Network Working Group D. Fedyk Internet Draft Alcatel-Lucent Intended status: Standards Track P.Ashwood-Smith Expires: August 1, 2011 Huawei February 1, 2011 IS-IS Extensions Supporting IEEE 802.1aq Shortest Path Bridging draft-ietf-isis-ieee-aq-04.txt Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html This Internet-Draft will expire on August 1st 2011. Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Fedyk, et al. Expires August 2011 [Page 1] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Abstract 802.1aq Shortest Path Bridging (SPB) is being standardized by the IEEE as the next step in the evolution of the various spanning tree and registration protocols. 802.1aq allows for true shortest path forwarding in a mesh Ethernet network context utilizing multiple equal cost paths. This permits it to support much larger layer 2 topologies, with faster convergence, and vastly improved use of the mesh topology. Combined with this is single point provisioning for logical connectivity membership, which includes point-to-point, point-to-multi-point and multi-point-to-multipoint variations. This memo documents the IS-IS changes required to support this IEEE protocol and provides some context and examples. Fedyk, et al. Expires August, 2011 [Page 2] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Table of Contents 1. Introduction...................................................4 2. Terminology....................................................4 3. Conventions used in this document..............................5 4. 802.1aq Overview...............................................6 4.1. Multi Topology Support....................................8 4.2. Data Path SPBM - Unicast..................................8 4.3. Data Path SPBM - Multicast (Head End Replication).........9 4.4. Data Path SPBM - Multicast (Tandem Replication)...........9 4.5. Data Path SPBV Broadcast.................................11 4.6. Data Path SPBV Unicast...................................11 4.7. Data Path SPBV Multicast.................................12 5. SPBM Example..................................................12 6. SPBV Example..................................................14 7. SPB Supported Adjacency types.................................16 8. SPB IS-IS adjacency addressing................................16 9. IS-IS Area Address and SYSID..................................17 10. Level 1/2 Adjacency..........................................17 11. Shortest Path Default Tie Breaking...........................17 12. Shortest Path ECT............................................18 13. Hello (IIH) protocol extensions..............................19 13.1. SPB MCID sub-TLV........................................20 13.2. SPB Digest sub-TLV......................................21 13.3. SPB Base VLAN-Identifiers sub-TLV.......................23 14. Node information extensions..................................25 14.1. SPB Instance sub-TLV....................................25 14.1.1. SPB Instance Opaque ECT-ALGORITHM sub-TLV..........28 15. Adjacency information extensions.............................29 15.1. SPB Link Metric sub-TLV.................................29 15.1.1. SPB Adjacency Opaque ECT-ALGORITHM sub-TLV.........30 16. Service information extensions...............................31 16.1. SPBM Service Identifier and Unicast Address sub-TLV.....31 16.2. SPBV Mac Address sub-TLV................................33 17. Security Considerations......................................35 18. IANA Considerations..........................................36 19. References...................................................37 19.1. Normative References....................................37 19.2. Informative References..................................38 20. Acknowledgments..............................................38 21. Author's Addresses...........................................38 22. Intellectual Property Statement..............................39 23. Disclaimer of Liability......................................40 Fedyk, et al. Expires August, 2011 [Page 3] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 1. Introduction 802.1aq Shortest Path Bridging (SPB) [802.1aq] is being standardized by the IEEE as the next step in the evolution of the various spanning tree and registration protocols. 802.1aq allows for true shortest path forwarding in an Ethernet mesh network context utilizing multiple equal cost paths. This permits SPB to support much larger layer 2 topologies, with faster convergence, and vastly improved use of the mesh topology. Combined with this is single point provisioning for logical connectivity membership which includes point-to-point (E-LINE), point-to-multi-point (E-TREE) and multi-point-to-multipoint (E-LAN) variations. The control protocol for 802.1aq is IS-IS [IS-IS] augmented with a small number of TLVs and sub TLVs. This supports two Ethernet encapsulating data paths, 802.1ad (Provider Bridges) [PB] and 802.1ah (Provider Backbone Bridges) [PBB]. This memo documents those TLVs while providing some overview. Note that 802.1aq requires no state machine or other substantive changes to [IS-IS]. 802.1aq simply requires a new Network Layer Protocol Identifier (NLPID) and set of TLVs. In the event of confusion between this document and [IS-IS], [IS-IS] should be taken as authoritative. 2. Terminology In addition to well understood IS-IS terms, this memo uses terminology from IEEE 802.1 and introduces a few new terms: 802.1ad Provider Bridging (PB) - Q-in-Q encapsulation 802.1ah Provider Backbone Bridges (PBB), MAC-IN-MAC encapsulation 802.1aq Shortest Path Bridging (SPB) Base-VID VID used to identify a VLAN in management operations B-DA Backbone Destination Address 802.1ah PBB B-MAC Backbone MAC Address B-SA Backbone Source address in 802.1ah PBB header B-VID Backbone VLAN ID in 802.1ah PBB header B-VLAN Backbone Virtual LAN BridgeID 64 bit quantity = (Bridge Priority:16)<<48 | SYSID:48 BridgePriority 16 bit relative priority of a node for tie breaking C-MAC Customer MAC. Inner MAC in 802.1ah PBB header C-VID Customer VLAN ID C-VLAN Customer Virtual LAN DA Destination Address Fedyk, et al. Expires August, 2011 [Page 4] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 ECT-ALGORITHM 32 bit unique id of an SPF tie breaking set of rules. ECT-MASK 64 bit mask XORed with BridgeID during tie breaking. E-LAN Bidirectional Logical Connectivity between >2 UNIs. E-LINE Bidirectional Logical Connectivity between two UNIs. E-TREE Asymmetric Logical Connectivity between UNIs. FDB Filtering Database: {DA/VID}->{next hops} I-SID Logical Grouping Identifier for E-LAN/LINE/TREE UNIs. LAN Local Area Network LSDB Link State Database LSP Link State Packet MAC-IN-MAC Ethernet in Ethernet framing as per 802.1ah[PBB] MDT Multicast Distribution Tree MMRP Multiple Mac Registration Protocol 802.1ak[MMRP] MT-ISIS Multi Topology IS-IS as used in [MT] MT Multi Topology. As used in [MT] MT-ID Multi Topology Identifier (12 bits). As used in [MT] NLPID Network Layer Protocol Identifier: IEEE 802.1aq= 0xC1 Q-in-Q Additional S-VLAN after a C-VLAN (802.1ad)[PB] PBB Provider Backbone Bridge - forwards using PBB Ingress Check Source Forwarding Check - drops misdirected frames (S,G) Source & Group - identity of a source specific tree (*,G) Any Source & Group - identity of a shared tree SA Source Address. SPB Shortest Path Bridging - generally all of 802.1aq. SPB Shortest Path Bridge - device implementing 802.1aq. SPB-instance Logical SPB instance correlated by MT-ID. SPBM Device implementing SPB MAC mode SPBV Device implementing SPB VID mode SPT Shortest Path Tree computed by one ECT-ALORITHM SPSourceID 20 bit identifier of the source of multicast frames. SPVID SPBV: a C-VLAN or S-VLAN that identifies the source. UNI User Network Interface: Customer to SPB attach point. VID VLAN ID 12 bit logical identifier after MAC header. VLAN Virtual LAN: A logical network in the control plane 3. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. The lower case forms "must", "must not", "shall", "shall not", "should", "should not" and "may" in this document are to be interpreted in the sense defined in [RFC2119], but are used where Fedyk, et al. Expires August, 2011 [Page 5] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 the normative behavior is defined in documents published by SDOs other than the IETF. 4. 802.1aq Overview This section provides an overview of the behavior of [802.1aq] and is not intended to be interpreted as normative text. For the definitive behavior the reader should consult [802.1aq]. Nonetheless lower case forms of the conventions in RFC2119 are used in this section to give the reader an indication of the intended normative behaviors as above. 802.1aq utilizes 802.1Q based Ethernet bridging. The filtering database (FDB) is populated as a consequence of the topology computed from the IS-IS database. For the reader unfamiliar with IEEE terminology, the definition of Ethernet behavior is almost entirely in terms of "filtering" (of broadcast traffic) rather than "forwarding" (the explicit direction of unicast traffic). This document uses the generic term "forwarding", and it has to be understood that these two terms simply represent different ways of expressing the same behaviors. 802.1aq supports multiple modes of operation depending on the type of data plane and the desired behavior. For the initial two modes of 802.1aq (SPBV and SPBM), routes are shortest path, are forward and reverse path symmetric with respect to any source / destination pair within the SPB domain, and are congruent with respect to unicast and multicast. Hence the shortest path tree (SPT) to a given node is congruent with the multicast distribution tree (MDT) from a given node. The MDT for a given VLAN is a pruned subset of the complete MDT for a given node which is identical to its SPT. Symmetry and congruency preserve packet ordering and proper fate sharing of OAM flows by the forwarding path. Such modes are fully supported by existing [802.1ag] and [Y.1731] OA&M mechanisms. VLANs provide a natural delineation of service instances. 802.1aq supports two modes, SPB VID (SPBV) and SPB MAC (SPBM). In SPBV multiple VLANS can be used to distribute load on different shortest path trees (each computed by a different tie breaking rule) on a service basis. In SPBM service instances are delineated by I-SIDs but VLANs again can be used to distribute load on different shortest path trees. Fedyk, et al. Expires August, 2011 [Page 6] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 There are two encapsulation methods supported. SPBM can be used in a PBB network implementing PBB (802.1ah [PBB]) encapsulation. SPBV can be used in PB networks implementing VLANs, PB (802.1aq [PB]) or PBB encapsulation. The two modes can co-exist simultaneously in an SPB network. The practical design goals for SPBV and SPBM in the current 802.1aq specification are networks of size 100 nodes and 1000 nodes respectively. However since SPBV can be sparsely used in an SPB Region it can simply span a large SPB region with a small number of SPVIDs. In SPBM and SPBV each bridge has at least one unique "known" MAC address which is advertised by IS-IS in the SYS-ID. In the forwarding plane, SPBM uses the combination of one or more B- VIDs and "known" Backbone-MAC (B-MAC) addresses that have been advertised in IS-IS. The term Backbone simply implies an encapsulation that is often used in the backbone networks, but the encapsulation is useful in other types of networks where hiding C- MACs is useful. The SPBM filtering database (FDB) is computed and installed for unicast and multicast MAC addresses, while the SPBV filtering database is computed and installed for unidirectional VIDs (referred to as SPVIDs), after which MAC reachability is learned (exactly as in bridged Ethernet) for unicast MACs. Both SPBV and SPBM use source specific multicast trees. If they share the same ECT-ALGORITHM (32 bit world wide unique definition of the computation) the tree is the same SPT. For SPBV (S,G) is encoded by a source-specific VID (the SPVID) and a standard Group MAC address. For SPBM (S,G) is encoded in the destination B-MAC address as the concatenation of a 20 bit SPB wide unique nodal nickname (referred to as the SPSourceID) and the 24 bit I-SID together with the B-VID which corresponds to the ECT-ALGORITHM network wide. 802.1aq supports membership attributes which are advertised with the I-SID (SPBM) or Group Address (SPBV) that define the group. Individual members can be transmitters (T) and/or receivers (R) within the group and the multicast state is appropriately sized to these requests. Multicast group membership is possible even without transmit membership by performing head end replication to the receivers thereby eliminating transit multicast state entirely. Some highly connected mesh networks provide for path diversity by offering multiple equal cost alternatives between nodes. Since Fedyk, et al. Expires August, 2011 [Page 7] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 congruency and symmetry must be honored, a single tree may leave some links under utilized. By using different deterministic tie breakers, up to sixteen shortest paths of arbitrary diversity are possible between any pair of nodes. This distributes the traffic on a VLAN basis. SPBV and SPBM may share a single SPT with a single ECT-ALGORITHM or use any combination of the 16 ECT-ALGORITHMs. An extensible framework permits additional or alternative algorithms with other properties and parameters (e.g. ECMP, (*,G) ) to also be supported without any changes in this or the IEEE documents. 4.1. Multi Topology Support SPB incorporates the multi topology features of [MT] thereby allowing multiple logical SPB instances within a single IS-IS instance. To accomplish this, all SPB related information is either explicitly or implicitly associated with a Multi Topology Identifier (MT-ID). SPB information related to a given MT-ID thus forms a single logical SPB instance. Since SPB has its own adjacency metrics and those metrics are also associated with an MT-ID it is not only possible to have different adjacency metrics (or infinite metrics) for SPB adjacencies, distinct from IP or other NLPIDs riding in this IS-IS instance, and also distinct from those used by other SPB instances in the same IS- IS instance. Data plane traffic for a given MT-ID is intrinsically isolated by the VLANs assigned to the SPB instance in question. Therefore VLANs (represented by VIDs in TLVs and data plane) must not overlap between SPB instances (regardless of how the control planes are isolated). The [MT] mechanism when applied to SPB allows different routing metrics and topology subsets for different classes of services. The use of [MT] other than the default MT-ID#0 is completely optional. The use of [MT] to separate SPB from other NLPIDs is also optional. 4.2. Data Path SPBM - Unicast Unicast frames in SPBM are encapsulated as per 802.1ah [PBB]. A Backbone Source Address (B-SA), Backbone Destination Address (B-DA), Backbone VLAN ID (B-VID) and an I-Component Service Instance ID (I- Fedyk, et al. Expires August, 2011 [Page 8] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 TAG) are used to encapsulate the Ethernet frame. The B-SA is a B-MAC associated with the ingress 802.1aq bridge, usually the "known" B- MAC of that entire bridge. The B-DA is one of the "known" B-MACs associated with the egress 802.1aq bridge. The B-VID and I-TAG are mapped based on the physical or logical UNI port (untagged, or tagged either by S-TAG or C-TAG) being bridged. Normal learning and broadcast to unknown C-MACs is applied as per [PBB] at the ingress/egress SPBs only. Unlike [PBB] on a (*,G) tree, the B-DA forwarding on tandem nodes (NNI to NNI) is performed without learning. Instead the output of 802.1aq computations, based on the TLVs specified in this document, are used to populate the filtering data bases (FDB). The FDB entries map {B-DA, B-VID} to an outgoing interface and are only populated from the IS-IS database and computations. The B-SA/B-VID is checked on tandem nodes against the ingress port. If the B-SA/B-VID (as a destination) entry in the FDB does not point to the port on which the packet arrived the packet is discarded. This is referred to as an Ingress Check and serves as a very powerful loop mitigation mechanism. 4.3. Data Path SPBM - Multicast (Head End Replication) Head end replication is supported for instances where there is a sparse community of interest or a low likelihood of multicast traffic. Head end replication requires no Multicast state in the core. A UNI port wishing to use head end replication must not advertise its I-SID membership with the TX bit set but instead must locally and dynamically construct the appropriate unicast serial replication to all the other receivers (RX) of the same I-SID. When an unknown customer unicast or a multicast frame arrives at an SPBM User to Network Interface (UNI) port which has been configured to replicate only at the head end the packet is replicated once for each receiver, encapsulated and sent as a unicast frame. The set of receivers is determined by inspecting the IS-IS database for other SPBs that have registered interest in the same I-SID with the RX (receive) attribute set. This RX/I-SID pair is found in the SPBM Service Identifier and Unicast Address sub-TLV. The packets are encapsulated as per the SPBM Unicast forwarding above. 4.4. Data Path SPBM - Multicast (Tandem Replication) Tandem replication uses the Shortest path Tree to replicate Frames only where the tree forks and there is at least one receiver on each branch. Tandem replication is bandwidth efficient but uses multicast Fedyk, et al. Expires August, 2011 [Page 9] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 FDB entries (state) in core bridges which might be unnecessary if there is little multicast traffic demand. The head end replication mode is best suited for the case where there is little or no true multicast traffic for an I-SID. Tandem replication is triggered on transit nodes when the I-SID is advertised with the TX bit set. Broadcast, unknown unicast or multicast frames arriving at an SPBM UNI port are encapsulated with a B-DA multicast address which uniquely identifies the encapsulating node (the root of the Multicast Distribution Tree) and the I-SID scoping this multicast. This B-DA address is a well formed multicast group address (as per 802.1Q and 802.1ah) which concatenates the SPSourceID A' with the I- SID M (written as DA= and uniquely identifying the (S,G) tree). This exact format is given in Figure 1 below: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 M L TYP +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1|1|0|0| SPSRC [8:19] | SPSRC [0:7] | ISID [16:23] | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ISID [8:15] | ISID [0:7] | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1 SPBM Multicast Address format o M is the multicast bit- always set to 1 for a multicast DA. o L is the local bit- always set to 1 for a SPBM constructed multicast DA. o TYP is the SPSourceID type. Two values are supported. 00 for statically assigned SPSourceID's and 01 for dynamic assignment. o SPSRC (SPSourceID) is a 20 bit quantity that uniquely identifies a SPBM node for all B-VIDs allocated to SPBM operation. This is just the SPSourceID advertised in the SPB Instance sub-TLV. o I-SID is the 24 bit I component Service ID advertised in the SPBM Service Identifier TLV. It occupies the lower 24 bits of the SPBM multicast DA. The I-SID value 0xfff is reserved for SPBM control traffic(refer to the default I-SID in [802.1aq]). Fedyk, et al. Expires August, 2011 [Page 10] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 This multicast address format is used as the DA on frames when they are first encapsulated at ingress to the SPBM network. The DA is also installed into the FDBs on all SPBM nodes that are on the corresponding SPT between the source and other nodes that have registered receiver interest in the same I-SID. Just as with unicast forwarding, the B-SA/B-VID may be used to perform an ingress check, but the SPSourceID encoded in the DA and the "drop-on-unknown" functionality of the FDB in [PBB] achieve the same effect. The I-Component at the egress SPBM device has completely standard [PBB] behavior and therefore will: 1) learn the remote C-SA to B-SA relationship and 2) bridge the original customer frame to the set of local UNI ports that are associated with the I-SID. 4.5. Data Path SPBV Broadcast When a packet for an unknown DA arrives at a SPBV UNI port VID translation (or VID encapsulation for un-tagged Frames) with the corresponding SPVID for this VLAN and ingress SPB is performed. SPVID forwarding is simply an SPT that follows normal VLAN forwarding behavior, with the exception that the SPVID is unidirectional. As a result shared learning (SVL) is used between the forward and reverse path SPVIDs associated with the same Base- VID to allow SPBV unicast forwarding to operate in the normal reverse learning fashion. Ingress check is done by simply verifying that the bridge to which the SPVID has been assigned is indeed "shortest path" reachable over the link over which the packet tagged with that SPVID arrived. This check is computed from the IS-IS database and is implied when the SPVID is associated with a specific incoming port. 4.6. Data Path SPBV Unicast Conversely when a packet for a known DA arrives at a SPBV UNI port VID translation (or VID encapsulation for un-tagged Frames) with the corresponding SPVID for this VLAN and ingress SPB is performed. Since the SPVID will have been configured to follow a source specific SPT and the DA is known the packet will follow the source specific path towards the destination C-MAC. Fedyk, et al. Expires August, 2011 [Page 11] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Ingress check is as per the previous SPBV section. 4.7. Data Path SPBV Multicast C-DA multicast addresses may be advertised from SPBV UNI ports. These may be configured or learned through MMRP. The MMRP protocol is terminated at the edge of the SPBV network and IS-IS carries the multicast addresses. Tandem SPBV devices will check to see if they are on the SPF tree between SPBV UNI ports advertising the same C-DA multicast address, and if so will install multicast state to follow the SPBV SPF trees. Ingress check is as per the previous two SPBV sections. 5. SPBM Example Consider the following small example network shown in Figure 2. Nodes are drawn in boxes with the last nibble of their B-MAC address :1..:7, the rest of the B-MAC address nibbles are 4455-6677-00xx. Links are drawn as -- and / while the interface indexes are drawn as numbers next to the links. UNI ports are shown as <==> with the desired I-SID show at the end of the UNI ports as i1. +----+ +----+ | :4 | 2 ------1 | :5 | <==> i1 +----+ +----+ 1 3 3 2 / \ / \ 1 4 3 2 +----+ +----+ +----+ i1 <==> | :1 | 2----1 | :2 | 2------1 | :3 | <==> i1 +----+ +----+ +----+ 3 6 5 3 \ / \ / 3 2 1 2 +----+ +----+ | :6 | 1-------3 | :7 | <==> i1 +----+ +----+ Figure 2 - SPBM Example 7 node network Using the default ECT-ALGORITHM (00-80-C2-01), which picks the equal cost path with the lowest BridgeID, this ECT-ALGORITHM is assigned to B-VID 100. When all links have the same cost, then the 1 hop shortest paths are all direct and the 2 hop shortest paths (which are of course symmetric) are as follows: Fedyk, et al. Expires August, 2011 [Page 12] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 { 1-2-3, 1-2-5, 1-2-7, 6-2-5, 4-2-7, 4-1-6, 5-2-7, 6-2-3, 4-2-3 } Node :1's Unicast forwarding table therefore routes toward B-MACs :7, :3 and :5 via interface/2 while its single hop paths are all direct as can be seen from its FDB given in Figure 3. Node :1 originates multicast since it is at the head of the MDT to nodes :3, :5 and :7 and is a transmitter of I-SID 1 which nodes :3, :5 and :7 all wish to receive. Node :1 therefore produces a multicast forwarding entry who's DA contains its SPSourceID (in the example the last 20 bits of the B-MAC) and the I-SID 1 and sends to interface 2 with B-VID=100. Node :1's full unicast(U) and multicast(M) table is shown in Figure 3. Note that the IN/IF (incoming interface) field is not specified for unicast traffic and for multicast traffic has to point back to the root of the tree, unless it is the head of the tree in which case we use the convention if/OO. Since Node :1 is not transit for any multicast it only has a single entry for the root of its tree for I-SID=1. +-------+-------------------+------+-----------------+ | IN/IF | DESTINATION ADDR | BVID | OUT/IF(s) | +-------+-------------------+------+-----------------+ U| if/** | 4455-6677-0002 | 0100 | {if/2 } U| if/** | 4455-6677-0003 | 0100 | {if/2 } U| if/** | 4455-6677-0004 | 0100 | {if/1 } U| if/** | 4455-6677-0005 | 0100 | {if/2 } U| if/** | 4455-6677-0006 | 0100 | {if/3 } U| if/** | 4455-6677-0007 | 0100 | {if/2 } M| if/00 | 7300-0100-0001 | 0100 | {if/2 } Figure 3 - SPBM Node :1 FDB - Unicast(U) and Multicast(M) Node :2, being at the center of the network, has direct 1 hop paths to all other nodes, therefore its unicast FDB simply sends packets with the given B-MAC/B-VID=100 to the interface directly to the addressed node. This can be seen by looking at the unicast entries (the first 6) shown in Figure 4. Fedyk, et al. Expires August, 2011 [Page 13] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 +-------+-------------------+------+-----------------+ | IN/IF | DESTINATION ADDR | BVID | OUT/IF(s) | +-------+-------------------+------+-----------------+ U| if/** | 4455-6677-0001 | 0100 | {if/1 } U| if/** | 4455-6677-0003 | 0100 | {if/2 } U| if/** | 4455-6677-0004 | 0100 | {if/4 } U| if/** | 4455-6677-0005 | 0100 | {if/3 } U| if/** | 4455-6677-0006 | 0100 | {if/6 } U| if/** | 4455-6677-0007 | 0100 | {if/5 } M| if/01 | 7300-0100-0001 | 0100 | {if/2,if/3,if/5 } M| if/02 | 7300-0300-0001 | 0100 | {if/1 } M| if/03 | 7300-0500-0001 | 0100 | {if/1,if/5 } M| if/05 | 7300-0700-0001 | 0100 | {if/1,if/3 } Figure 4 - SPBM Node :2 FDB Unicast(U) and Multicast(M) Node :2's multicast is more complicated since it is a transit node for the 4 members of I-SID=1, therefore it requires 4 multicast FDB entries depending on which member it is forwarding/replicating on behalf of. For example, node :2 is on the shortest path between each of nodes {:3,:5,:7} and :1. So it must replicate from node :1 I-SID 1 out on interfaces 2, 3 and 5 (to reach nodes :3, :5 and :7). It therefore creates a multicast DA with the SPSourceID of node :1 together with I-SID=1 which it expects to receive over interface/1 and will replicate out interfaces/{2, 3 and 5}. This can be seen in the first multicast entry in Figure 4. Note that node :2 is not on the shortest path between nodes :3 and :5 nor between nodes :3 and :7, however it still has to forward packets to node :1 from node :3 for this I-SID, which results in the second multicast forwarding entry in Figure 4. Likewise for packets originating at nodes 5 or 7, node :2 only has to replicate twice, which results in the last two multicast forwarding entries in Figure 4. 6. SPBV Example Using the same example network as Figure 2, we will look at the FDBs produced for SPBV mode forwarding. Nodes :1, :5, :3 and :7 wish to transmit and receive the same multicast MAC traffic using multicast address 0300-0000-000f and at the same time require congruent and symmetric unicast forwarding. In SPBV mode the only encapsulation is the C or S-TAG and the MAC addresses SA,DA are reverse-path learned, as in traditional bridging. Fedyk, et al. Expires August, 2011 [Page 14] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 +----+ +----+ | :4 | 2 ------1 | :5 | <==> MMAC ..:f +----+ +----+ 1 3 3 2 / \ / \ 1 4 3 2 +----+ +----+ +----+ MMAC<==> | :1 | 2----1 | :2 | 2------1 | :3 | <==> MMAC ..:f ..:f +----+ +----+ +----+ 3 6 5 3 \ / \ / 3 2 1 2 +----+ +----+ | :6 | 1-------3 | :7 | <==> MMAC ..:f +----+ +----+ Figure 5 - SPBV Example 7 node network Assuming the same ECT-ALGORITHM (00-80-C2-01), which picks the equal cost path with the lowest BridgeID, this ECT-ALGORITHM is assigned to Base-VID 100, and for each node the SPVID = Base-VID + Node Id (i.e. 101, 102..107). When all links have the same cost, then the 1 hop shortest paths are all direct and the 2 hop shortest paths (which are of course symmetric) are as previously given for Figure 2. Node :1's SPT (Shortest Path Tree) for this ECT-ALGORITHM is therefore (described as a sequence of unidirectional paths): { 1->4, 1->6, 1->2->3, 1->2->5, 1->2->7 } The FDBs therefore must have entries for the SPVID reserved for packets originating from node :1 which in this case is VID=101. Node :2 therefore has a FDB which looks like Figure 6. In particular it takes packets from VID 101 on interface/01 and sends to nodes :3, :5 and :7 via if/2, if/3 and if/5. It does not replicate anywhere else because the other nodes :4 and :6 are reached by the SPT directly from node :1. The rest of the FDB unicast entries follow a similar pattern; recall that the shortest path between :4 and :6 is via node :1, which explains replication onto only two interfaces from if/4 and if/6. Note that the destination addresses are wild cards and shared VLAN learning (SVL) exists between these SPVIDs, because they are all associated with BASE VID = 100, which defines the VLAN being bridged. Fedyk, et al. Expires August, 2011 [Page 15] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 +-------+-------------------+------+-----------------+ | IN/IF | DESTINATION ADDR | VID | OUT/IF(s) | +-------+-------------------+------+-----------------+ U| if/01 | ************** | 0101 | {if/2,if/3,if/5 } U| if/02 | ************** | 0103 | {if/1,if/4,if/6 } U| if/04 | ************** | 0104 | {if/2,if/5 } U| if/03 | ************** | 0105 | {if/1,if/5,if/6 } U| if/06 | ************** | 0106 | {if/2,if/3 } U| if/05 | ************** | 0107 | {if/1,if/3,if/4 } Figure 6 - SPBV Node :2 FDB unicast Now, since nodes :5, :3, :7 and :1 are advertising membership in the same multicast group address :f, Node 2 requires additional entries to replicate just to these specific nodes for the given multicast group address. These additional multicast entries are given below in Figure 7. +-------+-------------------+------+-----------------+ | IN/IF | DESTINATION ADDR | VID | OUT/IF(s) | +-------+-------------------+------+-----------------+ M| if/01 | 0300-0000-000f | 0101 | {if/2,if/3,if/5 } M| if/02 | 0300-0000-000f | 0103 | {if/1 } M| if/03 | 0300-0000-000f | 0105 | {if/1,if/5 } M| if/05 | 0300-0000-000f | 0107 | {if/1,if/3 } Figure 7 - SPBV Node :2 FDB Multicast(M) 7. SPB Supported Adjacency types IS-IS for SPB currently only supports P2P adjacencies. Other link types are for future study. As a result pseudonodes and links to/from pseudonodes are not considered as part of the IS-IS SPF computations and will be avoided if present in the physical topology. Other NLPIDs MAY of course use them as per normal. IS-IS for SPB must use the IS-IS Three-Way handshake for IS-IS Point-to-Point Adjacencies described in RFC 5303. 8. SPB IS-IS adjacency addressing The default behavior of 802.1aq is to use the normal IS-IS Ethernet multicast addresses for IS-IS. There are however additional Ethernet multicast addresses that have been assigned for 802.1aq for special use cases. These do not in Fedyk, et al. Expires August, 2011 [Page 16] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 anyway change the state machinery or packet formats of IS-IS but simply recommend and reserve different multicast addresses. Refer to [802.1aq] for additional details. 9. IS-IS Area Address and SYSID A stand-alone implementation (supporting ONLY the single NLPID=0xC1) of SPB must use an IS-IS area address value of 0 and the SYSID must be the well known MAC address of the SPB device. Non stand-alone implementations (supporting other NLPIDs) MUST use the normal IS-IS rules for the establishment of a level 1 domain (i.e. multiple area addresses are allowed but where immediate adjacencies share a common area address). Level 2 operations of course place no such restriction on adjacent area addresses. 10. Level 1/2 Adjacency SPBV and SPBM will operate either within an IS-IS level 1, or an ISIS level 2. As a result, the TLVs specified here MAY propagate either in level 1 or level 2 LSPs. IS-IS SPB implementations must support level 1 and may support level 2 operations. Hierarchical SPB is for further study therefore these TLV's should not be leaked between level 1 and level 2. 11. Shortest Path Default Tie Breaking (ECT-ALGORITHM = 00-80-C2-01) Two mechanisms are used to ensure symmetry and determinism in the shortest path calculations. The first mechanism addresses the problem when different ends (nodes) of an adjacency advertise different values for the SPB-LINK- METRIC. To solve this SPB shortest path calculations must use the maximum value of the two node's advertised SPB-LINK-METRICs when accumulating and minimizing the (sub)path costs. The second mechanism addresses the problem when two equal sums of link metrics (sub)paths are found. To solve this, the (sub)path with the fewest hops between the fork/join points must win the tie. However, if both (sub)paths have the same number of hops between the fork and join points then the default tie breaking must pick the path traversing the intermediate node with the lower BridgeID. The BridgeID is an 8 byte quantity whose upper 2 bytes are the node's BridgePriority and the lower 6 bytes are the node's SYSID. Fedyk, et al. Expires August, 2011 [Page 17] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 For example, consider the network in Figure 2 when a shortest path computation is being done from node :1. Upon reaching node :7 two competing sub-paths fork at node :1 and join at node :7. The first via :2 and the second via :6. Assuming that all the nodes advertise a Bridge Priority of 0, the default tie breaking rule causes the path traversing node :2 to be selected since it has a lower BridgeID {0...:2} than node :6 {0...:6}. Note that the operator may cause the tie breaking logic to pick the alternate path by raising the Bridge Priority of node :2 above that of node :6. The above algorithm guarantees symmetric and deterministic results in addition to having the critical property of transitivity (shortest path is made up of sub-shortest paths). 12. Shortest Path ECT (ECT-ALGORITHMs = 00-80-C2-01 .. 00-80-C2-10) To create diversity in routing SPB defines 16 variations on the above default tie breaking algorithm, these have world wide unique designations 00-80-C2-01 through 00-80-C2-10. These designations consist of the IEEE 802.1 OUI value 00-80-C2 concatenated with indexes 0X01..0X10. These individual algorithms are implemented by selecting the (sub) path with the lowest value of: XOR BYTE BY BYTE(ECT-MASK{ECT-ALGORITHM.index},BridgeID) Where: ECT-MASK{17} = { 0x00, 0x00, 0xFF, 0x88, 0x77, 0x44, 0x33, 0xCC, 0xBB, 0x22, 0x11, 0x66, 0x55, 0xAA, 0x99, 0xDD, 0xEE }; XOR BYTE BY BYTE - XORs BridgeID bytes with ECT-MASK ECT-MASK{1} since it xor's with all 0's is just the same as the default algorithm described above 00-80-C2-01, while ECT-MASK{0x02} since it xor's with a mask of all 1's will invert the BridgeID essentially picking the path traversing the largest Bridge ID. The other ECT-MASKs produce diverse alternatives. In all cases the BridgePriority, since it is the most significant part of the BridgeID permits overriding the SYSID as the selection criteria and gives the operator a degree of control on the chosen ECT paths. Fedyk, et al. Expires August, 2011 [Page 18] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 To support many other tie breaking mechanisms in the future two opaque ECT TLV's are defined which may be used to provide parameters to ECT-ALGORITHMS outside of the currently defined space. ECT-ALGORITHMS are mapped to VIDs and then services can be assigned to those VIDs. This permits a degree of traffic engineering since service assignment to VID is consistent end to end through the network. 13. Hello (IIH) protocol extensions IEEE 802.1aq can run in parallel with other Network Layer Protocols such as IPV4 and IPV6, therefore failure for two SPB nodes to establish an adjacency MUST NOT cause rejection of an adjacency for the purposes of other Network Layer Protocols. IEEE 802.1aq has been assigned the NLPID value 0xC1 [NLPID] which MUST be used by shortest path bridges (SPBs) to indicate their ability to run 802.1aq. This is done by including this NLPID value in the IS-IS IIH PDU Protocols Supported TLV (type 129). 802.1aq frames MUST only flow on adjacencies that advertise this NLPID in both directions of the IIH PDUs. 802.1aq computations MUST consider an adjacency that has not advertised 0xC1 NLPID in both directions as non-existent (infinite link metric) and MUST ignore any IIH SPB TLV's they receive over such adjacencies. IEEE 802.1aq augments the normal IIH PDU with three new TLV's which like all other SPB TLVs travel within multi topology [MT] TLVs, therefore allowing multiple logical instances of SPB within a single IS-IS protocol instance. Since SPB can use many VIDs and must agree on which VIDs are used for which purposes, the IIH PDU's carry a digest of all the used VIDs (on the NNI's) referred to as the SPB-MCID TLV which uses a common and compact encoding taken reused from 802.1Q. SPB neighbors may support an optional mechanism to verify that the contents of their topology databases are synchronized (for the purposes of loop prevention). This is done by exchanging a digest of SPB topology information (computed over all MTIDS) and taking specific actions on forwarding entries when the digests indicate a mismatch in topology. This digest is carried in the optional SPB Digest sub-TLV. Fedyk, et al. Expires August, 2011 [Page 19] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Finally SPB needs to know which SPT sets (defined by ECT-ALGORITHMS) are being used by which VIDs, and this is carried in the Base VLAN Identifiers sub-TLV. 13.1. SPB MCID sub-TLV This sub-TLV is added to an IIH PDU to indicate the digest for the Multiple spanning tree configuration a.k.a MCID. This TLV is a digest of local configuration of which VIDs are running which protocols. (The information is not to the level of a specific algorithm in the case of SPB). This information should be the same on all bridges in the topology identified by the MT-Port-Cap TLV [LAYER2] it is being carried within. The data used to generate the MCID is populated by configuration and is a digest of the VIDs allocated to various protocols. Two MCIDs are carried to allow non disruptive transitions between configurations when the changes are non-critical. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type=SPB-MCID | = 6 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MCID (51 Bytes) | | ............... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Aux MCID (51 Bytes) | | ............... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type = 6 (Pending IANA). o Length: The size of the value defined below (102). Fedyk, et al. Expires August, 2011 [Page 20] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o MCID (51-bytes) The complete MCID defined in IEEE 802.1Q which identifies an SPT Region on the basis of matching assignments of VIDs to control regimes (xSTP, SPBV, SPBM, etc). Briefly, the MCID consists of a 1 byte format selector, a 32 byte configuration name, a 2 byte revision level and finally a 16 byte signature of type HMAC-MD5 over an array of 4096 elements that contain identifiers of the use of the corresponding VID. Refer to section 13.8 of [802.1aq] for the exact format and procedure. Note that the use of the VID does not include specification of a specific SPB ECT-ALGORITHM, rather it is coarser grain. o Aux MCID (51-bytes) The complete MCID defined in IEEE 802.1Q which identifies an SPT Region. The aux MCID allows SPT Regions to be migrated by the allocation of new VLAN to FDB Mappings without interruption to existing traffic. The SPB MCID sub-TLV is carried within the MT-Port-Cap TLV [LAYER2] which in turn is carried in an IIH PDU. 13.2. SPB Digest sub-TLV This sub-TLV is optionally added to an IIH PDU to indicate the current SPB topology digest value. It is always carried in an MT- Port-Cap TLV [LAYER2] with an MT-ID value of 0. This information should settle to be the same on all bridges in an unchanging topology. Matching digests indicate (with extremely high probability) that the topology view between two SPBs is synchronized, and is used to control the updating of forwarding information. The SPB Agreement Digest is computed based on contributions derived from the current topologies of all SPB MT instances, and is designed to change when significant topology changes occur within any SPB instance. During the propagation of LSPs the Agreement Digest may vary between neighbors until the key topology information in the LSPs are common. The digest is therefore a summarized means of determining agreement between nodes on database commonality, and hence infer agreement on the distance to all multicast roots. When present it is used for loop prevention as follows: For each shortest path tree where it has been determined the distance to the root has changed, "unsafe" multicast forwarding is blocked until the exchanged Agreement Digests match while "safe" multicast forwarding is allowed to continue despite the disagreement in digests and hence topology views. [802.1aq] section 28.2 defines in detail what constitutes "safe" vs. "unsafe". Fedyk, et al. Expires August, 2011 [Page 21] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type=SPB-Digest| = 7 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-----+-+---+---+ | Res |V| A | D | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Agreement Digest (Length - 1) | | ............... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type = 7 (Pending IANA). o Length: The size of the value. o V - agreed digest valid bit. See [802.1aq] Sec 28.2. o A (2 bits) The Agreement Number 0-3 which aligns with BPDUs Agreement Number concept [802.1aq]. When the Agreement Digest for this node changes this number is incremented. The node then checks for Agreement Digest match (as below). The new local Agreement Number and the updated local Discarded Agreement Number are then transmitted with the new Agreement Digest to the node's neighbors in the hello PDU. Once an Agreement Number has been sent it is considered outstanding until a matching or more recent Discarded Agreement Number is received from the neighbor. o D (2 bits) The Discarded Agreement Number 0-3 which aligns with BPDUs Agreement Number concept. When an Agreement Digest is received from a neighbor, this number is set to the received Agreement Number, to signify that this node has received this new agreement and discarded any previous ones. The node then checks whether the local and received Agreement Digests match. If they do, this node then sets : the local Discarded Agreement Number = received Agreement Number + 1 If the Agreement Digests match, AND received Discarded Agreement Number == local Agreement Number + N (N = 0 || 1) then the node has a topology matched to its neighbor. Fedyk, et al. Expires August, 2011 [Page 22] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Whenever the local Discarded Agreement Number relating to a neighbor changes, the local Agreement Digest, Agreement Number, and Discarded Agreement Number are transmitted. o Agreement Digest. This digest is used to determine when SPB is synchronized between neighbors for all SPB instances. The agreement digest is a hash computed over the set of all SPB adjacencies in all SPB instances. In other words, the digest includes all VIDs and all adjacencies for all MT instances of SPB (but not other network layer protocols). This reflects the fact that all SPB nodes in a region must have identical VID allocations (see 13.1), and so all SPB instances will contain the same set of nodes. The size and exact procedure for computing the Agreement Digest is defined in section 28.2 of [802.1aq]. The SPB Digest sub-TLV is carried within the MT-Port-Cap TLV [LAYER2] (with the MT-ID value 0) which in turn is carried in an IIH PDU. When supported, this sub-TLV MUST be carried on every IIH between SPB neighbors, not just when a Digest changes. When one peer supports this TLV and the other does not, loop prevention by digest agreement must not be done by either side. 13.3. SPB Base VLAN-Identifiers sub-TLV This sub-TLV is added to an IIH PDU to indicate the mappings between ECT algorithms and Base-VIDs (and by implication the VID(s) used on the forwarding path for each SPT Set for a VLAN identified by a Base VID) that are in use. Under stable operational conditions, this information should be the same on all bridges in the topology identified by the MT-Port-Cap TLV [LAYER2] it is being carried within. Fedyk, et al. Expires August, 2011 [Page 23] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type= SPB-B-VID| = 8 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-----------------------------------------------+ | ECT - VID Tuple (1) (6 bytes) | +---------------------------------+-----------------------------+ | ... | ECT-VID Tuple(2) (6 bytes) | +---------------------------------+-----------------------------+ | ..... | +---------------------------------------------------------------+ | ..... | | ..... | +---------------------------------------------------------------+ o Type: sub-TLV Type = 8 (Pending IANA). o Length: The size of the value is ECT-VID Tuples*6 bytes. Each 6- byte part of the ECT-VID tuple is formatted as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ECT - Algorithm (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Base VID (12 bits) |U|M|RES| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o ECT-ALGORITHM (4 bytes) The ECT-ALGORITHM is advertised when the bridge supports a given ECT-ALGORITHM (by OUI/Index) on a given Base-VID. There are 17 predefined IEEE algorithms for SPB with index values 0X00..0X10 occupying the low 8 bits and the IEEE OUI=00-80-C2 occupying the top 24 bits of the ECT-ALGORITHM. o Base-VID (12-bits) The Base-VID that is associated with the SPT Set. o Use-Flag (1-bit) The Use-flag is set if this bridge, or any bridge in the LSDB is currently using this ECT-ALGORITHM and Base-VID. Remote usage is discovered by inspection of the U-Bit in the SPB Instance sub-TLV of other SPB bridges (see section 14.1) Fedyk, et al. Expires August, 2011 [Page 24] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o M-Bit (1-bit) The M-bit indicates if this Base-VID operates in SPBM (M = 1) or SPBV (M = 0) mode. The SPB Base VLAN-Identifier sub-TLV is carried within the MT-Port- Cap TLV [LAYER2] which in turn is carried in an IIH PDU. 14. Node information extensions All SPB nodal information extensions travel within a new multi topology capability TLV MT-Capability (type = 144). 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type = MT-CAP | = 144 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |O R R R| MT ID | (2 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ (sub-TLVs ... ) The format of this TLV is identical in its first 2 bytes to all current MT TLV's and carries the MT ID as defined in [MT]. The O (overload) bit carried in bit 16 has the same semantics as specified in [MT], but in the context of SPB adjacencies only. 14.1. SPB Instance sub-TLV The SPB Instance sub-TLV gives the SPSourceID for this node/topology instance. This is the 20 bit value that is used in the formation of multicast DA addresses for frames originating from this node/instance. The SPSourceID occupies the upper 20 bits of the multicast DA together with 4 other bits (see the SPBM 802.1ah multicast DA address format section). This sub-TLV MUST be carried within the MT-Capability TLV in the fragment ZERO LSP. If there is an additional SPB instance it must be declared under a separate MT- Topology and also carried in the fragment ZERO LSP. Fedyk, et al. Expires August, 2011 [Page 25] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type = SPB-Inst| = 1 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CIST Root Identifier (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CIST Root Identifier (cont) (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CIST External ROOT Path Cost (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bridge Priority | (2 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |R R R R R R R R R R R|V| SPSourceID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Num of Trees | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | VLAN-ID (1) Tuples (8 bytes) | | ........................... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ........................... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | VLAN-ID (N) Tuples (8 bytes) | | ........................... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ where VLAN-ID tuples have the format as: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |U|M|A| Res | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ECT - Algorithm (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Base-VID (12 bits) | SPVID (12 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type 1 (Pending IANA). o Length: Total number of bytes contained in the value field. Fedyk, et al. Expires August, 2011 [Page 26] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o CIST Root Identifier (64-bits)The CIST Root Identifier is for SPB interworking with RSTP and MSTP at SPT Region Boundaries. This is an imported value from a Spanning tree. o CIST External Root Path Cost (32-bits) The CIST External Root Path Cost is the cost to root, derived from the spanning tree algorithm. o Bridge Priority (16-bits) Bridge priority is the 16 bits that together with the 6 bytes of the System ID form the Bridge Identifier. This is configured exactly as specified in IEEE802 [802.1D]. This allows SPB to build a compatible Spanning tree using link state by combining the Bridge Priority and the System ID to form the 8 byte Bridge Identifier. The 8 byte Bridge Identifier is also the input to the 16 pre-defined ECT tie breaker algorithms. o V bit (1-Bit) The V bit (SPBM) indicates this SPSourceID is auto allocated(27.11). If the V bit is clear the SPSourceID has been configured and must be unique. Allocation of SPSourceID is defined in IEEE [802.1aq]. Bridges running SPBM will allocate an SPSourceID if they are not configured with an explicit SPSourceID. The V Bit allows neighbor bridges to determine if the auto allocation was enabled. In the rare chance of a collision of SPsourceID allocation, the bridge with the highest priority Bridge Identifier will win conflicts and the lower priority Bridge will be re-allocated or if the lower priority Bridge is configured it will not be allowed to join the SPT Region. o The SPSourceID is a 20 bit value used to construct multicast DA's as described below for multicast frames originating from the origin (SPB node) of the link state packet (LSP) that contains this TLV. More details are in IEEE [802.1aq]. o Number of Trees (8-bits) The Number of Trees is set to the number of [ECT-ALGORITHM, Base-VID plus flags] tuples that follow. Each ECT-ALGORITHM has a Base-VID, an SPVID and flags described below. This must contain at least the one ECT-ALGORITMM (00-80-C2-01). Each VID Tuple consists of: o U-Bit (1-bit) The U-bit is set if this bridge is currently using this ECT-ALGORITHM for I-SIDs it sources or sinks. This is a strictly local indication; the semantics differ from the Use-flag found in the Hello, which will set the Use-Flag if it sees other nodal U-bits are set OR it sources or sinks itself. Fedyk, et al. Expires August, 2011 [Page 27] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o M-Bit (1-bit) The M-bit indicates if this is SPBM or SPBV mode. When cleared the mode is SPBV and when set the mode is SPBM. o A bit, The A bit (SPB) when set declares this is an SPVID with auto allocation. The VID allocation logic details are in IEEE [802.1aq]. Since SPVIDs are allocated from a small pool of 12 bit resources the chances of collision are high. To minimize collisions during auto allocation LSPs are initially advertised with the originating bridge setting the SPVID to 0. Only after learning the other bridges' SPVID allocations does this bridge re-advertise this sub-TLV with a non-zero SPVID. This will minimize but not eliminate the chance of a clash. In the event of a clash, the highest Bridge Identifier is used to select the winner, while the loser(s) with lower Bridge Identifier(s) must withdraw their SPVID allocation(s), and select an alternative candidate for another trial. SPVID may also be configured. When the A bit is set to not specify auto allocation and the SPVID is set to 0 this SPBV bridge is used for transit only within the SPB region. If a port is configured with the BASE-VID as a neighbor using RSTP or MSTP the bridge will act as an ingress filter for that VID. o ECT-ALGORITHM (4-bytes) ECT-ALGORITHM is advertised when the bridge supports a given ECT-ALGORITHM (by OUI/Index) on a given VID. This declaration must match the declaration in the Hello PDU originating from the same bridge. The ECT-ALGORITHM and BASE-VID must match what is generated in the IIHs of the same node. The ECT-ALGORITHM, BASE-VID tuples can come in any order however. There are currently 17 world wide unique 802.1aq defined ECT- ALGORITHMS given by values 00-80-C2-00 through 00-80-C2-10. o Base VID (12-bits) The Base-VID that associated the SPT Set via the ECT-ALGORITHM. o SPVID (12-bits) The SPVID is the Shortest Path VID assigned for the Base-VID to this node when using SPBV mode. It is not defined for SPBM Mode and must be 0 for SPBM mode B-VIDs. 14.1.1. SPB Instance Opaque ECT-ALGORITHM sub-TLV There are multiple ECT algorithms defined for SPB, however for the future additional algorithms may be defined including but not limited to ECMP / hash based behaviors and (*,G) multicast trees. These algorithms will use this optional TLV to define new algorithm parametric data. For tie breaking parameters there are two broad classes of algorithm, one which uses nodal data to break ties and one which uses link data to break ties, this TLV is used to Fedyk, et al. Expires August, 2011 [Page 28] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 associate opaque tie breaking data with a node. This sub-TLV, when present, MUST be carried within the MT-Capability TLV (along with a valid SPB Instance sub-TLV). Multiple copies of this sub-TLV MAY be carried for different ECT-ALGORITHMs relating to this node. There are of course many other uses of this opaque data which have yet to be defined. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type=SPB-I-OALG| = 2 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opaque ECT Algorithm (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opaque ECT Information (variable) | | ....................... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type 2 (Pending IANA). o Length: Total number of bytes contained in the value field. o ECT-ALGORITHM: ECT-ALGORITHM is advertised when the bridge supports a given ECT-ALGORITHM (by OUI/Index) on a given VID. o ECT Information: ECT-ALGORITHM Information of variable length which SHOULD be in sub-TLV format with an IANA numbering space where appropriate. 15. Adjacency information extensions 15.1. SPB Link Metric sub-TLV The SPB Link Metric sub-TLV (type = 12) occurs within the Multi Topology Intermediate System TLV (type 222) or within the Extended IS Reachability TLV (type 22). If this sub TLV is not present for an ISIS adjacency then that adjacency must not carry SPB traffic for the given topology instance. Fedyk, et al. Expires August, 2011 [Page 29] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type=SPB-Metric| = 12 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SPB-LINK-METRIC | (3 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Num of ports | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port Identifier | ( 2 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type 12 (Pending IANA). o Length: Total number of bytes contained in the value field. o SPB-LINK-METRIC indicates the administrative cost or weight of using this link as a 24 bit unsigned number. This metric applies to the use of this link for SPB traffic only. Smaller numbers indicate lower weights and are more likely to carry SPB traffic. Only one metric is allowed per SPB instance per link. If multiple metrics are required multiple SPB instances are required, either within IS-IS or within several independent IS-IS instances. If this metric is different at each end of a link, the maximum of the two values must be used in all SPB calculations for the weight of this link. The maximum SPB-LINK-METRIC value 2^24 - 1 has a special significance; this value indicates that although the IS-IS adjacency has formed, incompatible values have been detected in parameters configured within SPB itself for example different regions, and the link must not be used for carrying SPB traffic. Full details are found in [802.1aq]. o Num of Ports is the number of ports associated with this link. o Port Identifier is the standard IEEE port identifier used to build a spanning tree associated with this link. 15.1.1. SPB Adjacency Opaque ECT-ALGORITHM sub-TLV There are multiple ECT algorithms defined for SPB, however for the future additional algorithms may be defined. The SPB Adjacency Opaque ECT-ALGORITHM sub-TLV occurs within the Multi Topology Intermediate System TLV (type 222) or the Extended IS Reachability Fedyk, et al. Expires August, 2011 [Page 30] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 TLV (type 22). Multiple copies of this sub-TLV MAY be carried for different ECT-ALGORITHMs related to this adjacency. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type=SPB-A-OALG| = 13 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opaque ECT Algorithm (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opaque ECT Information (variable) | | ......................... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type = 13 (PENDING IANA). o Length: Total number of bytes contained in the value field. o ECT-ALGORITHM: ECT-ALGORITHM is advertised when the bridge supports a given ECT-ALGORITHM (by OUI/Index) on a given VID. o ECT Information: ECT-ALGORITHM Information of variable length in sub-TLV format using new IANA type values as appropriate. 16. Service information extensions 16.1. SPBM Service Identifier and Unicast Address sub-TLV The SPBM Service Identifier and Unicast Address sub-TLV (type=3) is used to introduce service group membership on the originating node and/or to advertise an additional B-MAC unicast address present on, or reachable by the node. Fedyk, et al. Expires August, 2011 [Page 31] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ |Type = SPBM-SI | = 3 +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | B-MAC ADDRESS | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | B-MAC ADDRESS (6 bytes) | Res. | Base-VID (12 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |T|R| Reserved | ISID #1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |T|R| Reserved | ISID #2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ................. +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |T|R| Reserved | ISID #n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type = 3 (Pending IANA) o Length: Total number of bytes contained in the value field. o B-MAC ADDRESS is a unicast address of this node. It may be either the single nodal address, or may address a port or any other level of granularity relative to the node. In the case where the node only has one B-MAC address this should be the same as the SYS-ID of the node. To add multiple B-MACs this TLV MUST be repeated per additional B-MAC. o Base VID (12-bits) The Base-VID associated with the B-BMAC this allows the linkage to the ECT-Algorithm and SPT Set defined in the SPB Instance sub-TLV. Fedyk, et al. Expires August, 2011 [Page 32] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o ISID #1 .. #N are 24 bit service group membership identifiers. If two nodes have an I-SID in common, intermediate nodes on the unique shortest path between them will create forwarding state for the related B-MAC addresses and will also construct multicast forwarding state using the I-SID and the node's SPSourceID to construct a multicast DA as described in IEEE 802.1aq LSB. Each I-SID has a Transmit(T) and Receive(R) bit which indicates if the membership is as a Transmitter/Receiver or both (with both bits set). In the case where the Transmit(T) and Receive(R) bits are both zero, the I-SID instance is ignored for the purposes of distributed multicast computation, but the unicast B-MAC address must be processed and installed at nodes providing transit to that address. If more I-SIDs are associated with a particular B- MAC than can fit in a single sub-TLV, this sub-TLV can be repeated with the same B-MAC but with different I-SID values. o Note when the T bit is not set an SPB may still multicast to all the other receive members of this I-SID (those advertising with their R bits set), by configuring edge replication and serial unicast to each member locally. The SPBM Service Identifier sub-TLV, when present, MUST be carried within the MT Capability TLV and can occur multiple times in any LSP fragment. 16.2. SPBV Mac Address sub-TLV The SPBV MAC Address (SPBV-MAC-ADDR) sub-TLV is IS-IS sub-TLV type 4 (PENDING IANA). It should be used for advertisement of Group MAC Addresses in SPBV mode. Unicast MAC addresses will normally be distributed by reverse path learning, but carrying them in this TLV is not precluded. It has the following format : Fedyk, et al. Expires August, 2011 [Page 33] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+ | Type=SPBV-ADDR| = 4 (1 byte) +-+-+-+-+-+-+-+-+ | Length | (1 byte) +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |R|R|S-R| SPVID | (2 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+ |T|R| Reserved | MAC 1 Address | (1+6 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+ ... +-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+ |T|R| Reserved | MAC N Address | (1+6 bytes) +-+-+-+-+-+-+-+-+-+-+-+-+...+-+-+-+-+-+-+-+-+-+-+-+ o Type: sub-TLV Type, set to 4. o Length: Total number of bytes contained in the value field. The number of MAC address associated with the SPVID is computed by (Length - 2)/7. o S-R bits (2-bits) The SR bits are the service requirement parameter from MMRP. The service requirement parameters have the value 0 (Forward all Groups) and 1 (Forward All Unregistered Groups) defined. However this attribute may also be missing. So the SR bits are defined as 0 not declared, 1 Forward all Groups and 2 Forward All Unregistered Groups. The two 'R' reserved bits immediately preceding these SR bits should be set to zero when originating this sub-TLV and ignored on receipt. o SPVID (12-bits) The SPVID and by association Base-VID and the ECT-ALGORITHM and SPT Set that the MAC addresses defined below will use. If the SPVID is not allocated the SPVID Value is 0. Note that if the ECT-Algorithm in use is Spanning Tree Algorithm this value must be populated with the Base-VID and the MAC must be populated. Fedyk, et al. Expires August, 2011 [Page 34] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 o T Bit (1-bit) This is the Transmit allowed Bit for a following group MAC address. This is an indication that the Group MAC Address in the context of the SPVID of the bridge advertising this Group MAC must be installed in the FDB of transit bridges, when the bridge computing the trees is on the corresponding ECT- ALGORITHM shortest path between the bridge advertising this MAC with the T bit set and any receiver of this Group MAC Address. A bridge that does not advertise this bit set for a MAC Address must not cause multicast forwarding state to be installed on other transit bridges in the network for traffic originating from that bridge. o R Bit (1-bit) This is the Receive allowed Bit for the following MAC Address. This is an indication that MAC Addresses as receiver must be populated and installed when the bridge computing the trees lies on the corresponding shortest path for this ECT- ALGORITHM between this receiver and any transmitter to this MAC Address. An entry that does not have this bit set for a Group MAC Address is prevented from receiving on this Group MAC Address because transit bridges must not install multicast forwarding state towards it in their FDBs, or the traffic must be explicitly filtered. o MAC Address (48-bits) The MAC address declares this bridge as part of the multicast interest for this destination MAC address. Multicast trees can be efficiently constructed for destination by populating FDB entries for the subset of the shortest path tree that connects the bridges supporting the MAC address. This replaces the function of MMRP for SPTs. The T and R bits above have meaning as specified above. The SPBV-MAC-ADDR sub-TLV, when present, MUST be carried within the MT-Capability TLV and can occur multiple times in any LSP fragment. 17. Security Considerations This document adds no additional security risks to IS-IS, nor does it provide any additional security for IS-IS when used in a configured environment or a single operator domain such as a Data Center. However this protocol may be used in a zero configuration environment. Zero configuration may apply to the automatic detection and formation of an IS-IS adjacency (forming an NNI port). Likewise zero configuration may apply to the automatic detection of VLAN tagged traffic and the formation of a UNI port, with resultant ISID advertisements. Fedyk, et al. Expires August, 2011 [Page 35] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 If zero configuration methods are used to auto configure NNIs or UNIs there are intrinsic security concerns that should be mitigated with authentication procedures for the above cases. Such procedures are beyond the scope of this document. In addition, this protocol can create significant amounts of multicast state when an ISID is advertised with the TX bit set. Extra care should be taken to ensure that this cannot be used as a DOS attack in a zero configuration environment. 18. IANA Considerations Note that the NLPID value 0xC1 [NLPID] used in the IIH PDUs has already been assigned by IANA for the purpose of 802.1aq therefore no further action is required for this code point. Since 802.1aq operates within the IS-IS Multi Topology framework every sub-TLV MUST occur in the context of the proper MT TLV (with the exception of the SPB Link Metric sub-TLV which MAY travel in TLV 22 where its MT-ID is unspecified but implied to be 0). There are three Multi Topology TLV's in which 802.1aq requests allocation of sub-TLV's. These are the MT-Port-Cap TLV [LAYER2] used in the IIH, the MT-Capability TLV (new) used within the LSP and finally the MT- Intermediate-System TLV [MT] used to contain adjacency information within the LSP. This document creates the following TLVs & sub-TLV's within the IIH and LSP PDUs MT TLV's as described below. The '*' indicates IANA action is required. Other entries are shown to provide context only. A '?' next to a number indicates a requested but of course not necessarily the final assigned value. The MT-Capability TLV is the only TLV requiring a new sub-registry. Type value 144 (TBD) is requested, with a starting sub-TLV value of 1, and managed by Standards Action. Fedyk, et al. Expires August, 2011 [Page 36] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 +-----+----+-----------------+--------+------+-------------+ | PDU |TLV | SUB-TLV | TYPE | TYPE | #OCCURRENCE | +-----+----+-----------------+--------+------+-------------+ IIH MT-Port-Cap 147? * SPB-MCID 6? 1 * SPB-Digest 7? >=0 * SPB-B-VID 8? 1 LSP * MT-Capability 144? * SPB-Inst 1? 1 * SPB-I-OALG 2? >=0 * SPBM-SI 3? >=0 * SPBV-ADDR 4? >=0 MT-Intermediate-System 222 or Extended IS Reachability 22 * SPB-Metric 12? 1 * SPB-A-OALG 13? >=0 19. References 19.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [IS-IS] ISO/IEC 10589:2002, Second Edition, "Intermediate System to Intermediate System Intra-Domain Routing Exchange Protocol for use in Conjunction with the Protocol for Providing the Connectionless-mode Network Service (ISO 8473)", 2002. [MT] M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs), RFC 5120, February 2008. [802.1aq] "Standard for Local and Metropolitan Area Networks / Virtual Bridged Local Area Networks / Amendment: Shortest Path Bridging, Draft IEEE P802.6aq/3.2", 2010. [NLPID] www.ietf.org/id/draft-eastlake-nlpid-iana-considerations- 04.txt Fedyk, et al. Expires August, 2011 [Page 37] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 [LAYER2] www.ietf.org/id/draft-ietf-isis-layer2-09.txt. 19.2. Informative References [MMRP] "Standard for Local and Metropolitan Area Networks Virtual Bridged Local Area Networks - Amendment 07: Multiple Registration Protocol", IEEE STD 802.1ak, 2007 [PB] "Standard for Local and Metropolitan Area Networks / Virtual Bridged Local Area Networks / Amendment 4: Provider Bridges, IEEE STD 802.1ad", 2005. [PBB] "Standard for Local and Metropolitan Area Networks / Virtual Bridged Local Area Networks / Amendment 7: Provider Backbone Bridges, IEEE STD 802.1ah", 2008. [802.1ag] "Standard for Local and Metropolitan Area Networks / Virtual Bridged Local Area Networks / Amendment 5: Connectivity Fault Management", IEEE STD 802.1ag, 2007 [Y.1731] ITU-T Y.1731 (2006), "OAM Functions and Mechanisms for Ethernet based networks" 20. Acknowledgments The authors would like to thank Ayan Banerjee, Mick Seaman, Janos Farkas, Les Ginsberg, Stewart Bryant , Donald Eastlake, Matthew Bocci and Mike Shand for contributions and/or detailed review. This document was prepared using 2-Word-v2.0.template.dot. 21. Author's Addresses Don Fedyk Alcatel-Lucent Groton, MA, 01450, USA Email: Donald.Fedyk@alcatel-lucent.com Peter Ashwood-Smith Huawei Technologies Canada Ltd, 303 Terry Fox Drive, Suite 400 Kanata, Ontario, K2K 3J1, CANADA Email: Peter.AshwoodSmith@huawei.com Fedyk, et al. Expires August, 2011 [Page 38] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 Dave Allan Ericsson, 300 Holger Way San Jose, CA 95134 Email: david.i.allan@ericsson.com Nigel Bragg Ciena Limited, Ciena House 43-51 Worship Street London EC2A 2DX Email: nbragg@ciena.com Paul Unbehagen Alcatel-Lucent 8742 Lucent Boulevard Highlands Ranch, CO 80129, USA Email: Paul.Unbehagen@alcatel-lucent.com 22. Intellectual Property Statement The IETF Trust takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in any IETF Document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Copies of Intellectual Property disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement any standard or specification contained in an IETF Document. Please address the information to the IETF at ietf-ipr@ietf.org. Fedyk, et al. Expires August, 2011 [Page 39] Internet-Draft draft-ietf-isis-ieee-aq-04.txt February 2011 23. Disclaimer of Liability This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT not LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL not INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS. Fedyk, et al. Expires August, 2011 [Page 40]