HIP Working Group A. Keranen
Internet-Draft J. Melén
Intended status: Standards Track M. Komu, Ed.
Expires: April 26, 2018 Ericsson
October 23, 2017

Native NAT Traversal Mode for the Host Identity Protocol
draft-ietf-hip-native-nat-traversal-22

Abstract

This document specifies a new Network Address Translator (NAT) traversal mode for the Host Identity Protocol (HIP). The new mode is based on the Interactive Connectivity Establishment (ICE) methodology and UDP encapsulation of data and signaling traffic. The main difference from the previously specified modes is the use of HIP messages for all NAT traversal procedures.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 26, 2018.

Copyright Notice

Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

The Host Identity Protocol (HIP) [RFC7401] is specified to run directly on top of IPv4 or IPv6. However, many middleboxes found in the Internet, such as NATs and firewalls, often allow only UDP or TCP traffic to pass [RFC5207]. Also, especially NATs usually require the host behind a NAT to create a forwarding state in the NAT before other hosts outside of the NAT can contact the host behind the NAT. To overcome this problem, different methods, commonly referred to as NAT traversal techniques, have been developed.

As one solution, the HIP experiment report [RFC6538] mentions that Teredo based NAT traversal for HIP and related ESP traffic (with double tunneling overhead). Another solution is specified in [RFC5770], which will be referred as "Legacy ICE-HIP" in this document. The experimental Legacy ICE-HIP specification combines Interactive Connectivity Establishment (ICE) protocol [I-D.ietf-ice-rfc5245bis] with HIP, so that basically ICE is responsible of NAT traversal and connectivity testing, while HIP is responsible of end-host authentication and IPsec key management. The resulting protocol uses HIP, STUN and ESP messages tunneled over a single UDP flow. The benefit of using ICE and its STUN/TURN messaging formats is that one can re-use the NAT traversal infrastructure already available in the Internet, such as STUN and TURN servers. Also, some middleboxes may be STUN-aware and may be able to do something "smart" when they see STUN being used for NAT traversal.

Implementing a full ICE/STUN/TURN protocol stack as specified in Legacy ICE-HIP results in a considerable amount of effort and code which could be avoided by re-using and extending HIP messages and state machines for the same purpose. Thus, this document specifies an alternative NAT traversal mode referred as "Native ICE-HIP" that employs HIP messaging format instead of STUN or TURN for the connectivity checks, keepalives and data relaying. Native ICE-HIP also specifies how mobility management works in the context of NAT traversal, which is missing from the Legacy ICE-HIP specification. The native specification is also based on HIPv2, whereas legacy specification is based on HIPv1.

Similarly as Legacy ICE-HIP, also this specification builds on the HIP registration extensions [RFC8003] and the base exchange procedure [RFC7401] and its closing procedures, so the reader is recommended to get familiar with the relevant specifications. In a nutshell, the registration extensions allow a HIP Initiator (usually a "client" host) to ask for specific services from a HIP Responder (usually a "server" host). The registration parameters are included in a base exchange, which is essentially a four-way Diffie-Hellman key exchange authenticated using the public keys of the end-hosts. When the hosts negotiate support for ESP [RFC7402] during the base exchange, they can deliver ESP protected application payload to each other. When either of the hosts moves and changes its IP address, the two hosts re-establish connectivity using the mobility extensions [RFC8046]. The reader is also recommended to get familiar with the mobility extensions, but basically it is a three-way procedure, where the mobile host first announces its new location to the peer, and then the peer tests for connectivity (so called return routability check), for which the mobile hosts must respond in order to activate its new location. This specification builds on the mobility procedures, but modifies it to be compatible with ICE. The differences to the mobility extensions specified in Appendix C. It is worth noting that multihoming support as specified in [RFC8047] is left for further study.

This specification builds heavily on the ICE methodology, so it is recommended that the reader is familiar with the ICE specification [I-D.ietf-ice-rfc5245bis] (especially the overview). However, native ICE-HIP does not implement all the features in ICE, and, hence, the different features of ICE are cross referenced using [RFC2119] terminology for clarity. Appendix B explains the differences to ICE.

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].

This document borrows terminology from [RFC5770], [RFC7401], [RFC8046], [RFC4423], [I-D.ietf-ice-rfc5245bis], and [RFC5389]. The following terms recur in the text:

ICE:

Interactive Connectivity Establishment (ICE) protocol as specified in [I-D.ietf-ice-rfc5245bis]
Legacy ICE-HIP:

Refers to the "Basic Host Identity Protocol (HIP) Extensions for Traversal of Network Address Translators" as specified in [RFC5770]. The protocol specified in this document offers an alternative to Legacy ICE-HIP.
Native ICE-HIP:

The protocol specified in this document (Native NAT Traversal Mode for HIP).
Initiator:

The Initiator is the host that initiates the base exchange using I1 message.
Responder:

The Responder is the host that receives the I1 packet from the Initiator.
Control Relay Server

A registrar host that forwards any kind of HIP control plane packets between the Initiator and the Responder. This host is critical because it relays the locators between the Initiator and the Responder, so that they can try to establish a direct communication path with each other. This host is used to replace HIP rendezvous servers [RFC8004] for hosts operating in private address realms. In the Legacy ICE-HIP specification, this host is denoted as "HIP relay server".
.
Control Relay Client:

A requester host that registers to a Control Relay Server requesting it to forward control-plane traffic (i.e. HIP control messages). In the Legacy ICE-HIP specification, this is denoted as "HIP Relay Client".

Data Relay Server:

A registrar host that forwards HIP related data plane packets, such as Encapsulating Security Payload (ESP) [RFC7402], between two hosts. This host implements similar functionality as TURN servers.
Data Relay Client:

A requester host that registers to a Data Relay Server requesting it to forward data-plane traffic (e.g. ESP traffic).

Locator:

As defined in [RFC8046]: "A name that controls how the packet is routed through the network and demultiplexed by the end-host. It may include a concatenation of traditional network addresses such as an IPv6 address and end-to-end identifiers such as an ESP SPI. It may also include transport port numbers or IPv6 Flow Labels as demultiplexing context, or it may simply be a network address."
LOCATOR_SET (written in capital letters):

Denotes a HIP control packet parameter that bundles multiple locators together.
ICE offer:

The Initiator's LOCATOR_SET parameter in a HIP I2 control packet. Corresponds to the ICE offer parameter, but is HIP specific.
ICE answer:

The Responder's LOCATOR_SET parameter in a HIP R2 control packet. Corresponds to the ICE answer parameter, but is HIP specific.
HIP connectivity checks:

In order to obtain a direct end-to-end communication path (without employing a Data Relay Server), two communicating HIP hosts try to "punch holes" through their NAT boxes using this mechanism. It is similar to the ICE connectivity checks, but implemented using HIP return routability checks.
Controlling host:

The controlling host is the Initiator. It nominates the candidate pair to be used with the controlled host.
Controlled host:

The controlled host is the Responder. It waits for the controlling to nominate an address candidate pair.
Checklist:

A list of address candidate pairs that need to be tested for connectivity.
Transport address:

Transport layer port and the corresponding IPv4/v6 address.
Candidate:

A transport address that is a potential point of contact for receiving data.
Host candidate:

A candidate obtained by binding to a specific port from an IP address on the host.
Server reflexive candidate:

A translated transport address of a host as observed by a Control or Data Relay Server.
Peer reflexive candidate:

A translated transport address of a host as observed by its peer.
Relayed candidate:

A transport address that exists on a Data Relay Server. Packets that arrive at this address are relayed towards the Data Relay Client.
Permission:

In the context of Data Relay Server, permission refers to a concept similar to TURN's channels. Before a host can use a relayed candidate to forward traffic through a Data Relay Server, the host must activate the relayed candidate with a specific peer host.
Base:

The base of an candidate is the local source address a host uses to send packets for the associated candidate. For example, the base of a server reflexive address is the local address the host used for registering itself to the associated Control or Data Relay Server. The base of a host candidate is equal to the host candidate itself.

3. Overview of Operation

               +--------------+
               |    Control   |
+--------+     | Relay Server |      +--------+
| Data   |     +----+-----+---+      | Data   |
| Relay  |         /       \         | Relay  |
| Server |        /         \        | Server |
+--------+       /           \       +--------+
                /             \        
               /               \
              /                 \
             /  <- Signaling ->  \
            /                     \
      +-------+                +-------+
      |  NAT  |                |  NAT  |
      +-------+                +-------+
       /                              \
      /                                \
 +-------+                           +-------+
 | Init- |                           | Resp- |
 | iator |                           | onder |
 +-------+                           +-------+

Figure 1: Example Network Configuration

In the example configuration depicted in Figure 1, both Initiator and Responder are behind one or more NATs, and both private networks are connected to the public Internet. To be contacted from behind a NAT, at least the Responder must be registered with a Control Relay Server reachable on the public Internet. The Responder may have also registered to a Data Relay Server that can forward the data plane in case NAT traversal fails. While, strictly speaking, the Initiator does not need any Relay Servers, it may act in the other role for other hosts and connectivity with the Data Relay Server of the Responder may fail, so it is the Initiator may also have registered to a Control and/or Data Relay Server. It is worth noting that a Control and Data Relay does not forge the source address of a passing packet, but always translates the source address and source port of a packet to be forwarded (to its own).

We assume, as a starting point, that the Initiator knows both the Responder's Host Identity Tag (HIT) and the address(es) of the Responder's Control Relay Server(s) (how the Initiator learns of the Responder's Control Relay Server is outside of the scope of this document, but may be through DNS or another name service). The first steps are for both the Initiator and Responder to register with a Control Relay Server (need not be the same one) and gather a set of address candidates. The hosts use either Control Relay Servers or Data Relay Servers (or other infrastructure including STUN or TURN servers) for gathering the candidates. Next, the HIP base exchange is carried out by encapsulating the HIP control packets in UDP datagrams and sending them through the Responder's Control Relay Server. As part of the base exchange, each HIP host learns of the peer's candidate addresses through the HIP offer/answer procedure embedded in the base exchange.

Once the base exchange is completed, two HIP hosts have established a working communication session (for signaling) via a Control Relay Server, but the hosts still have to find a better path, preferably without a Data Relay Server, for the ESP data flow. For this, connectivity checks are carried out until a working pair of addresses is discovered. At the end of the procedure, if successful, the hosts will have established a UDP-based tunnel that traverses both NATs, with the data flowing directly from NAT to NAT or via a Data Relay Server. At this point, also the HIP signaling can be sent over the same address/port pair, and is demultiplexed from IPsec as described in the UDP encapsulation standard for IPsec [RFC3948]. Finally, the two hosts send NAT keepalives as needed in order keep their UDP-tunnel state active in the associated NAT boxes.

If either one of the hosts knows that it is not behind a NAT, hosts can negotiate during the base exchange a different mode of NAT traversal that does not use HIP connectivity checks, but only UDP encapsulation of HIP and ESP. Also, it is possible for the Initiator to simultaneously try a base exchange with and without UDP encapsulation. If a base exchange without UDP encapsulation succeeds, no HIP connectivity checks or UDP encapsulation of ESP are needed.

4. Protocol Description

This section describes the normative behavior of the "Native ICE-HIP" protocol extension. Most of the procedures are similar to what is defined in [RFC5770] but with different, or additional, parameter types and values. In addition, a new type of relaying server, Data Relay Server, is specified. Also, it should be noted that HIP version 2 [RFC7401] (instead of [RFC5201] used in [RFC5770]) is expected to be used with this NAT traversal mode.

4.1. Relay Registration

In order for two hosts to communicate over NATted environments, they need a reliable way to exchange information. To achieve this, "HIP relay server" is defined in [RFC5770]. It supports relaying of HIP control plane traffic over UDP in NATted environments, and forwards HIP control packets between the Initiator and the Responder. In this document, the HIP relay server is denoted as "Control Relay Server" for better alignment with the rest of the terminology. The registration to the Control Relay Server can be achieved using RELAY_UDP_ESP parameter as explained later in this section.

To guarantee also data plane delivery over varying types of NAT devices, a host MAY also register for UDP encapsulated ESP relaying using Registration Type RELAY_UDP_ESP (value [TBD by IANA: 3]). This service may be coupled with the Control Relay Server server or offered separately on another server. If the server supports relaying of UDP encapsulated ESP, the host is allowed to register for a data relaying service using the registration extensions in Section 3.3 of [RFC8003]). If the server has sufficient relaying resources (free port numbers, bandwidth, etc.) available, it opens a UDP port on one of its addresses and signals the address and port to the registering host using the RELAYED_ADDRESS parameter (as defined in Section 5.12 in this document). If the Data Relay Server would accept the data relaying request but does not currently have enough resources to provide data relaying service, it MUST reject the request with Failure Type "Insufficient resources" [RFC8003].

A Control Relay Server MUST silently drop packets to a Control Relay Client that has not previously registered with the HIP relay. The registration process follows the generic registration extensions defined in [RFC8003]. The HIP control plane relaying registration follows [RFC5770], but the data plane registration is different. It is worth noting that if the HIP control and data plane relay services reside on different hosts, the client has to register separately to each of them. In the example shown in Figure 2, the two services are coupled on a single host. The text uses "Relay Client" and "Relay Server" as a shorthand when the procedures apply both to control and data cases.

  Control/Data                                           Control/Data
  Relay Client (Initiator)                   Relay Server (Responder)
  |   1. UDP(I1)                                                    |
  +---------------------------------------------------------------->|
  |                                                                 |
  |   2. UDP(R1(REG_INFO(RELAY_UDP_HIP,[RELAY_UDP_ESP])))           |
  |<----------------------------------------------------------------+
  |                                                                 |
  |   3. UDP(I2(REG_REQ(RELAY_UDP_HIP),[RELAY_UDP_ESP]))            |
  +---------------------------------------------------------------->|
  |                                                                 |
  |   4. UDP(R2(REG_RES(RELAY_UDP_HIP,[RELAY_UDP_ESP]), REG_FROM,   |
  |          [RELAYED_ADDRESS]))                                    |
  |<----------------------------------------------------------------+
  |                                                                 |

          

Figure 2: Example Registration with a HIP Relay

In step 1, the Relay Client (Initiator) starts the registration procedure by sending an I1 packet over UDP to the Relay Server. It is RECOMMENDED that the Relay Client select a random port number from the ephemeral port range 49152-65535 for initiating a base exchange. Alternatively, a host MAY also use a single fixed port for initiating all outgoing connections. However, the allocated port MUST be maintained until all of the corresponding HIP Associations are closed. It is RECOMMENDED that the Relay Server listen to incoming connections at UDP port 10500. If some other port number is used, it needs to be known by potential Relay Clients.

In step 2, the Relay Server (Responder) lists the services that it supports in the R1 packet. The support for HIP control plane over UDP relaying is denoted by the Registration Type value RELAY_UDP_HIP (see Section 5.9). If the server supports also relaying of ESP traffic over UDP, it includes also Registration type value RELAY_UDP_ESP.

In step 3, the Relay Client selects the services for which it registers and lists them in the REG_REQ parameter. The Relay Client registers for the Control Data Relay service by listing the RELAY_UDP_HIP value in the request parameter. If the Relay Client requires also ESP relaying over UDP, it lists also RELAY_UDP_ESP.

In step 4, the Relay Server concludes the registration procedure with an R2 packet and acknowledges the registered services in the REG_RES parameter. The Relay Server denotes unsuccessful registrations (if any) in the REG_FAILED parameter of R2. The Relay Server also includes a REG_FROM parameter that contains the transport address of the Relay Client as observed by the Relay Server (Server Reflexive candidate). If the Relay Client registered to ESP relaying service, the Relay Server includes RELAYED_ADDRESS parameter that describes the UDP port allocated to the Relay Client for ESP relaying. It is worth noting that the Data Relay Client must first activate this UDP port by sending an UPDATE message to the Data Relay Server that includes a PEER_PERMISSION parameter as described in Section 4.12.1 both after base exchange and handover procedures. Also, the Data Relay Server should follow the port allocation recommendations in Section 6.5.

After the registration, the Relay Client sends periodically NAT keepalives to the Relay Server in order to keep the NAT bindings between the Relay Client and the relay alive. The keepalive extensions are described in Section 4.10.

The Data Relay Client MUST maintain an active HIP association with the Data Relay Server as long as it requires the data relaying service. When the HIP association is closed (or times out), or the registration lifetime passes without the Data Relay Client refreshing the registration, the Data Relay Server MUST stop relaying packets for that host and close the corresponding UDP port (unless other Data Relay Clients are still using it).

The Data Relay Server MAY use the same relayed address and port for multiple Data Relay Clients, but since this can cause problems with stateful firewalls (see Section 6.5) it is NOT RECOMMENDED.

When a Control Relay Client sends an UPDATE (e.g., due to host movement or to renew service registration), the Control Relay Server MUST follow the general guidelines defined in [RFC8003], with the difference that all UPDATE messages are delivered on top of UDP. In addition to this, the Control Relay Server MUST include the REG_FROM parameter in all UPDATE responses sent to the Control Relay Client. This applies both renewals of service registration but also to host movement, where especially the latter requires the Control Relay Client to learn its new server reflexive address candidate.

4.2. Transport Address Candidate Gathering at the Relay Client

An Initiator needs to gather a set of address candidates before contacting a (non-relay) Responder. The candidates are needed for connectivity checks that allow two hosts to discover a direct, non-relayed path for communicating with each other. One server reflexive candidate can be discovered during the registration with the Control Relay Server from the REG_FROM parameter (and another from Data Relay Server if one is employed).

The candidate gathering can be done at any time, but it needs to be done before sending an I2 or R2 in the base exchange if ICE-HIP-UDP mode is to be used for the connectivity checks. It is RECOMMENDED that all three types of candidates (host, server reflexive, and relayed) are gathered to maximize the probability of successful NAT traversal. However, if no Data Relay Server is used, and the host has only a single local IP address to use, the host MAY use the local address as the only host candidate and the address from the REG_FROM parameter discovered during the Control Relay Server registration as a server reflexive candidate. In this case, no further candidate gathering is needed.

If a Relay Client has more than one network interface, it can discover additional server reflexive candidates by sending UPDATE messages from each of its interfaces to the Relay Server. Each such UPDATE message MUST include the following parameters: registration request (REG_REQ) parameter with Registration Type CANDIDATE_DISCOVERY (value [TBD by IANA: 4]) and ECHO_REQUEST_SIGN parameter. When a Control Relay Server receives an UPDATE message with registration request containing a CANDIDATE_DISCOVERY type, it MUST include a REG_FROM parameter, containing the same information as if this were a Control Relay Server registration, to the response (in addition to the mandatory ECHO_RESPONSE_SIGNED paramater). This request type SHOULD NOT create any state at the Control Relay Server.

ICE guidelines [I-D.ietf-ice-rfc5245bis] for candidate gathering are followed here. A number of host candidates (loopback, anycast and others) should be excluded as described in the ICE specification [I-D.ietf-ice-rfc5245bis]. Relayed candidates SHOULD be gathered in order to guarantee successful NAT traversal, and implementations SHOULD support this functionality even if it will not be used in deployments in order to enable it by software configuration update if needed at some point. A host SHOULD employ only a single server for gathering the candidates for a single HIP association; either a one server providing both Control and Data Relay Server functionality, or one Control Relay Server and also Data Relay Server if the functionality is offered by another server. When the relay service is split between two hosts, the server reflexive candidate from the Control Relay Server SHOULD be used instead of the one provided by the Data Relay Server. If a relayed candidate is identical to a host candidate, the relayed candidate must be discarded. NAT64 considerations in [I-D.ietf-ice-rfc5245bis] apply as well.

HIP based connectivity can be utilized by IPv4 applications using LSIs and by IPv6 based applications using HITs. The LSIs and HITs of the local virtual interfaces MUST be excluded in the candidate gathering phase as well to avoid creating unnecessary loopback connectivity tests.

Gathering of candidates MAY also be performed by other means than described in this section. For example, the candidates could be gathered as specified in Section 4.2 of [RFC5770] if STUN servers are available, or if the host has just a single interface and no STUN or Data Relay Server are available.

Each local address candidate MUST be assigned a priority. The following recommended formula (as described in [I-D.ietf-ice-rfc5245bis]) SHOULD be used:

In the formula, type preference follows the ICE specification section 4.1.2.2 guidelines: the RECOMMENDED values are 126 for host candidates, 100 for server reflexive candidates, 110 for peer reflexive candidates, and 0 for relayed candidates. The highest value is 126 (the most preferred) and lowest is 0 (last resort). For all candidates of the same type, the preference type value MUST be identical, and, correspondingly, the value MUST be different for different types. For peer reflexive values, the type preference value MUST be higher than for server reflexive types. It should be noted that peer reflexive values are learned later during connectivity checks, so a host cannot employ it during candidate gathering stage yet.

Following the ICE specification, the local preference MUST be an integer from 0 (lowest preference) to 65535 (highest preference) inclusive. In the case the host has only a single address candidate, the value SHOULD be 65535. In the case of multiple candidates, each local preference value MUST be unique. Dual-stack considerations for IPv6 in ICE apply also here.

Unlike ICE, this protocol only creates a single UDP flow between the two communicating hosts, so only a single component exists. Hence, the component ID value MUST always be set to 1.

As defined in ICE , the retransmission timeout (RTO) for address gathering from a Control/Data Relay Server SHOULD be calculated as follows:

where Ta is the value used for Ta is the value used for the connectivity check pacing and Num-Of-Pairs is number of pairs of candidates with Control and Data Relay Servers (e.g. in the case of a single server, it would be 1). A smaller value than 500 ms for the RTO MUST NOT be used.

4.3. NAT Traversal Mode Negotiation

This section describes the usage of a new non-critical parameter type. The presence of the parameter in a HIP base exchange means that the end-host supports NAT traversal extensions described in this document. As the parameter is non-critical (as defined in Section 5.2.1 of [RFC7401]), it can be ignored by a end-host, which means that the host is not required to support it or may decline to use it.

With registration with a Control/Data Relay Server, it is usually sufficient to use the UDP-ENCAPSULATION mode of NAT traversal since the Relay Server is assumed to be in public address space. Thus, the Relay Server SHOULD propose the UDP-ENCAPSULATION mode as the preferred or only mode. The NAT traversal mode negotiation in a HIP base exchange is illustrated in Figure 3. It is worth noting that the Relay Server could be located between the hosts, but is omitted here for simplicity.

Initiator                                                Responder
| 1. UDP(I1)                                                     |
+--------------------------------------------------------------->|
|                                                                |
| 2. UDP(R1(.., NAT_TRAVERSAL_MODE(ICE-HIP-UDP), ..))            |
|<---------------------------------------------------------------+
|                                                                |
| 3. UDP(I2(.., NAT_TRAVERSAL_MODE(ICE-HIP-UDP), LOC_SET, ..))   |
+--------------------------------------------------------------->|
|                                                                |
| 4. UDP(R2(.., LOC_SET, ..))                                    |
|<---------------------------------------------------------------+
|                                                                |

          

Figure 3: Negotiation of NAT Traversal Mode

In step 1, the Initiator sends an I1 to the Responder. In step 2, the Responder responds with an R1. As specified in [RFC5770], the NAT_TRAVERSAL_MODE parameter in R1 contains a list of NAT traversal modes the Responder supports. The mode specified in this document is ICE-HIP-UDP (value [TBD by IANA: 3]).

In step 3, the Initiator sends an I2 that includes a NAT_TRAVERSAL_MODE parameter. It contains the mode selected by the Initiator from the list of modes offered by the Responder. If ICE-HIP-UDP mode was selected, the I2 also includes the "Transport address" locators (as defined in Section 5.7) of the Initiator in a LOCATOR_SET parameter (denoted here LOC_SET). The locators in I2 are the "ICE offer".

In step 4, the Responder concludes the base exchange with an R2 packet. If the Initiator chose ICE NAT traversal mode, the Responder includes a LOCATOR_SET parameter in the R2 packet. The locators in R2, encoded like the locators in I2, are the "ICE answer". If the NAT traversal mode selected by the Initiator is not supported by the Responder, the Responder SHOULD reply with a NOTIFY packet with type NO_VALID_NAT_TRAVERSAL_MODE_PARAMETER and abort the base exchange.

4.4. Connectivity Check Pacing Negotiation

As explained in Legacy ICE-HIP [RFC5770], when a NAT traversal mode with connectivity checks is used, new transactions should not be started too fast to avoid congestion and overwhelming the NATs. For this purpose, during the base exchange, hosts can negotiate a transaction pacing value, Ta, using a TRANSACTION_PACING parameter in R1 and I2 packets. The parameter contains the minimum time (expressed in milliseconds) the host would wait between two NAT traversal transactions, such as starting a new connectivity check or retrying a previous check. The value that is used by both of the hosts is the higher of the two offered values.

The minimum Ta value SHOULD be configurable, and if no value is configured, a value of 50 ms MUST be used. Guidelines for selecting a Ta value are given in Appendix A. Hosts SHOULD NOT use values smaller than 5 ms for the minimum Ta, since such values may not work well with some NATs (as explained in [I-D.ietf-ice-rfc5245bis]). The Initiator MUST NOT propose a smaller value than what the Responder offered. If a host does not include the TRANSACTION_PACING parameter in the base exchange, a Ta value of 50 ms MUST be used as that host's minimum value.

4.5. Base Exchange via Control Relay Server

This section describes how the Initiator and Responder perform a base exchange through a Control Relay Server. Connectivity pacing (denoted as TA_P here) was described in Section 4.4 and is neither repeated here. Similarly, the NAT traversal mode negotiation process (denoted as NAT_TM in the example) was described in Section 4.3 and is neither repeated here. If a Control Relay Server receives an R1 or I2 packet without the NAT traversal mode parameter, it MUST drop it and SHOULD send a NOTIFY error packet with type NO_VALID_NAT_TRAVERSAL_MODE_PARAMETER to the sender of the R1 or I2.

It is RECOMMENDED that the Initiator send an I1 packet encapsulated in UDP when it is destined to an IPv4 address of the Responder. Respectively, the Responder MUST respond to such an I1 packet with a UDP-encapsulated R1 packet, and also the rest of the communication related to the HIP association MUST also use UDP encapsulation.

Figure 4 illustrates a base exchange via a Control Relay Server. We assume that the Responder (i.e. a Control Relay Client) has already registered to the Control Relay Server. The Initiator may have also registered to another (or the same Control Relay Server), but the base exchange will traverse always through the Control Relay Server of the Responder.

Initiator                  Control Relay Server             Responder
| 1. UDP(I1)                       |                                |
+--------------------------------->| 2. UDP(I1(RELAY_FROM))         |
|                                  +------------------------------->|
|                                  |                                |
|                                  | 3. UDP(R1(RELAY_TO, NAT_TM,    |
|                                  |        TA_P))                  |
| 4. UDP(R1(RELAY_TO, NAT_TM,      |<-------------------------------+
|        TA_P))                    |                                |
|<---------------------------------+                                |
|                                  |                                |
| 5. UDP(I2(LOC_SET, NAT_TM,       |                                |
|        TA_P))                    |                                |
+--------------------------------->| 6. UDP(I2(LOC_SET, RELAY_FROM, |
|                                  |           NAT_TM, TA_P))       |
|                                  +------------------------------->|
|                                  |                                |
|                                  | 7. UDP(R2(LOC_SET, RELAY_TO))  |
| 8. UDP(R2(LOC_SET, RELAY_TO))    |<-------------------------------+
|<---------------------------------+                                |
|                                  |                                |

          

Figure 4: Base Exchange via a HIP Relay Server

In step 1 of Figure 4, the Initiator sends an I1 packet over UDP via the Control Relay Server to the Responder. In the HIP header, the source HIT belongs to the Initiator and the destination HIT to the Responder. The initiator sends the I1 packet from its IP address to the IP address of the Control Relay Server over UDP.

In step 2, the Control Relay Server receives the I1 packet. If the destination HIT belongs to a registered Responder, the Control Relay Server processes the packet. Otherwise, the Control Relay Server MUST drop the packet silently. The Control Relay Server appends a RELAY_FROM parameter to the I1 packet, which contains the transport source address and port of the I1 as observed by the Control Relay Server. The Control Relay Server protects the I1 packet with RELAY_HMAC as described in [RFC8004], except that the parameter type is different (see Section 5.8). The Control Relay Server changes the source and destination ports and IP addresses of the packet to match the values the Responder used when registering to the Control Relay Server, i.e., the reverse of the R2 used in the registration. The Control Relay Server MUST recalculate the transport checksum and forward the packet to the Responder.

In step 3, the Responder receives the I1 packet. The Responder processes it according to the rules in [RFC7401]. In addition, the Responder validates the RELAY_HMAC according to [RFC8004] and silently drops the packet if the validation fails. The Responder replies with an R1 packet to which it includes RELAY_TO and NAT traversal mode parameters. The responder MUST include ICE-HIP-UDP in the NAT traversal modes. The RELAY_TO parameter MUST contain the same information as the RELAY_FROM parameter, i.e., the Initiator's transport address, but the type of the parameter is different. The RELAY_TO parameter is not integrity protected by the signature of the R1 to allow pre-created R1 packets at the Responder.

In step 4, the Control Relay Server receives the R1 packet. The Control Relay Server drops the packet silently if the source HIT belongs to a Control Relay Client that has not successfully registered. The Control Relay Server MAY verify the signature of the R1 packet and drop it if the signature is invalid. Otherwise, the Control Relay Server rewrites the source address and port, and changes the destination address and port to match RELAY_TO information. Finally, the Control Relay Server recalculates transport checksum and forwards the packet.

In step 5, the Initiator receives the R1 packet and processes it according to [RFC7401]. The Initiator MAY use the address in the RELAY_TO parameter as a local peer-reflexive candidate for this HIP association if it is different from all known local candidates. The Initiator replies with an I2 packet that uses the destination transport address of R1 as the source address and port. The I2 packet contains a LOCATOR_SET parameter that lists all the HIP candidates (ICE offer) of the Initiator. The candidates are encoded using the format defined in Section 5.7. The I2 packet MUST also contain a NAT traversal mode parameter that includes ICE-HIP-UDP mode.

In step 6, the Control Relay Server receives the I2 packet. The Control Relay Server appends a RELAY_FROM and a RELAY_HMAC to the I2 packet similarly as explained in step 2, and forwards the packet to the Responder.

In step 7, the Responder receives the I2 packet and processes it according to [RFC7401]. It replies with an R2 packet and includes a RELAY_TO parameter as explained in step 3. The R2 packet includes a LOCATOR_SET parameter that lists all the HIP candidates (ICE answer) of the Responder. The RELAY_TO parameter is protected by the HMAC.

In step 8, the Control Relay Server processes the R2 as described in step 4. The Control Relay Server forwards the packet to the Initiator. After the Initiator has received the R2 and processed it successfully, the base exchange is completed.

Hosts MUST include the address of one or more Control Relay Servers (including the one that is being used for the initial signaling) in the LOCATOR_SET parameter in I2 and R2 if they intend to use such servers for relaying HIP signaling immediately after the base exchange completes. The traffic type of these addresses MUST be "HIP signaling" and they MUST NOT be used as HIP candidates. If the Control Relay Server locator used for relaying the base exchange is not included in I2 or R2 LOCATOR_SET parameters, it SHOULD NOT be used after the base exchange. Instead, further HIP signaling SHOULD use the same path as the data traffic. It is RECOMMENDED to use the same Control Relay Server throughout the lifetime of the host association that was used for forwarding the base exchange if the Responder includes it in the locator parameter of the R2 message.

4.6. Connectivity Checks

When the Initiator and Responder complete the base exchange through the Control Relay Server, both of them employ the IP address of the Control Relay Server as the destination address for the packets. This address MUST NOT be used as a destination for ESP traffic (i.e., the corresponding Control Relay Client cannot advertise it to its peer) unless the server supports also Data Relay Server functionality, for which the client has successfully registered to. When NAT traversal mode with ICE-HIP-UDP was successfully negotiated and selected, the Initiator and Responder MUST start the connectivity checks in order to attempt to obtain direct end-to-end connectivity through NAT devices. It is worth noting that the connectivity checks MUST be completed even though no ESP_TRANSFORM would be negotiated and selected.

The connectivity checks follow the ICE methodology [MMUSIC-ICE], but UDP encapsulated HIP control messages are used instead of ICE messages. Only normal nomination MUST be used for the connectivity checks, i.e., aggressive nomination MUST NOT be employed. As stated in the ICE specification, the basic procedure for connectivity checks has three phases: sorting the candidate pairs according their priority, sending checks in the prioritized order and acknowledging the checks from the peer host.

The Initiator MUST take the role of controlling host and the Responder acts as the controlled host. The roles MUST persist throughout the HIP associate lifetime (to be reused in the possibly mobility UPDATE procedures). In the case both communicating nodes are initiating the communications to each other using an I1 packet, the conflict is resolved as defined in section 6.7 in [RFC7401]: the host with the "larger" HIT changes to its Role to Responder. In such a case, the host changing its role to Responder MUST also switch to controlling role.

The protocol follows standard HIP UPDATE sending and processing rules as defined in section 6.11 and 6.12 in [RFC7401], but some new parameters are introduced (CANDIDATE_PRIORITY, MAPPED_ADDRESS and NOMINATE).

4.6.1. Connectivity Check Procedure

Figure 5 illustrates connectivity checks in a simplified scenario, where the Initiator and Responder have only a single candidate pair to check. Typically, NATs drop messages until both sides have sent messages using the same port pair. In this scenario, the Responder sends a connectivity check first but the NAT of the Initiator drops it. However, the connectivity check from the Initiator reaches the Responder because it uses the same port pair as the first message. It is worth noting that the message flow in this section is idealistic, and, in practice, more messages would be dropped, especially in the beginning. For instance, connectivity tests always start with the candidates with the highest priority, which would be host candidates (which would not reach the recipient in this scenario).

Initiator  NAT1                                 NAT2        Responder
|             | 1. UDP(UPDATE(SEQ, CAND_PRIO,      |                |
|             |        ECHO_REQ_SIGN))             |                |
|             X<-----------------------------------+----------------+
|             |                                    |                |
| 2. UDP(UPDATE(SEQ, ECHO_REQ_SIGN, CAND_PRIO))    |                |
+-------------+------------------------------------+--------------->|
|             |                                    |                |
| 3. UDP(UPDATE(ACK, ECHO_RESP_SIGN, MAPPED_ADDR)) |                |
|<------------+------------------------------------+----------------+
|             |                                    |                |
| 4. UDP(UPDATE(SEQ, ECHO_REQ_SIGN, CAND_PRIO))    |                |
|<------------+------------------------------------+----------------+
|             |                                    |                |
| 5. UDP(UPDATE(ACK, ECHO_RESP_SIGN, MAPPED_ADDR)) |                |
+-------------+------------------------------------+--------------->|
|             |                                    |                |
| 6. Other connectivity checks using UPDATE over UDP                |
|<------------+------------------------------------+---------------->
|             |                                    |                |
| 7. UDP(UPDATE(SEQ, ECHO_REQ_SIGN, CAND_PRIO, NOMINATE))           |
+-------------+------------------------------------+--------------->|
|             |                                    |                |
| 8. UDP(UPDATE(SEQ, ACK, ECHO_REQ_SIGN, ECHO_RESP_SIGN,            |
|           NOMINATE))                             |                |
|<------------+------------------------------------+----------------+
|             |                                    |                |
| 9. UDP(UPDATE(ACK, ECHO_RESP_SIGN))              |                |
+-------------+------------------------------------+--------------->+
|             |                                    |                |
| 10. ESP data traffic over UDP                     |               |
+<------------+------------------------------------+--------------->+
|             |                                    |                |

            

Figure 5: Connectivity Checks

In step 1, the Responder sends a connectivity check to the Initiator that the NAT of the Initiator drops. The message includes a number of parameters. As specified in [RFC7401]), the SEQ parameter includes a running sequence identifier for the connectivity check. The candidate priority (denoted "CAND_PRIO" in the figure) describes the priority of the address candidate being tested. The ECHO_REQUEST_SIGNED (denoted ECHO_REQ_SIGN in the figure) includes a nonce that the recipient must sign and echo back as it is.

In step 2, the Initiator sends a connectivity check, using the same address pair candidate as in the previous step, and the message traverses successfully the NAT boxes. The message includes the same parameters as in the previous step. It should be noted that the sequence identifier is locally assigned by the Responder, so it can be different than in the previous step.

In step 3, the Responder has successfully received the previous connectivity check from the Initiator and starts to build a response message. Since the message from the Initiator included a SEQ, the Responder must acknowledge it using an ACK parameter. Also, the nonce contained in the echo request must be echoed back in an ECHO_REQUEST_SIGNED (denoted ECHO_REQUEST_SIGN) parameter. The Responder includes also a MAPPED_ADDRESS parameter (denoted MAPPED_ADDR in the figure) that contains the transport address of the Initiator as observed by the Responder (i.e. peer reflexive candidate). This message is successfully delivered to the Initiator, and upon reception the Initiator marks the candidate pair as valid.

In step 4, the Responder retransmits the connectivity check sent in the first step, since it was not acknowledged yet.

In step 5, the Initiator responds to the previous connectivity check message from the Responder. The Initiator acknowledges the SEQ parameter from the previous message using ACK parameter and the ECHO_REQUEST_SIGN parameter with ECHO_RESPONSE_SIGNED. In addition, it includes MAPPED_ADDR parameter that includes the peer reflexive candidate. This response message is successfully delivered to the Responder, and upon reception the Initiator marks the candidate pair as valid.

In step 6, despite the two hosts now having valid address candidates, the hosts still test the remaining address candidates in a similar way as in the previous steps (due to the use of normal nomination). It should be noted that each connectivity check has a unique sequence number in the SEQ parameter.

In step 7, the Initiator has completed testing all address candidates and nominates one address candidate to be used. It sends an UPDATE message using the selected address candidates that includes a number of parameters: SEQ, ECHO_REQUEST_SIGN, CANDIDATE_PRIORITY and the NOMINATE parameter.

In step 8, the Responder receives the message with NOMINATE parameter from the Initiator. It sends a response that includes the NOMINATE parameter in addition to a number of other parameters. The ACK and ECHO_RESPONSE_SIGNED parameters acknowledge the SEQ and ECHO_REQUEST_SIGN parameters from previous message from the Initiator. The Responder includes SEQ and ECHO_REQUEST_SIGN parameters in order to receive an acknowledgment from the Responder.

In step 9, the Initiator completes the candidate nomination process by confirming the message reception to the Responder. In the confirmation message, the ACK and ECHO_RESPONSE_SIGNED parameters correspond to the SEQ and ECHO_REQUEST_SIGN parameters in the message sent by the Responder in the previous step.

In step 10, the Initiator and Responder can start sending application payload over the successfully nominated address candidates.

It is worth noting that if either host has registered a relayed address candidate from a Data Relay Server, the host MUST activate the address before connectivity checks by sending an UPDATE message containing PEER_PERMISSION parameter as described in Section 4.12.1. Otherwise, the Data Relay Server drops ESP packets using the relayed address.

It should be noted that in the case both Initiator and Responder both advertising their own relayed address candidates, it is possible that the two hosts choose the two relayed addresses as a result of the ICE nomination algorithm. While this is possible (and even could be desirable for privacy reasons), it can be unlikely due to low priority assigned for the relayed address candidates. In such a event, the nominated address pair is always symmetric; the nomination algorithm prevents asymmetric address pairs (i.e. each side choosing different pair), such as a Data Relay Client using its own Data Relay Server to send data directly to its peer while receiving data from the Data Relay Server of its peer.

4.6.2. Rules for Connectivity Checks

The HITs of the two communicating hosts MUST be used as credentials in this protocol (in contrast to ICE which employs username-password fragments). A HIT pair uniquely identifies the corresponding HIT association, and a SEQ number in an UPDATE message identifies a particular connectivity check.

All of the connectivity check packets MUST be protected with HMACs and signatures (even though the illustrations in this specification omit them for simplicity). Each connectivity check sent by a host MUST include a SEQ parameter and ECHO_REQUEST_SIGN parameter, and correspondingly the peer MUST respond to these using ACK and ECHO_RESPONSE_SIGNED according to the rules specified in [RFC7401].

The host sending a connectivity check MUST validate that the response uses the same pair of UDP ports, and drop the packet if this is not the case.

A host may receive a connectivity check before it has received the candidates from its peer. In such a case, the host MUST immediately generate a response, and then continue waiting for the candidates. A host MUST NOT select a candidate pair until it has verified the pair using a connectivity check as defined in section Section 4.6.1.

[RFC7401] states that UPDATE packets have to include either a SEQ or ACK parameter (or both). According to the RFC, each SEQ parameter should be acknowledged separately. In the context of NATs, this means that some of the SEQ parameters sent in connectivity checks will be lost or arrive out of order. From the viewpoint of the recipient, this is not a problem since the recipient will just "blindly" acknowledge the SEQ. However, the sender needs to be prepared for lost sequence identifiers and ACKs parameters that arrive out of order.

As specified in [RFC7401], an ACK parameter may acknowledge multiple sequence identifiers. While the examples in the previous sections do not illustrate such functionality, it is also permitted when employing ICE-HIP-UDP mode.

In ICE-HIP-UDP mode, a retransmission of a connectivity check SHOULD be sent with the same sequence identifier in the SEQ parameter. Some tested address candidates will never produce a working address pair, and thus may cause retransmissions. Upon successful nomination an address pair, a host MAY immediately stop sending such retransmissions.

ICE procedures for prioritizing candidates, eliminating redundant candidates and forming check lists (including pruning) must be followed (as specified in [I-D.ietf-ice-rfc5245bis]), with the exception that the foundation, frozen candidates and default candidates are not used. From viewpoint of the ICE specification [I-D.ietf-ice-rfc5245bis], the protocol specified in this document operates using Component ID of 1 on all candidates, and the foundation of all candidates is unique. This specification defines only "full ICE" mode, and the "lite ICE" is not supported. The reasoning behind the missing features is described in Appendix B.

The connectivity check messages MUST be paced by the Ta value negotiated during the base exchange as described in Section 4.4. If neither one of the hosts announced a minimum pacing value, a value of 20 ms SHOULD be used.

Both hosts MUST form a priority ordered checklist and begin to check transactions every Ta milliseconds as long as the checks are running and there are candidate pairs whose tests have not started. The retransmission timeout (RTO) for the connectivity check UPDATE packets SHOULD be calculated as follows:

In the RTO formula, Ta is the value used for the connectivity check pacing, Num-Waiting is the number of pairs in the checklist in the "Waiting" state, and Num-In-Progress is the number of pairs in the "In-Progress" state. This is identical to the formula in [I-D.ietf-ice-rfc5245bis] when there is only one checklist. A smaller value than 500 ms for the RTO MUST NOT be used.

Each connectivity check request packet MUST contain a CANDIDATE_PRIORITY parameter (see Section 5.14) with the priority value that would be assigned to a peer reflexive candidate if one was learned from the corresponding check. An UPDATE packet that acknowledges a connectivity check request MUST be sent from the same address that received the check and delivered to the same address where the check was received from. Each acknowledgment UPDATE packet MUST contain a MAPPED_ADDRESS parameter with the port, protocol, and IP address of the address where the connectivity check request was received from.

Following the ICE guidelines [I-D.ietf-ice-rfc5245bis], it is RECOMMENDED to restrict the total number of connectivity checks to 100 for each host association. This can be achieved by limiting the connectivity checks to the 100 candidate pairs with the highest priority.

4.6.3. Rules for Concluding Connectivity Checks

The controlling agent may find multiple working candidate pairs. To conclude the connectivity checks, it SHOULD nominate the pair with the highest priority. The controlling agent MUST nominate a candidate pair essentially by repeating a connectivity check using an UPDATE message that contains a SEQ parameter (with new sequence number), a ECHO_REQUEST_SIGN parameter, the priority of the candidate in a CANDIDATE_PRIORITY parameter and NOMINATE parameter to signify conclusion of the connectivity checks. Since the nominated address pair has already been tested for reachability, the controlled host should be able to receive the message. Upon reception, the controlled host SHOULD select the nominated address pair. The response message MUST include a SEQ parameter with a new sequence id, acknowledgment of the sequence from the controlling host in an ACK parameter, a new ECHO_REQUEST_SIGNED parameter, ECHO_RESPONSE_SIGNED parameter corresponding to the ECHO_REQUEST_SIGNED parameter from the controlling host and the NOMINATE parameter. After sending this packet, the controlled host can create IPsec security associations using the nominated address candidate for delivering application payload to the controlling host. Since the message from the controlled host included a new sequence id and echo request for signature, the controlling host MUST acknowledge this with a new UPDATE message that includes an ACK and ECHO_RESPONSE_SIGNED parameters. After this final concluding message, the controlling host also can create IPsec security associations for delivering application payload to the controlled host.

It is possible that packets are delayed by the network. Both hosts MUST continue to respond to any connectivity checks despite an address pair having been nominated.

If all the connectivity checks have failed, the hosts MUST NOT send ESP traffic to each other but MAY continue communicating using HIP packets and the locators used for the base exchange. Also, the hosts SHOULD notify each other about the failure with a CONNECTIVITY_CHECKS_FAILED NOTIFY packet (see Section 5.10).

4.7. NAT Traversal Optimizations

4.7.1. Minimal NAT Traversal Support

If the Responder has a fixed and publicly reachable IPv4 address and does not employ a Control Relay Server, the explicit NAT traversal mode negotiation MAY be omitted, and thus even the UDP-ENCAPSULATION mode does not have to be negotiated. In such a scenario, the Initiator sends an I1 message over UDP and the Responder responds with an R1 message over UDP without including any NAT traversal mode parameter. The rest of the base exchange follows the procedures defined in [RFC7401], except that the control and data plane use UDP encapsulation. Here, the use of UDP for NAT traversal is agreed implicitly. This way of operation is still subject to NAT timeouts, and the hosts MUST employ NAT keepalives as defined in Section 4.10.

4.7.2. Base Exchange without Connectivity Checks

It is possible to run a base exchange without any connectivity checks as defined in Legacy ICE-HIP section 4.8 [RFC5770]. The procedure is applicable also in the context of this specification, so it is repeated here for completeness.

In certain network environments, the connectivity checks can be omitted to reduce initial connection set-up latency because a base exchange acts as an implicit connectivity test itself. For this to work, the Initiator MUST be able to reach the Responder by simply UDP encapsulating HIP and ESP packets sent to the Responder's address. Detecting and configuring this particular scenario is prone to failure unless carefully planned.

In such a scenario, the Responder MAY include UDP-ENCAPSULATION NAT traversal mode as one of the supported modes in the R1 packet. If the Responder has registered to a Control Relay Server, it MUST also include a LOCATOR_SET parameter in R1 that contains a preferred address where the Responder is able to receive UDP-encapsulated ESP and HIP packets. This locator MUST be of type "Transport address", its Traffic type MUST be "both", and it MUST have the "Preferred bit" set (see Table 1). If there is no such locator in R1, the source address of R1 is used as the Responder's preferred address.

The Initiator MAY choose the UDP-ENCAPSULATION mode if the Responder listed it in the supported modes and the Initiator does not wish to use the connectivity checks defined in this document for searching for a more optimal path. In this case, the Initiator sends the I2 with UDP-ENCAPSULATION mode in the NAT traversal mode parameter directly to the Responder's preferred address (i.e., to the preferred locator in R1 or to the address where R1 was received from if there was no preferred locator in R1). The Initiator MAY include locators in I2 but they MUST NOT be taken as address candidates, since connectivity checks defined in this document will not be used for connections with UDP-ENCAPSULATION NAT traversal mode. Instead, if R2 and I2 are received and processed successfully, a security association can be created and UDP-encapsulated ESP can be exchanged between the hosts after the base exchange completes. However, the Responder SHOULD NOT send any ESP to the Initiator's address before it has received data from the Initiator, as specified in Sections 4.4.3. and 6.9 of [RFC7401] and in Sections 3.2.9 and 5.4 of [RFC8046].

Since an I2 packet with UDP-ENCAPSULATION NAT traversal mode selected MUST NOT be sent via a Control Relay Server, the Responder SHOULD reject such I2 packets and reply with a NO_VALID_NAT_TRAVERSAL_MODE_PARAMETER NOTIFY packet (see Section 5.10).

If there is no answer for the I2 packet sent directly to the Responder's preferred address, the Initiator MAY send another I2 via the Control Relay Server, but it MUST NOT choose UDP-ENCAPSULATION NAT traversal mode for that I2.

4.7.3. Initiating a Base Exchange both with and without UDP Encapsulation

It is possible to run a base exchange in parallel both with and without UDP encapsulation as defined in Legacy ICE-HIP section 4.9 in [RFC5770]. The procedure is applicable also in the context of this specification, so it is repeated here for completeness.

The Initiator MAY also try to simultaneously perform a base exchange with the Responder without UDP encapsulation. In such a case, the Initiator sends two I1 packets, one without and one with UDP encapsulation, to the Responder. The Initiator MAY wait for a while before sending the other I1. How long to wait and in which order to send the I1 packets can be decided based on local policy. For retransmissions, the procedure is repeated.

The I1 packet without UDP encapsulation may arrive directly, without passing any Control Data Relays, at the Responder. When this happens, the procedures in [RFC7401] are followed for the rest of the base exchange. The Initiator may receive multiple R1 packets, with and without UDP encapsulation, from the Responder. However, after receiving a valid R1 and answering it with an I2, further R1 packets that are not retransmissions of the original R1 message MUST be ignored.

The I1 packet without UDP encapsulation may also arrive at a HIP-capable middlebox. When the middlebox is a HIP rendezvous server and the Responder has successfully registered with the rendezvous service, the middlebox follows rendezvous procedures in [RFC8004].

If the Initiator receives a NAT traversal mode parameter in R1 without UDP encapsulation, the Initiator MAY ignore this parameter and send an I2 without UDP encapsulation and without any selected NAT traversal mode. When the Responder receives the I2 without UDP encapsulation and without NAT traversal mode, it will assume that no NAT traversal mechanism is needed. The packet processing will be done as described in [RFC7401]. The Initiator MAY store the NAT traversal modes for future use, e.g., in case of a mobility or multihoming event that causes NAT traversal to be used during the lifetime of the HIP association.

4.8. Sending Control Packets after the Base Exchange

The same considerations of sending control packets after the base exchange described in legacy ICE-HIP section 5.10 in [RFC5770] apply also here, so they are repeated here for completeness.

After the base exchange, the two end-hosts MAY send HIP control packets directly to each other using the transport address pair established for a data channel without sending the control packets through any Control Relay Servers . When a host does not receive acknowledgments, e.g., to an UPDATE or CLOSE packet after a timeout based on local policies, a host SHOULD resend the packet through the associated Data Relay Server of the peer (if the peer listed it in its LOCATOR_SET parameter in the base exchange.

If Control Relay Client sends a packet through a Control Relay Server, the Control Relay Client MUST always utilize the RELAY_TO parameter. The Control Relay Server SHOULD forward HIP control packets originating from a Control Relay Client to the address denoted in the RELAY_TO parameter. In the other direction, the Control Relay Server SHOULD forward HIP control packets to the Control Relay Clients, and MUST add a RELAY_FROM parameter to the control packets it relays to the Control Relay Clients.

If the Control Relay Server is not willing or able to relay a HIP packet, it MAY notify the sender of the packet with MESSAGE_NOT_RELAYED error notification (see Section 5.10).

4.9. Mobility Handover Procedure

A host may move after base exchange and connectivity checks. Mobility extensions for HIP [RFC8046] define handover procedures without NATs. In this section, we define how two hosts interact with handover procedures in scenarios involving NATs. The specified extensions define only simple mobility using a pair of security associations, and multihoming extensions are left to be defined in later specifications. The procedures in this section offer the same functionality as "ICE restart" specified in [I-D.ietf-ice-rfc5245bis]. The example described in this section shows only a Control Relay Server for the peer host for the sake of simplicity, but also the mobile host may also have a Control Relay Server.

The assumption here is that the two hosts have successfully negotiated and chosen the ICE-HIP-UDP mode during the base exchange as defined in Section 4.3. The Initiator of the base exchange MUST store information that it was the controlling host during the base exchange. Similarly, the Responder MUST store information that it was the controlled host during the base exchange.

Prior to starting the handover procedures with all peer hosts, the mobile host SHOULD first send UPDATE messages to its Control and Data Relay Servers if it has registered to such. It SHOULD wait for all of them to respond for two minutes and then continue with the handover procedure without information from the Relay Server that did not respond. As defined in section Section 4.1, a response message from a Control Relay Server includes a REG_FROM parameter that describes the server reflexive candidate of the mobile host to be used in the candidate exchange during the handover. Similarly, an UPDATE to a Data Relay Server is necessary to make sure the Data Relay Server can forward data to the correct IP address after a handoff.

The mobility extensions for NAT traversal are illustrated in Figure 6. The mobile host is the host that has changed its locators, and the peer host is the host it has a host association with. The mobile host may have multiple peers and it repeats the process with all of its peers. In the figure, the Control Relay Server belongs to the peer host, i.e., the peer host is a Control Relay Client for the Control Relay Server. Next, we describe the procedure in the figure in detail.

Mobile Host               Control Relay Server              Peer Host
| 1. UDP(UPDATE(ESP_INFO,          |                                |
|          LOC_SET, SEQ))          |                                |
+--------------------------------->| 2. UDP(UPDATE(ESP_INFO,        |
|                                  |          LOC_SET, SEQ,         |
|                                  |          RELAY_FROM))          |
|                                  +------------------------------->|
|                                  |                                |
|                                  | 3. UDP(UPDATE(ESP_INFO, ACK,   |
|                                  |          ECHO_REQ_SIGN))       |
| 4. UDP(UPDATE(ESP_INFO, ACK,     |<-------------------------------+
|          ECHO_REQ_SIGN,          |                                |
|          RELAY_TO))              |                                |
|<---------------------------------+                                |
|                                  |                                |
|                   5. connectivity checks over UDP                 |
+<----------------------------------------------------------------->+
|                                  |                                |
|                      6. ESP data over UDP                         |
+<----------------------------------------------------------------->+
|                                  |                                |

          

Figure 6: HIP UPDATE procedure

In step 1, the mobile host has changed location and sends a location update to its peer through the Control Relay Server of the peer. It sends an UPDATE packet with source HIT belonging to itself and destination HIT belonging to the peer host. In the packet, the source IP address belongs to the mobile host and the destination to the Control Relay Server. The packet contains an ESP_INFO parameter, where, in this case, the OLD SPI and NEW SPI parameters both contain the pre-existing incoming SPI. The packet also contains the locators of the mobile host in a LOCATOR_SET parameter. The packet contains also a SEQ number to be acknowledged by the peer. As specified in [RFC8046], the packet may also include a HOST_ID (for middlebox inspection) and DIFFIE_HELLMAN parameter for rekeying.

In step 2, the Control Relay Server receives the UPDATE packet and forwards it to the peer host (i.e. Control Relay Client). The Control Relay Server rewrites the destination IP address and appends a RELAY_FROM parameter to the message.

In step 3, the peer host receives the UPDATE packet, processes it and responds with another UPDATE message. The message is destined to the HIT of mobile host and to the IP address of the Control Relay Server. The message includes an ESP_INFO parameter where, in this case, the OLD SPI and NEW SPI parameters both contain the pre-existing incoming SPI. The peer includes a new SEQ and ECHO_REQUEST_SIGNED parameters to be acknowledged by the mobile host. The message acknowledges the SEQ parameter of the earlier message with an ACK parameter. After this step, the peer host can initiate the connectivity checks.

In step 4, the Control Relay Server receives the message, rewrites the destination IP address, appends an RELAY_TO parameter and forwards the modified message to the mobile host. When mobile host has processed the message successfully, it can initiate the connectivity checks.

In step 5, the two hosts test for connectivity across NATs according to procedures described in Section 4.6. The original Initiator of the communications is the controlling and the original Responder is the controlled host.

In step 6, the connectivity checks are successfully completed and the controlling host has nominated one address pair to be used. The hosts set up security associations to deliver the application payload.

If either host has registered a relayed address candidate from a Data Relay Server, the host MUST reactivate the address before connectivity checks by sending an UPDATE message containing PEER_PERMISSION parameter as described in Section 4.12.1. Otherwise, the Data Relay Server drops ESP packets using the relayed address.

4.10. NAT Keepalives

To prevent NAT states from expiring, communicating hosts send periodic keepalives to other hosts with which they have established a host associating. Both a registered client and Control/Data Relay Server SHOULD send HIP NOTIFY packets to each other every 15 seconds (the so called Tr value in ICE) unless they have exchange some other traffic over the used UDP ports. Other values MAY be used, but a Tr value smaller than 15 seconds MUST NOT be used. The keepalive message encoding format is defined in Section 5.3. If the base exchange or mobility handover procedure occurs during an extremely slow path, a host MAY also send HIP NOTIFY packet every 15 seconds to keep the path active with the recipient.

4.11. Closing Procedure

The two-way procedure for closing a HIP association and the related security associations is defined in [RFC7401]. One host initiates the procedure by sending a CLOSE message and the recipient confirms it with CLOSE_ACK. All packets are protected using HMACs and signatures, and the CLOSE messages includes a ECHO_REQUEST_SIGNED parameter to protect against replay attacks.

The same procedure for closing HIP associations applies also here, but the messaging occurs using the UDP encapsulated tunnel that the two hosts employ. A host sending the CLOSE message SHOULD first send the message over a direct link. After a number of retransmissions, it MUST send over a Control Relay Server of the recipient if one exists. The host receiving the CLOSE message directly without a Control Data Relay SHOULD respond directly. If CLOSE message came via a Control Data Relay, the host SHOULD respond using the same Control Data Relay.

4.12. Relaying Considerations

4.12.1. Forwarding Rules and Permissions

The Data Relay Server uses a similar permission model as a TURN server: before the Data Relay Server forwards any ESP data packets from a peer to a Data Relay Client (or the other direction), the client MUST set a permission for the peer's address. The permissions also install a forwarding rule for each direction, similar to TURN's channels, based on the Security Parameter Index (SPI) values in the ESP packets.

Permissions are not required for HIP control packets. However, if a relayed address (as conveyed in the RELAYED_ADDRESS parameter from the Data Relay Server) is selected to be used for data, the Control Relay Client MUST send an UPDATE message to the Data Relay Server containing a PEER_PERMISSION parameter (see Section 5.13) with the address of the peer, and the outbound and inbound SPI values the Control Relay Client is using with this particular peer. To avoid packet dropping of ESP packets, the Control Relay Client SHOULD send the PEER_PERMISSION parameter before connectivity checks both in the case of base exchange and a mobility handover. It is worth noting that the UPDATE message includes a SEQ parameter (as specified in [RFC7401]) that the Data Relay Server must acknowledge, so that the Control Relay Client can resend the message with PEER_PERMISSION parameter if it gets lost.

When a Data Relay Server receives an UPDATE with a PEER_PERMISSION parameter, it MUST check if the sender of the UPDATE is registered for data relaying service, and drop the UPDATE if the host was not registered. If the host was registered, the Data Relay Server checks if there is a permission with matching information (address, protocol, port and SPI values). If there is no such permission, a new permission MUST be created and its lifetime MUST be set to 5 minutes. If an identical permission already existed, it MUST be refreshed by setting the lifetime to 5 minutes. A Data Relay Client SHOULD refresh permissions 1 minute before the expiration when the permission is still needed.

When a Data Relay Server receives an UPDATE from a registered client but without a PEER_PERMISSION parameter and with a new locator set, the Data Relay Server can assume that the mobile host has changed its location and, thus, is not reachable in its previous location. In such an event, the Data Relay Server SHOULD deactivate the permission and stop relaying data plane traffic to the client.

The relayed address MUST be activated with the PEER_PERMISSION parameter both after a base exchange and after a handover procedure with another ICE-HIP-UDP capable host. Unless activated, the Data Relay Server MUST drop all ESP packets. It is worth noting that a Data Relay Client does not have to renew its registration upon a change of location UPDATE, but only when the lifetime of the registration is close to end.

4.12.2. HIP Data Relay and Relaying of Control Packets

When a Data Relay Server accepts to relay UDP encapsulated ESP between a Data Relay Client and its peer, the Data Relay Server opens a UDP port (relayed address) for this purpose as described in Section 4.1. This port can be used for delivering also control packets because connectivity checks also cover the path through the Data Relay Server. If the Data Relay Server receives a UDP encapsulated HIP control packet on that port, it MUST forward the packet to the Data Relay Client and add a RELAY_FROM parameter to the packet as if the Data Relay Server were acting as a Control Relay Server. When the Data Relay Client replies to a control packet with a RELAY_FROM parameter via its Data Relay Server, the Data Relay Client MUST add a RELAY_TO parameter containing the peer's address and use the address of its Data Relay Server as the destination address. Further, the Data Relay Server MUST send this packet to the peer's address from the relayed address.

If the Data Relay Server receives a UDP packet that is not a HIP control packet to the relayed address, it MUST check if it has a permission set for the peer the packet is arriving from (i.e., the sender's address and SPI value matches to an installed permission). If permissions are set, the Data Relay Server MUST forward the packet to the Data Relay Client that created the permission. The Data Relay Server MUST also implement the similar checks for the reverse direction (i.e. ESP packets from the Data Relay Client to the peer). Packets without a permission MUST be dropped silently.

4.12.3. Handling Conflicting SPI Values

Since a Data Relay Server may have to deal with multiple Relay Clients and their peers, such a Relay may experience collisions in the SPI namespace. Two problematic cases are described in this section.

In the first scenario, an SPI collision may occur when two Initiators run a base exchange to the same Responder (i.e. Data Relay Client), and both the Initiators claim the same inbound SPI at the Data Relay Server using PEER_PERMISSION Parameter. In this case, the Data Relay Server cannot disambiguate the correct destination of an ESP packet originating from the Data Relay Client because the SPI could belong to either of the peers (and destination IP and UDP port belonging to the Data Relay Server are not unique either). The problem can be mitigated at the Data Relay Clients (i.e. Responder). Upon receiving an I2 with a colliding SPI, the Responder MUST NOT include the relayed address candidate in the R2 message because the Data Relay Server would not be able demultiplex the related ESP packet to the correct Initiator. The same applies also the handover procedures; the Data Relay Client MUST NOT include the relayed address candidate when sending its new locator set in an UPDATE to its peer if it would cause a SPI conflict with another peer. Since the SPI space is 32 bits and the SPI values should be random, the probability for a conflicting SPI value is fairly small. However, a Data Relay Client with many peers MAY proactively decrease the odds of a conflict by registering to multiple Data Relay Servers. Thus, the described collision scenario can be avoided if the Responder delivers a new relayed address candidate upon SPI collisions. Each relayed address has a separate UDP port reserved to it, so collision problem does not occur.

In the second scenario, the SPI collision problems occurs if two hosts have registered to the same Data Relay Server and a third host initiates base exchange with both of them. Here, the two Responders (i.e. Data Relay Clients) claim the same inbound SPI number with the same Initiator (peer). However, in this case, the Data Relay Server has allocated separate UDP ports for the two Data Relay Clients acting now as Responders (as recommended in Section 6.5). When the peer sends an ESP packet, the Data Relay Server is able to forward the packet to the correct Data Relay Client because the destination UDP port for each of the clients.

5. Packet Formats

The following subsections define the parameter and packet encodings for the HIP and ESP packets. All values MUST be in network byte order.

It is worth noting that most of the parameters are shown for the sake of completeness even though they are specified already in Legacy ICE-HIP [RFC5770]. New parameters are explicitly described as new.

5.1. HIP Control Packets

Figure 7 illustrates the packet format for UDP-encapsulated HIP. The format is identical to Legacy ICE-HIP [RFC5770].

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|        Source Port            |       Destination Port        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           Length              |           Checksum            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       32 bits of zeroes                       |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
~                    HIP Header and Parameters                  ~
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                

Figure 7: Format of UDP-Encapsulated HIP Control Packets

HIP control packets are encapsulated in UDP packets as defined in Section 2.2 of [RFC3948], "IKE Header Format for Port 4500", except that a different port number is used. Figure 7 illustrates the encapsulation. The UDP header is followed by 32 zero bits that can be used to differentiate HIP control packets from ESP packets. The HIP header and parameters follow the conventions of [RFC7401] with the exception that the HIP header checksum MUST be zero. The HIP header checksum is zero for two reasons. First, the UDP header already contains a checksum. Second, the checksum definition in [RFC7401] includes the IP addresses in the checksum calculation. The NATs that are unaware of HIP cannot recompute the HIP checksum after changing IP addresses.

A Control/Data Relay Server or a non-relay Responder SHOULD listen at UDP port 10500 for incoming UDP-encapsulated HIP control packets. If some other port number is used, it needs to be known by potential Initiators.

5.2. Connectivity Checks

HIP connectivity checks are HIP UPDATE packets. The format is specified in [RFC7401].

5.3. Keepalives

The RECOMMENDED encoding format for keepalives is HIP NOTIFY packets as specified in [RFC7401] with Notify message type field set to NAT_KEEPALIVE [TBD by IANA: 16385] and with an empty Notification data field. It is worth noting that sending of such a HIP NOTIFY message MAY be omitted if the host is actively (or passively) sending other traffic to the peer host over the UDP tunnel associate with the host association (and IPsec security associations since the same port pair is reused) during the Tr period. For instance, the host MAY actively send ICMPv6 requests (or respond with an ICMPv6 response) inside the ESP tunnel to test the health of the associated IPsec security associations. Alternatively, the host MAY use UPDATE packets as a substitute. A minimal UPDATE packet would consist of a SEQ and ECHO_REQ_SIGN parameters, and a more complex would involve rekeying procedures as specified in section 6.8 in [RFC7402]. It is worth noting that a host actively sending periodic UPDATE packets to a busy server may increase the computational load of the server since it has to verify HMACs and signatures in UPDATE messages.

5.4. NAT Traversal Mode Parameter

The format of NAT traversal mode parameter is borrowed from Legacy ICE-HIP [RFC5770]. The format of the NAT_TRAVERSAL_MODE parameter is similar to the format of the ESP_TRANSFORM parameter in [RFC7402] and is shown in Figure 8. The Native ICE-HIP extension specified in this document defines the new NAT traversal mode identifier for ICE-HIP-UDP and reuses the UDP-ENCAPSULATION mode from Legacy ICE-HIP [RFC5770]. The identifier named RESERVED is reserved for future use. Future specifications may define more traversal modes.


 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           Reserved            |            Mode ID #1         |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           Mode ID #2          |            Mode ID #3         |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           Mode ID #n          |             Padding           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type       608
Length     length in octets, excluding Type, Length, and padding
Reserved   zero when sent, ignored when received
Mode ID    defines the proposed or selected NAT traversal mode(s)

The following NAT traversal mode IDs are defined:

    ID name            Value
    RESERVED             0
    UDP-ENCAPSULATION    1
    ICE-HIP-UDP          3
                

Figure 8: Format of the NAT_TRAVERSAL_MODE Parameter

The sender of a NAT_TRAVERSAL_MODE parameter MUST make sure that there are no more than six (6) Mode IDs in one NAT_TRAVERSAL_MODE parameter. Conversely, a recipient MUST be prepared to handle received NAT traversal mode parameters that contain more than six Mode IDs by accepting the first six Mode IDs and dropping the rest. The limited number of Mode IDs sets the maximum size of the NAT_TRAVERSAL_MODE parameter. The modes MUST be in preference order, most preferred mode(s) first.

Implementations conforming to this specification MUST implement UDP-ENCAPSULATION and SHOULD implement ICE-HIP-UDP modes.

5.5. Connectivity Check Transaction Pacing Parameter

The TRANSACTION_PACING is a new parameter, and it shown in Figure 9 contains only the connectivity check pacing value, expressed in milliseconds, as a 32-bit unsigned integer.


 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                            Min Ta                             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type     610
Length   4
Min Ta   the minimum connectivity check transaction pacing 
         value the host would use (in milliseconds) 
                

Figure 9: Format of the TRANSACTION_PACING Parameter

5.6. Relay and Registration Parameters

The format of the REG_FROM, RELAY_FROM, and RELAY_TO parameters is shown in Figure 10. All parameters are identical except for the type. REG_FROM is the only parameter covered with the signature.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Port              |    Protocol   |     Reserved  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                            Address                            |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type       REG_FROM:   950
           RELAY_FROM: 63998
           RELAY_TO:   64002
Length     20 
Port       transport port number; zero when plain IP is used
Protocol   IANA assigned, Internet Protocol number. 
           17 for UDP, 0 for plain IP
Reserved   reserved for future use; zero when sent, ignored 
           when received
Address    an IPv6 address or an IPv4 address in "IPv4-Mapped 
           IPv6 address" format
                

Figure 10: Format of the REG_FROM, RELAY_FROM, and RELAY_TO Parameters

REG_FROM contains the transport address and protocol from which the Control Relay Server sees the registration coming. RELAY_FROM contains the address from which the relayed packet was received by the Control Relay Server and the protocol that was used. RELAY_TO contains the same information about the address to which a packet should be forwarded.

5.7. LOCATOR_SET Parameter

This specification reuses the format for UDP-based locators as specified in Legacy ICE-HIP [RFC5770] to be used for communicating the address candidates between two hosts. The generic and NAT-traversal-specific locator parameters are illustrated in Figure 11.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |            Length             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Traffic Type  |  Locator Type | Locator Length|  Reserved   |P|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       Locator Lifetime                        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                            Locator                            |
|                                                               |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
.                                                               .
.                                                               .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Traffic Type  |  Loc Type = 2 | Locator Length|  Reserved   |P|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       Locator Lifetime                        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|     Transport Port            |  Transp. Proto|     Kind      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                           Priority                            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                              SPI                              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                            Address                            |
|                                                               |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Figure 11: LOCATOR_SET Parameter

The individual fields in the LOCATOR_SET parameter are described in Table 1.

Fields of the LOCATOR_SET Parameter
Field Value(s) Purpose
Type 193 Parameter type
Length Variable Length in octets, excluding Type and Length fields and padding
Traffic Type 0-2 Is the locator for HIP signaling (1), for ESP (2), or for both (0)
Locator Type 2 "Transport address" locator type
Locator Length 7 Length of the fields after Locator Lifetime in 4-octet units
Reserved 0 Reserved for future extensions
Preferred (P) bit 0 or 1 Set to 1 for a Locator in R1 if the Responder can use it for the rest of the base exchange, otherwise set to zero
Locator Lifetime Variable Locator lifetime in seconds
Transport Port Variable Transport layer port number
Transport Protocol Variable IANA assigned, transport layer Internet Protocol number. Currently only UDP (17) is supported.
Kind Variable 0 for host, 1 for server reflexive, 2 for peer reflexive or 3 for relayed address
Priority Variable Locator's priority as described in [I-D.ietf-ice-rfc5245bis]. It is worth noting that while the priority of a single locator candidate is 32-bits, but an implementation should use a 64-bit integer to calculate the priority of a candidate pair for the ICE priority algorithm.
SPI Variable Security Parameter Index (SPI) value that the host expects to see in incoming ESP packets that use this locator
Address Variable IPv6 address or an "IPv4-Mapped IPv6 address" format IPv4 address [RFC4291]

5.8. RELAY_HMAC Parameter

As specified in Legacy ICE-HIP [RFC5770], the RELAY_HMAC parameter value has the TLV type 65520. It has the same semantics as RVS_HMAC [RFC8004].

5.9. Registration Types

The REG_INFO, REG_REQ, REG_RESP, and REG_FAILED parameters contain Registration Type [RFC8003] values for Control Relay Server registration. The value for RELAY_UDP_HIP is 2 as specified in Legacy ICE-HIP [RFC5770].

5.10. Notify Packet Types

A Control Relay Server and end-hosts can use NOTIFY packets to signal different error conditions. The NOTIFY packet types are the same as in Legacy ICE-HIP [RFC5770].

The Notify Packet Types [RFC7401] are shown below. The Notification Data field for the error notifications SHOULD contain the HIP header of the rejected packet and SHOULD be empty for the CONNECTIVITY_CHECKS_FAILED type.

NOTIFICATION PARAMETER - ERROR TYPES     Value
------------------------------------     -----

NO_VALID_NAT_TRAVERSAL_MODE_PARAMETER      60
        

CONNECTIVITY_CHECKS_FAILED                 61
         

MESSAGE_NOT_RELAYED                        62
         

5.11. ESP Data Packets

The format for ESP data packets is identical to Legacy ICE-HIP [RFC5770].

[RFC3948] describes the UDP encapsulation of the IPsec ESP transport and tunnel mode. On the wire, the HIP ESP packets do not differ from the transport mode ESP, and thus the encapsulation of the HIP ESP packets is same as the UDP encapsulation transport mode ESP. However, the (semantic) difference to Bound End-to-End Tunnel (BEET) mode ESP packets used by HIP is that IP header is not used in BEET integrity protection calculation.

During the HIP base exchange, the two peers exchange parameters that enable them to define a pair of IPsec ESP security associations (SAs) as described in [RFC7402]. When two peers perform a UDP-encapsulated base exchange, they MUST define a pair of IPsec SAs that produces UDP-encapsulated ESP data traffic.

The management of encryption/authentication protocols and SPIs is defined in [RFC7402]. The UDP encapsulation format and processing of HIP ESP traffic is described in Section 6.1 of [RFC7402].

5.12. RELAYED_ADDRESS and MAPPED_ADDRESS Parameters

While the type values are new, the format of the RELAYED_ADDRESS and MAPPED_ADDRESS parameters (Figure 12) is identical to REG_FROM, RELAY_FROM and RELAY_TO parameters. This document specifies only the use of UDP relaying, and, thus, only protocol 17 is allowed. However, future documents may specify support for other protocols.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Port              |    Protocol   |    Reserved   |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                            Address                            |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type      [TBD by IANA; 
          RELAYED_ADDRESS: 4650
          MAPPED_ADDRESS:  4660]
Length    20 
Port      the UDP port number
Protocol  IANA assigned, Internet Protocol number (17 for UDP)
Reserved  reserved for future use; zero when sent, ignored 
          when received
Address   an IPv6 address or an IPv4 address in "IPv4-Mapped 
          IPv6 address" format
                

Figure 12: Format of the RELAYED_ADDRESS and MAPPED_ADDRESS Parameters

5.13. PEER_PERMISSION Parameter

The format of the new PEER_PERMISSION parameter is shown in Figure 13. The parameter is used for setting up and refreshing forwarding rules and the permissions for data packets at the Data Relay Server. The parameter contains one or more sets of Port, Protocol, Address, Outbound SPI (OSPI), and Inbound SPI (ISPI) values. One set defines a rule for one peer address.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Port              |    Protocol   |    Reserved   |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                             Address                           |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                              OSPI                             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                              ISPI                             |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                              ...                              |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type      [TBD by IANA; 4680]
Length    length in octets, excluding Type and Length
Port      the transport layer (UDP) port number of the peer
Protocol  IANA assigned, Internet Protocol number (17 for UDP)
Reserved  reserved for future use; zero when sent, ignored 
          when received
Address   an IPv6 address, or an IPv4 address in "IPv4-Mapped
          IPv6 address" format, of the peer
OSPI      the outbound SPI value the Data Relay Client is using for
          the peer with the Address and Port
ISPI      the inbound SPI value the Data Relay Client is using for
          the peer with the Address and Port
                

Figure 13: Format of the PEER_PERMISSION Parameter

5.14. HIP Connectivity Check Packets

The connectivity request messages are HIP UPDATE packets containing a new CANDIDATE_PRIORITY parameter (Figure 14). Response UPDATE packets contain a MAPPED_ADDRESS parameter (Figure 12).

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                            Priority                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type      [TBD by IANA; 4700]
Length    4
Priority  the priority of a (potential) peer reflexive candidate
                

Figure 14: Format of the CANDIDATE_PRIORITY Parameter

5.15. NOMINATE parameter

Figure 15 shows the NOMINATE parameter that is used to conclude the candidate nomination process.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|             Type              |             Length            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                           Reserved                            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type      [TBD by IANA; 4710]
Length    4
Reserved  Reserved for future extension purposes
                

Figure 15: Format of the NOMINATE Parameter

6. Security Considerations

The security considerations are the same as in Legacy ICE-HIP [RFC5770], but are repeated here for the sake of completeness.

6.1. Privacy Considerations

The locators are in plain text format in favor of inspection at HIP-aware middleboxes in the future. The current document does not specify encrypted versions of LOCATOR_SETs, even though it could be beneficial for privacy reasons to avoid disclosing them to middleboxes.

It is also possible that end-users may not want to reveal all locators to each other. For example, tracking the physical location of a multihoming end-host may become easier if it reveals all locators to its peer during a base exchange. Also, revealing host addresses exposes information about the local topology that may not be allowed in all corporate environments. For these two reasons, an end-host may exclude certain host addresses from its LOCATOR_SET parameter. However, such behavior creates non-optimal paths when the hosts are located behind the same NAT. Especially, this could be problematic with a legacy NAT that does not support routing from the private address realm back to itself through the outer address of the NAT. This scenario is referred to as the hairpin problem [RFC5128]. With such a legacy NAT, the only option left would be to use a relayed transport address from a TURN server.

The use of Control and Data Relay Servers can be also useful for privacy purposes. For example, a privacy concerned Responder may reveal only its Control Relay Server and Relayed candidates to Initiators. This same mechanism also protects the Responder against Denial-of-Service (DoS) attacks by allowing the Responder to initiate new connections even if its relays would be unavailable due to a DoS attack.

6.2. Opportunistic Mode

A Control Relay Server should have one address per Control Relay Client when the Control Relay Server is serving more than one Control Relay Client and supports opportunistic mode. Otherwise, it cannot be guaranteed that the Control Relay Server can deliver the I1 packet to the intended recipient.

6.3. Base Exchange Replay Protection for Control Relay Server

In certain scenarios, it is possible that an attacker, or two attackers, can replay an earlier base exchange through a Control Relay Server by masquerading as the original Initiator and Responder. The attack does not require the attacker(s) to compromise the private key(s) of the attacked host(s). However, for this attack to succeed, the legimitate Responder has to be disconnected from the Control Relay Server.

The Control Relay Server can protect itself against replay attacks by becoming involved in the base exchange by introducing nonces that the end-hosts (Initiator and Responder) are required to sign. One way to do this is to add ECHO_REQUEST_M parameters to the R1 and I2 packets as described in [HIP-MIDDLE] and drop the I2 or R2 packets if the corresponding ECHO_RESPONSE_M parameters are not present.

6.4. Demultiplexing Different HIP Associations

Section 5.1 of [RFC3948] describes a security issue for the UDP encapsulation in the standard IP tunnel mode when two hosts behind different NATs have the same private IP address and initiate communication to the same Responder in the public Internet. The Responder cannot distinguish between two hosts, because security associations are based on the same inner IP addresses.

This issue does not exist with the UDP encapsulation of HIP ESP transport format because the Responder uses HITs to distinguish between different Initiators.

6.5. Reuse of Ports at the Data Relay Server

If the Data Relay Server uses the same relayed address and port (as conveyed in the RELAYED_ADDRESS parameter) for multiple Data Relay Clients, it appears to all the peers, and their firewalls, that all the Data Relay Clients are at the same address. Thus, a stateful firewall may allow packets pass from hosts that would not normally be able to send packets to a peer behind the firewall. Therefore, a Data Relay Server SHOULD NOT re-use the port numbers. If port numbers need to be re-used, the Data Relay Server SHOULD have a sufficiently large pool of port numbers and select ports from the pool randomly to decrease the chances of a Data Relay Client obtaining the same address that a another host behind the same firewall is using.

6.6. Amplification attacks

A malicious host may send an invalid list of candidates for its peer that are used for targeting a victim host by flooding it with connectivity checks. To mitigate the attack, this protocol adopts the ICE mechanism to cap the total amount of connectivity checks as defined in section Section 4.7.

6.7. Attacks against Connectivity Checks and Candidate Gathering

[I-D.ietf-ice-rfc5245bis] describes attacks against ICE connectivity checks. HIP bases its control plane security on Diffie-Hellman key exchange, public keys and Hashed Message Authentication codes, meaning that the mentioned security concerns do not apply to HIP either. The mentioned section discusses also of man-in-the-middle replay attacks that are difficult to prevent. The connectivity checks in this protocol are immune against replay attacks because a connectivity request includes a random nonce that the recipient must sign and send back as a response.

[I-D.ietf-ice-rfc5245bis] describes attacks on server reflexive address gathering. Similarly here, if the DNS, a Control Relay Server or a Data Relay Server has been compromised, not much can be done. However, the case where attacker can inject fake messages (located on a shared network segment like Wifi) does not apply here. HIP messages are integrity and replay protected, so it is not possible inject fake server reflexive address candidates.

[I-D.ietf-ice-rfc5245bis] describes attacks on relayed candidate gathering. Similarly to ICE TURN servers, Data Relay Server require an authenticated base exchange that protects relayed address gathering against fake requests and responses. Further, replay attacks are not possible because the HIP base exchange (and also UPDATE procedure) is protected against replay attacks.

7. IANA Considerations

This section is to be interpreted according to [RFC5226].

This document updates the IANA Registry for HIP Parameter Types [RFC7401] by assigning new HIP Parameter Type values for the new HIP Parameters: RELAYED_ADDRESS, MAPPED_ADDRESS (defined in Section 5.12), and PEER_PERMISSION (defined in Section 5.13).

This document updates the IANA Registry for HIP NAT traversal modes specified in Legacy ICE-HIP [RFC5770] by assigning value for the NAT traversal mode ICE-HIP-UDP (defined in Section 5.4) This specification introduces a new keepalive Notify message type field NAT_KEEPALIVE.

This document defines additional registration types for the HIP Registration Extension [RFC8003] that allow registering with a Data Relay Server for ESP relaying service: RELAY_UDP_ESP (defined in Section 4.1, and performing server reflexive candidate discovery: CANDIDATE_DISCOVERY (defined in Section 4.2).

ICE specification [I-D.ietf-ice-rfc5245bis] discusses "Unilateral Self-Address Fixing" . This protocol is based on ICE, and thus the same considerations apply also here with one exception: this protocol does not hide binary IP addresses from application-level gateways.

8. Contributors

Marcelo Bagnulo, Philip Matthews and Hannes Tschofenig have contributed to [RFC5770]. This document leans heavily on the work in the RFC.

9. Acknowledgments

Thanks to Jonathan Rosenberg and the rest of the MMUSIC WG folks for the excellent work on ICE. In addition, the authors would like to thank Andrei Gurtov, Simon Schuetz, Martin Stiemerling, Lars Eggert, Vivien Schmitt, and Abhinav Pathak for their contributions and Tobias Heer, Teemu Koponen, Juhana Mattila, Jeffrey M. Ahrenholz, Kristian Slavov, Janne Lindqvist, Pekka Nikander, Lauri Silvennoinen, Jukka Ylitalo, Juha Heinanen, Joakim Koskela, Samu Varjonen, Dan Wing, Tom Henderson, Alex Elsayed and Jani Hautakorpi for their comments to [RFC5770], which is the basis for this document.

This work has been partially funded by CyberTrust programme by Digile/Tekes in Finland.

10. References

10.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997.
[RFC7401] Moskowitz, R., Heer, T., Jokela, P. and T. Henderson, "Host Identity Protocol Version 2 (HIPv2)", RFC 7401, DOI 10.17487/RFC7401, April 2015.
[RFC8003] Laganier, J. and L. Eggert, "Host Identity Protocol (HIP) Registration Extension", RFC 8003, DOI 10.17487/RFC8003, October 2016.
[RFC8004] Laganier, J. and L. Eggert, "Host Identity Protocol (HIP) Rendezvous Extension", RFC 8004, DOI 10.17487/RFC8004, October 2016.
[RFC8046] Henderson, T., Vogt, C. and J. Arkko, "Host Mobility with the Host Identity Protocol", RFC 8046, DOI 10.17487/RFC8046, February 2017.
[RFC8047] Henderson, T., Vogt, C. and J. Arkko, "Host Multihoming with the Host Identity Protocol", RFC 8047, DOI 10.17487/RFC8047, February 2017.
[RFC5770] Komu, M., Henderson, T., Tschofenig, H., Melen, J. and A. Keranen, "Basic Host Identity Protocol (HIP) Extensions for Traversal of Network Address Translators", RFC 5770, DOI 10.17487/RFC5770, April 2010.
[RFC5389] Rosenberg, J., Mahy, R., Matthews, P. and D. Wing, "Session Traversal Utilities for NAT (STUN)", RFC 5389, DOI 10.17487/RFC5389, October 2008.
[RFC7402] Jokela, P., Moskowitz, R. and J. Melen, "Using the Encapsulating Security Payload (ESP) Transport Format with the Host Identity Protocol (HIP)", RFC 7402, DOI 10.17487/RFC7402, April 2015.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", RFC 5226, DOI 10.17487/RFC5226, May 2008.
[I-D.ietf-ice-rfc5245bis] Keranen, A., Holmberg, C. and J. Rosenberg, "Interactive Connectivity Establishment (ICE): A Protocol for Network Address Translator (NAT) Traversal", Internet-Draft draft-ietf-ice-rfc5245bis-12, September 2017.
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z. and W. Weiss, "An Architecture for Differentiated Services", RFC 2475, DOI 10.17487/RFC2475, December 1998.

10.2. Informative References

[RFC4423] Moskowitz, R. and P. Nikander, "Host Identity Protocol (HIP) Architecture", RFC 4423, DOI 10.17487/RFC4423, May 2006.
[RFC5201] Moskowitz, R., Nikander, P., Jokela, P. and T. Henderson, "Host Identity Protocol", RFC 5201, DOI 10.17487/RFC5201, April 2008.
[RFC5207] Stiemerling, M., Quittek, J. and L. Eggert, "NAT and Firewall Traversal Issues of Host Identity Protocol (HIP) Communication", RFC 5207, DOI 10.17487/RFC5207, April 2008.
[RFC6538] Henderson, T. and A. Gurtov, "The Host Identity Protocol (HIP) Experiment Report", RFC 6538, DOI 10.17487/RFC6538, March 2012.
[MMUSIC-ICE] Rosenberg, J., "Guidelines for Usage of Interactive Connectivity Establishment (ICE) by non Session Initiation Protocol (SIP) Protocols", Work in Progress, July 2008.
[RFC5128] Srisuresh, P., Ford, B. and D. Kegel, "State of Peer-to-Peer (P2P) Communication across Network Address Translators (NATs)", RFC 5128, DOI 10.17487/RFC5128, March 2008.
[HIP-MIDDLE] Heer, T., Wehrle, K. and M. Komu, "End-Host Authentication for HIP Middleboxes", Work in Progress, February 2009.
[RFC3948] Huttunen, A., Swander, B., Volpe, V., DiBurro, L. and M. Stenberg, "UDP Encapsulation of IPsec ESP Packets", RFC 3948, DOI 10.17487/RFC3948, January 2005.

Appendix A. Selecting a Value for Check Pacing

Selecting a suitable value for the connectivity check transaction pacing is essential for the performance of connectivity check-based NAT traversal. The value should not be so small that the checks cause network congestion or overwhelm the NATs. On the other hand, a pacing value that is too high makes the checks last for a long time, thus increasing the connection setup delay.

The Ta value may be configured by the user in environments where the network characteristics are known beforehand. However, if the characteristics are not known, it is recommended that the value is adjusted dynamically. In this case, it is recommended that the hosts estimate the round-trip time (RTT) between them and set the minimum Ta value so that only two connectivity check messages are sent on every RTT.

One way to estimate the RTT is to use the time that it takes for the Control Relay Server registration exchange to complete; this would give an estimate on the registering host's access link's RTT. Also, the I1/R1 exchange could be used for estimating the RTT, but since the R1 can be cached in the network, or the relaying service can increase the delay notably, this is not recommended.

Appendix B. Differences with respect to ICE

The Native ICE-HIP protocol specified in this document follows the semantics of ICE as close as possible, and most of the differences are syntactical due to the use of a different protocol. In this section, we describe the differences to the ICE protocol.

Appendix C. Differences to Base Exchange and UPDATE procedures

This section gives some design guidance for implementers how the extensions in this protocol extends and differs from [RFC7401] and [RFC8046].

Authors' Addresses

Ari Keranen Ericsson Hirsalantie 11 02420 Jorvas, Finland EMail: ari.keranen@ericsson.com
Jan Melén Ericsson Hirsalantie 11 02420 Jorvas, Finland EMail: jan.melen@ericsson.com
Miika Komu (editor) Ericsson Hirsalantie 11 02420 Jorvas, Finland EMail: miika.komu@ericsson.com