Network Working Group M. Bagnulo
Internet-Draft UC3M
Intended status: Informational T. Burbridge
Expires: December 21, 2014 BT
S. Crawford
SamKnows
P. Eardley
BT
A. Morton
AT&T Labs
June 19, 2014

A Reference Path and Measurement Points for LMAP
draft-ietf-ippm-lmap-path-04

Abstract

This document defines a reference path for Large-scale Measurement of Broadband Access Performance (LMAP) and measurement points for commonly used performance metrics. The methods for measurement point location may be applicable to similar measurement projects using the extensions described here.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on December 21, 2014.

Copyright Notice

Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This document defines a reference path for Large-scale Measurement of Broadband Access Performance (LMAP) or similar measurement projects. The series of IP Performance Metrics (IPPM) RFCs have developed terms that are generally useful for path description (section 5 of [RFC2330]). There are a limited number of additional terms needing definition here, and they will be defined in this memo.

The reference path is usually needed when attempting to communicate precisely about the components that comprise the path, often in terms of their number (hops) and geographic location. This memo takes the path definition further, by establishing a set of measurement points along the path and ascribing a unique designation to each point. This topic has been previously developed in section 5.1 of [RFC3432], and as part of the updated framework for composition and aggregation, section 4 of [RFC5835] (which may also figure in the LMAP work effort). Section 4.1 of [RFC5835] defines the term "measurement point".

Measurement points and the paths they cover are often described in general terms, like "end-to-end", "user-to-user", or "access". These terms alone are insufficient for scientific method: What is an end? Where is a user located? Is the home network included?

The motivation for this memo is to provide an unambiguous framework to describe measurement coverage, or scope of the reference path. This is an essential part of the meta-data to describe measurement results. Measurements conducted over different path scopes are not a valid basis for performance comparisons. We note that additional measurement context information may be necessary to support a valid comparison of results.

1.1. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].

2. Purpose and Scope

The scope of this memo is to define a reference path for LMAP activities with sufficient level of detail to determine the location of different measurement points along a path without ambiguity. These conventions are likely to be useful in other measurement projects as well.

The connection between the reference path and specific network technologies (with differing underlying architectures) is within the scope of this method, and examples are provided. Both wired and wireless technologies are in-scope.

The purpose is to create an efficient way to describe the location of the measurement point(s) used to conduct a particular measurement so that the measurement result will adequately described in terms of scope or coverage. This should serve many measurement uses, including:

diagnostic:
where the same metric may be measured over many different path scopes
comparison:
where the same metric may be measured on equivalent portions of different network infrastructures

3. Terms and Definitions

This section defines key terms and concepts for the purposes of this memo.

3.1. Reference Path

A reference path is a serial combination of routers, switches, links, radios, and processing elements that comprise all the network elements traversed by each packet between the source and destination hosts. The reference path is intended to be equally applicable to all networking technologies, therefore the components are generically defined, but their functions should have a clear counterpart or be obviously omitted in any network technology.

3.2. Subscriber

An entity (associated with one or more users) that is engaged in a subscription with a service provider. The subscriber is allowed to subscribe and un-subscribe services, and to register a user or a list of users authorized to enjoy these services. [Q1741] Both the subscriber and service provider are allowed to set the limits relative to the use that associated users make of subscribed services.

3.3. Dedicated Component (Links or Nodes)

All resources of a Dedicated component (typically a link or node on the Reference Path) are allocated to serving the traffic of an individual Subscriber. Resources include transmission time-slots, queue space, processing for encapsulation and address/port translation, and others. A Dedicated component can affect the performance of the Reference Path, or the performance of any sub-path where the component is involved.

3.4. Shared Component (Links or Nodes)

A component on the Reference Path is designated a Shared component when the traffic associated with multiple Subscribers is served by common resources.

3.5. Resource Transition Point

A point between Dedicated and Shared components on a Reference Path that may be a point of significance, and is identified as a transition between two types of resources.

3.6. Managed and Un-Managed Sub-paths

Service providers are responsible for the portion of the path they manage. However, most paths involve a sub-path which is beyond the management of the subscriber's service provider. This means that private networks, wireless networks using unlicensed frequencies, and the networks of other service are designated as un-managed sub-paths. The Service demarcation point always divides managed and un-managed sub-paths.

4. Reference Path

This section defines a reference path for Internet communication.

Subsc. -- Private -- Private -- Service-- Intra IP -- GRA -- Transit
device     Net #1     Net #2    Demarc.    Access     GW     GRA GW


... Transit -- GRA -- Service -- Private -- Private -- Destination 
    GRA GW     GW     Demarc.    Net #n     Net #n+1   Host

GRA = Globally Routable Address, GW = Gateway

The following are descriptions of reference path components that may not be clear from their name alone.

Use of multiple IP address families in the measurement path must be noted, as the conversions between IPv4 and IPv6 certainly influence the visibility of a GRA for each family.

In the case that a private address space is used throughout an access architecture, then the Service Demarc. and the Intra IP Access points must use the same address space and be separated by the shared and dedicated access link infrastructure, such that a test between these points produces a useful assessment of access performance.

5. Measurement Points

A key aspect of measurement points, beyond the definition in section 4.1 of [RFC5835], is that the innermost IP header and higher layer information must be accessible through some means. This is essential to measure IP metrics. There may be tunnels and/or other layers which encapsulate the innermost IP header, even adding another IP header of their own.

In general, measurement points cannot always be located exactly where desired. However, the definition in [RFC5835] and the discussion in section 5.1 of [RFC3432] indicate that allowances can be made: for example, it is nearly ideal when there are deterministic errors that can be quantified between desired and actual measurement point.

The Figure below illustrates the assignment of measurement points to selected components of the reference path.

Subsc. -- Private -- Private -- Service-- Intra IP -- GRA -- Transit
device     Net #1     Net #2    Demarc.    Access     GW     GRA GW
mp000                            mp100      mp150    mp190    mp200


... Transit -- GRA -- Service -- Private -- Private -- Destination 
    GRA GW     GW     Demarc.    Net #n     Net #n+1   Host
    mpX90     mp890   mp800                            mp900     

GRA = Globally Routable Address, GW = Gateway

Figure 1

When communicating the results of measurements using the measurement point designations described here, the measuring organization SHOULD supply a diagram similar to Figure 1 (and the technology-specific examples that follow), and MUST supply it when additional measurement point numbers have been defined and used, with sufficient detail to identify measurement locations in the path. Organizations with similar technologies and architectures are encouraged to coordinate on local numbering and diagrams, when possible.

The measurement point numbering system, mpXnn, has two independent parts:

  1. The X in mpXnn indicates the network number. The network with the Subscriber's device is network 0. The network of a different organization (administrative or ownership domains) SHOULD be assigned a different number. Each successive network number SHOULD be one greater than the previous network's number. Two circumstances make it necessary to designate X=9 in the Destination Host's network and X=8 for the Service Provider network at the Destination:
    1. The number of Transit networks is unknown.
    2. The number of Transit networks varies over time.
  2. The nn in mpXnn indicates the measurement point and is locally-assigned by network X. The following conventions are suggested:
    1. 00 SHOULD be used for a measurement point at the Subscriber's device and at the Service Demarcation point or GW nearest to the Subscriber's device for Transit Networks.
    2. 90 SHOULD be used for a measurement point at the GW of a network (opposite from the Subscriber's device or Service Demarc.).
    3. In most networks, measurement point numbers SHOULD monotonically increase from point nearest the Subscriber's device to the opposite network boundary on the path (see below).
    4. When a Detination host is part of the path, 00 SHOULD be used for a measurement point at the Destination host and at the the Destination's Service Demarcation point. Measurement point numbers SHOULD monotonically increase from point nearest the Destination's host to the opposite network boundary on the path ONLY in these networks. This directional numbering reversal allows consistent 00 designation for end hosts and Service Demarcs.
    5. 50 MAY be used for an intermediate measurement point of significance, such as a Network Address Translator (NAT).
    6. 20 MAY be used for a traffic aggregation point such as a DSLAM within a network.
    7. Any other measurement points SHOULD be assigned unused integers between 01 and 99. The assignment SHOULD be stable for at least the duration of a particular measurement study, and SHOULD avoid numbers that have been assigned to other locations within network X (unless the assignment is considered sufficiently stale). Sub-networks or domains within a network are useful locations for measurement points.

In order to define the measurement points and the scope of measurements without ambiguity, the operator of the measurement system SHOULD indicate on a diagram (similar to those in this document): the reference path, the numbers (mpXnn) of the measurement points, and the definition of any measurement point other than 00 and 90 (with sufficient detail to clearly define its location).

If the number of intermediate networks (between the source and destination) is not known or is unstable, then this SHOULD be indicated on the diagram and results from measurement points within those networks need to be treated with caution.

Notes:

6. Translation Between Reference Path and Various Technologies

This section and those that follow are intended to provide a more exact mapping between particular network technologies and the reference path.

We provide an example for 3G Cellular access below.

Subscriber -- Private ---  Service ------------- GRA --- Transit ... 
device         Net #1      Demarc.                GW     GRA GW
mp000                       mp100                mp190    mp200

|_____________UE______________|___RAN+Core____|___GGSN__|
|_____Un-managed sub-path_____|____Managed sub-path_____|  

GRA = Globally Routable Address, GW = Gateway, UE = User Equipment, RAN = Radio Access Network, GGSN = Gateway GPRS Support Node.

We next provide an example of DSL access. Consider the case where:

We believe this is a fairly common configuration in some parts of the world and fairly simple as well.

This case would map into the defined reference measurement points as follows:

Subsc. -- Private -- Private -- Service-- Intra IP -- GRA -- Transit
device     Net #1     Net #2    Demarc.    Access     GW     GRA GW
mp000                            mp100      mp150    mp190    mp200
|--UE--|------------CPE/NAT--------|------|-BRAS-|------|
                                   |------DSL Network---|
|_______Un-managed sub-path________|__Managed sub-path__|
			

GRA = Globally Routable Address, GW = Gateway, BRAS = Broadband Remote Acess Server

Consider next another access network case where:

We believe this is becoming a fairly common configuration in some parts of the world.

This case would map into the defined reference measurement points as follows:

Subsc. -- Private ------------- Service-- Intra IP -- GRA -- Transit
device     Net #1               Demarc.    Access     GW     GRA GW
mp000                            mp100      mp150    mp190    mp200
|--UE--|------------CPE/NAT--------|------|-CGN-|------|
                                   |--Access Network---| 
|_______Un-managed sub-path________|_Managed sub-path__|                  
			

GRA = Globally Routable Address, GW = Gateway

7. Example Resource Transition

This section gives an example of Shared and Dedicated portions with the reference path. This example shows two Resource Transition Points.

Consider the case where:

We believe this is a fairly common configuration in parts of the world.

This case would map into the defined reference measurement points as follows:

Subsc. -- Private -- Private -- Access -- Intra IP -- GRA -- Transit
device     Net #1     Net #2    Demarc.    Access     GW     GRA GW
mp000                            mp100      mp150    mp190    mp200
|--UE--|------------CPE/NAT--------|------|-CGN-|------|
       |   Wi-Fi  |  1000Base-T    |--Access Network---| 
                  
       |-Shared--|RT|------Dedicated------| RT  |-----Shared------...
|_______Un-managed sub-path________|_Managed sub-path__|

GRA = Globally Routable Address, GW = Gateway, RT = Resource Transition Point

8. Security considerations

Specification of a Reference Path and identification of measurement points on the path represent agreements among interested parties, and they present no threat to the readers of this memo or to the Internet itself.

When considering privacy of those involved in measurement or those whose traffic is measured, there is sensitive information communicated to recipients of the network diagrams illustrating paths and measurement points described above. We refer the reader to the privacy considerations described in the Large Scale Measurement of Broadband Performance (LMAP) Framework [I-D.ietf-lmap-framework], which covers active and passive measurement techniques and supporting material on measurement context.

9. IANA Considerations

This memo makes no requests for IANA consideration.

10. Acknowledgements

Thanks to Matt Mathis, Charles Cook, Dan Romascanu, and Lingli Deng for review and comments.

11. References

11.1. Normative References

[RFC2330] Paxson, V., Almes, G., Mahdavi, J. and M. Mathis, "Framework for IP Performance Metrics", RFC 2330, May 1998.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3432] Raisanen, V., Grotefeld, G. and A. Morton, "Network performance measurement with periodic streams", RFC 3432, November 2002.
[RFC5835] Morton, A. and S. Van den Berghe, "Framework for Metric Composition", RFC 5835, April 2010.

11.2. Informative References

[I-D.ietf-lmap-framework] Eardley, P., Morton, A., Bagnulo, M., Burbridge, T., Aitken, P. and A. Akhter, "A framework for large-scale measurement platforms (LMAP)", Internet-Draft draft-ietf-lmap-framework-06, June 2014.
[SK] Crawford, Sam., "Test Methodology White Paper", SamKnows Whitebox Briefing Note http://www.samknows.com/broadband/index.php, July 2011.
[Q1741] Q.1741.7, , "IMT-2000 references to Release 9 of GSM-evolved UMTS core network", http://www.itu.int/rec/T-REC-Q.1741.7/en, November 2011.

Authors' Addresses

Marcelo Bagnulo Universidad Carlos III de Madrid Av. Universidad 30 Leganes, Madrid 28911 SPAIN Phone: 34 91 6249500 EMail: marcelo@it.uc3m.es URI: http://www.it.uc3m.es
Trevor Burbridge BT Adastral Park, Martlesham Heath Ipswich, ENGLAND EMail: trevor.burbridge@bt.com
Sam Crawford SamKnows EMail: sam@samknows.com
Phil Eardley BT Adastral Park, Martlesham Heath Ipswich, ENGLAND EMail: philip.eardley@bt.com
Al Morton AT&T Labs 200 Laurel Avenue South Middletown, NJ, USA EMail: acmorton@att.com