ippm F. Brockners
Internet-Draft S. Bhandari
Intended status: Standards Track C. Pignataro
Expires: September 11, 2019 Cisco
H. Gredler
RtBrick Inc.
J. Leddy
Comcast
S. Youell
JPMC
T. Mizrahi
Huawei Network.IO Innovation Lab
D. Mozes
P. Lapukhov
Facebook
R. Chang
Barefoot Networks
D. Bernier
Bell Canada
J. Lemon
Broadcom
March 10, 2019

Data Fields for In-situ OAM
draft-ietf-ippm-ioam-data-05

Abstract

In-situ Operations, Administration, and Maintenance (IOAM) records operational and telemetry information in the packet while the packet traverses a path between two points in the network. This document discusses the data fields and associated data types for in-situ OAM. In-situ OAM data fields can be embedded into a variety of transports such as NSH, Segment Routing, Geneve, native IPv6 (via extension header), or IPv4. In-situ OAM can be used to complement OAM mechanisms based on e.g. ICMP or other types of probe packets.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on September 11, 2019.

Copyright Notice

Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This document defines data fields for "in-situ" Operations, Administration, and Maintenance (IOAM). In-situ OAM records OAM information within the packet while the packet traverses a particular network domain. The term "in-situ" refers to the fact that the OAM data is added to the data packets rather than is being sent within packets specifically dedicated to OAM. IOAM is to complement mechanisms such as Ping or Traceroute, or more recent active probing mechanisms as described in [I-D.lapukhov-dataplane-probe]. In terms of "active" or "passive" OAM, "in-situ" OAM can be considered a hybrid OAM type. While no extra packets are sent, IOAM adds information to the packets therefore cannot be considered passive. In terms of the classification given in [RFC7799] IOAM could be portrayed as Hybrid Type 1. "In-situ" mechanisms do not require extra packets to be sent and hence don't change the packet traffic mix within the network. IOAM mechanisms can be leveraged where mechanisms using e.g. ICMP do not apply or do not offer the desired results, such as proving that a certain traffic flow takes a pre-defined path, SLA verification for the live data traffic, detailed statistics on traffic distribution paths in networks that distribute traffic across multiple paths, or scenarios in which probe traffic is potentially handled differently from regular data traffic by the network devices.

2. Conventions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].

Abbreviations used in this document:

E2E
Edge to Edge
Geneve:
Generic Network Virtualization Encapsulation [I-D.ietf-nvo3-geneve]
IOAM:
In-situ Operations, Administration, and Maintenance
MTU:
Maximum Transmit Unit
NSH:
Network Service Header [RFC8300]
OAM:
Operations, Administration, and Maintenance
POT:
Proof of Transit
SFC:
Service Function Chain
SID:
Segment Identifier
SR:
Segment Routing
VXLAN-GPE:
Virtual eXtensible Local Area Network, Generic Protocol Extension [I-D.ietf-nvo3-vxlan-gpe]

3. Scope, Applicability, and Assumptions

IOAM deployment assumes a set of constraints, requirements, and guiding principles which are described in this section.

Scope: This document defines the data fields and associated data types for in-situ OAM. The in-situ OAM data field can be transported by a variety of transport protocols, including NSH, Segment Routing, Geneve, IPv6, or IPv4. Specification details for these different transport protocols are outside the scope of this document.

Deployment domain (or scope) of in-situ OAM deployment: IOAM is a network domain focused feature, with "network domain" being a set of network devices or entities within a single administration. For example, a network domain can include an enterprise campus using physical connections between devices or an overlay network using virtual connections / tunnels for connectivity between said devices. A network domain is defined by its perimeter or edge. Designers of carrier protocols for IOAM must specify mechanisms to ensure that IOAM data stays within an IOAM domain. In addition, the operator of such a domain is expected to put provisions in place to ensure that IOAM data does not leak beyond the edge of an IOAM domain, e.g. using for example packet filtering methods. The operator should consider potential operational impact of IOAM to mechanisms such as ECMP processing (e.g. load-balancing schemes based on packet length could be impacted by the increased packet size due to IOAM), path MTU (i.e. ensure that the MTU of all links within a domain is sufficiently large to support the increased packet size due to IOAM) and ICMP message handling (i.e. in case of a native IPv6 transport, IOAM support for ICMPv6 Echo Request/Reply could desired which would translate into ICMPv6 extensions to enable IOAM data fields to be copied from an Echo Request message to an Echo Reply message).

IOAM control points: IOAM data fields are added to or removed from the live user traffic by the devices which form the edge of a domain. Devices within an IOAM domain can update and/or add IOAM data-fields. Domain edge devices can be hosts or network devices.

Traffic-sets that IOAM is applied to: IOAM can be deployed on all or only on subsets of the live user traffic. It SHOULD be possible to enable IOAM on a selected set of traffic (e.g., per interface, based on an access control list or flow specification defining a specific set of traffic, etc.) The selected set of traffic can also be all traffic.

Encapsulation independence: Data formats for IOAM SHOULD be defined in a transport-independent manner. IOAM applies to a variety of encapsulating protocols. A definition of how IOAM data fields are carried by different transport protocols is outside the scope of this document.

Layering: If several encapsulation protocols (e.g., in case of tunneling) are stacked on top of each other, IOAM data-records could be present at every layer. The behavior follows the ships-in-the-night model, i.e. IOAM data in one layer is independent from IOAM data in another layer. Layering allows operators to instrument the protocol layer they want to measure. The different layers could, but do not have to share the same IOAM encapsulation and decapsulation.

Combination with active OAM mechanisms: IOAM should be usable for active network probing, enabling for example a customized version of traceroute. IOAM may also be carried out on cloned or sampled copies of data packets, when the operator prefers not to directly modify data packets for IOAM purposes. Decapsulating IOAM nodes must have the ability to discard active IOAM packets, potentially in addition to retrieving the IOAM information.

IOAM implementation: The IOAM data-field definitions take the specifics of devices with hardware data-plane and software data-plane into account.

4. IOAM Data Types and Formats

This section defines IOAM data types and data fields and associated data types required for IOAM.

To accommodate the different uses of IOAM, IOAM data fields fall into different categories, as specified below. In IOAM these categories are referred to as IOAM-Types. A common registry is maintained for IOAM-Types, see Section 7.2 for details. Corresponding to these IOAM-Types, different IOAM data fields are defined. IOAM data fields can be encapsulated into a variety of protocols, such as NSH, Geneve, IPv6, etc. The definition of how IOAM data fields are encapsulated into other protocols is outside the scope of this document.

This document defines four IOAM-Types, as specified in this section:

IOAM is expected to be deployed in a specific domain rather than on the overall Internet. The part of the network which employs IOAM is referred to as the "IOAM-domain". IOAM data is added to a packet upon entering the IOAM-domain and is removed from the packet when exiting the domain. Within the IOAM-domain, the IOAM data may be updated by network nodes that the packet traverses. The device which adds an IOAM data container to the packet to capture IOAM data is called the "IOAM encapsulating node", whereas the device which removes the IOAM data container is referred to as the "IOAM decapsulating node". Nodes within the domain which are aware of IOAM data and read and/or write or process the IOAM data are called "IOAM transit nodes". IOAM nodes which add or remove the IOAM data fields can also update the IOAM data fields at the same time. Or in other words, IOAM encapsulating or decapsulating nodes can also serve as IOAM transit nodes at the same time. Note that not every node in an IOAM domain needs to be an IOAM transit node. For example, a deployment might require that packets traverse a set of firewalls. In that case, only the set of firewall nodes would be IOAM transit nodes rather than all nodes.

An IOAM encapsulating node incorporates one or more IOAM-Types (from the list of four IOAM-Types above) into packets that IOAM is enabled for. If IOAM is enabled for a selected subset of the traffic, the encapsulating node is responsible for applying the IOAM functionality to the selected subset.

An IOAM transit node updates one or more of the IOAM data fields. If both the pre-allocated and the incremental trace options are present in the packet, each IOAM transit node will update at most one of these options. A transit node cannot add new IOAM options to a packet, and cannot change an IOAM Edge-to-Edge Option.

An IOAM decapsulating node removes all the IOAM-Types from packets.

The role of a node (i.e. encapsulating, transit, decapsulating) is defined within an IOAM namespace (see below). A node can have different roles in different IOAM namespaces.

4.1. IOAM Namespaces

IOAM data fields are defined within an IOAM namespace. An IOAM namespace is identified by a 16-bit namespace identifier (Namespace-ID). Namespace identifiers MUST be present and populated in all IOAM option headers. The Namespace-ID value is divided into two sub-ranges:

The IANA-assigned range is intended to allow future extensions to have new and interoperable IOAM functionality, while the operator-assigned range is intended to be domain specific, and managed by the network operator. The Namespace-ID value of 0x0000 is default and known to all the nodes implementing IOAM.

Namespace identifiers allow devices which are IOAM capable to determine:

IOAM namespaces support several different uses:

4.2. IOAM Tracing Options

"IOAM tracing data" is expected to be collected at every node that a packet traverses to ensure visibility into the entire path a packet takes within an IOAM domain, i.e., in a typical deployment all nodes in an in-situ OAM-domain would participate in IOAM and thus be IOAM transit nodes, IOAM encapsulating or IOAM decapsulating nodes. If not all nodes within a domain are IOAM capable, IOAM tracing information will only be collected on those nodes which are IOAM capable. Nodes which are not IOAM capable will forward the packet without any changes to the IOAM data fields. The maximum number of hops and the minimum path MTU of the IOAM domain is assumed to be known.

To optimize hardware and software implementations tracing is defined as two separate options. Any deployment MAY choose to configure and support one or both of the following options. An implementation of the transport protocol that carries these in-situ OAM data MAY choose to support only one of the options. In the event that both options are utilized at the same time, the Incremental Trace Option MUST be placed before the Pre-allocated Trace Option. Given that the operator knows which equipment is deployed in a particular IOAM, the operator will decide by means of configuration which type(s) of trace options will be enabled for a particular domain.

Pre-allocated Trace Option:
This trace option is defined as a container of node data fields with pre-allocated space for each node to populate its information. This option is useful for software implementations where it is efficient to allocate the space once and index into the array to populate the data during transit. The IOAM encapsulating node allocates the option header and sets the fields in the option header. The in situ OAM encapsulating node allocates an array which is used to store operational data retrieved from every node while the packet traverses the domain. IOAM transit nodes update the content of the array, and possibly update the checksums of outer headers. A pointer which is part of the IOAM trace data points to the next empty slot in the array. An IOAM transit node that updates the content of the pre-allocated option also updates the value of the pointer, which specifies where the next IOAM transit node fills in its data.
Incremental Trace Option:
This trace option is defined as a container of node data fields where each node allocates and pushes its node data immediately following the option header. This type of trace recording is useful for some of the hardware implementations as this eliminates the need for the transit network elements to read the full array in the option and allows for arbitrarily long packets as the MTU allows. The in-situ OAM encapsulating node allocates the option header. The in-situ OAM encapsulating node based on operational state and configuration sets the fields in the header that control what node data fields should be collected, and how large the node data list can grow. The in-situ OAM transit nodes push their node data to the node data list, decrease the remaining length available to subsequent nodes, and adjust the lengths and possibly checksums in outer headers.

Every node data entry is to hold information for a particular IOAM transit node that is traversed by a packet. The in-situ OAM decapsulating node removes the IOAM data and processes and/or exports the metadata. IOAM data uses its own name-space for information such as node identifier or interface identifier. This allows for a domain-specific definition and interpretation. For example: In one case an interface-id could point to a physical interface (e.g., to understand which physical interface of an aggregated link is used when receiving or transmitting a packet) whereas in another case it could refer to a logical interface (e.g., in case of tunnels).

The following IOAM data is defined for IOAM tracing:

The "node data list" array in the packet is populated iteratively as the packet traverses the network, starting with the last entry of the array, i.e., "node data list [n]" is the first entry to be populated, "node data list [n-1]" is the second one, etc.

4.2.1. Pre-allocated and Incremental Trace Options

The in-situ OAM pre-allocated trace option and the in-situ OAM incremental trace option have similar formats. Except where noted below, the internal formats and fields of the two trace options are identical.

 
Pre-allocated and incremental trace option headers:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|        Namespace-ID           |NodeLen  | Flags | RemainingLen|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|               IOAM-Trace-Type                 |  Reserved     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


The trace option data MUST be 4-octet aligned:

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
|                                                               |  |
|                        node data list [0]                     |  |
|                                                               |  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  D
|                                                               |  a
|                        node data list [1]                     |  t
|                                                               |  a
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  
~                             ...                               ~  S
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  p
|                                                               |  a
|                        node data list [n-1]                   |  c
|                                                               |  e
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |
|                                                               |  |
|                        node data list [n]                     |  |
|                                                               |  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+


Namespace-ID:
16-bit identifier of an IOAM namespace. The Namespace-ID value of 0x0000 is defined as the default value and MUST be known to all the nodes implementing IOAM. For any other Namespace-ID value that does not match any Namespace-ID the node is configured to operate on, the node MUST NOT change the contents of the IOAM data fields.
NodeLen:
5-bit unsigned integer. This field specifies the length of data added by each node in multiples of 4-octets, excluding the length of the "Opaque State Snapshot" field.

If IOAM-Trace-Type bit 7 is not set, then NodeLen specifies the actual length added by each node. If IOAM-Trace-Type bit 7 is set, then the actual length added by a node would be (NodeLen + Opaque Data Length).

For example, if 3 IOAM-Trace-Type bits are set and none of them are wide, then NodeLen would be 3. If 3 IOAM-Trace-Type bits are set and 2 of them are wide, then NodeLen would be 5.

An IOAM encapsulating node must set NodeLen.

A node receiving an IOAM Pre-allocated or Incremental Trace Option may rely on the NodeLen value, or it may ignore the NodeLen value and calculate the node length from the IOAM-Trace-Type bits.
Flags
4-bit field. The following flags are defined:
Bit 0
"Overflow" (O-bit) (most significant bit). This bit is set by the network element if there is not enough number of octets left to record node data, no field is added and the overflow "O-bit" must be set to "1" in the header. This is useful for transit nodes to ignore further processing of the option.
Bit 1
"Loopback" (L-bit). Loopback mode is used to send a copy of a packet back towards the source. Loopback mode assumes that a return path from transit nodes and destination nodes towards the source exists. The encapsulating node decides (e.g., using a filter) which packets loopback mode is enabled for by setting the loopback bit. The encapsulating node also needs to ensure that sufficient space is available in the IOAM header for loopback operation, which includes intermediate nodes adding trace data on the original path and then again on the return path. A loopback bit that is set indicates to the transit nodes processing this option that they are to create a copy of the received packet and send the copy back to the source of the packet. The copy has its metadata added after being copied in order to allow any egress-dependent information to be set based on the egress of the copy rather than the original. The original packet continues towards its destination. The source address of the original packet is used as the destination address in the copied packet. The address of the node performing the copy operation is used as the source address. The L-bit MUST be cleared in the copy of the packet that a node sends back towards the source. On its way back towards the source, the copied packet is processed like any other packet with IOAM information, including adding any requested data at each transit node (assuming there is sufficient space). Once the return packet reaches the IOAM domain boundary, IOAM decapsulation occurs as with any other packet containing IOAM information. Because any intermediate node receiving such a packet would not know how to process the original packet, and because there would be a risk of the original packet leaking past the initiator of the IOAM loopback, the initiator of an IOAM loopback MUST be the initiator of the packet. Once a loopback packet is received back at the initiator, it is a local matter how it is recognized as a loopback packet.
Bit 2
"Active" (A-bit). When set, this indicates that this is an active OAM packet, where "active" is used in the sense defined in [RFC7799], rather than a data packet. For example, the packet may be a probe, or it may be a (possibly truncated) copy of a data packet. At the IOAM decapsulating node, in addition to processing and/or exporting the metadata, the packet must be discarded rather than forwarded. If this bit is not set, then the decapsulating node should attempt to forward the packet after IOAM decapsulation.
Bit 3
"Immediate Export" (I-bit). Immediate export mode is used to export IOAM data fields immediately at every IOAM supported network node, instead of adding the IOAM data fields to the packet traversing the network. The various types of IOAM nodes MUST process packets with the I-bit set as follows:
  1. An encapsulating IOAM node configured to set the I-bit encapsulates the packet with the IOAM header and sets the I-bit, leaving the IOAM header without locally collected data, and exports the requested IOAM data immediately. The encapsulating IOAM node is the only type of node allowed to set the I-bit.
  2. A transit node that processes a packet with the I-bit set is expected to export the requested IOAM data, and not incorporate it into the IOAM header.
  3. A decapsulating IOAM node that processes a packet with the I-bit set is expected to export the requested IOAM data, and decapsulate the IOAM header.
Note that in case of "Immediate Export" being employed, no IOAM trace data is added to the packets traversing the network. As a means to support correlation of exported IOAM data different nodes in the network, a deployment could consider attaching an IOAM E2E option in addition to the trace option, that includes a sequence number. See Bit 1 in the IOAM-E2E-Types. Please refer to Section 6 for a discussion of IOAM data export and associated formats.
RemainingLen:
7-bit unsigned integer. This field specifies the data space in multiples of 4-octets remaining for recording the node data, before the node data list is considered to have overflowed. When RemainingLen reaches 0, nodes are no longer allowed to add node data. Given that the sender knows the minimum path MTU, the sender MAY set the initial value of RemainingLen according to the number of node data bytes allowed before exceeding the MTU. Subsequent nodes can carry out a simple comparison between RemainingLen and NodeLen, along with the length of the "Opaque State Snapshot" if applicable, to determine whether or not data can be added by this node. When node data is added, the node MUST decrease RemainingLen by the amount of data added. In the pre-allocated trace option, this is used as an offset in data space to record the node data element.
IOAM-Trace-Type:
A 24-bit identifier which specifies which data types are used in this node data list.
The IOAM-Trace-Type value is a bit field. The following bit fields are defined in this document, with details on each field described in the Section 4.2.2. The order of packing the data fields in each node data element follows the bit order of the IOAM-Trace-Type field, as follows:
Bit 0
(Most significant bit) When set indicates presence of Hop_Lim and node_id in the node data.
Bit 1
When set indicates presence of ingress_if_id and egress_if_id (short format) in the node data.
Bit 2
When set indicates presence of timestamp seconds in the node data.
Bit 3
When set indicates presence of timestamp subseconds in the node data.
Bit 4
When set indicates presence of transit delay in the node data.
Bit 5
When set indicates presence of namespace specific data (short format) in the node data.
Bit 6
When set indicates presence of queue depth in the node data.
Bit 7
When set indicates presence of variable length Opaque State Snapshot field.
Bit 8
When set indicates presence of Hop_Lim and node_id in wide format in the node data.
Bit 9
When set indicates presence of ingress_if_id and egress_if_id in wide format in the node data.
Bit 10
When set indicates presence of namespace specific data in wide format in the node data.
Bit 11
When set indicates presence of buffer occupancy in the node data.
Bit 12-22
Undefined. An IOAM encapsulating node MUST set the value of each of these bits to 0. If an IOAM transit node receives a packet with one or more of these bits set to 1, it must either:
  1. Add corresponding node data filled with the reserved value 0xFFFFFFFF, after the node data fields for the IOAM-Trace-Type bits defined above, such that the total node data added by this node in units of 4-octets is equal to NodeLen, or
  2. Not add any node data fields to the packet, even for the IOAM-Trace-Type bits defined above.
Bit 23
When set indicates presence of the Checksum Complement node data.
Section 4.2.2 describes the IOAM data types and their formats. Within an in-situ OAM domain possible combinations of these bits making the IOAM-Trace-Type can be restricted by configuration knobs.
Reserved:
8-bits. Must be zero.
Node data List [n]:
Variable-length field. The type of which is determined by the IOAM-Trace-Type bit representing the n-th node data in the node data list. The node data list is encoded starting from the last node data of the path. The first element of the node data list (node data list [0]) contains the last node of the path while the last node data of the node data list (node data list[n]) contains the first node data of the path traced. Populating the node data list in this way ensures that the order of node data list is the same for incremental and pre-allocated trace options. In the pre-allocated trace option, the index contained in RemainingLen identifies the offset for current active node data to be populated.

4.2.2. IOAM node data fields and associated formats

All the data fields MUST be 4-octet aligned. If a node which is supposed to update an IOAM data field is not capable of populating the value of a field set in the IOAM-Trace-Type, the field value MUST be set to 0xFFFFFFFF for 4-octet fields or 0xFFFFFFFFFFFFFFFF for 8-octet fields, indicating that the value is not populated, except when explicitly specified in the field description below.

Data field and associated data type for each of the data field is shown below:

 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|   Hop_Lim     |              node_id                          |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|     ingress_if_id             |         egress_if_id          |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|O|                     transit delay                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                    namespace specific data                    |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       queue depth                             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Length      |                     Schema ID                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   |                                                               |
   |                        Opaque data                            |
   ~                                                               ~
   .                                                               .
   .                                                               .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|   Hop_Lim     |              node_id                          ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~                         node_id (contd)                       |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       ingress_if_id                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       egress_if_id                            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                    namespace specific data                    ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~                namespace specific data (contd)                |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       buffer occupancy                        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|      Checksum Complement      |           Reserved            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Hop_Lim and node_id:
4-octet field defined as follows:
Hop_Lim:
1-octet unsigned integer. It is set to the Hop Limit value in the packet at the node that records this data. Hop Limit information is used to identify the location of the node in the communication path. This is copied from the lower layer, e.g., TTL value in IPv4 header or hop limit field from IPv6 header of the packet when the packet is ready for transmission. The semantics of the Hop_Lim field depend on the lower layer protocol that IOAM is encapsulated over, and therefore its specific semantics are outside the scope of this memo.
node_id:
3-octet unsigned integer. Node identifier field to uniquely identify a node within in-situ OAM domain. The procedure to allocate, manage and map the node_ids is beyond the scope of this document.
ingress_if_id and egress_if_id:
4-octet field defined as follows:
ingress_if_id:
2-octet unsigned integer. Interface identifier to record the ingress interface the packet was received on.
egress_if_id:
2-octet unsigned integer. Interface identifier to record the egress interface the packet is forwarded out of.

Note that due to the fact that IOAM uses its own namespaces for IOAM data fields, data fields like interface identifiers can be used in a flexible way to represent system resources that are associated with ingressing or egressing packets, i.e. an IOAM interface ID could represent a physical interface, a virtual or logical interface, or even a queue.

timestamp seconds:
4-octet unsigned integer. Absolute timestamp in seconds that specifies the time at which the packet was received by the node. This field has three possible formats; based on either PTP [IEEE1588v2], NTP [RFC5905], or POSIX [POSIX]. The three timestamp formats are specified in Section 5. In all three cases, the Timestamp Seconds field contains the 32 most significant bits of the timestamp format that is specified in Section 5. If a node is not capable of populating this field, it assigns the value 0xFFFFFFFF. Note that this is a legitimate value that is valid for 1 second in approximately 136 years; the analyzer should correlate several packets or compare the timestamp value to its own time-of-day in order to detect the error indication.
timestamp subseconds:
4-octet unsigned integer. Absolute timestamp in subseconds that specifies the time at which the packet was received by the node. This field has three possible formats; based on either PTP [IEEE1588v2], NTP [RFC5905], or POSIX [POSIX]. The three timestamp formats are specified in Section 5. In all three cases, the Timestamp Subseconds field contains the 32 least significant bits of the timestamp format that is specified in Section 5. If a node is not capable of populating this field, it assigns the value 0xFFFFFFFF. Note that this is a legitimate value in the NTP format, valid for approximately 233 picoseconds in every second. If the NTP format is used the analyzer should correlate several packets in order to detect the error indication.
transit delay:
4-octet unsigned integer in the range 0 to 2^31-1. It is the time in nanoseconds the packet spent in the transit node. This can serve as an indication of the queuing delay at the node. If the transit delay exceeds 2^31-1 nanoseconds then the top bit 'O' is set to indicate overflow and value set to 0x80000000. When this field is part of the data field but a node populating the field is not able to fill it, the field position in the field must be filled with value 0xFFFFFFFF to mean not populated.
namespace specific data:
4-octet field which can be used by the node to add namespace specific data. This represents a "free-format" 4-octet bit field with its semantics defined in the context of a specific namespace.
queue depth:
4-octet unsigned integer field. This field indicates the current length of the egress interface queue of the interface from where the packet is forwarded out. The queue depth is expressed as the current number of memory buffers used by the queue (a packet may consume one or more memory buffers, depending on its size).
Opaque State Snapshot:
Variable length field. It allows the network element to store an arbitrary state in the node data field, without a pre-defined schema. The schema is to be defined within the context of a namespace. The schema needs to be made known to the analyzer by some out-of-band mechanism. The specification of this mechanism is beyond the scope of this document. A 24-bit "Schema Id" field, interpreted within the context of a namespace, indicates which particular schema is used, and should be configured on the network element by the operator.
Length:
1-octet unsigned integer. It is the length in multiples of 4-octets of the Opaque data field that follows Schema Id.
Schema ID:
3-octet unsigned integer identifying the schema of Opaque data.
Opaque data:
Variable length field. This field is interpreted as specified by the schema identified by the Schema ID.

When this field is part of the data field but a node populating the field has no opaque state data to report, the Length must be set to 0 and the Schema ID must be set to 0xFFFFFF to mean no schema.

Hop_Lim and node_id wide:
8-octet field defined as follows:
Hop_Lim:
1-octet unsigned integer. It is set to the Hop Limit value in the packet at the node that records this data. Hop Limit information is used to identify the location of the node in the communication path. This is copied from the lower layer for e.g. TTL value in IPv4 header or hop limit field from IPv6 header of the packet. The semantics of the Hop_Lim field depend on the lower layer protocol that IOAM is encapsulated over, and therefore its specific semantics are outside the scope of this memo.
node_id:
7-octet unsigned integer. Node identifier field to uniquely identify a node within in-situ OAM domain. The procedure to allocate, manage and map the node_ids is beyond the scope of this document.
ingress_if_id and egress_if_id wide:
8-octet field defined as follows:
ingress_if_id:
4-octet unsigned integer. Interface identifier to record the ingress interface the packet was received on.
egress_if_id:
4-octet unsigned integer. Interface identifier to record the egress interface the packet is forwarded out of.
namespace specific data wide:
8-octet field which can be used by the node to add namespace specific data. This represents a "free-format" 8-octet bit field with its semantics defined in the context of a specific namespace.
buffer occupancy:
4-octet unsigned integer field. This field indicates the current status of the occupancy of the common buffer pool used by a set of queues. The units of this field depend on the equipment type and deployment and has to be interpreted within the context of a namespace and/or node-id if used.
Checksum Complement:
4-octet node data which contains a two-octet Checksum Complement field, and a 2-octet reserved field. The Checksum Complement is useful when IOAM is transported over encapsulations that make use of a UDP transport, such as VXLAN-GPE or Geneve. Without the Checksum Complement, nodes adding IOAM node data must update the UDP Checksum field. When the Checksum Complement is present, an IOAM encapsulating node or IOAM transit node adding node data MUST carry out one of the following two alternatives in order to maintain the correctness of the UDP Checksum value:
  1. Recompute the UDP Checksum field.
  2. Use the Checksum Complement to make a checksum-neutral update in the UDP payload; the Checksum Complement is assigned a value that complements the rest of the node data fields that were added by the current node, causing the existing UDP Checksum field to remain correct.

IOAM decapsulating nodes MUST recompute the UDP Checksum field, since they do not know whether previous hops modified the UDP Checksum field or the Checksum Complement field.



Checksum Complement fields are used in a similar manner in [RFC7820] and [RFC7821].

4.2.3. Examples of IOAM node data

An entry in the "node data list" array can have different formats, following the needs of the deployment. Some deployments might only be interested in recording the node identifiers, whereas others might be interested in recording node identifier and timestamp. The section defines different types that an entry in "node data list" can take.

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     ingress_if_id             |         egress_if_id          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                     timestamp subseconds                      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    namespace specific data                    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     ingress_if_id             |         egress_if_id          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                   timestamp subseconds                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    namespace specific data                    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    timestamp subseconds                       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    namespace specific data                    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      timestamp seconds                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    timestamp subseconds                       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Length      |                     Schema Id                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |                                                               |
    |                        Opaque data                            |
    ~                                                               ~
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Hop_Lim     |              node_id                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         node_id(contd)                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

0xD40000:
IOAM-Trace-Type is 0xD40000 then the format of node data is:
0xC00000:
IOAM-Trace-Type is 0xC00000 then the format is:
0x900000:
IOAM-Trace-Type is 0x900000 then the format is:
0x840000:
IOAM-Trace-Type is 0x840000 then the format is:
0x940000:
IOAM-Trace-Type is 0x940000 then the format is:
0x318000:
IOAM-Trace-Type is 0x318000 then the format is:

4.3. IOAM Proof of Transit Option

IOAM Proof of Transit data is to support the path or service function chain [RFC7665] verification use cases. Proof-of-transit uses methods like nested hashing or nested encryption of the IOAM data or mechanisms such as Shamir's Secret Sharing Schema (SSSS). While details on how the IOAM data for the proof of transit option is processed at IOAM encapsulating, decapsulating and transit nodes are outside the scope of the document, all of these approaches share the need to uniquely identify a packet as well as iteratively operate on a set of information that is handed from node to node. Correspondingly, two pieces of information are added as IOAM data to the packet:

 
IOAM proof of transit option header:
 
 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|       Namespace-ID            |IOAM POT Type  | IOAM POT flags| 
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

IOAM proof of transit option data MUST be 4-octet aligned.:
    
 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|       POT Option data field determined by IOAM-POT-Type       |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


Namespace-ID:
16-bit identifier of an IOAM namespace. The Namespace-ID value of 0x0000 is defined as the default value and MUST be known to all the nodes implementing IOAM. For any other Namespace-ID value that does not match any Namespace-ID the node is configured to operate on, the node MUST NOT change the contents of the IOAM data fields.
IOAM POT Type:
8-bit identifier of a particular POT variant that specifies the POT data that is included. This document defines POT Type 0:
0:
POT data is a 16 Octet field as described below.
IOAM POT flags:
8-bit. Following flags are defined:
Bit 0
"Profile-to-use" (P-bit) (most significant bit). For IOAM POT types that use a maximum of two profiles to drive computation, indicates which POT-profile is used. The two profiles are numbered 0, 1.
Bit 1-7
Reserved: Must be set to zero upon transmission and ignored upon receipt.
POT Option data:
Variable-length field. The type of which is determined by the IOAM-POT-Type.

4.3.1. IOAM Proof of Transit Type 0

 
IOAM proof of transit option of IOAM POT Type 0:
 
 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|        Namespace-ID           |IOAM POT Type=0|P|R R R R R R R|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
|                           Random                              |  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  P
|                        Random(contd)                          |  O
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  T
|                         Cumulative                            |  | 
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |
|                         Cumulative (contd)                    |  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+


Namespace-ID:
16-bit identifier of an IOAM namespace. The Namespace-ID value of 0x0000 is defined as the default value and MUST be known to all the nodes implementing IOAM. For any other Namespace-ID value that does not match any Namespace-ID the node is configured to operate on, the node MUST NOT change the contents of the IOAM data fields.
IOAM POT Type:
8-bit identifier of a particular POT variant that specifies the POT data that is included. This section defines the POT data when the IOAM POT Type is set to the value 0.
P bit:
1-bit. "Profile-to-use" (P-bit) (most significant bit). Indicates which POT-profile is used to generate the Cumulative. Any node participating in POT will have a maximum of 2 profiles configured that drive the computation of cumulative. The two profiles are numbered 0, 1. This bit conveys whether profile 0 or profile 1 is used to compute the Cumulative.
R (7 bits):
7-bit IOAM POT flags for future use. MUST be set to zero upon transmission and ignored upon receipt.
Random:
64-bit Per packet Random number.
Cumulative:
64-bit Cumulative that is updated at specific nodes by processing per packet Random number field and configured parameters.

Note: Larger or smaller sizes of "Random" and "Cumulative" data are feasible and could be required for certain deployments (e.g. in case of space constraints in the transport protocol used). Future versions of this document will address different sizes of data for "proof of transit".

4.4. IOAM Edge-to-Edge Option

The IOAM edge-to-edge option is to carry data that is added by the IOAM encapsulating node and interpreted by IOAM decapsulating node. The IOAM transit nodes MAY process the data without modifying it.

  IOAM edge-to-edge option header:
   
    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Namespace-ID           |         IOAM-E2E-Type         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   IOAM edge-to-edge option data MUST be 4-octet aligned:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       E2E Option data field determined by IOAM-E2E-Type       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Namespace-ID:
16-bit identifier of an IOAM namespace. The Namespace-ID value of 0x0000 is defined as the default value and MUST be known to all the nodes implementing IOAM. For any other Namespace-ID value that does not match any Namespace-ID the node is configured to operate on, then the node MUST NOT change the contents of the IOAM data fields.
IOAM-E2E-Type:
A 16-bit identifier which specifies which data types are used in the E2E option data. The IOAM-E2E-Type value is a bit field. The order of packing the E2E option data field elements follows the bit order of the IOAM-E2E-Type field, as follows:
Bit 0
(Most significant bit) When set indicates presence of a 64-bit sequence number added to a specific "packet group" which is used to detect packet loss, packet reordering, or packet duplication within the group. The "packet group" is deployment dependent and defined at the IOAM encapsulating node e.g. by n-tuple based classification of packets.
Bit 1
When set indicates presence of a 32-bit sequence number added to a specific "packet group" which is used to detect packet loss, packet reordering, or packet duplication within that group. The "packet group" is deployment dependent and defined at the IOAM encapsulating node e.g. by n-tuple based classification of packets.
Bit 2
When set indicates presence of timestamp seconds for the transmission of the frame. This 4-octet field has three possible formats; based on either PTP [IEEE1588v2], NTP [RFC5905], or POSIX [POSIX]. The three timestamp formats are specified in Section 5. In all three cases, the Timestamp Seconds field contains the 32 most significant bits of the timestamp format that is specified in Section 5. If a node is not capable of populating this field, it assigns the value 0xFFFFFFFF. Note that this is a legitimate value that is valid for 1 second in approximately 136 years; the analyzer should correlate several packets or compare the timestamp value to its own time-of-day in order to detect the error indication.
Bit 3
When set indicates presence of timestamp subseconds for the transmission of the frame. This 4-octet field has three possible formats; based on either PTP [IEEE1588v2], NTP [RFC5905], or POSIX [POSIX]. The three timestamp formats are specified in Section 5. In all three cases, the Timestamp Subseconds field contains the 32 least significant bits of the timestamp format that is specified in Section 5. If a node is not capable of populating this field, it assigns the value 0xFFFFFFFF. Note that this is a legitimate value in the NTP format, valid for approximately 233 picoseconds in every second. If the NTP format is used the analyzer should correlate several packets in order to detect the error indication.
Bit 4-15
Undefined. An IOAM encapsulating node Must set the value of these bits to zero upon transmission and ignore upon receipt.
E2E Option data:
Variable-length field. The type of which is determined by the IOAM-E2E-Type.

5. Timestamp Formats

The IOAM data fields include a timestamp field which is represented in one of three possible timestamp formats. It is assumed that the management plane is responsible for determining which timestamp format is used.

5.1. PTP Truncated Timestamp Format

The Precision Time Protocol (PTP) [IEEE1588v2] uses an 80-bit timestamp format. The truncated timestamp format is a 64-bit field, which is the 64 least significant bits of the 80-bit PTP timestamp. The PTP truncated format is specified in Section 4.3 of [I-D.ietf-ntp-packet-timestamps], and the details are presented below for the sake of completeness.

         
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            Seconds                            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          Nanoseconds                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
           

Figure 1: PTP [IEEE1588v2] Truncated Timestamp Format

Timestamp field format:

Epoch:

Resolution:

Wraparound:

Synchronization Aspects:

5.2. NTP 64-bit Timestamp Format

The Network Time Protocol (NTP) [RFC5905] timestamp format is 64 bits long. This format is specified in Section 4.2.1 of [I-D.ietf-ntp-packet-timestamps], and the details are presented below for the sake of completeness.

         
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            Seconds                            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            Fraction                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
           

Figure 2: NTP [RFC5905] 64-bit Timestamp Format

Timestamp field format:

Epoch:

Resolution:

Wraparound:

Synchronization Aspects:

5.3. POSIX-based Timestamp Format

This timestamp format is based on the POSIX time format [POSIX]. The detailed specification of the timestamp format used in this document is presented below.

         
     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            Seconds                            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                          Microseconds                         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
           

Figure 3: POSIX-based Timestamp Format

Timestamp field format:

Epoch:

Resolution:

Wraparound:

Synchronization Aspects:

6. IOAM Data Export

IOAM nodes collect information for packets traversing a domain that supports IOAM. IOAM decapsulating nodes as well as IOAM transit nodes can choose to retrieve IOAM information from the packet, process the information further and export the information using e.g., IPFIX. The mechanisms and associated data formats for exporting IOAM data is outside the scope of this document.

Raw data export of IOAM data using IPFIX is discussed in [I-D.spiegel-ippm-ioam-rawexport].

7. IANA Considerations

This document requests the following IANA Actions.

7.1. Creation of a new In-Situ OAM Protocol Parameters Registry (IOAM) Protocol Parameters IANA registry

IANA is requested to create a new protocol registry for "In-Situ OAM (IOAM) Protocol Parameters". This is the common registry that will include registrations for all IOAM namespaces. Each Registry, whose names are listed below:

[RFC8126].

will contain the current set of possibilities defined in this document. New registries in this name space are created via RFC Required process as per

The subsequent sub-sections detail the registries herein contained.

7.2. IOAM Type Registry

This registry defines 128 code points for the IOAM-Type field for identifying IOAM options as explained in Section 4. The following code points are defined in this draft:

[RFC8126].

0
IOAM Pre-allocated Trace Option Type
1
IOAM Incremental Trace Option Type
2
IOAM POT Option Type
3
IOAM E2E Option Type

4 - 127 are available for assignment via RFC Required process as per

7.3. IOAM Trace Type Registry

This registry defines code point for each bit in the 24-bit IOAM-Trace-Type field for Pre-allocated trace option and Incremental trace option defined in Section 4.2. The meaning of Bits 0 - 11 for trace type are defined in this document in Paragraph 5 of Section 4.2.1:

[RFC8126].

Bit 0
hop_Lim and node_id in short format
Bit 1
ingress_if_id and egress_if_id in short format
Bit 2
timestamp seconds
Bit 3
timestamp subseconds
Bit 4
transit delay
Bit 5
namespace specific data in short format
Bit 6
queue depth
Bit 7
variable length Opaque State Snapshot
Bit 8
hop_Lim and node_id in wide format
Bit 9
ingress_if_id and egress_if_id in wide format
Bit 10
namespace specific data in wide format
Bit 11
buffer occupancy
Bit 23
checksum complement

The meaning for Bits 12 - 22 are available for assignment via RFC Required process as per

7.4. IOAM Trace Flags Registry

This registry defines code points for each bit in the 4 bit flags for Pre-allocated trace option and Incremental trace option defined in Section 4.2. The meaning of Bit 0 - 2 for trace flags are defined in this document in Paragraph 3 of Section 4.2.1:

Bit 0
"Overflow" (O-bit)
Bit 1
"Loopback" (L-bit)
Bit 2
"Active" (A-bit)
Bit 3
"Immediate Export" (I-bit)

7.5. IOAM POT Type Registry

This registry defines 256 code points to define IOAM POT Type for IOAM proof of transit option Section 4.3. The code point value 0 is defined in this document:

[RFC8126].

0:
16 Octet POT data

1 - 255 are available for assignment via RFC Required process as per

7.6. IOAM POT Flags Registry

This registry defines code points for each bit in the 8 bit flags for IOAM POT option defined in Section 4.3. The meaning of Bit 0 for IOAM POT flags is defined in this document in Section 4.3:

[RFC8126].

Bit 0
"Profile-to-use" (P-bit)

The meaning for Bits 1 - 7 are available for assignment via RFC Required process as per

7.7. IOAM E2E Type Registry

This registry defines code points for each bit in the 16 bit IOAM-E2E-Type field for IOAM E2E option Section 4.4. The meaning of Bit 0 - 3 are defined in this document:

[RFC8126].

Bit 0
64-bit sequence number
Bit 1
32-bit sequence number
Bit 2
timestamp seconds
Bit 3
timestamp subseconds

The meaning of Bits 4 - 15 are available for assignment via RFC Required process as per

7.8. IOAM Namespace-ID Registry

IANA is requested to set up an "IOAM Namespace-ID Registry", containing 16-bit values. The meaning of Bit 0 is defined in this document. IANA is requested to reserve the values 0x0001 to 0x7FFF for private use (managed by operators), as specified in Section 4.1 of the current document. Registry entries for the values 0x8000 to 0xFFFF are to be assigned via the "Expert Review" policy defined in [RFC8126].

0:
default namespace (known to all IOAM nodes)
0x0001 - 0x7FFF:
reserved for private use
0x8000 - 0xFFFF:
unassigned

8. Security Considerations

As discussed in [RFC7276], a successful attack on an OAM protocol in general, and specifically on IOAM, can prevent the detection of failures or anomalies, or create a false illusion of nonexistent ones.

The Proof of Transit option (Section Section 4.3) is used for verifying the path of data packets. The security considerations of POT are further discussed in [I-D.brockners-proof-of-transit].

The data elements of IOAM can be used for network reconnaissance, allowing attackers to collect information about network paths, performance, queue states, buffer occupancy and other information. Note that in case IOAM is used in "immediate export" mode, the IOAM related trace information would not be available in the customer data packets, but would be exported by every IOAM node. IOAM data export and securing IOAM data export is outside the scope of this document.

IOAM can be used as a means for implementing Denial of Service (DoS) attacks, or for amplifying them. For example, a malicious attacker can add an IOAM header to packets in order to consume the resources of network devices that take part in IOAM or collectors that analyze the IOAM data. Another example is a packet length attack, in which an attacker pushes IOAM headers into data packets, causing these packets to be increased beyond the MTU size, resulting in fragmentation or in packet drops.

Since IOAM options may include timestamps, if network devices use synchronization protocols then any attack on the time protocol [RFC7384] can compromise the integrity of the timestamp-related data fields.

At the management plane, attacks may be implemented by misconfiguring or by maliciously configuring IOAM-enabled nodes in a way that enables other attacks. Thus, IOAM configuration should be secured in a way that authenticates authorized users and verifies the integrity of configuration procedures.

Notably, IOAM is expected to be deployed in specific network domains, thus confining the potential attack vectors to within the network domain. Indeed, in order to limit the scope of threats to within the current network domain the network operator is expected to enforce policies that prevent IOAM traffic from leaking outside of the IOAM domain, and prevent IOAM data from outside the domain to be processed and used within the domain. Another way to prevent the data to get leaked is using the Immediate Export mode of the trace option.

9. Acknowledgements

The authors would like to thank Eric Vyncke, Nalini Elkins, Srihari Raghavan, Ranganathan T S, Karthik Babu Harichandra Babu, Akshaya Nadahalli, LJ Wobker, Erik Nordmark, Vengada Prasad Govindan, Andrew Yourtchenko, Aviv Kfir, Tianran Zhou, Haoyu song and Robin <lizhenbin@huawei.com> for the comments and advice.

This document leverages and builds on top of several concepts described in [I-D.kitamura-ipv6-record-route]. The authors would like to acknowledge the work done by the author Hiroshi Kitamura and people involved in writing it.

The authors would like to gracefully acknowledge useful review and insightful comments received from Joe Clarke, Al Morton, and Mickey Spiegel.

The authors would like to acknowledge the contribution of "Immediate export" of IOAM trace by Barak Gafni.

10. References

10.1. Normative References

[IEEE1588v2] Institute of Electrical and Electronics Engineers, "IEEE Std 1588-2008 - IEEE Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems", IEEE Std 1588-2008, 2008.
[POSIX] Institute of Electrical and Electronics Engineers, "IEEE Std 1003.1-2008 (Revision of IEEE Std 1003.1-2004) - IEEE Standard for Information Technology - Portable Operating System Interface (POSIX(R))", IEEE Std 1003.1-2008, 2008.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997.
[RFC5905] Mills, D., Martin, J., Burbank, J. and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010.
[RFC8126] Cotton, M., Leiba, B. and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017.

10.2. Informative References

[I-D.brockners-proof-of-transit] Brockners, F., Bhandari, S., Dara, S., Pignataro, C., Leddy, J., Youell, S., Mozes, D. and T. Mizrahi, "Proof of Transit", Internet-Draft draft-brockners-proof-of-transit-05, May 2018.
[I-D.ietf-ntp-packet-timestamps] Mizrahi, T., Fabini, J. and A. Morton, "Guidelines for Defining Packet Timestamps", Internet-Draft draft-ietf-ntp-packet-timestamps-06, February 2019.
[I-D.ietf-nvo3-geneve] Gross, J., Ganga, I. and T. Sridhar, "Geneve: Generic Network Virtualization Encapsulation", Internet-Draft draft-ietf-nvo3-geneve-09, February 2019.
[I-D.ietf-nvo3-vxlan-gpe] Maino, F., Kreeger, L. and U. Elzur, "Generic Protocol Extension for VXLAN", Internet-Draft draft-ietf-nvo3-vxlan-gpe-06, April 2018.
[I-D.kitamura-ipv6-record-route] Kitamura, H., "Record Route for IPv6 (PR6) Hop-by-Hop Option Extension", Internet-Draft draft-kitamura-ipv6-record-route-00, November 2000.
[I-D.lapukhov-dataplane-probe] Lapukhov, P. and r. remy@barefootnetworks.com, "Data-plane probe for in-band telemetry collection", Internet-Draft draft-lapukhov-dataplane-probe-01, June 2016.
[I-D.spiegel-ippm-ioam-rawexport] Spiegel, M., Brockners, F., Bhandari, S. and R. Sivakolundu, "In-situ OAM raw data export with IPFIX", Internet-Draft draft-spiegel-ippm-ioam-rawexport-01, October 2018.
[RFC7276] Mizrahi, T., Sprecher, N., Bellagamba, E. and Y. Weingarten, "An Overview of Operations, Administration, and Maintenance (OAM) Tools", RFC 7276, DOI 10.17487/RFC7276, June 2014.
[RFC7384] Mizrahi, T., "Security Requirements of Time Protocols in Packet Switched Networks", RFC 7384, DOI 10.17487/RFC7384, October 2014.
[RFC7665] Halpern, J. and C. Pignataro, "Service Function Chaining (SFC) Architecture", RFC 7665, DOI 10.17487/RFC7665, October 2015.
[RFC7799] Morton, A., "Active and Passive Metrics and Methods (with Hybrid Types In-Between)", RFC 7799, DOI 10.17487/RFC7799, May 2016.
[RFC7820] Mizrahi, T., "UDP Checksum Complement in the One-Way Active Measurement Protocol (OWAMP) and Two-Way Active Measurement Protocol (TWAMP)", RFC 7820, DOI 10.17487/RFC7820, March 2016.
[RFC7821] Mizrahi, T., "UDP Checksum Complement in the Network Time Protocol (NTP)", RFC 7821, DOI 10.17487/RFC7821, March 2016.
[RFC8300] Quinn, P., Elzur, U. and C. Pignataro, "Network Service Header (NSH)", RFC 8300, DOI 10.17487/RFC8300, January 2018.

Authors' Addresses

Frank Brockners Cisco Systems, Inc. Hansaallee 249, 3rd Floor DUESSELDORF, NORDRHEIN-WESTFALEN 40549 Germany EMail: fbrockne@cisco.com
Shwetha Bhandari Cisco Systems, Inc. Cessna Business Park, Sarjapura Marathalli Outer Ring Road Bangalore, KARNATAKA 560 087, India EMail: shwethab@cisco.com
Carlos Pignataro Cisco Systems, Inc. 7200-11 Kit Creek Road Research Triangle Park, NC 27709 United States EMail: cpignata@cisco.com
Hannes Gredler RtBrick Inc. EMail: hannes@rtbrick.com
John Leddy Comcast United States EMail: John_Leddy@cable.comcast.com
Stephen Youell JP Morgan Chase 25 Bank Street London, E14 5JP United Kingdom EMail: stephen.youell@jpmorgan.com
Tal Mizrahi Huawei Network.IO Innovation Lab Israel EMail: tal.mizrahi.phd@gmail.com
David Mozes EMail: mosesster@gmail.com
Petr Lapukhov Facebook 1 Hacker Way Menlo Park, CA, 94025 US EMail: petr@fb.com
Remy Chang Barefoot Networks 4750 Patrick Henry Drive Santa Clara, CA, 95054 US
Daniel Bernier Bell Canada Canada EMail: daniel.bernier@bell.ca
John Lemon Broadcom 270 Innovation Drive San Jose, CA 95134 US EMail: john.lemon@broadcom.com