CoRE M. Veillette, Ed. Internet-Draft Trilliant Networks Inc. Intended status: Standards Track P. van der Stok, Ed. Expires: November 16, 2019 consultant A. Pelov Acklio A. Bierman YumaWorks May 15, 2019 CoAP Management Interface draft-ietf-core-comi-05 Abstract This document describes a network management interface for constrained devices and networks, called CoAP Management Interface (CoMI). The Constrained Application Protocol (CoAP) is used to access datastore and data node resources specified in YANG, or SMIv2 converted to YANG. CoMI uses the YANG to CBOR mapping and converts YANG identifier strings to numeric identifiers for payload size reduction. The complete solution composed of CoMI, [I-D.ietf-core-yang-cbor] and [I-D.ietf-core-sid] is called CORECONF. CORECONF extends the set of YANG based protocols, NETCONF and RESTCONF, with the capability to manage constrained devices and networks. Note Discussion and suggestions for improvement are requested, and should be sent to yot@ietf.org. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." Veillette, et al. Expires November 16, 2019 [Page 1] Internet-Draft CoMI May 2019 This Internet-Draft will expire on November 16, 2019. Copyright Notice Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4 2. CoMI Architecture . . . . . . . . . . . . . . . . . . . . . . 5 2.1. Major differences between RESTCONF and CoMI . . . . . . . 6 2.2. Compression of YANG identifiers . . . . . . . . . . . . . 7 2.3. Instance identifier . . . . . . . . . . . . . . . . . . . 8 2.4. Content-Formats . . . . . . . . . . . . . . . . . . . . . 8 2.5. Unified datastore . . . . . . . . . . . . . . . . . . . . 10 3. Example syntax . . . . . . . . . . . . . . . . . . . . . . . 11 4. CoAP Interface . . . . . . . . . . . . . . . . . . . . . . . 11 4.1. Using the 'k' Uri-Query option . . . . . . . . . . . . . 13 4.2. Data Retrieval . . . . . . . . . . . . . . . . . . . . . 14 4.2.1. Using the 'c' Uri-Query option . . . . . . . . . . . 14 4.2.2. Using the 'd' Uri-Query option . . . . . . . . . . . 15 4.2.3. GET . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.2.4. FETCH . . . . . . . . . . . . . . . . . . . . . . . . 18 4.3. Data Editing . . . . . . . . . . . . . . . . . . . . . . 19 4.3.1. Data Ordering . . . . . . . . . . . . . . . . . . . . 19 4.3.2. POST . . . . . . . . . . . . . . . . . . . . . . . . 19 4.3.3. PUT . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.3.4. iPATCH . . . . . . . . . . . . . . . . . . . . . . . 21 4.3.5. DELETE . . . . . . . . . . . . . . . . . . . . . . . 22 4.4. Full datastore access . . . . . . . . . . . . . . . . . . 23 4.4.1. Full datastore examples . . . . . . . . . . . . . . . 23 4.5. Event stream . . . . . . . . . . . . . . . . . . . . . . 24 4.5.1. Notify Examples . . . . . . . . . . . . . . . . . . . 25 4.5.2. The 'f' Uri-Query option . . . . . . . . . . . . . . 26 4.6. RPC statements . . . . . . . . . . . . . . . . . . . . . 27 4.6.1. RPC Example . . . . . . . . . . . . . . . . . . . . . 27 Veillette, et al. Expires November 16, 2019 [Page 2] Internet-Draft CoMI May 2019 5. Use of Block . . . . . . . . . . . . . . . . . . . . . . . . 29 6. Application Discovery . . . . . . . . . . . . . . . . . . . . 29 6.1. YANG library . . . . . . . . . . . . . . . . . . . . . . 29 6.2. Resource Discovery . . . . . . . . . . . . . . . . . . . 30 6.2.1. Datastore Resource Discovery . . . . . . . . . . . . 30 6.2.2. Data node Resource Discovery . . . . . . . . . . . . 30 6.2.3. Event stream Resource Discovery . . . . . . . . . . . 31 7. Error Handling . . . . . . . . . . . . . . . . . . . . . . . 31 8. Security Considerations . . . . . . . . . . . . . . . . . . . 35 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 35 9.1. Resource Type (rt=) Link Target Attribute Values Registry 35 9.2. CoAP Content-Formats Registry . . . . . . . . . . . . . . 36 9.3. Media Types Registry . . . . . . . . . . . . . . . . . . 36 10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 38 11. References . . . . . . . . . . . . . . . . . . . . . . . . . 38 11.1. Normative References . . . . . . . . . . . . . . . . . . 38 11.2. Informative References . . . . . . . . . . . . . . . . . 40 Appendix A. ietf-comi YANG module . . . . . . . . . . . . . . . 40 Appendix B. ietf-comi .sid file . . . . . . . . . . . . . . . . 46 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 49 1. Introduction The Constrained Application Protocol (CoAP) [RFC7252] is designed for Machine to Machine (M2M) applications such as smart energy, smart city and building control. Constrained devices need to be managed in an automatic fashion to handle the large quantities of devices that are expected in future installations. Messages between devices need to be as small and infrequent as possible. The implementation complexity and runtime resources need to be as small as possible. This draft describes the CoAP Management Interface which uses CoAP methods to access structured data defined in YANG [RFC7950]. This draft is complementary to [RFC8040] which describes a REST-like interface called RESTCONF, which uses HTTP methods to access structured data defined in YANG. The use of standardized data models specified in a standardized language, such as YANG, promotes interoperability between devices and applications from different manufacturers. CoMI and RESTCONF are intended to work in a stateless client-server fashion. They use a single round-trip to complete a single editing transaction, where NETCONF needs multiple round trips. To promote small messges, CoMI uses a YANG to CBOR mapping [I-D.ietf-core-yang-cbor] and numeric identifiers [I-D.ietf-core-sid] to minimize CBOR payloads and URI length. Veillette, et al. Expires November 16, 2019 [Page 3] Internet-Draft CoMI May 2019 1.1. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. The following terms are defined in the YANG data modelling language [RFC7950]: action, anydata, anyxml, client, container, data model, data node, identity, instance identifier, leaf, leaf-list, list, module, RPC, schema node, server, submodule. The following terms are defined in [RFC6241]: configuration data, datastore, state data The following term is defined in [I-D.ietf-core-sid]: YANG schema item identifier (SID). The following terms are defined in the CoAP protocol [RFC7252]: Confirmable Message, Content-Format, Endpoint. The following terms are defined in this document: data node resource: a CoAP resource that models a YANG data node. datastore resource: a CoAP resource that models a YANG datastore. event stream resource: a CoAP resource used by clients to observe YANG notifications. notification instance: An instance of a schema node of type notification, specified in a YANG module implemented by the server. The instance is generated in the server at the occurrence of the corresponding event and reported by an event stream. list instance identifier: Handle used to identify a YANG data node that is an instance of a YANG "list" specified with the values of the key leaves of the list. single instance identifier: Handle used to identify a specific data node which can be instantiated only once. This includes data nodes defined at the root of a YANG module and data nodes defined within a container. This excludes data nodes defined within a list or any children of these data nodes. instance-identifier: List instance identifier or single instance identifier. Veillette, et al. Expires November 16, 2019 [Page 4] Internet-Draft CoMI May 2019 instance-value: The value assigned to a schema node instance. Schema node values are serialized into the payload according to the rules defined in section 4 of [I-D.ietf-core-yang-cbor]. 2. CoMI Architecture This section describes the CoMI architecture to use CoAP for reading and modifying the content of datastore(s) used for the management of the instrumented node. +----------------------------------------------------------------+ | SMIv2 specification (2) | +----------------------------------------------------------------+ | V +----------------------------------------------------------------+ | YANG specification (1) | +----------------------------------------------------------------+ | | Client V Server V +----------------+ +-----------------------+ | Request |--> CoAP request(3) -->| Indication | | Confirm |<-- CoAP response(3)<--| Response (4) | | | | | | |<==== Security (7) ===>|+---------------------+| +----------------+ || Datastore(s) (5) || |+---------------------+| |+---------------------+| || Event stream(s) (6) || |+---------------------+| +-----------------------+ Figure 1: Abstract CoMI architecture Figure 1 is a high-level representation of the main elements of the CoMI management architecture. The different numbered components of Figure 1 are discussed according to component number. (1) YANG specification: contains a set of named and versioned modules. (2) SMIv2 specification: A named module specifies a set of variables and "conceptual tables". There is an algorithm to translate SMIv2 specifications to YANG specifications. (3) CoAP request/response messages: The CoMI client sends request messages to and receives response messages from the CoMI server. Veillette, et al. Expires November 16, 2019 [Page 5] Internet-Draft CoMI May 2019 (4) Request, Indication, Response, Confirm: Processes performed by the CoMI clients and servers. (5) Datastore: A resource used to access configuration data, state data, RPCs and actions. A CoMI server may support a single unified datastore or multiple datastores as those defined by Network Management Datastore Architecture (NMDA) [RFC8342]. (6) Event stream: A resource used to get real time notifications. A CoMI server may support multiple Event streams serving different purposes such as normal monitoring, diagnostic, syslog, security monitoring. (7) Security: The server MUST prevent unauthorized users from reading or writing any CoMI resources. CoMI relies on security protocols such as DTLS [RFC6347] to secure CoAP communications. 2.1. Major differences between RESTCONF and CoMI CoMI is a RESTful protocol for small devices where saving bytes to transport counts. Contrary to RESTCONF, many design decisions are motivated by the saving of bytes. Consequently, CoMI is not a RESTCONF over CoAP protocol, but differs more significantly from RESTCONF. Some major differences are cited below: o CoMI uses CoAP/UDP as transport protocol and CBOR as payload format [I-D.ietf-core-yang-cbor]. RESTCONF uses HTTP/TCP as transport protocol and JSON or XML as payload formats. o CoMI encodes YANG identifier strings as numbers, where RESTCONF does not. o CoMI uses the methods FETCH and iPATCH to access multiple data nodes. RESTCONF uses instead the HTTP method PATCH and the HTTP method GET with the "fields" Query parameter. o RESTCONF uses the HTTP methods HEAD, and OPTIONS, which are not supported by CoAP. o CoMI does not support "insert" query parameter (first, last, before, after) and the "point" query parameter which are supported by RESTCONF. o CoMI does not support the "start-time" and "stop-time" query parameters to retrieve past notifications. o CoMI does not support the "filter" query parameters to observe a specific set of notifications. Veillette, et al. Expires November 16, 2019 [Page 6] Internet-Draft CoMI May 2019 o CoMI also differ in the handling of default values, only 'report- all' and 'trip' options are supported. 2.2. Compression of YANG identifiers In the YANG specification, items are identified with a name string. In order to significantly reduce the size of identifiers used in CoMI, numeric identifiers are used instead of these strings. YANG Schema Item iDentifier (SID) is defined in [I-D.ietf-core-yang-cbor] section 2.1. When used in a URI, SIDs are encoded in based64 using the URL and Filename safe alphabet as defined by [RFC4648] section 5. The last 6 bits encoded is always aligned with the least significant 6 bits of the SID represented using an unsigned integer. 'A' characters (value 0) at the start of the resulting string are removed. SID in basae64 = URLsafeChar[SID >> 60 & 0x3F] | URLsafeChar[SID >> 54 & 0x3F] | URLsafeChar[SID >> 48 & 0x3F] | URLsafeChar[SID >> 42 & 0x3F] | URLsafeChar[SID >> 36 & 0x3F] | URLsafeChar[SID >> 30 & 0x3F] | URLsafeChar[SID >> 24 & 0x3F] | URLsafeChar[SID >> 18 & 0x3F] | URLsafeChar[SID >> 12 & 0x3F] | URLsafeChar[SID >> 6 & 0x3F] | URLsafeChar[SID & 0x3F] For example, SID 1721 is encoded as follow. URLsafeChar[1721 >> 60 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 54 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 48 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 42 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 36 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 30 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 24 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 18 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 12 & 0x3F] = URLsafeChar[0] = 'A' URLsafeChar[1721 >> 6 & 0x3F] = URLsafeChar[26] = 'a' URLsafeChar[1721 & 0x3F] = URLsafeChar[57] = '5' The resulting base64 representation of SID 1721 is "a5" Veillette, et al. Expires November 16, 2019 [Page 7] Internet-Draft CoMI May 2019 2.3. Instance identifier Instance identifiers are used to uniquely identify data node instances within a datastore. This YANG built-in type is defined in [RFC7950] section 9.13. An instance identifier is composed of the data node identifier (i.e. a SID) and for data nodes within list(s) the keys used to index within these list(s). When part of a payload, instance identifiers are encoded in CBOR based on the rules defined in [I-D.ietf-core-yang-cbor] section 6.13.1. When part of a URI, the SID is appended to the URI of the targeted datastore, the keys are specified using the 'k' URI-Query as defined in Section 4.1. 2.4. Content-Formats ComI uses Content-Formats based on the YANG to CBOR mapping specified in [I-D.ietf-core-yang-cbor]. The following Content-formats are defined: application/yang-data+cbor: This Content-Format represents a CBOR YANG document containing one or multiple data node values. Each data node is identified by its associated SID. FORMAT: CBOR map of SID, instance-value The message payload of Content-Format 'application/yang-data+cbor' is encoded using a CBOR map. Each entry of this CBOR map is composed of a key and a value. CBOR map keys are set to the SID assigned to the data nodes, CBOR map values are set to the instance value as defined in [I-D.ietf-core-yang-cbor] section 4. application/yang-identifiers+cbor: This Content-Format represents a CBOR YANG document containing a list of instance identifier used to target specific data node instances within a datastore. FORMAT: CBOR array of instance-identifier The message payload of Content-Format 'application/yang- identifiers+cbor' is encoded using a CBOR array. Each entry of this CBOR array contain an instance identifier encoded as defined in [I-D.ietf-core-yang-cbor] section 6.13.1. application/yang-instances+cbor: This Content-Format represents a CBOR YANG document containing a list of data node instances. Each data node instance is identified by its associated instance identifier. Veillette, et al. Expires November 16, 2019 [Page 8] Internet-Draft CoMI May 2019 FORMAT: CBOR array of CBOR map of instance-identifier, instance- value The message payload of Content-Format 'application/yang- instances+cbor' is encoded using a CBOR array. Each entry within this CBOR array contains a CBOR map carrying an instance identifier and associated instance value. Instance identifiers are encoded using the rules defined in [I-D.ietf-core-yang-cbor] section 6.13.1, values are encoded using the rules defined in [I-D.ietf-core-yang-cbor] section 4. When present in an iPATCH request payload, this Content-Format carry a list of data node instances to be replaced, created, or deleted. For each data node instance D, for which the instance identifier is the same as a data node instance I, in the targeted datastore resource: the value of D replaces the value of I. When the value of D is null, the data node instance I is removed. When the targeted datastore resource does not contain a data node instance with the same instance identifier as D, a new instance is created with the same instance identifier and value as D. The different Content-format usages are summarized in the table below: Veillette, et al. Expires November 16, 2019 [Page 9] Internet-Draft CoMI May 2019 +---------------+--------------+------------------------------------+ | Method | Resource | Content-Format | +---------------+--------------+------------------------------------+ | GET response | data node | /application/yang-data+cbor | | | | | | PUT request | data node | /application/yang-data+cbor | | | | | | POST request | data node | /application/yang-data+cbor | | | | | | DELETE | data node | n/a | | | | | | GET response | datastore | /application/yang-data+cbor | | | | | | PUT request | datastore | /application/yang-data+cbor | | | | | | POST request | datastore | /application/yang-data+cbor | | | | | | FETCH request | datastore | /application/yang-identifiers+cbor | | | | | | FETCH | datastore | /application/yang-instances+cbor | | response | | | | | | | | iPATCH | datastore | /application/yang-instances+cbor | | request | | | | | | | | GET response | event stream | /application/yang-instances+cbor | | | | | | POST request | rpc, action | /application/yang-data+cbor | | | | | | POST response | rpc, action | /application/yang-data+cbor | +---------------+--------------+------------------------------------+ 2.5. Unified datastore CoMI supports a simple datastore model consisting of a single unified datastore. This datasore provides access to both configuration and operational data. Configuration updates performed on this datastore are reflected immediately or with a minimal delay as operational data. Alternatively, CoMI servers MAY implement a more complex datastore model such as the Network Management Datastore Architecture (NMDA) as defined by [RFC8342]. Each datastore supported is implemented as a datastore resource. Characteristics of the unified datastore are summarized in the table below: Veillette, et al. Expires November 16, 2019 [Page 10] Internet-Draft CoMI May 2019 +-------------+-----------------------------------------------------+ | Name | Value | +-------------+-----------------------------------------------------+ | Name | unified | | | | | YANG | all modules | | modules | | | | | | YANG nodes | all data nodes ("config true" and "config false") | | | | | Access | read-write | | | | | How applied | changes applied in place immediately or with a | | | minimal delay | | | | | Protocols | CORECONF | | | | | Defined in | "ietf-comi" | +-------------+-----------------------------------------------------+ 3. Example syntax CBOR is used to encode CoMI request and response payloads. The CBOR syntax of the YANG payloads is specified in [RFC7049]. The payload examples are notated in Diagnostic notation (defined in section 6 of [RFC7049]) that can be automatically converted to CBOR. SIDs in URIs are represented as a base64 number, SIDs in the payload are represented as decimal numbers. 4. CoAP Interface This note specifies a Management Interface. CoAP endpoints that implement the CoMI management protocol, support at least one discoverable management resource of resource type (rt): core.c.ds, with example path: /c, where c is short-hand for CoMI. The path /c is recommended, but not compulsory (see Section 6). The mapping of YANG data node instances to CoMI resources is as follows. Every data node of the YANG modules loaded in the CoMI server represents a sub-resource of the datastore resource (e.g. /c/ sid). When multiple instances of a list exist, instance selection is possible as described in Section 4.1, Section 4.2.3.1, and Section 4.2.4. CoMI also supports event stream resourced used to observe notification instances. Event stream resources can be discovered using resource type (rt): core.c.ev. Veillette, et al. Expires November 16, 2019 [Page 11] Internet-Draft CoMI May 2019 The description of the CoMI management interface is shown in the table below: +-------------+------------------+-----------+ | Function | Recommended path | rt | +-------------+------------------+-----------+ | Datastore | /c | core.c.ds | | | | | | Data node | /c/SID | core.c.dn | | | | | | Event steam | /s | core.c.ev | +-------------+------------------+-----------+ The path values are example values. On discovery, the server makes the actual path values known for these resources. The methods used by CoMI are: +-----------+-------------------------------------------------------+ | Operation | Description | +-----------+-------------------------------------------------------+ | GET | Retrieve the datastore resource or a data node | | | resource | | | | | FETCH | Retrieve specific data nodes within a datastore | | | resource | | | | | POST | Create a datastore resource or a data node resource, | | | invoke an RPC or action | | | | | PUT | Create or replace a datastore resource or a data node | | | resource | | | | | iPATCH | Idem-potently create, replace, and delete data node | | | resource(s) within a datastore resource | | | | | DELETE | Delete a datastore resource or a data node resource | +-----------+-------------------------------------------------------+ There is one Uri-Query option for the GET, PUT, POST, and DELETE methods. +------------------+----------------------------------------+ | Uri-Query option | Description | +------------------+----------------------------------------+ | k | Select an instance within YANG list(s) | +------------------+----------------------------------------+ Veillette, et al. Expires November 16, 2019 [Page 12] Internet-Draft CoMI May 2019 This parameter is not used for FETCH and iPATCH, because their request payloads support list instance selection. 4.1. Using the 'k' Uri-Query option The "k" (key) parameter specifies a specific instance of a data node. The SID in the URI is followed by the (?k=key1,key2,...). Where SID identifies a data node, and key1, key2 are the values of the key leaves that specify an instance. Lists can have multiple keys, and lists can be part of lists. The order of key value generation is given recursively by: o For a given list, if a parent data node is a list, generate the keys for the parent list first. o For a given list, generate key values in the order specified in the YANG module. Key values are encoded using the rules defined in the following table. +-----------------------------+--------------------------------+ | YANG datatype | Uri-Query text content | +-----------------------------+--------------------------------+ | uint8,uint16,unit32, uint64 | int2str(key) | | | | | int8, int16,int32, int64 | urlSafeBase64(CBORencode(key)) | | | | | decimal64 | urlSafeBase64(CBOR key) | | | | | string | key | | | | | boolean | "0" or "1" | | | | | enumeration | int2str(key) | | | | | bits | urlSafeBase64(CBORencode(key)) | | | | | binary | urlSafeBase64(key) | | | | | identityref | int2str(key) | | | | | union | urlSafeBase64(CBORencode(key)) | | | | | instance-identifier | urlSafeBase64(CBORencode(key)) | +-----------------------------+--------------------------------+ In this table: Veillette, et al. Expires November 16, 2019 [Page 13] Internet-Draft CoMI May 2019 o The method int2str() is used to convert an integer value to a string. For example, int2str(0x0123) return the string "291". o The method urlSafeBase64() is used to convert a binary string to base64 using the URL and Filename safe alphabet as defined by [RFC4648] section 5. For example, urlSafeBase64(\xF9\x56\xA1\x3C) return the string "-VahPA". o The method CBORencode() is used to convert a YANG value to CBOR as specified in [I-D.ietf-core-yang-cbor] section 6. The resulting key string is encoded in a Uri-Query as specified in [RFC7252] section 6.5. 4.2. Data Retrieval One or more data nodes can be retrieved by the client. The operation is mapped to the GET method defined in section 5.8.1 of [RFC7252] and to the FETCH method defined in section 2 of [RFC8132]. There are two additional Uri-Query options for the GET and FETCH methods. +-------------+-----------------------------------------------------+ | Uri-Query | Description | | option | | +-------------+-----------------------------------------------------+ | c | Control selection of configuration and non- | | | configuration data nodes (GET and FETCH) | | | | | d | Control retrieval of default values. | +-------------+-----------------------------------------------------+ 4.2.1. Using the 'c' Uri-Query option The 'c' (content) option controls how descendant nodes of the requested data nodes will be processed in the reply. The allowed values are: Veillette, et al. Expires November 16, 2019 [Page 14] Internet-Draft CoMI May 2019 +-------+-----------------------------------------------------+ | Value | Description | +-------+-----------------------------------------------------+ | c | Return only configuration descendant data nodes | | | | | n | Return only non-configuration descendant data nodes | | | | | a | Return all descendant data nodes | +-------+-----------------------------------------------------+ This option is only allowed for GET and FETCH methods on datastore and data node resources. A 4.02 (Bad Option) error is returned if used for other methods or resource types. If this Uri-Query option is not present, the default value is "a". 4.2.2. Using the 'd' Uri-Query option The "d" (with-defaults) option controls how the default values of the descendant nodes of the requested data nodes will be processed. The allowed values are: +-------+-----------------------------------------------------------+ | Value | Description | +-------+-----------------------------------------------------------+ | a | All data nodes are reported. Defined as 'report-all' in | | | section 3.1 of [RFC6243]. | | | | | t | Data nodes set to the YANG default are not reported. | | | Defined as 'trim' in section 3.2 of [RFC6243]. | +-------+-----------------------------------------------------------+ If the target of a GET or FETCH method is a data node that represents a leaf that has a default value, and the leaf has not been given a value by any client yet, the server MUST return the default value of the leaf. If the target of a GET method is a data node that represents a container or list that has child resources with default values, and these have not been given value yet, The server MUST not return the child resource if d= 't' The server MUST return the child resource if d= 'a'. If this Uri-Query option is not present, the default value is 't'. Veillette, et al. Expires November 16, 2019 [Page 15] Internet-Draft CoMI May 2019 4.2.3. GET A request to read the values of a data node instance is sent with a CoAP GET message. An instance identifier is specified in the URI path prefixed with the example path /c. FORMAT: GET /c/instance-identifier 2.05 Content (Content-Format: application/yang-data+cbor) CBOR map of SID, instance-value The returned payload contains the CBOR encoding of the specified data node instance value. 4.2.3.1. GET Examples Using for example the current-datetime leaf from module ietf-system [RFC7317], a request is sent to retrieve the value of 'system- state/clock/current-datetime' specified in container system-state. The SID of 'system-state/clock/current-datetime' is 1723, encoded in base64 according to Section 2.2, yields a7. The response to the request returns the CBOR map with the key set to the SID of the requested data node (i.e. 1723) and the value encoded using a 'text string' as defined in [I-D.ietf-core-yang-cbor] section 6.4. REQ: GET example.com/c/a7 RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1723 : "2014-10-26T12:16:31Z" } The next example represents the retrieval of a YANG container. In this case, the CoMI client performs a GET request on the clock container (SID = 1721; base64: a5). The container returned is encoded using a CBOR map as specified by [I-D.ietf-core-yang-cbor] section 4.2. REQ: GET example.com/c/a5 RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1721 : { +2 : "2014-10-26T12:16:51Z", / current-datetime SID 1723 / +1 : "2014-10-21T03:00:00Z" / boot-datetime SID 1722 / } } Veillette, et al. Expires November 16, 2019 [Page 16] Internet-Draft CoMI May 2019 This example shows the retrieval of the /interfaces/interface YANG list accessed using SID 1533 (base64: X9). The return payload is encoded using a CBOR array as specified by [I-D.ietf-core-yang-cbor] section 4.4.1 containing 2 instances. REQ: GET example.com/c/X9 RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1533 : [ { +4 : "eth0", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type, (SID 1538) identity / / ethernetCsmacd (SID 1880) / +2 : true / enabled ( SID 1535) / }, { +4 : "eth1", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type, (SID 1538) identity / / ethernetCsmacd (SID 1880) / +2 : false / enabled ( SID 1535) / } ] } To retrieve a specific instance within the /interfaces/interface YANG list, the CoMI client adds the key of the targeted instance in its CoAP request using the 'k' URI-Query. The return payload containing the instance requested is encoded using a CBOR array as specified by [I-D.ietf-core-yang-cbor] section 4.4.1. REQ: GET example.com/c/X9?k="eth0" RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1533 : [ { +4 : "eth0", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type, (SID 1538) identity / / ethernetCsmacd (SID 1880) / +2 : true / enabled ( SID 1535) / } ] } Veillette, et al. Expires November 16, 2019 [Page 17] Internet-Draft CoMI May 2019 It is equally possible to select a leaf of a specific instance of a list. The example below requests the description leaf (SID=1534, base64: X-) within the interface list corresponding to the interface name "eth0". The returned value is encoded in CBOR based on the rules specified by [I-D.ietf-core-yang-cbor] section 6.4. REQ: GET example.com/c/X-?k="eth0" RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1534 : "Ethernet adaptor" } 4.2.4. FETCH The FETCH is used to retrieve multiple data node instance values. The FETCH request payload contains the list of instance identifier of the data node instances requested. The return response payload contains a list of data node instance values in the same order as requested. A CBOR null is returned for each data node requested by the client, not supported by the server or not currently instantiated. For compactness, indexes of the list instance identifiers returned by the FETCH response SHOULD be elided, only the SID is provided. In this case, the format of each entry within the CBOR array of the FETCH response is identical to the format as a GET response. FORMAT: FETCH /c (Content-Format: application/yang-identifiers+cbor) CBOR array of instance-identifier 2.05 Content (Content-Format: application/yang-instances+cbor) CBOR array of CBOR map of instance-identifier, instance-value 4.2.4.1. FETCH examples This example uses the current-datetime leaf from module ietf-system [RFC7317] and the interface list from module ietf-interfaces [RFC7223]. In this example the value of current-datetime (SID 1723) and the interface list (SID 1533) instance identified with name="eth0" are queried. Veillette, et al. Expires November 16, 2019 [Page 18] Internet-Draft CoMI May 2019 REQ: FETCH /c (Content-Format: application/yang-identifiers+cbor) [ 1723, / current-datetime (SID 1723) / [1533, "eth0"] / interface (SID 1533) with name = "eth0" / ] RES: 2.05 Content (Content-Format: application/yang-instances+cbor) [ { 1723 : "2014-10-26T12:16:31Z" / current-datetime (SID 1723) / }, { 1533 : { +4 : "eth0", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type (SID 1538), identity / / ethernetCsmacd (SID 1880) / +2 : true / enabled (SID 1535) / } } ] 4.3. Data Editing CoMI allows datastore contents to be created, modified and deleted using CoAP methods. 4.3.1. Data Ordering A CoMI server SHOULD preserve the relative order of all user-ordered list and leaf-list entries that are received in a single edit request. These YANG data node types are encoded as CBOR arrays so messages will preserve their order. 4.3.2. POST The CoAP POST operation is used in CoMI for creation of data node resources and the invocation of "ACTION" and "RPC" resources. Refer to Section 4.6 for details on "ACTION" and "RPC" resources. A request to create a data node resource is sent with a CoAP POST message. The URI specifies the data node to be instantiated at the exception of list instances. In this case, for compactness, the URI specifies the list for which an instance is created. Veillette, et al. Expires November 16, 2019 [Page 19] Internet-Draft CoMI May 2019 FORMAT: POST /c/ (Content-Format :application/yang-data+cbor) CBOR map of SID, instance-value 2.01 Created If the data node resource already exists, then the POST request MUST fail and a "4.09 Conflict" response code MUST be returned 4.3.2.1. Post example The example uses the interface list from module ietf-interfaces [RFC7223]. This example creates a new list instance within the interface list (SID = 1533): REQ: POST /c/X9 (Content-Format: application/yang-data+cbor) { 1533 : [ { +4 : "eth5", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type (SID 1538), identity / / ethernetCsmacd (SID 1880) / +2 : true / enabled (SID 1535) / } ] } RES: 2.01 Created 4.3.3. PUT A data node resource instance is created or replaced with the PUT method. A request to set the value of a data node instance is sent with a CoAP PUT message. FORMAT: PUT /c/ (Content-Format :application/yang-data+cbor) CBOR map of SID, instance-value 2.01 Created Veillette, et al. Expires November 16, 2019 [Page 20] Internet-Draft CoMI May 2019 4.3.3.1. PUT example The example uses the interface list from module ietf-interfaces [RFC7223]. Example updates the instance of the list interface (SID = 1533) with key name="eth0": REQ: PUT /c/X9?k="eth0" (Content-Format: application/yang-data+cbor) { 1533 : [ { +4 : "eth0", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type (SID 1538), identity / / ethernetCsmacd (SID 1880) / +2 : true / enabled (SID 1535) / } ] } RES: 2.04 Changed 4.3.4. iPATCH One or multiple data node instances are replaced with the idempotent CoAP iPATCH method [RFC8132]. There are no Uri-Query options for the iPATCH method. The processing of the iPATCH command is specified by Content-Format 'application/yang-instances+cbor'. In summary, if the CBOR patch payload contains a data node instance that is not present in the target, this instance is added. If the target contains the specified instance, the content of this instance is replaced with the value of the payload. A null value indicates the removal of an existing data node instance. FORMAT: iPATCH /c (Content-Format: application/yang-instances+cbor) CBOR array of CBOR map of instance-identifier, instance-value 2.04 Changed 4.3.4.1. iPATCH example In this example, a CoMI client requests the following operations: o Set "/system/ntp/enabled" (SID 1755) to true. Veillette, et al. Expires November 16, 2019 [Page 21] Internet-Draft CoMI May 2019 o Remove the server "tac.nrc.ca" from the"/system/ntp/server" (SID 1756) list. o Add/set the server "NTP Pool server 2" to the list "/system/ntp/ server" (SID 1756). REQ: iPATCH /c (Content-Format: application/yang-instances+cbor) [ { 1755 : true / enabled (SID 1755) / }, { [1756, "tac.nrc.ca"] : null / server (SID 1756) / }, { 1756 : { / server (SID 1756) / +3 : "tic.nrc.ca", / name (SID 1759) / +4 : true, / prefer (SID 1760) / +5 : { / udp (SID 1761) / +1 : "132.246.11.231" / address (SID 1762) / } } } ] RES: 2.04 Changed 4.3.5. DELETE A data node resource is deleted with the DELETE method. FORMAT: Delete /c/ 2.02 Deleted 4.3.5.1. DELETE example This example uses the interface list from module ietf-interfaces [RFC7223]. This example deletes an instance of the interface list (SID = 1533): REQ: DELETE /c/X9?k="eth0" RES: 2.02 Deleted Veillette, et al. Expires November 16, 2019 [Page 22] Internet-Draft CoMI May 2019 4.4. Full datastore access The methods GET, PUT, POST, and DELETE can be used to request, replace, create, and delete a whole datastore respectively. FORMAT: GET /c 2.05 Content (Content-Format: application/yang-data+cbor) CBOR map of SID, instance-value FORMAT: PUT /c (Content-Format: application/yang-data+cbor) CBOR map of SID, instance-value 2.04 Changed FORMAT: POST /c (Content-Format: application/yang-data+cbor) CBOR map of SID, instance-value 2.01 Created FORMAT: DELETE /c 2.02 Deleted The content of the CBOR map represents the complete datastore of the server at the GET indication of after a successful processing of a PUT or POST request. 4.4.1. Full datastore examples The example uses the interface list from module ietf-interfaces [RFC7223] and the clock container from module ietf-system [RFC7317]. We assume that the datastore contains two modules ietf-system (SID 1700) and ietf-interfaces (SID 1500); they contain the 'interface' list (SID 1533) with one instance and the 'clock' container (SID 1721). After invocation of GET, a CBOR map with data nodes from these two modules is returned: Veillette, et al. Expires November 16, 2019 [Page 23] Internet-Draft CoMI May 2019 REQ: GET /c RES: 2.05 Content (Content-Format: application/yang-data+cbor) { 1721 : { / Clock (SID 1721) / +2: "2016-10-26T12:16:31Z", / current-datetime (SID 1723) / +1: "2014-10-05T09:00:00Z" / boot-datetime (SID 1722) / }, 1533 : [ { / interface (SID 1533) / +4 : "eth0", / name (SID 1537) / +1 : "Ethernet adaptor", / description (SID 1534) / +5 : 1880, / type (SID 1538), identity: / / ethernetCsmacd (SID 1880) / +2 : true / enabled (SID 1535) / } ] } 4.5. Event stream Event notification is an essential function for the management of servers. CoMI allows notifications specified in YANG [RFC5277] to be reported to a list of clients. The recommended path of the default event stream is /s. The server MAY support additional event stream resources to address different notification needs. Reception of notification instances is enabled with the CoAP Observe [RFC7641] function. Clients subscribe to the notifications by sending a GET request with an "Observe" option, specifying the /s resource when the default stream is selected. Each response payload carries one or multiple notifications. The number of notifications reported, and the conditions used to remove notifications from the reported list is left to implementers. When multiple notifications are reported, they MUST be ordered starting from the newest notification at index zero. The format of notification contents is defined in [I-D.ietf-core-yang-cbor] section 4.2.1. For notification without any content, a null value is returned. An example implementation is: Every time an event is generated, the generated notification instance is appended to the chosen stream(s). After an aggregation period, which may be adjusted using an exclusion delay and limited by the maximum number of notifications supported, the Veillette, et al. Expires November 16, 2019 [Page 24] Internet-Draft CoMI May 2019 content of the instance is sent to all clients observing the modified stream. FORMAT: GET / Observe(0) 2.05 Content (Content-Format :application/yang-instances+cbor) CBOR array of CBOR map of instance-identifier, instance-value The array of data node instances may contain identical entries which have been generated at different times. 4.5.1. Notify Examples Let suppose the server generates the example-port-fault event as defined below. module example-port { ... notification example-port-fault { // SID 60010 description "Event generated if a hardware fault is detected"; leaf port-name { // SID 60011 type string; } leaf port-fault { // SID 60012 type string; } } } By executing a GET on the /s resource the client receives the following response: Veillette, et al. Expires November 16, 2019 [Page 25] Internet-Draft CoMI May 2019 REQ: GET /s Observe(0) Token(0x93) RES: 2.05 Content (Content-Format :application/yang-tree+cbor) Observe(12) Token(0x93) [ { 60010 : { / example-port-fault (SID 60010) / +1 : "0/4/21", / port-name (SID 60011) / +2 : "Open pin 2" / port-fault (SID 60012) / } }, { 60010 : { / example-port-fault (SID 60010) / +1 : "1/4/21", / port-name (SID 60011) / +2 : "Open pin 5" / port-fault (SID 60012) / } } ] In the example, the request returns a success response with the contents of the last two generated events. Consecutively the server will regularly notify the client when a new event is generated. To check that the client is still alive, the server MUST send Confirmable Message periodically. When the client does not confirm the notification from the server, the server will remove the client from the list of observers [RFC7641]. 4.5.2. The 'f' Uri-Query option The 'f' (filter) option is used to indicate which subset of all possible notifications is of interest. If not present, all events notifications supported by the event stream are reported. When not supported by a CoMI server, this option shall be ignored, all events notifications are reported independently of the presence and content of the 'f' (filter) option. When present, this option contains a comma separated list of notification SIDs. For example, the following request returns notifications 60010 and 60020. REQ: GET /s?f=60010,60020 Observe(0) Token(0x241) Veillette, et al. Expires November 16, 2019 [Page 26] Internet-Draft CoMI May 2019 4.6. RPC statements The YANG "action" and "RPC" statements specify the execution of a Remote procedure Call (RPC) in the server. It is invoked using a POST method to an "Action" or "RPC" resource instance. The request payload contains the values assigned to the input container when specified. The response payload contains the values of the output container when specified. Both the input and output containers are encoded in CBOR using the rules defined in [I-D.ietf-core-yang-cbor] section 4.2.1. The returned success response code is 2.05 Content. FORMAT: POST /c/ (Content-Format :application/yang-data+cbor) CBOR map of SID, instance-value 2.05 Content (Content-Format :application/yang-data+cbor) CBOR map of SID, instance-value 4.6.1. RPC Example The example is based on the YANG action reset as defined in [RFC7950] section 7.15.3 and annotated below with SIDs. Veillette, et al. Expires November 16, 2019 [Page 27] Internet-Draft CoMI May 2019 module example-server-farm { yang-version 1.1; namespace "urn:example:server-farm"; prefix "sfarm"; import ietf-yang-types { prefix "yang"; } list server { // SID 60000 key name; leaf name { // SID 60001 type string; } action reset { // SID 60002 input { leaf reset-at { // SID 60003 type yang:date-and-time; mandatory true; } } output { leaf reset-finished-at { // SID 60004 type yang:date-and-time; mandatory true; } } } } } This example invokes the 'reset' action (SID 60002, base64: Opq), of the server instance with name equal to "myserver". REQ: POST /c/Opq?k="myserver" (Content-Format :application/yang-data+cbor) { 60002 : { +1 : "2016-02-08T14:10:08Z09:00" / reset-at (SID 60003) / } } RES: 2.05 Content (Content-Format :application/yang-data+cbor) { 60002 : { +2 : "2016-02-08T14:10:08Z09:18" / reset-finished-at (SID 60004)/ } } Veillette, et al. Expires November 16, 2019 [Page 28] Internet-Draft CoMI May 2019 5. Use of Block The CoAP protocol provides reliability by acknowledging the UDP datagrams. However, when large pieces of data need to be transported, datagrams get fragmented, thus creating constraints on the resources in the client, server and intermediate routers. The block option [RFC7959] allows the transport of the total payload in individual blocks of which the size can be adapted to the underlying transport sizes such as: (UDP datagram size ~64KiB, IPv6 MTU of 1280, IEEE 802.15.4 payload of 60-80 bytes). Each block is individually acknowledged to guarantee reliability. Notice that the Block mechanism splits the data at fixed positions, such that individual data fields may become fragmented. Therefore, assembly of multiple blocks may be required to process the complete data field. Beware of race conditions. Blocks are filled one at a time and care should be taken that the whole data representation is sent in multiple blocks sequentially without interruption. On the server, values are changed, lists are re-ordered, extended or reduced. When these actions happen during the serialization of the contents of the resource, the transported results do not correspond with a state having occurred in the server; or worse the returned values are inconsistent. For example: array length does not correspond with the actual number of items. It may be advisable to use Indefinite-length CBOR arrays and maps, which are foreseen for data streaming purposes. 6. Application Discovery Two application discovery mechanisms are supported by CoMI, the YANG library data model as defined by [I-D.veillette-core-yang-library] and the CORE resource discovery [RFC6690]. Implementers may choose to implement one or the other or both. 6.1. YANG library The YANG library data model [I-D.veillette-core-yang-library] provides a high level description of the resources available. The YANG library contains the list of modules, features and deviations supported by the CoMI server. From this information, CoMI clients can infer the list of data nodes supported and the interaction model to be used to access them. This module also contains the list of datastores implemented. The location of the YANG library can be found by sending a GET request to "/.well-known/core" including a resource type (RT) Veillette, et al. Expires November 16, 2019 [Page 29] Internet-Draft CoMI May 2019 parameter with the value "core.c.yl". Upon success, the return payload will contain the root resource of the YANG library module. REQ: GET /.well-known/core?rt=core.c.yl RES: 2.05 Content (Content-Format: application/link-format) ;rt="core.c.yl" 6.2. Resource Discovery Even if the YANG library provides all the information needed for application discovery, the implementation of Resource discovery as defined by [RFC6690] can be desirable for a seamless integration with other CoAP interfaces and services. 6.2.1. Datastore Resource Discovery The presence and location of (path to) each datastore implemented by the CoMI server can be discovered by sending a GET request to "/.well-known/core" including a resource type (RT) parameter with the value "core.c.ds". Upon success, the return payload contains the list of datastore resources. Each datastore returned is further qualified using the "ds" Link- Format attribute. This attribute is set to the SID assigned to the datastore identity. When a unified datastore is implemented, the ds attribute is set to 1029. For other examples of datastores, see the Network Management Datastore Architecture (NMDA) [RFC7950]. link-extension = ( "ds" "=" sid ) ) ; SID assigned to the datastore identity sid = 1*DIGIT For example: REQ: GET /.well-known/core?rt=core.c.ds RES: 2.05 Content (Content-Format: application/link-format) ; rt="core.c.ds";ds= 1029 6.2.2. Data node Resource Discovery The presence and location of (path to) each data node implemented by the CoMI server are discovered by sending a GET request to "/.well- known/core" including a resource type (RT) parameter with the value "core.c.dn". Veillette, et al. Expires November 16, 2019 [Page 30] Internet-Draft CoMI May 2019 Upon success, the return payload contains the SID assigned to each data node and their location. The example below shows the discovery of the presence and location of data nodes. Data nodes '/ietf-system:system-state/clock/boot- datetime' (SID 1722) and '/ietf-system:system-state/clock/current- datetime' (SID 1723) are returned. REQ: GET /.well-known/core?rt=core.c.dn RES: 2.05 Content (Content-Format: application/link-format) ;rt="core.c.dn", ;rt="core.c.dn" The list of data nodes may become prohibitively long. Implementations MAY return a subset of this list or can rely solely on the YANG library. 6.2.3. Event stream Resource Discovery The presence and location of (path to) each event stream implemented by the CoMI server are discovered by sending a GET request to "/.well-known/core" including a resource type (RT) parameter with the value "core.c.es". Upon success, the return payload contains the list of event stream resources. For example: REQ: GET /.well-known/core?rt=core.c.es RES: 2.05 Content (Content-Format: application/link-format) ;rt="core.c.es" 7. Error Handling In case a request is received which cannot be processed properly, the CoMI server MUST return an error message. This error message MUST contain a CoAP 4.xx or 5.xx response code. Errors returned by a CoMI server can be broken into two categories, those associated to the CoAP protocol itself and those generated during the validation of the YANG data model constrains as described in [RFC7950] section 8. Veillette, et al. Expires November 16, 2019 [Page 31] Internet-Draft CoMI May 2019 The following list of common CoAP errors should be implemented by CoMI servers. This list is not exhaustive, other errors defined by CoAP and associated RFCs may be applicable. o Error 4.01 (Unauthorized) is returned by the CoMI server when the CoMI client is not authorized to perform the requested action on the targeted resource (i.e. data node, datastore, rpc, action or event stream). o Error 4.02 (Bad Option) is returned by the CoMI server when one or more CoAP options are unknown or malformed. o Error 4.04 (Not Found) is returned by the CoMI server when the CoMI client is requesting a non-instantiated resource (i.e. data node, datastore, rpc, action or event stream). o Error 4.05 (Method Not Allowed) is returned by the CoMI server when the CoMI client is requesting a method not supported on the targeted resource. (e.g. GET on an rpc, PUT or POST on a data node with "config" set to false). o Error 4.08 (Request Entity Incomplete) is returned by the CoMI server if one or multiple blocks of a block transfer request is missing, see [RFC7959] for more details. o Error 4.13 (Request Entity Too Large) may be returned by the CoMI server during a block transfer request, see [RFC7959] for more details. o Error 4.15 (Unsupported Content-Format) is returned by the CoMI server when the Content-Format used in the request don't match those specified in section Section 2.4. CoMI server MUST also enforce the different constraints associated to the YANG data models implemented. These constraints are described in [RFC7950] section 8. These errors are reported using the CoAP error code 4.00 (Bad Request) and may have the following error container as payload. The YANG definition and associated .sid file are available in Appendix A and Appendix B. The error container is encoded using the encoding rules of a YANG data template as defined in [I-D.ietf-core-yang-cbor] section 5. +--rw error! +--rw error-tag identityref +--rw error-app-tag? identityref +--rw error-data-node? instance-identifier +--rw error-message? string Veillette, et al. Expires November 16, 2019 [Page 32] Internet-Draft CoMI May 2019 The following 'error-tag' and 'error-app-tag' are defined by the ietf-comi YANG module, these tags are implemented as YANG identity and can be extended as needed. o error-tag 'operation-failed' is returned by the CoMI server when the operation request cannot be processed successfully. * error-app-tag 'malformed-message' is returned by the CoMI server when the payload received from the CoMI client don't contain a well-formed CBOR content as defined in [RFC7049] section 3.3 or don't comply with the CBOR structure defined within this document. * error-app-tag 'data-not-unique' is returned by the CoMI server when the validation of the 'unique' constraint of a list or leaf-list fails. * error-app-tag 'too-many-elements' is returned by the CoMI server when the validation of the 'max-elements' constraint of a list or leaf-list fails. * error-app-tag 'too-few-elements' is returned by the CoMI server when the validation of the 'min-elements' constraint of a list or leaf-list fails. * error-app-tag 'must-violation' is returned by the CoMI server when the restrictions imposed by a 'must' statement are violated. * error-app-tag 'duplicate' is returned by the CoMI server when a client tries to create a duplicate list or leaf-list entry. o error-tag 'invalid-value' is returned by the CoMI server when the CoMI client tries to update or create a leaf with a value encoded using an invalid CBOR datatype or if the 'range', 'length', 'pattern' or 'require-instance' constrain is not fulfilled. * error-app-tag 'invalid-datatype' is returned by the CoMI server when CBOR encoding don't follow the rules set by or when the value is incompatible with the YANG Built-In type. (e.g. a value greater than 127 for an int8, undefined enumeration) * error-app-tag 'not-in-range' is returned by the CoMI server when the validation of the 'range' property fails. * error-app-tag 'invalid-length' is returned by the CoMI server when the validation of the 'length' property fails. Veillette, et al. Expires November 16, 2019 [Page 33] Internet-Draft CoMI May 2019 * error-app-tag 'pattern-test-failed' is returned by the CoMI server when the validation of the 'pattern' property fails. o error-tag 'missing-element' is returned by the CoMI server when the operation requested by a CoMI client fail to comply with the 'mandatory' constraint defined. The 'mandatory' constraint is enforced for leafs and choices, unless the node or any of its ancestors have a 'when' condition or 'if-feature' expression that evaluates to 'false'. * error-app-tag 'missing-key' is returned by the CoMI server to further qualify a missing-element error. This error is returned when the CoMI client tries to create or list instance, without all the 'key' specified or when the CoMI client tries to delete a leaf listed as a 'key'. * error-app-tag 'missing-input-parameter' is returned by the CoMI server when the input parameters of an RPC or action are incomplete. o error-tag 'unknown-element' is returned by the CoMI server when the CoMI client tries to access a data node of a YANG module not supported, of a data node associated to an 'if-feature' expression evaluated to 'false' or to a 'when' condition evaluated to 'false'. o error-tag 'bad-element' is returned by the CoMI server when the CoMI client tries to create data nodes for more than one case in a choice. o error-tag 'data-missing' is returned by the CoMI server when a data node required to accept the request is not present. * error-app-tag 'instance-required' is returned by the CoMI server when a leaf of type 'instance-identifier' or 'leafref' marked with require-instance set to 'true' refers to an instance that does not exist. * error-app-tag 'missing-choice' is returned by the CoMI server when no nodes exist in a mandatory choice. o error-tag 'error' is returned by the CoMI server when an unspecified error has occurred. For example, the CoMI server might return the following error. Veillette, et al. Expires November 16, 2019 [Page 34] Internet-Draft CoMI May 2019 RES: 4.00 Bad Request (Content-Format :application/yang-data+cbor) { 1024 : { +4 : 1011, / error-tag (SID 1028) / / = invalid-value (SID 1011) / +1 : 1018, / error-app-tag (SID 1025) / / = not-in-range (SID 1018) / +2 : 1740, / error-data-node (SID 1026) / / = timezone-utc-offset (SID 1740) / +3 : "maximum value exceeded" / error-message (SID 1027) / } } 8. Security Considerations For secure network management, it is important to restrict access to configuration variables only to authorized parties. CoMI re-uses the security mechanisms already available to CoAP, this includes DTLS [RFC6347] for protected access to resources, as well suitable authentication and authorization mechanisms. Among the security decisions that need to be made are selecting security modes and encryption mechanisms (see [RFC7252]). This requires a trade-off, as the NoKey mode gives no protection at all, but is easy to implement, whereas the X.509 mode is quite secure, but may be too complex for constrained devices. In addition, mechanisms for authentication and authorization may need to be selected. CoMI avoids defining new security mechanisms as much as possible. However, some adaptations may still be required, to cater for CoMI's specific requirements. 9. IANA Considerations 9.1. Resource Type (rt=) Link Target Attribute Values Registry This document adds the following resource type to the "Resource Type (rt=) Link Target Attribute Values", within the "Constrained RESTful Environments (CoRE) Parameters" registry. Veillette, et al. Expires November 16, 2019 [Page 35] Internet-Draft CoMI May 2019 +-----------+---------------------+-----------+ | Value | Description | Reference | +-----------+---------------------+-----------+ | core.c.ds | YANG datastore | RFC XXXX | | | | | | core.c.dn | YANG data node | RFC XXXX | | | | | | core.c.yl | YANG module library | RFC XXXX | | | | | | core.c.es | YANG event stream | RFC XXXX | +-----------+---------------------+-----------+ // RFC Ed.: replace RFC XXXX with this RFC number and remove this note. 9.2. CoAP Content-Formats Registry This document adds the following Content-Format to the "CoAP Content- Formats", within the "Constrained RESTful Environments (CoRE) Parameters" registry. +-----------------------------------+-------------+-----------+ | Media Type | Encoding ID | Reference | +-----------------------------------+-------------+-----------+ | application/yang-data+cbor | XXX | RFC XXXX | | | | | | application/yang-identifiers+cbor | XXX | RFC XXXX | | | | | | application/yang-instances+cbor | XXX | RFC XXXX | +-----------------------------------+-------------+-----------+ // RFC Ed.: replace XXX with assigned IDs and remove this note. // RFC Ed.: replace RFC XXXX with this RFC number and remove this note. 9.3. Media Types Registry This document adds the following media types to the "Media Types" registry. Veillette, et al. Expires November 16, 2019 [Page 36] Internet-Draft CoMI May 2019 +-----------------------+----------------------------+-----------+ | Name | Template | Reference | +-----------------------+----------------------------+-----------+ | yang-data+cbor | application/yang-data+cbor | RFC XXXX | | | | | | yang-identifiers+cbor | application/ | RFC XXXX | | | | | | | yang-identifiers+cbor | | | | | | | yang-instances+cbor | application/ | RFC XXXX | | | | | | | yang-instances+cbor | | +-----------------------+----------------------------+-----------+ Each of these media types share the following information: o Subtype name: o Required parameters: N/A o Optional parameters: N/A o Encoding considerations: binary o Security considerations: See the Security Considerations section of RFC XXXX o Interoperability considerations: N/A o Published specification: RFC XXXX o Applications that use this media type: CoMI o Fragment identifier considerations: N/A o Additional information: * Deprecated alias names for this type: N/A * Magic number(s): N/A * File extension(s): N/A * Macintosh file type code(s): N/A o Person & email address to contact for further information: iesg&ietf.org Veillette, et al. Expires November 16, 2019 [Page 37] Internet-Draft CoMI May 2019 o Intended usage: COMMON o Restrictions on usage: N/A o Author: Michel Veillette, ietf&augustcellars.com o Change Controller: IESG o Provisional registration? No // RFC Ed.: replace RFC XXXX with this RFC number and remove this note. 10. Acknowledgements We are very grateful to Bert Greevenbosch who was one of the original authors of the CoMI specification. Mehmet Ersue and Bert Wijnen explained the encoding aspects of PDUs transported under SNMP. Carsten Bormann has given feedback on the use of CBOR. The draft has benefited from comments (alphabetical order) by Rodney Cummings, Dee Denteneer, Esko Dijk, Michael van Hartskamp, Tanguy Ropitault, Juergen Schoenwaelder, Anuj Sehgal, Zach Shelby, Hannes Tschofenig, Michael Verschoor, and Thomas Watteyne. 11. References 11.1. Normative References [I-D.ietf-core-sid] Veillette, M., Pelov, A., and I. Petrov, "YANG Schema Item iDentifier (SID)", draft-ietf-core-sid-06 (work in progress), March 2019. [I-D.ietf-core-yang-cbor] Veillette, M., Petrov, I., and A. Pelov, "CBOR Encoding of Data Modeled with YANG", draft-ietf-core-yang-cbor-10 (work in progress), April 2019. [I-D.veillette-core-yang-library] Veillette, M. and I. Petrov, "Constrained YANG Module Library", draft-veillette-core-yang-library-04 (work in progress), March 2019. Veillette, et al. Expires November 16, 2019 [Page 38] Internet-Draft CoMI May 2019 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, DOI 10.17487/RFC4648, October 2006, . [RFC5277] Chisholm, S. and H. Trevino, "NETCONF Event Notifications", RFC 5277, DOI 10.17487/RFC5277, July 2008, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6243] Bierman, A. and B. Lengyel, "With-defaults Capability for NETCONF", RFC 6243, DOI 10.17487/RFC6243, June 2011, . [RFC7049] Bormann, C. and P. Hoffman, "Concise Binary Object Representation (CBOR)", RFC 7049, DOI 10.17487/RFC7049, October 2013, . [RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained Application Protocol (CoAP)", RFC 7252, DOI 10.17487/RFC7252, June 2014, . [RFC7641] Hartke, K., "Observing Resources in the Constrained Application Protocol (CoAP)", RFC 7641, DOI 10.17487/RFC7641, September 2015, . [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, . [RFC7959] Bormann, C. and Z. Shelby, Ed., "Block-Wise Transfers in the Constrained Application Protocol (CoAP)", RFC 7959, DOI 10.17487/RFC7959, August 2016, . [RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017, . Veillette, et al. Expires November 16, 2019 [Page 39] Internet-Draft CoMI May 2019 [RFC8132] van der Stok, P., Bormann, C., and A. Sehgal, "PATCH and FETCH Methods for the Constrained Application Protocol (CoAP)", RFC 8132, DOI 10.17487/RFC8132, April 2017, . 11.2. Informative References [RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347, January 2012, . [RFC6690] Shelby, Z., "Constrained RESTful Environments (CoRE) Link Format", RFC 6690, DOI 10.17487/RFC6690, August 2012, . [RFC7223] Bjorklund, M., "A YANG Data Model for Interface Management", RFC 7223, DOI 10.17487/RFC7223, May 2014, . [RFC7317] Bierman, A. and M. Bjorklund, "A YANG Data Model for System Management", RFC 7317, DOI 10.17487/RFC7317, August 2014, . [RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018, . Appendix A. ietf-comi YANG module file "ietf-comi@2019-03-28.yang" module ietf-comi { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-comi"; prefix comi; import ietf-datastores { prefix ds; } import ietf-restconf { prefix rc; description "This import statement is required to access the yang-data extension defined in RFC 8040."; reference "RFC 8040: RESTCONF Protocol"; } Veillette, et al. Expires November 16, 2019 [Page 40] Internet-Draft CoMI May 2019 organization "IETF Core Working Group"; contact "Michel Veillette Alexander Pelov Peter van der Stok Andy Bierman "; description "This module contains the different definitions required by the CoMI protocol."; revision 2019-03-28 { description "Initial revision."; reference "[I-D.ietf-core-comi] CoAP Management Interface"; } identity unified { base ds:datastore; description "Identifier of the unified configuration and operational state datastore."; } identity error-tag { description "Base identity for error-tag."; } identity operation-failed { base error-tag; description "Returned by the CoMI server when the operation request can't be processed successfully."; } identity invalid-value { base error-tag; Veillette, et al. Expires November 16, 2019 [Page 41] Internet-Draft CoMI May 2019 description "Returned by the CoMI server when the CoMI client tries to update or create a leaf with a value encoded using an invalid CBOR datatype or if the 'range', 'length', 'pattern' or 'require-instance' constrain is not fulfilled."; } identity missing-element { base error-tag; description "Returned by the CoMI server when the operation requested by a CoMI client fails to comply with the 'mandatory' constraint defined. The 'mandatory' constraint is enforced for leafs and choices, unless the node or any of its ancestors have a 'when' condition or 'if-feature' expression that evaluates to 'false'."; } identity unknown-element { base error-tag; description "Returned by the CoMI server when the CoMI client tries to access a data node of a YANG module not supported, of a data node associated with an 'if-feature' expression evaluated to 'false' or to a 'when' condition evaluated to 'false'."; } identity bad-element { base error-tag; description "Returned by the CoMI server when the CoMI client tries to create data nodes for more than one case in a choice."; } identity data-missing { base error-tag; description "Returned by the CoMI server when a data node required to accept the request is not present."; } identity error { base error-tag; description "Returned by the CoMI server when an unspecified error has occurred."; Veillette, et al. Expires November 16, 2019 [Page 42] Internet-Draft CoMI May 2019 } identity error-app-tag { description "Base identity for error-app-tag."; } identity malformed-message { base error-app-tag; description "Returned by the CoMI server when the payload received from the CoMI client don't contain a well-formed CBOR content as defined in [RFC7049] section 3.3 or don't comply with the CBOR structure defined within this document."; } identity data-not-unique { base error-app-tag; description "Returned by the CoMI server when the validation of the 'unique' constraint of a list or leaf-list fails."; } identity too-many-elements { base error-app-tag; description "Returned by the CoMI server when the validation of the 'max-elements' constraint of a list or leaf-list fails."; } identity too-few-elements { base error-app-tag; description "Returned by the CoMI server when the validation of the 'min-elements' constraint of a list or leaf-list fails."; } identity must-violation { base error-app-tag; description "Returned by the CoMI server when the restrictions imposed by a 'must' statement are violated."; } identity duplicate { base error-app-tag; description Veillette, et al. Expires November 16, 2019 [Page 43] Internet-Draft CoMI May 2019 "Returned by the CoMI server when a client tries to create a duplicate list or leaf-list entry."; } identity invalid-datatype { base error-app-tag; description "Returned by the CoMI server when CBOR encoding is incorect or when the value encoded is incompatible with the YANG Built-In type. (e.g. value greater than 127 for an int8, undefined enumeration)."; } identity not-in-range { base error-app-tag; description "Returned by the CoMI server when the validation of the 'range' property fails."; } identity invalid-length { base error-app-tag; description "Returned by the CoMI server when the validation of the 'length' property fails."; } identity pattern-test-failed { base error-app-tag; description "Returned by the CoMI server when the validation of the 'pattern' property fails."; } identity missing-key { base error-app-tag; description "Returned by the CoMI server to further qualify a missing-element error. This error is returned when the CoMI client tries to create or list instance, without all the 'key' specified or when the CoMI client tries to delete a leaf listed as a 'key'."; } identity missing-input-parameter { base error-app-tag; description "Returned by the CoMI server when the input parameters Veillette, et al. Expires November 16, 2019 [Page 44] Internet-Draft CoMI May 2019 of a RPC or action are incomplete."; } identity instance-required { base error-app-tag; description "Returned by the CoMI server when a leaf of type 'instance-identifier' or 'leafref' marked with require-instance set to 'true' refers to an instance that does not exist."; } identity missing-choice { base error-app-tag; description "Returned by the CoMI server when no nodes exist in a mandatory choice."; } rc:yang-data comi-error { container error { description "Optional payload of a 4.00 Bad Request CoAP error."; leaf error-tag { type identityref { base error-tag; } mandatory true; description "The enumerated error-tag."; } leaf error-app-tag { type identityref { base error-app-tag; } description "The application-specific error-tag."; } leaf error-data-node { type instance-identifier; description "When the error reported is caused by a specific data node, this leaf identifies the data node in error."; } Veillette, et al. Expires November 16, 2019 [Page 45] Internet-Draft CoMI May 2019 leaf error-message { type string; description "A message describing the error."; } } } } Appendix B. ietf-comi .sid file { "assignment-ranges": [ { "entry-point": 1000, "size": 100 } ], "module-name": "ietf-comi", "module-revision": "2019-03-28", "items": [ { "namespace": "module", "identifier": "ietf-comi", "sid": 1000 }, { "namespace": "identity", "identifier": "bad-element", "sid": 1001 }, { "namespace": "identity", "identifier": "data-missing", "sid": 1002 }, { "namespace": "identity", "identifier": "data-not-unique", "sid": 1003 }, { "namespace": "identity", "identifier": "duplicate", "sid": 1004 }, { Veillette, et al. Expires November 16, 2019 [Page 46] Internet-Draft CoMI May 2019 "namespace": "identity", "identifier": "error", "sid": 1005 }, { "namespace": "identity", "identifier": "error-app-tag", "sid": 1006 }, { "namespace": "identity", "identifier": "error-tag", "sid": 1007 }, { "namespace": "identity", "identifier": "instance-required", "sid": 1008 }, { "namespace": "identity", "identifier": "invalid-datatype", "sid": 1009 }, { "namespace": "identity", "identifier": "invalid-length", "sid": 1010 }, { "namespace": "identity", "identifier": "invalid-value", "sid": 1011 }, { "namespace": "identity", "identifier": "malformed-message", "sid": 1012 }, { "namespace": "identity", "identifier": "missing-choice", "sid": 1013 }, { "namespace": "identity", "identifier": "missing-element", "sid": 1014 Veillette, et al. Expires November 16, 2019 [Page 47] Internet-Draft CoMI May 2019 }, { "namespace": "identity", "identifier": "missing-input-parameter", "sid": 1015 }, { "namespace": "identity", "identifier": "missing-key", "sid": 1016 }, { "namespace": "identity", "identifier": "must-violation", "sid": 1017 }, { "namespace": "identity", "identifier": "not-in-range", "sid": 1018 }, { "namespace": "identity", "identifier": "operation-failed", "sid": 1019 }, { "namespace": "identity", "identifier": "pattern-test-failed", "sid": 1020 }, { "namespace": "identity", "identifier": "too-few-elements", "sid": 1021 }, { "namespace": "identity", "identifier": "too-many-elements", "sid": 1022 }, { "namespace": "identity", "identifier": "unified", "sid": 1029 }, { "namespace": "identity", Veillette, et al. Expires November 16, 2019 [Page 48] Internet-Draft CoMI May 2019 "identifier": "unknown-element", "sid": 1023 }, { "namespace": "data", "identifier": "/ietf-comi:error", "sid": 1024 }, { "namespace": "data", "identifier": "/ietf-comi:error/error-app-tag", "sid": 1025 }, { "namespace": "data", "identifier": "/ietf-comi:error/error-data-node", "sid": 1026 }, { "namespace": "data", "identifier": "/ietf-comi:error/error-message", "sid": 1027 }, { "namespace": "data", "identifier": "/ietf-comi:error/error-tag", "sid": 1028 } ] } Authors' Addresses Michel Veillette (editor) Trilliant Networks Inc. 610 Rue du Luxembourg Granby, Quebec J2J 2V2 Canada Email: michel.veillette@trilliant.com Peter van der Stok (editor) consultant Phone: +31-492474673 (Netherlands), +33-966015248 (France) Email: consultancy@vanderstok.org URI: www.vanderstok.org Veillette, et al. Expires November 16, 2019 [Page 49] Internet-Draft CoMI May 2019 Alexander Pelov Acklio 2bis rue de la Chataigneraie Cesson-Sevigne, Bretagne 35510 France Email: a@ackl.io Andy Bierman YumaWorks 685 Cochran St. Suite #160 Simi Valley, CA 93065 USA Email: andy@yumaworks.com Veillette, et al. Expires November 16, 2019 [Page 50]