . . . . . . . 9
7.1.1. Public GRUUs . . . . . . . . . . . . . . . . . . . . . 9
7.1.2. Temporary GRUUs . . . . . . . . . . . . . . . . . . . 11
7.2. Registration Event Package . . . . . . . . . . . . . . . . 14
7.2.1. SIP-PBX Aggregate Registration State . . . . . . . . . 15
7.2.2. Individual AOR Registration State . . . . . . . . . . 15
7.3. Client-Initiated (Outbound) Connections . . . . . . . . . 16
7.4. Non-Adjacent Contact Registration (Path) and Service
Route Discovery . . . . . . . . . . . . . . . . . . . . . 16
8. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1. Usage Scenario: Basic Registration . . . . . . . . . . . . 18
8.2. Usage Scenario: Using Path to Control Request URI . . . . 19
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21
9.1. New SIP Option Tag . . . . . . . . . . . . . . . . . . . . 22
9.2. New SIP URI Parameters . . . . . . . . . . . . . . . . . . 22
9.2.1. 'bnc' SIP URI parameter . . . . . . . . . . . . . . . 22
9.2.2. 'sg' SIP URI parameter . . . . . . . . . . . . . . . . 22
9.3. New SIP Header Field Parameter . . . . . . . . . . . . . . 22
10. Security Considerations . . . . . . . . . . . . . . . . . . . 22
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 24
12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 24
12.1. Normative References . . . . . . . . . . . . . . . . . . . 24
12.2. Informative References . . . . . . . . . . . . . . . . . . 25
Appendix A. Requirements Analysis . . . . . . . . . . . . . . . . 26
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 29
Roach Expires January 7, 2011 [Page 2]
Internet-Draft Globally Identifiable Number Routing July 2010
1. Introduction
One of SIP's primary functions is providing rendezvous between users.
By design, this rendezvous has been provided through a combination of
the server look-up procedures defined in RFC 3263 [5], and the
registrar procedures described in RFC 3261 [4].
The intention of the original protocol design was that any user's AOR
would be handled by the authority indicated by the hostport portion
of the AOR. The users registered individual reachability information
with this authority, which would then route incoming requests
accordingly.
In actual deployments, some SIP servers have been deployed in
architectures that, for various reasons, have requirements to provide
dynamic routing information for large blocks of AORs, where all of
the AORs in the block were to be handled by the same server. For
purposes of efficiency, many of these deployments do not wish to
maintain separate registrations for each of the AORs in the block.
This leads to the desire for an alternate mechanism for providing
dynamic routing information for blocks of AORs.
Although the use of REGISTER to update reachability information for
multiple users simultaneously is somewhat beyond the original
semantics defined for REGISTER, this approach has seen significant
deployment in certain environments. In particular, deployments in
which small to medium SIP-PBX servers are addressed using E.164
numbers have used this mechanism to avoid the need to maintain DNS
entries or static IP addresses for the SIP-PBX servers.
In recognition of the momentum that REGISTER-based approaches have
seen in deployments, this document defines a REGISTER-based approach
that is tailored to E.164-addressed UAs in a SIP-PBX environment. It
does not address registration of SIP URIs in which the user portion
is not an E.164 number.
2. Constraints
The following paragraph is perhaps the most important in
understanding the reasons for the design decisions made in this
document.
Within the problem space that has been established for this work,
several constraints shape our solution. These are being defined in
the MARTINI requirements document [8]. In terms of impact to the
solution at hand, the following two constraints have the most
profound effect: (1) The SIP-PBX cannot be assumed to be assigned a
Roach Expires January 7, 2011 [Page 3]
Internet-Draft Globally Identifiable Number Routing July 2010
static IP address; and (2) No DNS entry can be relied upon to
consistently resolve to the IP address of the SIP-PBX.
3. Terminology and Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [3].
Further, the term "SSP" is meant as an acronym for a "SIP Service
Provider," while the term "SIP-PBX" is used to indicate a SIP Private
Branch Exchange.
Indented portions of the document, such as this one, form non-
normative, explanatory sections of the document.
Although SIP is a text-based protocol, some of the examples in this
document cannot be unambiguously rendered without additional markup
due to the constraints placed on the formatting of RFCs. This
document uses the markup convention established in RFC
4475 [14] to avoid ambiguity and meet the RFC layout requirements.
For the sake of completeness, the text defining this markup from
Section 2.1 of RFC 4475 [14] is reproduced in its entirety below:
Several of these examples contain unfolded lines longer than 72
characters. These are captured between tags. The
single unfolded line is reconstructed by directly concatenating
all lines appearing between the tags (discarding any line feeds or
carriage returns). There will be no whitespace at the end of
lines. Any whitespace appearing at a fold-point will appear at
the beginning of a line.
The following represent the same string of bits:
Header-name: first value, reallylongsecondvalue, third value
Header-name: first value,
reallylongsecondvalue
, third value
Header-name: first value,
reallylong
second
value,
Roach Expires January 7, 2011 [Page 4]
Internet-Draft Globally Identifiable Number Routing July 2010
third value
Note that this is NOT SIP header-line folding, where different
strings of bits have equivalent meaning.
4. Mechanism Overview
The overall mechanism is achieved using a REGISTER request with a
specially-formatted Contact URI. This document also defines an
option tag that can be used to ensure a registrar and any
intermediaries understand the mechanism described herein.
The Contact URI itself is tagged with a URI parameter to indicate
that it actually represents a multitude of phone-number-associated
contacts.
We also define some lightweight extensions for Globally Routable UA
URIs (GRUU) to allow the use of public and temporary GRUUs assigned
by the SSP.
Aside from these extensions, the REGISTER message itself is processed
by a registrar in the same way as normal registrations: by updating
its location service with additional AOR-to-Contact bindings.
Note that the list of AORs associated with a SIP-PBX is a matter of
local provisioning at the SSP and at the SIP-PBX. The mechanism
defined in this document does not provide any means to detect or
recover from provisioning mismatches (although the registration event
package can be used as a standardized means for auditing such AORs;
see Section 7.2.1).
5. Registering for Multiple Phone Numbers
5.1. SIP-PBX Behavior
To register for multiple AORs, the SIP-PBX sends a REGISTER message
to the SSP. This REGISTER varies from a typical register in two
important ways. First, it must contain an option tag of "gin" in
both a "Require" header field and a "Proxy-Require" header field.
(The option tag "gin" is an acronym for "generate implicit numbers".)
Second, in at least one "Contact" header field, it must include a
Contact URI that contains the URI parameter "bnc", and no user
portion (hence no "@" symbol). A URI with a "bnc" parameter MUST NOT
contain a user portion. Except for the SIP URI "user" parameter,
this URI MAY contain any other parameters that the SIP-PBX desires.
Roach Expires January 7, 2011 [Page 5]
Internet-Draft Globally Identifiable Number Routing July 2010
These parameters will be echoed back by the SSP in any requests bound
for the SIP-PBX.
Because of the constraints discussed in Section 2, the host portion
of the Contact URI will generally contain an IP address, although
nothing in this mechanism enforces or relies upon that fact. If the
SIP-PBX operator chooses to maintain DNS entries that resolve to the
IP address of his SIP-PBX via RFC 3263 resolution procedures, then
this mechanism works just fine with domain names in the Contact
header field.
The 'bnc' URI parameter indicates that special interpretation of the
Contact URI is necessary: instead of representing a single, concrete
Contact URI to be inserted into the location service, it represents a
multitude of Contact URIs (one for each associated AOR), semantically
resulting in a multitude of AOR-to-Contact rows in the location
service.
Any SIP-PBX implementing the registration mechanism defined in this
document MUST also support the Path mechanism defined by RFC 3327
[9], and MUST include a 'path' option-tag in the Supported header
field of the REGISTER request (which is a stronger requirement than
imposed by the Path mechanism itself). This behavior is necessary
because proxies between the SIP-PBX and the Registrar may need to
insert Path header field values in the REGISTER request for this
document's mechanism to function properly, and per RFC 3327 [9], they
can only do so if the UAC inserted the option-tag in the Supported
header field. In accordance with the procedures defined in RFC 3327
[9], the SIP-PBX is allowed to ignore the Path header fields returned
in the REGISTER response.
5.2. Registrar Behavior
The registrar, upon receipt of a REGISTER message containing at least
one Contact header field with a "bnc" parameter will use the value in
the "To" header field to identify the SIP-PBX for which registration
is being requested. It then authenticates the SIP-PBX (using, e.g.,
SIP Digest authentication, mutual TLS, or some other authentication
mechanism). After the SIP-PBX is authenticated, the registrar
updates its location service with a unique AOR-to-Contact mapping for
each of the AORs associated with the SIP-PBX. Semantically, each of
these mappings will be treated as a unique row in the location
service. The actual implementation may, of course, perform internal
optimizations to reduce the amount of memory used to store such
information.
For each of these unique rows, the AOR will be in the format that the
SSP expects to receive from external parties (e.g.
Roach Expires January 7, 2011 [Page 6]
Internet-Draft Globally Identifiable Number Routing July 2010
"sip:+12145550102@ssp.example.com"), and the corresponding Contact
will be formed by adding to the REGISTER's Contact URI a user portion
containing the fully-qualified, E.164-formatted AOR (including the
preceding "+" symbol) and removing the "bnc" parameter. Aside from
the initial "+" symbol, this E.164-formatted number MUST consist
exclusively of digits from 0 through 9, and explicitly MUST NOT
contain any visual separator symbols (e.g., "-", ".", "(", or ")").
For example, if the "Contact" header field contains the URI , then the Contact value associated with the
aforementioned AOR will be .
Although the SSP treats this registration as a number of discrete
rows for the purpose of re-targeting incoming requests, the renewal,
expiration, and removal of these rows is bound to the registered
"bnc" contact. In particular, this means that REGISTER requests that
attempt to de-register a single AOR that has been implicitly
registered MUST NOT remove that AOR from the bulk registration. A
further implication of this property is that an individual extension
that is implicitly registered may also be explicitly registered using
a normal, non-bulk registration (subject to SSP policy). If such a
registration exists, it is refreshed independently of the bulk
registration, and is not removed when the bulk registration is
removed.
A registrar that receives a Contact URI with both a "bnc" parameter
and a user portion MUST either discard the user portion and process
the request as if the parameter were not present or return a 400 (Bad
Request) error in response (unless some other error code is more
appropriate).
Note that the preceding paragraph is talking about the user
portion of a URI:
sip:+12145550100@example.com
^^^^^^^^^^^^
A Registrar compliant with this document MUST support the Path
mechanism defined in RFC 3327 [9].
Aside from the "bnc" and "user" parameters, all URI parameters
present on the "Contact" URI in the REGISTER message MUST be copied
to the Contact value stored in the location service.
If the SSP servers perform processing based on User Agent
Capabilities (as defined in RFC 3840 [12]), they will treat any
feature tags present on a "bnc" Contact header field as applicable to
all of the resulting AOR-to-Contact mappings. Similarly, any option
tags present on the REGISTER request that indicate special handling
Roach Expires January 7, 2011 [Page 7]
Internet-Draft Globally Identifiable Number Routing July 2010
for any subsequent requests are also applicable to all of the AOR-to-
Contact mappings.
5.3. SIP URI "user" Parameter Handling
This document does not modify the behavior specified in RFC 3261 [4]
for inclusion of the "user" parameter on request URIs. However, to
avoid any ambiguity in handling at the SIP-PBX, the following
normative behavior is imposed on its interactions with the SSP.
When a SIP-PBX registers with an SSP using a "bnc" contact, that
contact MUST NOT include a "user" parameter. An SSP registrar that
receives a Contact URI with both a "bnc" parameter and a "user"
parameter MUST either discard the "user" parameter and process the
request as if the parameter were not present or return a 400 (Bad
Request) error in response (unless some other error code is more
appropriate).
Note that the preceding paragraph is talking about the "user"
parameter of a URI:
sip:+12145550100@example.com;user=phone
^^^^^^^^^^
When a SIP-PBX receives a request from an SSP, and the Request-URI
contains a user portion corresponding to an AOR registered using
'bnc' procedures, then the SIP-PBX MUST NOT reject the request (or
otherwise cause the request to fail) due to the absence, presence, or
value of a "user" parameter on the Request-URI.
6. SSP Processing of Inbound Requests
In general, after processing the AOR-to-Contact mapping described in
the preceding section, the SSP Proxy/Registrar (or equivalent entity)
performs traditional Proxy/Registrar behavior, based on the mapping.
For any inbound SIP requests whose AOR indicates an E.164 number
assigned to one of the SSP's customers, this will generally involve
setting the target set to the registered contacts associated with
that AOR, and performing request forwarding as described in section
16.6 of RFC 3261 [4]. An SSP using the mechanism defined in this
document MUST perform such processing for inbound INVITE requests and
SUBSCRIBE requests to the "reg" event package (see Section 7.2.2),
and SHOULD perform such processing for all other method types,
including unrecognized SIP methods.
Roach Expires January 7, 2011 [Page 8]
Internet-Draft Globally Identifiable Number Routing July 2010
7. Interaction with Other Mechanisms
The following sections describe the means by which this mechanism
interacts with relevant REGISTER-related extensions currently defined
by the IETF.
Currently, the descriptions are somewhat informal, and omit some
details for the sake of brevity. If the MARTINI working group
expresses interest in furthering the mechanism described by this
document, they will be fleshed out with more detail and formality.
7.1. Globally Routable User-Agent URIs (GRUU)
To enable advanced services to work with UAs behind a SIP-PBX, it is
important that the GRUU mechanism defined by RFC 5627 [16] work
correctly with the mechanism defined by this document -- that is,
that User Agents services by the SIP-PBX can acquire and use GRUUs
for their own use.
7.1.1. Public GRUUs
When a SIP-PBX registers a Bulk Number Contact (a Contact with a
"bnc" parameter), and also invokes GRUU procedures for that Contact
during registration, then the SSP will assign a public GRUU to the
SIP-PBX in the normal fashion. Because the URI being registered
contains a "bnc" parameter, the GRUU will also contain a "bnc"
parameter. In particular, this means that the GRUU will not contain
a user portion.
When a UA registers with the SIP-PBX using GRUU procedures for a
Contact, the SIP-PBX adds an "sg" parameter to the GRUU parameter it
received from the SSP. This "sg" parameter contains a disambiguation
token that the SIP-PBX can use to route the request to the proper
user agent.
So, for example, when the SIP-PBX registers with the following
contact header field:
Contact: ;
+sip.instance=""
Then the SSP may choose to respond with a Contact header field that
looks like this:
Roach Expires January 7, 2011 [Page 9]
Internet-Draft Globally Identifiable Number Routing July 2010
Contact: ;
pub-gruu="sip:ssp.example.com;bnc;gr=urn:
uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6";
+sip.instance=""
;expires=7200
When its own UAs register, the SIP-PBX can then add whatever device
identifier it feels appropriate in an "sg" parameter, and present
this value to its own UAs. For example, assume the UA associated
with the AOR "+12145550102" sent the following Contact header field
in its register:
Contact: ;
+sip.instance=""
The SIP-PBX will add an "sg" parameter to the pub-gruu it received
from the SSP with a token that uniquely identifies the device
(possibly the URN itself; possibly some other identifier); insert a
user portion containing the fully-qualified E.164 number associated
with the UA; and return the result to the UA as its public GRUU. The
resulting Contact header field sent from the SIP-PBX to the
registering UA would look something like this:
Contact: ;
pub-gruu="sip:+12145550102@ssp.example.com;bnc;gr=urn:
uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6;sg=00:05:03:5e:70:a6";
+sip.instance=""
;expires=3600
When an incoming request arrives at the SSP for a GRUU corresponding
to a bulk number contact ("bnc"), the SSP performs slightly different
processing for the GRUU than a Proxy/Registrar would. When the GRUU
is re-targeted to the registered bulk number contact, the SSP MUST
copy the "sg" parameter from the GRUU to the new target. The SIP-PBX
can then use this "sg" parameter to determine which user agent the
request should be routed to. For example, the first line of an
INVITE request that has been re-targeted to the SIP-PBX for the UA
shown above would look like this:
INVITE sip:+12145550102@198.51.100.3;sg=00:05:03:5e:70:a6 SIP/2.0
Roach Expires January 7, 2011 [Page 10]
Internet-Draft Globally Identifiable Number Routing July 2010
7.1.2. Temporary GRUUs
Temporary GRUUs are used to provide anonymity for the party creating
and sharing the GRUU. Being able to correlate two temporary GRUUs as
having originated from behind the same SIP-PBX violates this
principle of anonymity. Consequently, rather than relying upon a
single, invariant identifier for the SIP-PBX in its UA's temporary
GRUUs, we define a mechanism whereby the SSP provides the SIP-PBX
with sufficient information for the SIP-PBX to mint unique temporary
GRUUs. These GRUUs have the property that the SSP can correlate them
to the proper SIP-PBX, but no other party can do so. To achieve this
goal, we use a slight modification of the procedure described in
appendix A.2 of RFC 5627 [16].
The SIP-PBX must be able to construct a temp-gruu in a way that the
SSP can decode. In order to ensure that the SSP can decode GRUUs, we
need to standardize the algorithm for creation of temp-gruus at the
SIP-PBX. This allows the SSP to reverse the algorithm to identify
the registration entry that corresponds to the GRUU.
It is equally important that no party other than the SSP is capable
of decoding a temporary GRUU, including other SIP-PBXes serviced by
the SSP. To achieve this property, an SSP that supports temporary
GRUUs MUST create and store an asymmetric key pair, {K_e1,K_e2}.
K_e1 is kept secret by the SSP, while K_e2 is shared with the SIP-
PBXes via provisioning.
All base64 encoding discussed in the following sections MUST use the
character set and encoding defined in RFC 2045 [1], except that any
trailing "=" characters are discarded on encoding, and added as
necessary to decode.
7.1.2.1. Generation of temp-gruu-cookie by the SSP
An SSP that supports temporary GRUUs MUST include a "temp-gruu-
cookie" parameter on all "bnc" Contact header fields in a 200-class
REGISTER response. This "temp-gruu-cookie" MUST have the following
properties:
1. It can be used by the SSP to uniquely identify the registration
to which it corresponds.
2. It cannot be modified by the recipient to hijack calls intended
for another SIP-PBX.
3. It cannot be replayed at a later date to hijack calls intended
for another SIP-PBX.
4. It is encoded using base64. This allows the SIP-PBX to decode it
into as compact a form as possible for use in its calculations.
Roach Expires January 7, 2011 [Page 11]
Internet-Draft Globally Identifiable Number Routing July 2010
5. It is of a fixed length. This allows for extraction of it once
the SIP-PBX has concatenated a distinguisher onto it.
The above properties can be met using the following algorithm, which
is non-normative. Implementors may chose to implement any algorithm
of their choosing for generation of the temp-gruu-cookie, as long as
it fulfills the five properties listed above.
The SSP registrar maintains a counter, I. this counter is 48 bits
long, and initialized to zero. This counter is persistently
stored, using a back-end database or similar technique. When the
SSP registrar creates the first temporary GRUU for a particular
SIP-PBX and instance ID, the SSP registrar notes the current value
of the counter, I_i, and increments the counter in the database.
The SSP registrar then maps I_i to the "bnc" AOR template and
instance ID using the database, a persistent hash-map or similar
technology. If the registration expires such that there are no
longer any contacts with that particular instance ID bound to the
GRUU, the SSP registrar removes the mapping. Similarly, if the
temporary GRUUs are invalidated due to a change in Call-ID, the
SSP registrar removes the current mapping from I_i to the AOR and
instance ID, notes the current value of the counter I_j, and
stores a mapping from I_j to the "bnc" AOR template and instance
ID. Based on these rules, the hash-map will contain a single
mapping for each "bnc" AOR template and instance ID for which
there is a currently valid registration.
The SSP registrar maintains a symmetric key SK_a, which is
regenerated every time the counter rolls over or is is reset.
When the counter rolls over or is reset, the SSP registrar
remembers the old value of SK_a for a while. To generate a temp-
gruu-cookie, the SSP registrar computes:
SA = HMAC-SHA256-80(SK_a, I_i)
temp-gruu-cookie = base64enc(I_i || SA)
7.1.2.2. Generation of temp-gruu by the SIP-PBX
A SIP-PBX that issues temporary GRUUs to its UAs MUST maintain an
HMAC key, PK_a. This value is used to validate that incoming GRUUs
were generated by the SIP-PBX.
To generate a new temporary GRUU for use by its own UAs, the SIP-PBX
MUST generate a random distinguisher value D. The length of this
value is up to implementors, but MUST be long enough to prevent
collisions among all the temporary GRUUs issued by the SIP-PBX. A
Roach Expires January 7, 2011 [Page 12]
Internet-Draft Globally Identifiable Number Routing July 2010
size of 80 bits or longer is RECOMMENDED. The SIP-PBX then MUST
calculate:
M = base64dec(SSP-cookie) || D
E = RSA-Encrypt(K_e2, M)
PA = HMAC(PK_a, E)
Temp-Gruu-userpart = "tgruu." || base64(E) || "." || base64(PA)
where || denotes concatenation. "HMAC" represents any suitably
strong HMAC algorithm; see RFC 2104 [2] for a discussion of HMAC
algorithms. One suitable HMAC algorithm for this purpose is HMAC-
SHA256-80.
Finally, the SIP-PBX adds a "gr" parameter to the temporary GRUU that
can be used to uniquely identify the UA registration record to which
the GRUU corresponds. The means of generation of the "gr" parameter
are left to the implementor, as long as they satisfy the properties
of a GRUU as described in RFC 5627 [16].
One valid approach for generation of the "gr" parameter is
calculation of "E" and "A" as described in Appendix A.2 of RFC
5627 [16], and forming the "gr" parameter as:
gr = base64enc(E) || base64enc(A)
Using this procedure may result in a temporary GRUU returned to the
registering UA by the SIP-PBX that looks similar to this:
Contact:
;temp-gruu="sip:tgruu.MQyaRiLEd78RtaWkcP7N8Q.5qVbsasdo2pkKw@
ssp.example.com;gr=YZGSCjKD42ccxO08pA7HwAM4XNDIlMSL0HlA"
;+sip.instance=""
;expires=3600
7.1.2.3. Decoding of temp-gruu by the SSP
When the SSP proxy receives a request in which the user part begins
with "tgruu.", it extracts the remaining portion, and splits it at
the "." character into E' and PA'. It discards PA'. It then
computes E by performing a base64 decode of E'. Next, it computes:
Roach Expires January 7, 2011 [Page 13]
Internet-Draft Globally Identifiable Number Routing July 2010
M = RSA-Decrypt(K_e1, E)
The SSP proxy extracts the fixed-length temp-gruu-cookie information
from the beginning of this M, and discards the remainder (which will
be the distinguisher added by the SIP-PBX). It then validates this
temp-gruu-cookie. If valid, it uses it to locate the corresponding
SIP-PBX registration record, and routes the message appropriately.
If the non-normative, exemplary algorithm described in
Section 7.1.2.1 is used to generate the temp-gruu-cookie, then
this identification is performed by splitting the temp-gruu-cookie
information into its 48-bit counter I and 80-bit HMAC. It
validates that the HMAC matches the counter I, and then uses
counter I to locate the SIP-PBX registration record in its map.
If the counter has rolled over or reset, this computation is
performed with the current and previous SK_a.
7.1.2.4. Decoding of temp-gruu by the SIP-PBX
When the SIP-PBX receives a request in which the user part begins
with "tgruu.", it extracts the remaining portion, and splits it at
the "." character into E' and PA'. It then computes E and PA by
performing a base64 decode of E' and PA' respectively. Next, it
computes:
PAc = HMAC(PK_a, E)
where HMAC is the HMAC algorithm used for the steps in
Section 7.1.2.2. If this computed value for PAc does not match the
value of PA extracted from the GRUU, then the GRUU is rejected as
invalid.
The SIP-PBX then uses the value of the "gr" parameter to locate the
UA registration to which the GRUU corresponds, and routes the message
accordingly.
7.2. Registration Event Package
As this mechanism inherently deals with REGISTER behavior, it is
imperative to consider its impact on the Registration Event Package
defined by RFC 3680 [11]. In practice, there will be two main use
cases for subscribing to registration data: learning about the
overall registration state for the SIP-PBX, and learning about the
registration state for a single SIP-PBX AOR.
Roach Expires January 7, 2011 [Page 14]
Internet-Draft Globally Identifiable Number Routing July 2010
7.2.1. SIP-PBX Aggregate Registration State
If the SIP-PBX (or another interested and authorized party) wishes to
monitor or audit the registration state for all of the AORs currently
registered to that SIP-PBX, it can subscribe to the SIP registration
event package at the SIP-PBX's main URI -- that is, the URI used in
the "To" header field of the REGISTER message.
The NOTIFY messages for such a subscription will contain a body that
contains one record for each AOR associated with the SIP-PBX. The
AORs will be in the format expected to be received by the SSP (e.g.,
"sip:+12145550105@ssp.example.com"), and the Contacts will correspond
to the mapped Contact created by the registration (e.g.,
"sip:+12145550105@98.51.100.3").
In particular, the "bnc" parameter is forbidden from appearing in the
body of a reg-event notify.
7.2.2. Individual AOR Registration State
As described in Section 6, the SSP will generally retarget all
requests addressed to an AOR owned by a SIP-PBX to that SIP-PBX
according to the mapping established at registration time. Although
policy at the SSP may override this generally expected behavior,
proper behavior of the registration event package requires that all
"reg" event SUBSCRIBE requests are processed by the SIP-PBX. As a
consequence, the requirements on an SSP for processing registration
event package SUBSCRIBE requests are not left to policy.
If the SSP receives a SUBSCRIBE request for the registration event
package with a Request-URI that indicates a contact registered via
the "Bulk Number Contact" mechanism defined in this document, then
the SSP MUST proxy that SUBSCRIBE to the SIP-PBX in the same way that
is would proxy an INVITE bound for that AOR, unless the SSP has and
can maintain a copy of complete, accurate, and up-to-date information
from the SIP-PBX (e.g., through an active back-end subscription).
Defining the behavior in this way is important, since the reg-event
subscriber is interested in finding out about the comprehensive list
of devices associated with the AOR. Only the SIP-PBX will have
authoritative access to this information. For example, if the user
has registered multiple UAs with differing capabilities, the SSP will
not know about the devices or their capabilities. By contrast, the
SIP-PBX will.
When a SIP-PBX receives a registration event subscription addressed
to an AOR that has been registered using the bulk registration
mechanism described in this document, then the resulting registration
Roach Expires January 7, 2011 [Page 15]
Internet-Draft Globally Identifiable Number Routing July 2010
information documents SHOULD contain an 'aor' attribute in its
element that corresponds to the AOR at the SSP.
For example, consider a SIP-PBX that has registered with an SSP
that has a domain of "ssp.example.com" The SIP-PBX used a contact
of "sip:198.51.100.3:5060;bnc". After such registration is
complete, a registration event subscription arriving at the SSP
with a Request-URI of "sip:+12145550102@ssp.example.com" will be
re-targeted to the SIP-PBX, with a Request-URI of
"sip:+12145550102@198.51.100.3:5060". The resulting registration
document created by the SIP-PBX would contain a
element with an "aor" attribute of
"sip:+12145550102@ssp.example.com".
This behavior ensures that subscribers external to the system (and
unaware of GIN procedures) will be able to find the relevant
information in the registration document (since they will be
looking for the publicly-visible AOR, not the address used for
sending information from the SSP to the SIP-PBX).
7.3. Client-Initiated (Outbound) Connections
RFC 5626 [15] defines a mechanism that allows UAs to establish long-
lived TCP connections or UDP associations with a proxy in a way that
allows bidirectional traffic between the proxy and the UA. This
behavior is particularly important in the presence of NATs, and
whenever TLS security is required.
The outbound mechanism generally works with the solution defined in
this document without any modifications. Implementors should note
that the instance ID used between the SIP-PBX and the SSP's registrar
identifies the SIP-PBX itself, and not any of the UAs registered with
the SIP-PBX. As a consequence, any attempts to use caller
preferences (defined in RFC 3841[13]) to target a specific instance
are likely to fail. This shouldn't be an issue, as the preferred
mechanism for targeting specific instances of a user agent is GRUU
(see Section 7.1).
7.4. Non-Adjacent Contact Registration (Path) and Service Route
Discovery
RFC 3327 [9] defines a means by which a registrar and its associated
proxy can be informed of a route that is to be used between the proxy
and the registered user agent. The scope of the route created by a
"Path" header field is contact-specific; if an AOR has multiple
contacts associated with it, the routes associated with each contact
may be different from each other.
Roach Expires January 7, 2011 [Page 16]
Internet-Draft Globally Identifiable Number Routing July 2010
At registration time, any proxies between the user agent and the
registrar may add themselves to the Path. By doing so, they request
that any requests destined to the user agent as a result of the
associated registration include them as part of the Route towards the
User Agent. Although the Path mechanism does deliver the final Path
value to the registering UA, UAs typically ignore the value of the
Path.
To provide similar functionality in the opposite direction -- that
is, to establish a route for requests sent by a registering UA -- RFC
3608 [10] defines a means by which a UA can be informed of a route
that is to be used by the UA to route all outbound requests
associated with the AOR used in the registration. This information
is scoped to the AOR within the UA, and is not specific to the
Contact (or Contacts) in the REGISTER request.
The registrar unilaterally generates the values of the service route
using whatever local policy it wishes to apply. Although it is
common to use the Path and/or Route information in the request in
composing the Service-Route, registrar behavior is not constrained in
any way that requires it to do so.
In considering the interaction between these mechanisms and the
registration of multiple AORs in a single request, implementors of
proxies, registrars, and intermediaries must keep in mind the
following issues, which stem from the fact that GIN effectively
registers multiple AORs and multiple Contacts.
First, all location service records that result from expanding a
single "bnc" Contact will necessarily share a single path. Proxies
will be unable to make policy decisions on a contact-by-contact basis
regarding whether to include themselves in the path. Second, and
similarly, all AORs on the SIP-PBX that are registered with a common
REGISTER message will be forced to share a common Service-Route.
One interesting technique that Path and Service-Route enable is the
inclusion of a token or cookie in the user portion of the Service-
Route or Path entries. This token or cookie may convey information
to proxies about the identity, capabilities, and/or policies
associated with the user. Since this information will be shared
among several AORs and several Contacts when multiple AOR
registration is employed, care should be taken to ensure that doing
so is acceptable for all AORs and all Contacts registered in a single
REGISTER message.
Roach Expires January 7, 2011 [Page 17]
Internet-Draft Globally Identifiable Number Routing July 2010
8. Examples
8.1. Usage Scenario: Basic Registration
This example shows the message flows for a basic bulk REGISTER
transaction, followed by an INVITE addressed to one of the registered
UAs. Example messages are shown after the sequence diagram.
Internet SSP SIP-PBX
| | |
| |(1) REGISTER |
| |Contact: |
| |<--------------------------------|
| | |
| |(2) 200 OK |
| |-------------------------------->|
| | |
|(3) INVITE | |
|sip:+12145550105@ssp.example.com| |
|------------------------------->| |
| | |
| |(4) INVITE |
| |sip:+12145550105@198.51.100.3 |
| |-------------------------------->|
(1) The SIP-PBX registers with the SSP for a range of AORs.
REGISTER sip:ssp.example.com SIP/2.0
Via: SIP/2.0/UDP 198.51.100.3:5060;branch=z9hG4bKnashds7
Max-Forwards: 70
To:
From: ;tag=a23589
Call-ID: 843817637684230@998sdasdh09
CSeq: 1826 REGISTER
Proxy-Require: gin
Require: gin
Supported: path
Contact:
Expires: 7200
Content-Length: 0
Roach Expires January 7, 2011 [Page 18]
Internet-Draft Globally Identifiable Number Routing July 2010
(3) The SSP receives a request for an AOR assigned
to the SIP-PBX.
INVITE sip:+12145550105@ssp.example.com SIP/2.0
Via: SIP/2.0/UDP foo.example;branch=z9hG4bKa0bc7a0131f0ad
Max-Forwards: 69
To:
From: ;tag=456248
Call-ID: f7aecbfc374d557baf72d6352e1fbcd4
CSeq: 24762 INVITE
Contact:
Content-Type: application/sdp
Content-Length: ...
(4) The SSP retargets the incoming request according to the
information received from the SIP-PBX at registration time.
INVITE sip:+12145550105@198.51.100.3 SIP/2.0
Via: SIP/2.0/UDP foo.example;branch=z9hG4bKa0bc7a0131f0ad
Via: SIP/2.0/UDP ssp.example.com;branch=z9hG4bKa45cd5c52a6dd50
Max-Forwards: 68
To:
From: ;tag=456248
Call-ID: 7ca24b9679ffe9aff87036a105e30d9b
CSeq: 24762 INVITE
Contact:
Content-Type: application/sdp
Content-Length: ...
8.2. Usage Scenario: Using Path to Control Request URI
This example shows a bulk REGISTER transaction with the SSP making
use of the "Path" header field extension [9]. This allows the SSP to
designate a domain on the incoming Request URI that does not
necessarily resolve to the SIP-PBX from when the SSP applies RFC 3263
procedures to it.
Roach Expires January 7, 2011 [Page 19]
Internet-Draft Globally Identifiable Number Routing July 2010
Internet SSP SIP-PBX
| | |
| |(1) REGISTER |
| |Path: |
| |Contact: |
| |<--------------------------------|
| | |
| |(2) 200 OK |
| |-------------------------------->|
| | |
|(3) INVITE | |
|sip:+12145550105@ssp.example.com| |
|------------------------------->| |
| | |
| |(4) INVITE |
| |sip:+12145550105@pbx.example |
| |Route: |
| |-------------------------------->|
(1) The SIP-PBX registers with the SSP for a range of AORs.
It includes the URI it expects to receive in the Request-URI
in its "Contact" header field, and includes information that
routes to the SIP-PBX in the "Path" header field.
REGISTER sip:ssp.example.com SIP/2.0
Via: SIP/2.0/UDP 198.51.100.3:5060;branch=z9hG4bKnashds7
Max-Forwards: 70
To:
From: ;tag=a23589
Call-ID: 843817637684230@998sdasdh09
CSeq: 1826 REGISTER
Proxy-Require: gin
Require: gin
Supported: path
Path:
Contact:
Expires: 7200
Content-Length: 0
Roach Expires January 7, 2011 [Page 20]
Internet-Draft Globally Identifiable Number Routing July 2010
(3) The SSP receives a request for an AOR assigned
to the SIP-PBX.
INVITE sip:+12145550105@ssp.example.com SIP/2.0
Via: SIP/2.0/UDP foo.example;branch=z9hG4bKa0bc7a0131f0ad
Max-Forwards: 69
To:
From: ;tag=456248
Call-ID: f7aecbfc374d557baf72d6352e1fbcd4
CSeq: 24762 INVITE
Contact:
Content-Type: application/sdp
Content-Length: ...
(4) The SSP retargets the incoming request according to the
information received from the SIP-PBX at registration time.
Per the normal processing associated with "Path," it
will insert the "Path" value indicated by the SIP-PBX at
registration time in a "Route" header field, and
set the request URI to the registered Contact.
INVITE sip:+12145550105@pbx.example SIP/2.0
Via: SIP/2.0/UDP foo.example;branch=z9hG4bKa0bc7a0131f0ad
Via: SIP/2.0/UDP ssp.example.com;branch=z9hG4bKa45cd5c52a6dd50
Route:
Max-Forwards: 68
To:
From: ;tag=456248
Call-ID: 7ca24b9679ffe9aff87036a105e30d9b
CSeq: 24762 INVITE
Contact:
Content-Type: application/sdp
Content-Length: ...
9. IANA Considerations
This document registers a new SIP option tag to indicate support for
the mechanism it defines, plus two new SIP URI parameters.
Roach Expires January 7, 2011 [Page 21]
Internet-Draft Globally Identifiable Number Routing July 2010
9.1. New SIP Option Tag
This section defines a new SIP option tag per the guidelines in
Section 27.1 of RFC 3261[4].
Name: gin
Description: This option tag is used to identify the extension that
provides Registration for Multiple Phone Numbers in SIP. When
present in a Require or Proxy-Require header field of a REGISTER
request, it indicates that support for this extension is required
of registrars and proxies, respectively, that are a party to the
registration transaction.
Reference: RFCXXXX (this document)
9.2. New SIP URI Parameters
This specification defines two new SIP URI parameters, as per the
registry created by RFC 3969 [7].
9.2.1. 'bnc' SIP URI parameter
Parameter Name: bnc
Predefined Values: No (no values are allowed)
Reference: RFCXXXX (this document)
9.2.2. 'sg' SIP URI parameter
Parameter Name: sg
Predefined Values: No
Reference: RFCXXXX (this document)
9.3. New SIP Header Field Parameter
This section defines a new SIP header field parameter per the
registry created by RFC3968 [6].
Header field: Contact
Parameter name: temp-gruu-cookie
Predefined values: none
Reference: RFCXXXX (this document)
10. Security Considerations
The change proposed for the mechanism described in this document
takes the unprecedented step of extending the previously-defined
REGISTER method to apply to more than on AOR. In general, this kind
of change has the potential to cause problems at intermediaries --
such as proxies -- that are party to the REGISTER transaction. In
Roach Expires January 7, 2011 [Page 22]
Internet-Draft Globally Identifiable Number Routing July 2010
particular, such intermediaries may attempt to apply policy to the
user indicated in the "To" header field (i.e. the SIP-PBX's
identity), without any knowledge of the multiple AORs that are being
implicitly registered.
The mechanism defined by this document solves this issue by adding an
option tag to a "Proxy-Require" header in such REGISTER requests.
Proxies that are unaware of this mechanism will not process the
requests, preventing them from mis-applying policy. Proxies that
process requests with this option tag are clearly aware of the nature
of the REGISTER request, and can make reasonable policy decisions.
As noted in Section 7.4, intermediaries need to take care if they use
a policy token in the Path and Service-Route mechanisms, as doing so
will cause them to apply the same policy to all users serviced by the
same SIP-PBX. This may frequently be the correct behavior, but
circumstances can arise in which differentiation of user policy is
required.
One of the key properties of the outbound client connection mechanism
discussed in Section 7.3 is assurances that a single connection is
associated with a single user, and cannot be hijacked by other users.
With the mechanism defined in this document, such connections
necessarily become shared between users. However, the only entity in
a position to hijack calls as a consequence is the SIP-PBX itself.
Because the SIP-PBX acts as a registrar for all the potentially
effected users, it already has the ability to redirect any such
communications as it sees fit. In other words, the SIP-PBX must be
trusted to handle calls in an appropriate fashion, and the use of the
outbound connection mechanism introduces no additional
vulnerabilities.
The ability to learn the identity and registration state of every use
on the PBX (as described in Section 7.2.1) is invaluable for
diagnostic and administrative purposes. For example, this allows the
SIP-PBX to determine whether all the its extensions are properly
registered with the SSP. However, this information can also be
highly sensitive, as many organizations may not wish to make their
entire list of phone numbers available to external entities.
Consequently, SSP servers are advised to use explicit (i.e. white-
list) and configurable policies regarding who can access this
information, with very conservative defaults (e.g., an empty access
list or an access list consisting only of the PBX itself).
The procedure for generation of temporary GRUUs requires the use of
RSA keys. The selection of the proper key length for such keys
requires careful analysis, taking into consideration the current and
foreseeable speed of processing for the period of time during which
Roach Expires January 7, 2011 [Page 23]
Internet-Draft Globally Identifiable Number Routing July 2010
GRUUs must remain anonymous, as well as emerging cryptographic
analysis methods. The most recent guidance from RSA Laboratories
[17] suggests a key length of 2048 bits for data that needs
protection through the year 2030, and a length of 3072 bits
thereafter.
Similarly, implementors are warned to take precautionary measures to
prevent unauthorized disclosure of the private key used in GRUU
generation. Any such disclosure would result in the ability to
correlate temporary GRUUs to each other, and potentially to their
associated PBXes.
Finally, good security practices should be followed regarding the
duration an RSA key is used. For implementors, this means that
systems MUST include an easy way to update the public key provided to
the SIP-PBX. To avoid immediately invalidating all currently issued
temporary GRUUs, the SSP servers SHOULD keep the retired RSA key
around for a grace period before discarding it. If decryption fails
based on the new RSA key, then the SSP server can attempt to use the
retired key instead. By contrast, the SIP-PBXes MUST discard the
retired public key immediately, and exclusively use the new public
key.
11. Acknowledgements
Thanks to John Elwell for his requirements analysis of the mechanism
described in this document, and to Dean Willis for his analysis of
the interaction between this mechanism and the Path and Service-Route
extensions. Thanks to Eric Rescorla, whose text in the appendix of
RFC5627 was lifted directly to provide substantial portions of
Section 7.1.2.
12. References
12.1. Normative References
[1] Freed, N. and N. Borenstein, "Multipurpose Internet Mail
Extensions (MIME) Part One: Format of Internet Message Bodies",
RFC 2045, November 1996.
[2] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-Hashing
for Message Authentication", RFC 2104, February 1997.
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
Roach Expires January 7, 2011 [Page 24]
Internet-Draft Globally Identifiable Number Routing July 2010
[4] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP:
Session Initiation Protocol", RFC 3261, June 2002.
[5] Rosenberg, J. and H. Schulzrinne, "Session Initiation Protocol
(SIP): Locating SIP Servers", RFC 3263, June 2002.
[6] Camarillo, G., "The Internet Assigned Number Authority (IANA)
Header Field Parameter Registry for the Session Initiation
Protocol (SIP)", BCP 98, RFC 3968, December 2004.
[7] Camarillo, G., "The Internet Assigned Number Authority (IANA)
Uniform Resource Identifier (URI) Parameter Registry for the
Session Initiation Protocol (SIP)", BCP 99, RFC 3969,
December 2004.
12.2. Informative References
[8] Elwell, J. and H. Kaplan, "Requirements for multiple address of
record (AOR) reachability information in the Session Initiation
Protocol (SIP)", draft-ietf-martini-reqs-08 (work in progress),
June 2010.
[9] Willis, D. and B. Hoeneisen, "Session Initiation Protocol (SIP)
Extension Header Field for Registering Non-Adjacent Contacts",
RFC 3327, December 2002.
[10] Willis, D. and B. Hoeneisen, "Session Initiation Protocol (SIP)
Extension Header Field for Service Route Discovery During
Registration", RFC 3608, October 2003.
[11] Rosenberg, J., "A Session Initiation Protocol (SIP) Event
Package for Registrations", RFC 3680, March 2004.
[12] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Indicating
User Agent Capabilities in the Session Initiation Protocol
(SIP)", RFC 3840, August 2004.
[13] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Caller
Preferences for the Session Initiation Protocol (SIP)",
RFC 3841, August 2004.
[14] Sparks, R., Hawrylyshen, A., Johnston, A., Rosenberg, J., and
H. Schulzrinne, "Session Initiation Protocol (SIP) Torture Test
Messages", RFC 4475, May 2006.
[15] Jennings, C., Mahy, R., and F. Audet, "Managing Client-
Initiated Connections in the Session Initiation Protocol
Roach Expires January 7, 2011 [Page 25]
Internet-Draft Globally Identifiable Number Routing July 2010
(SIP)", RFC 5626, October 2009.
[16] Rosenberg, J., "Obtaining and Using Globally Routable User
Agent URIs (GRUUs) in the Session Initiation Protocol (SIP)",
RFC 5627, October 2009.
[17] Kaliski, B., "TWIRL and RSA Key Size", May 2003.
Appendix A. Requirements Analysis
The document "Requirements for multiple address of record (AOR)
reachability information in the Session Initiation Protocol (SIP)"
[8] contains a list of requirements and desired properties for a
mechanism to register multiple AORs with a single SIP transaction.
This section evaluates those requirements against the mechanism
described in this document.
REQ1 - The mechanism MUST allow a SIP-PBX to enter into a trunking
arrangement with an SSP whereby the two parties have agreed on a set
of telephone numbers deemed to have been assigned to the SIP-PBX.
The requirement is satisfied.
REQ2 - The mechanism MUST allow a set of assigned telephone numbers
to comprise E.164 numbers, which can be in contiguous ranges,
discrete, or in any combination of the two.
The requirement is satisfied; the DIDs associated with a
registration is established by bilateral agreement between the SSP
and the SIP-PBX, and is not part of the mechanism described in
this document.
REQ3 - The mechanism MUST allow a SIP-PBX to register reachability
information with its SSP, in order to enable the SSP to route to the
SIP-PBX inbound requests targeted at assigned telephone numbers.
The requirement is satisfied.
REQ4 - The mechanism MUST NOT prevent UAs attached to a SIP-PBX
registering with the SIP-PBX on behalf of AORs based on assigned
telephone numbers in order to receive requests targeted at those
telephone numbers, without needing to involve the SSP in the
registration process.
The requirement is satisfied; in the presumed architecture, SIP-
PBX UAs register with the SIP-PBX, an require no interaction with
the SSP.
Roach Expires January 7, 2011 [Page 26]
Internet-Draft Globally Identifiable Number Routing July 2010
REQ5 - The mechanism MUST allow a SIP-PBX to handle internally
requests originating at its own UAs and targeted at its assigned
telephone numbers, without routing those requests to the SSP.
The requirement is satisfied; SIP-PBXes may recognize their own
DID and their own GRUUs, and perform on-SIP-PBX routing without
sending the requests to the SSP.
REQ6 - The mechanism MUST allow a SIP-PBX to receive requests to its
assigned telephone numbers originating outside the SIP-PBX and
arriving via the SSP, so that the SIP-PBX can route those requests
onwards to its UAs, as it would for internal requests to those
telephone numbers.
The requirement is satisfied
REQ7 - The mechanism MUST provide a means whereby a SIP-PBX knows
which of its assigned telephone numbers an inbound request from its
SSP is targeted at.
The requirement is satisfied. For ordinary calls and calls using
Public GRUUs, the DID is indicated in the user portion of the
Request-URI. For calls using Temp GRUUs constructed with the
mechanism described in Section 7.1.2, the "gr" parameter provides
a correlation token the SIP-PBX can use to identify which UA the
call should be routed to.
REQ8 - The mechanism MUST provide a means of avoiding problems due to
one side using the mechanism and the other side not.
The requirement is satisfied through the 'gin' option tag and the
'bnc' Contact parameter.
REQ9 - The mechanism MUST observe SIP backwards compatibility
principles.
The requirement is satisfied through the 'gin' option tag.
REQ10 - The mechanism MUST work in the presence of intermediate SIP
entities on the SSP side of the SIP-PBX-to-SSP interface (i.e.,
between the SIP-PBX and the SSP's domain proxy), where those
intermediate SIP entities need to be on the path of inbound requests
to the SIP-PBX.
The requirement is satisfied through the use of the Path mechanism
defined in RFC 3327 [9]
REQ11 - The mechanism MUST work when a SIP-PBX obtains its IP address
Roach Expires January 7, 2011 [Page 27]
Internet-Draft Globally Identifiable Number Routing July 2010
dynamically.
The requirement is satisfied by allowing the SIP-PBX to use an IP
address in the Bulk Number Contact URI contained in a REGISTER
Contact header field.
REQ12 - The mechanism MUST work without requiring the SIP-PBX to have
a domain name or the ability to publish its domain name in the DNS.
The requirement is satisfied by allowing the SIP-PBX to use an IP
address in the Bulk Number Contact URI contained in a REGISTER
Contact header field.
REQ13 - For a given SIP-PBX and its SSP, there MUST be no impact on
other domains, which are expected to be able to use normal RFC 3263
procedures to route requests, including requests needing to be routed
via the SSP in order to reach the SIP-PBX.
The requirement is satisfied by allowing the domain name in the
Request URI used by external entities to resolve to the SSP's
servers via normal RFC 3263 resolution procedures.
REQ14 - The mechanism MUST be able to operate over a transport that
provides integrity protection and confidentiality.
The requirement is satisfied; nothing in the proposed mechanism
prevent the use of TLS between the SSP and the SIP-PBX.
REQ15 - The mechanism MUST support authentication of the SIP-PBX by
the SSP and vice versa.
The requirement is satisfied; SIP-PBXes may employ either SIP
digest authentication or mutually-authenticated TLS for
authentication purposes.
REQ16 - The mechanism MUST allow the SIP-PBX to provide its UAs with
public or temporary Globally Routable UA URIs (GRUUs) [16].
The requirement is satisfied via the mechanisms detailed in
Section 7.1.
REQ17 - The mechanism MUST NOT preclude the ability of the SIP-PBX to
route on-SIP-PBX requests directly, without hair-pinning the
signaling through the SSP.
The requirement is satisfied; SIP-PBXes may recognize their own
DID and their own GRUUs, and perform on-SIP-PBX routing without
sending the requests to the SSP. (Note that this requirement
Roach Expires January 7, 2011 [Page 28]
Internet-Draft Globally Identifiable Number Routing July 2010
duplicates REQ5, and will probably be removed in a future version
of the requirements document.)
REQ18 - The mechanism MUST work over any existing transport specified
for SIP, including UDP.
The requirement is satisfied to the extent that UDP can be used
for REGISTER requests in general. The application of certain
extensions and/or network topologies may exceed UDP MTU sizes, but
such issues arise both with and without the mechanism described in
this document. This document does not exacerbate such issues.
DES1 - The mechanism SHOULD allow an SSP to exploit its mechanisms
for providing SIP service to ordinary subscribers in order to provide
a SIP trunking service to SIP-PBXes.
The desired property is satisfied; the routing mechanism described
in this document is identical to the routing performed for singly-
registered AORs.
DES2 - The mechanism SHOULD scale to SIP-PBX's of several thousand
assigned telephone numbers.
The desired property is satisfied; nothing in this document
precludes DID pools of arbitrary size.
DES3 - The mechanism SHOULD scale to support several thousand SIP-
PBX's on a single SSP.
The desired property is satisfied; nothing in this document
precludes an arbitrary number of SIP-PBXes from attaching to a
single SSP.
DES4 - The mechanism SHOULD require relatively modest changes to a
substantial population of existing SSP and SIP-PBX implementations,
in order to encourage a fast market adoption of the standardized
mechanism.
The desired property is difficult to evaluate in the context of
any solution. The mechanism proposed in this document uses the
REGISTER method, which is the method preferred by many existing
SIP-PBX deployments. The handling of request routing logic is
nearly identical to that of RFC 3261 proxy/registrars, allowing
implementors to leverage existing proxy/registrar code.
Roach Expires January 7, 2011 [Page 29]
Internet-Draft Globally Identifiable Number Routing July 2010
Author's Address
Adam Roach
Tekelec
17210 Campbell Rd.
Suite 250
Dallas, TX 75252
US
Email: adam@nostrum.com
Roach Expires January 7, 2011 [Page 30]