ACE Working Group F. Palombini Internet-Draft Ericsson Intended status: Standards Track C. Sengul Expires: 1 January 2022 Brunel University 30 June 2021 Pub-Sub Profile for Authentication and Authorization for Constrained Environments (ACE) draft-ietf-ace-pubsub-profile-03 Abstract This specification defines an application profile for authentication and authorization for publishers and subscribers in a constrained pub-sub scenario, using the ACE framework. This profile relies on transport layer or application layer security to authorize the pub- sub clients to the broker. Moreover, it describes application layer security for publisher-subscriber communication going through the broker. Note to Readers Source for this draft and an issue tracker can be found at https://github.com/ace-wg/pubsub-profile (https://github.com/ace-wg/ pubsub-profile). Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 1 January 2022. Copyright Notice Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. Palombini & Sengul Expires 1 January 2022 [Page 1] Internet-Draft pubsub-profile June 2021 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 2. Application Profile Overview . . . . . . . . . . . . . . . . 3 3. PubSub Authorisation . . . . . . . . . . . . . . . . . . . . 5 3.1. AS Discovery (Optional) . . . . . . . . . . . . . . . . . 6 3.2. Authorising to the Broker . . . . . . . . . . . . . . . . 6 4. Key Distribution for PubSub Content Protection . . . . . . . 7 4.1. Token POST . . . . . . . . . . . . . . . . . . . . . . . 7 4.2. Join Request . . . . . . . . . . . . . . . . . . . . . . 8 5. PubSub Protected Communication . . . . . . . . . . . . . . . 11 5.1. Using COSE Objects To Protect The Resource Representation . . . . . . . . . . . . . . . . . . . . . 12 6. Profile-specific Considerations . . . . . . . . . . . . . . . 13 6.1. CoAP PubSub Application Profile . . . . . . . . . . . . . 13 6.2. MQTT PubSub Application Profile . . . . . . . . . . . . . 14 7. Security Considerations . . . . . . . . . . . . . . . . . . . 15 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16 8.1. ACE Groupcomm Profile Registry . . . . . . . . . . . . . 16 8.1.1. CoAP Profile Registration . . . . . . . . . . . . . . 16 8.1.2. MQTT Profile Registration . . . . . . . . . . . . . . 17 8.2. ACE Groupcomm Key Registry . . . . . . . . . . . . . . . 17 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 17 9.1. Normative References . . . . . . . . . . . . . . . . . . 17 9.2. Informative References . . . . . . . . . . . . . . . . . 18 Appendix A. Requirements on Application Profiles . . . . . . . . 19 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 21 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 21 1. Introduction In the publish-subscribe (pub-sub) scenario, devices with limited reachability communicate via a broker, which enables store-and- forward messaging between the devices. This document defines a way to authorize pub-sub clients using the ACE framework [I-D.ietf-ace-oauth-authz], and to provide the keys for protecting the communication between them. The pub-sub communication using the Constrained Application Protocol (CoAP) is specified in Palombini & Sengul Expires 1 January 2022 [Page 2] Internet-Draft pubsub-profile June 2021 [I-D.ietf-core-coap-pubsub], while the one using MQTT is specified in [MQTT-OASIS-Standard-v5]. This document gives detailed specifications for MQTT and CoAP pub-sub, but can easily be adapted for other transport protocols as well. 1.1. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Readers are expected to be familiar with the terms and concepts described in [I-D.ietf-ace-oauth-authz], [I-D.ietf-ace-key-groupcomm]. In particular, analogously to [I-D.ietf-ace-oauth-authz], terminology for entities in the architecture such as Client (C), Resource Server (RS), and Authorization Server (AS) is defined in OAuth 2.0 [RFC6749] and [I-D.ietf-ace-actors], and terminology for entities such as the Key Distribution Center (KDC) and Dispatcher in [I-D.ietf-ace-key-groupcomm]. Readers are expected to be familiar with terms and concepts of pub- sub group communication, as described in [I-D.ietf-core-coap-pubsub], or MQTT [MQTT-OASIS-Standard-v5]. 2. Application Profile Overview The objective of this document is to specify how to authorize nodes, provide keys, and protect a pub-sub communication, using [I-D.ietf-ace-key-groupcomm], which expands from the ACE framework ([I-D.ietf-ace-oauth-authz]), and transport profiles ([I-D.ietf-ace-dtls-authorize], [I-D.ietf-ace-oscore-profile], [I-D.ietf-ace-mqtt-tls-profile]). The pub-sub communication protocol can be based on CoAP, as described in [I-D.ietf-core-coap-pubsub], MQTT [MQTT-OASIS-Standard-v5] , or other transport. Note that both publishers and subscribers use the same profiles. The architecture of the scenario is shown in Figure 1. Palombini & Sengul Expires 1 January 2022 [Page 3] Internet-Draft pubsub-profile June 2021 +----------------+ +----------------+ | | | Key | | Authorization | | Distribution | | Server | | Center | | (AS) | | (KDC) | +----------------+ +----------------+ ^ ^ | | +---------(A)----+ | | +--------------------(B)--------+ v v +------------+ +------------+ | | | | | Pub-Sub | <-- (C)---> | Broker | | Client | | | | | | | +------------+ +------------+ Figure 1: Architecture for Pub-Sub with Authorization Servers Publisher or Subscriber Clients is referred to as Client in short. This profile specifies: 1. The establishment of a secure connection between a Client and Broker, using an ACE transport profile such as DTLS [I-D.ietf-ace-dtls-authorize], OSCORE [I-D.ietf-ace-oscore-profile], or MQTT-TLS [I-D.ietf-ace-mqtt-tls-profile] (A and C). 2. The Clients retrieval of keying material for the Publisher Client to publish protected publications to the Broker, and for the Subscriber Client to read protected publications (B). These exchanges aim at setting up two different security associations. On the one hand, the Publisher and the Subscriber clients have a security association with the Broker (i.e. RS), so that RS can authorize the Clients (Security Association 1). On the other hand, the Publisher has a security association with the Subscriber, to protect the publication content (Security Association 2) while sending it through the broker (i.e. here, the broker corresponds to the Dispatcher in [I-D.ietf-ace-key-groupcomm]). The Security Association 1 is set up using AS and a transport profile of [I-D.ietf-ace-oauth-authz], the Security Association 2 is set up using AS, KDC and [I-D.ietf-ace-key-groupcomm]. Note that, given that the publication content is protected, the Broker MAY accept unauthorised Subscribers. In this case, the Subscriber client can skip setting up Security Association 1 with the Broker. Palombini & Sengul Expires 1 January 2022 [Page 4] Internet-Draft pubsub-profile June 2021 +------------+ +------------+ +------------+ | | | | | | | Publisher | | Broker | | Subscriber | | | | | | | | | | | | | +------------+ +------------+ +------------+ : : : : : : : '------ Security -------' '-----------------------' : : Association 1 : '------------------------------- Security --------------' Association 2 Figure 2: Security Associations between Publisher, Broker, Subscriber pairs. 3. PubSub Authorisation Since [I-D.ietf-ace-oauth-authz] recommends the use of CoAP and CBOR, this document describes the exchanges assuming CoAP and CBOR are used. However, using HTTP instead of CoAP is possible, using the corresponding parameters and methods. Analogously, JSON [RFC8259] can be used instead of CBOR, using the conversion method specified in Sections 6.1 and 6.2 of [RFC8949]. In case JSON is used, the Content Format or Media Type of the message has to be changed accordingly. Exact definition of these exchanges are considered out of scope for this document. Figure 3 shows the message flow for authorisation purposes. Client Broker AS KDC | [--Resource Request (CoAP/MQTT/other)-->] | | | | | | | | [<----AS Information (CoAP/MQTT/other)--] | | | | | | | ----- Authorisation Request (CoAP/HTTP/other)---->| | | | | | <------Authorisation Response (CoAP/HTTP/other) --| | | | |----------------------Token Post (CoAP)------------------->| | | |------------------- Joining Request (CoAP) --------------->| | | |------------------ Joining Response (CoAP) --------------->| Figure 3: Authorisation Flow Palombini & Sengul Expires 1 January 2022 [Page 5] Internet-Draft pubsub-profile June 2021 3.1. AS Discovery (Optional) Complementary to what is defined in [I-D.ietf-ace-oauth-authz] (Section 5.1) for AS discovery, the Broker MAY send the address of the AS to the Client in the 'AS' parameter in the AS Information as a response to an Unauthorized Resource Request (Section 5.2). An example using CBOR diagnostic notation and CoAP is given below: 4.01 Unauthorized Content-Format: application/ace+cbor {"AS": "coaps://as.example.com/token"} Figure 4: AS Information example Authorisation Server (AS) Discovery is also defined in Section 2.2.6.1 of [I-D.ietf-ace-mqtt-tls-profile] for MQTT v5 clients (and not supported for MQTT v3 clients). 3.2. Authorising to the Broker After retrieving the AS address, the Client sends an Authorisation Request to the AS for the KDC and the Broker. Note that the AS authorises: 1. What endpoints are allowed to Publish or Subscribe to the Broker. 2. What endpoints are allowed to access to which topic(s). The request includes the following fields from the Authorization Request (Section 3.1 of [I-D.ietf-ace-key-groupcomm]): * 'scope', containing the topic identifier, that the Client wishes to access * 'audience', an array with identifiers of the KDC and the Broker. Other additional parameters can be included if necessary, as defined in [I-D.ietf-ace-oauth-authz]. The 'scope' parameter is encoded as follows, where 'gname' is treated as topic identifier or filter. Palombini & Sengul Expires 1 January 2022 [Page 6] Internet-Draft pubsub-profile June 2021 gname = tstr role = tstr scope_entry = [ gname , ? ( role / [ 2*role ] ) ] scope = << [ + scope_entry ] >> Figure 5: CDLL definition of scope, using as example group name encoded as tstr and role as tstr. Other scope representations are also possible and are described in (Section 3.1 of [I-D.ietf-ace-key-groupcomm]). Note that in the AIF- MQTT data model is described in Section 3 of the [I-D.ietf-ace-mqtt-tls-profile], the role values have been further constrained to "pub" and "sub". The AS responds with an Authorization Response as defined in Section 5.8.2 of [I-D.ietf-ace-oauth-authz] and Section 3.2 of [I-D.ietf-ace-key-groupcomm]. If a token is returned, then the audience of this token are the KDC and the Broker, and the client uses the same token for both. In case CoAP PubSub is used as communication protocol, 'profile' is set to "coap_pubsub_app" as defined in Section 8.1.1. In case MQTT PubSub is used as communication protocol, 'profile' is set to "mqtt_pubsub_app" as defined in Section 8.1.2. 4. Key Distribution for PubSub Content Protection 4.1. Token POST After receiving a token from the AS, the Client posts the token to the KDC (Section 3.3 [I-D.ietf-ace-key-groupcomm]). In addition to the token post, a Subscriber Client MAY ask for the public keys in the group, used for source authentication, as well as any other group parameters. In this case, the message MUST have Content-Format set to "application/ace+cbor" defined in Section 8.16 of [I-D.ietf-ace-oauth-authz]. The message payload MUST be formatted as a CBOR map, which MUST include the access token and the 'sign_info' parameter. The details for the 'sign_info' parameter can be found in Section 3.3 of [I-D.ietf-ace-key-groupcomm]. Alternatively, the joining node may retrieve this information by other means as described in [I-D.ietf-ace-key-groupcomm]. Palombini & Sengul Expires 1 January 2022 [Page 7] Internet-Draft pubsub-profile June 2021 The KDC verifies that the Client is authorized to access the topic with the requested role. After successful verification, the Client is authorized to receive the group keying material from the KDC and join the group. The KDC replies to the Client with a 2.01 (Created) response, using Content-Format "application/ace+cbor". The payload of the 2.01 response is a CBOR map. A Publisher Client MUST send its own public key to the KDC when joining the group. Since the access token from a Publisher Client will have "pub" role, the KDC MUST include 'kdcchallenge' in the CBOR map, specifying a dedicated challenge N_S generated by the KDC. The Client uses this challenge to prove possession of its own private key (see [I-D.ietf-ace-key-groupcomm] for details). 4.2. Join Request In the next step, a joining node MUST have a secure communication association established with the KDC, before starting to join a group under that KDC. Possible ways to provide a secure communication association are described in the DTLS transport profile [I-D.ietf-ace-dtls-authorize] and OSCORE transport profile [I-D.ietf-ace-oscore-profile] of ACE. After establishing a secure communication, the Client sends a Joining Request to the KDC as described in Section 4.3 of [I-D.ietf-ace-key-groupcomm]. More specifically, the Client sends a POST request to the /ace-group/GROUPNAME endpoint on KDC, with Content-Format = "application/ace+cbor" that MUST contain in the payload (formatted as a CBOR map, Section 4.1.2.1 of [I-D.ietf-ace-key-groupcomm]): * 'scope' parameter as defined earlier * 'get_pub_keys' parameter set to the empty array if the Client needs to retrieve the public keys of the other pubsub members, * 'client_cred' parameter containing the Client's public key formatted as a COSE_Key (as defined in Section 8.2), if the Client is a Publisher, * 'cnonce', encoded as a CBOR byte string, and including a dedicated nonce N_C generated by the Client, if 'client_cred' is present, * 'client_cred_verify', set to a singature computed over the 'rsnonce' concatenated with cnonce, if 'client_cred' is present, * OPTIONALLY, if needed, the 'pub_keys_repos' parameter Palombini & Sengul Expires 1 January 2022 [Page 8] Internet-Draft pubsub-profile June 2021 TODO: Check 'cnonce' Note that for a Subscriber-only Client, the Joining Request MUST NOT contain the 'client_cred parameter', the role element in the 'scope' parameter MUST be set to "sub". The Subscriber MUST have access to the public keys of all the Publishers; this MAY be achieved in the Joining Request by using the parameter 'get_pub_keys' set to receive the public key of all Publishers using "pub" as the 'role_filter' (as described in Section 4.1.2.1 of [I-D.ietf-ace-key-groupcomm]). If the 'client_cred' parameter is present, KDC stores the public key of the Client. Note that the alg parameter in the 'client_cred' COSE_Key MUST be a signing algorithm, as defined in section 8 of [RFC8152], and that it is the same algorithm used to compute the signature sent in 'client_cred_verify'. The KDC response to Joining Response has the Content-Format = "application/ace+cbor". The payload (formatted as a CBOR map) MUST contain the following fields from the Joining Response (Section 4.2 of [I-D.ietf-ace-key-groupcomm]): * 'kty' identifies a key type "COSE_Key". * 'key', which contains a "COSE_Key" object (defined in [RFC8152], containing: - 'kty' with value 4 (symmetric) - 'alg' with value defined by the AS2 (Content Encryption Algorithm) - 'Base IV' with value defined by the AS2 - 'k' with value the symmetric key value - OPTIONALLY, 'kid' with an identifier for the key value * OPTIONALLY, 'exp' with the expiration time of the key * 'pub_keys', containing the public keys of all authorized signing members formatted as COSE_Keys, if the 'get_pub_keys' parameter was present and set to the empty array in the Key Distribution Request. For Subscriber Clients, the Joining Response MUST contain the 'pub_keys' parameter. Palombini & Sengul Expires 1 January 2022 [Page 9] Internet-Draft pubsub-profile June 2021 An example of the Joining Request and corresponding Response for a CoAP Publisher using CoAP and CBOR is specified in Figure 6 and Figure 7, where SIG is a signature computed using the private key associated to the public key and the algorithm in 'client_cred'. { "scope" : ["Broker1/Temp", "pub"], "client_cred" : { / COSE_Key / / type / 1 : 2, / EC2 / / kid / 2 : h'11', / alg / 3 : -7, / ECDSA with SHA-256 / / crv / -1 : 1 , / P-256 / / x / -2 : h'65eda5a12577c2bae829437fe338701a10aaa375e1bb5b5de1 08de439c08551d', / y /-3 : h'1e52ed75701163f7f9e40ddf9f341b3dc9ba860af7e0ca7ca7e 9eecd0084d19c', "cnonce" : h'd36b581d1eef9c7c, "client_cred_verify" : SIG } } Figure 6: Joining Request payload for a Publisher { "kty" : "COSE_Key", "key" : {1: 4, 2: h'1234', 3: 12, 5: h'1f389d14d17dc7', -1: h'02e2cc3a9b92855220f255fff1c615bc'} } Figure 7: Joining Response payload for a Publisher An example of the payload of a Joining Request and corresponding Response for a Subscriber using CoAP and CBOR is specified in Figure 8 and Figure 9. { "scope" : ["Broker1/Temp", "sub"], "get_pub_keys" : [true, ["pub"], []] } Figure 8: Joining Request payload for a Subscriber Palombini & Sengul Expires 1 January 2022 [Page 10] Internet-Draft pubsub-profile June 2021 { "scope" : ["Broker1/Temp", "sub"], "kty" : "COSE_Key" "key" : {1: 4, 2: h'1234', 3: 12, 5: h'1f389d14d17dc7', -1: h'02e2cc3a9b92855220f255fff1c615bc'}, "pub_keys" : [ { 1 : 2, / type EC2 / 2 : h'11', / kid / 3 : -7, / alg ECDSA with SHA-256 / -1 : 1 , / crv P-256 / -2 : h'65eda5a12577c2bae829437fe338701a10aaa375e1bb5b5de108de43 9c08551d', / x / -3 : h'1e52ed75701163f7f9e40ddf9f341b3dc9ba860af7e0ca7ca7e9eecd 0084d19c' / y / } ] } Figure 9: Joining Response payload for a Subscriber 5. PubSub Protected Communication +------------+ +------------+ +------------+ | | | | | | | Publisher | ----(D)---> | Broker | | Subscriber | | | | | <----(E)---- | | | | | | -----(F)---> | | +------------+ +------------+ +------------+ Figure 10: Secure communication between Publisher and Subscriber (D) corresponds to the publication of a topic on the Broker. The publication (the resource representation) is protected with COSE ([RFC8152]). The (E) message is the subscription of the Subscriber. The subscription MAY be unprotected. The (F) message is the response from the Broker, where the publication is protected with COSE. Publisher Broker Subscriber | --- PUT /topic ----> | | | protected with COSE | | | | <--- GET /topic ----- | | | | | | ---- response ------> | | | protected with COSE | Figure 11: (E), (F), (G): Example of protected communication for CoAP Palombini & Sengul Expires 1 January 2022 [Page 11] Internet-Draft pubsub-profile June 2021 The flow graph is presented below for CoAP. The message flow is similar for MQTT, where PUT corresponds to a PUBLISH message, and GET corresponds to a SUBSCRIBE message. Whenever a Client publishes a new message, the Broker sends this message to all valid subscribers. 5.1. Using COSE Objects To Protect The Resource Representation The Publisher uses the symmetric COSE Key received from the KDC (Section 4) to protect the payload of the PUBLISH operation (Section 4.3 of [I-D.ietf-core-coap-pubsub] and [MQTT-OASIS-Standard-v5]). Specifically, the COSE Key is used to create a COSE_Encrypt0 with algorithm specified by KDC. The Publisher uses the private key corresponding to the public key sent to the KDC in exchange B (Section 4) to countersign the COSE Object as specified in Section 4.5 of [RFC8152]. The payload is replaced by the COSE object before the publication is sent to the Broker. The Subscriber uses the 'kid' in the 'countersignature' field in the COSE object to retrieve the right public key to verify the countersignature. It then uses the symmetric key received from KDC to verify and decrypt the publication received in the payload from the Broker (in the case of CoAP the publication is received by the CoAP Notification and for MQTT, it is received as a PUBLISH message from the Broker to the subscribing client). The COSE object is constructed in the following way: * The protected Headers (as described in Section 3 of [RFC8152]) MAY contain the kid parameter, with value the kid of the symmetric COSE Key received in Section 4 and MUST contain the content encryption algorithm. * The unprotected Headers MUST contain the Partial IV, with value a sequence number that is incremented for every message sent, and the counter signature that includes: - the algorithm (same value as in the asymmetric COSE Key received in (B)) in the protected header; - the kid (same value as the kid of the asymmetric COSE Key received in (B)) in the unprotected header; - the signature computed as specified in Section 4.5 of [RFC8152]. * The ciphertext, computed over the plaintext that MUST contain the message payload. Palombini & Sengul Expires 1 January 2022 [Page 12] Internet-Draft pubsub-profile June 2021 The 'external_aad' is an empty string. An example is given in Figure 12: 16( [ / protected / h'a2010c04421234' / { \ alg \ 1:12, \ AES-CCM-64-64-128 \ \ kid \ 4: h'1234' } / , / unprotected / { / iv / 5:h'89f52f65a1c580', / countersign / 7:[ / protected / h'a10126' / { \ alg \ 1:-7 } / , / unprotected / { / kid / 4:h'11' }, / signature / SIG / 64 bytes signature / ] }, / ciphertext / h'8df0a3b62fccff37aa313c8020e971f8aC8d' ] ) Figure 12: Example of COSE Object sent in the payload of a PUBLISH operation The encryption and decryption operations are described in sections 5.3 and 5.4 of [RFC8152]. 6. Profile-specific Considerations This section summarises the CoAP and MQTT specific pub-sub communications, and considerations respectively. 6.1. CoAP PubSub Application Profile A CoAP Pub-Sub Client and Broker use an ACE transport profile such as DTLS [I-D.ietf-ace-dtls-authorize], OSCORE [I-D.ietf-ace-oscore-profile]. As shown in Figure 1, (A) is an Access Token Request and Response exchange between Publisher and Authorization Server to retrieve the Access Token and RS (Broker) Information. As specified, the Client has the role of a CoAP client, the Broker has the role of the CoAP server. Palombini & Sengul Expires 1 January 2022 [Page 13] Internet-Draft pubsub-profile June 2021 (B) corresponds to the retrieval of the keying material to protect the publication end-to-end (see Section 5.1), and uses [I-D.ietf-ace-key-groupcomm]. The details are defined in Section 4. (C) corresponds to the exchange between the Client and the Broker, where the Client sends its access token to the Broker and establishes a secure connection with the Broker. Depending on the Information received in (A), this can be for example DTLS handshake, or other protocols. Depending on the application, there may not be the need for this set up phase: for example, if OSCORE is used directly. Note that, in line with what defined in the ACE transport profile used, the access token includes the scope (i.e. pubsub topics on the Broker) the Publisher is allowed to publish to. For implementation simplicity, it is RECOMMENDED that the ACE transport profile used and this specification use the same format of "scope". After the previous phases have taken place, the pub-sub communication can commence. The operations of publishing and subscribing are defined in [I-D.ietf-core-coap-pubsub]. 6.2. MQTT PubSub Application Profile The steps MQTT clients go through are similar to the CoAP clients as described in Section 6.1. The payload that is carried in MQTT messages will be protected using COSE. In MQTT, topics are organised as a tree, and in the [I-D.ietf-ace-mqtt-tls-profile] 'scope' captures permissions for not a single topic but a topic filter. Therefore, topic names (i.e., group names) may include wildcards spanning several levels of the topic tree. Hence, it is important to distinguish application groups and security groups defined in [I-D.ietf-core-groupcomm-bis]. An application group has relevance at the application level - for example, in MQTT an application group could denote all topics stored under ""home/lights/". On the other hand, a security group is a group of endpoints that each store group security material to exchange secure communication within the group. The group communication in [I-D.ietf-ace-key-groupcomm] refers to security groups. To be able join the right security group associated with requested topics (application groups), the client needs to discover the (application group, security group) association. In MQTT, $SYS/ has been widely adopted as a prefix to topics that contain broker- specific information, and hence, can be used by the broker for this purpose. In typical implementations, Clients that subscribe to one or more SYS-Topics receive the current value on the SYS topics as soon as they subscribe, and then after periodically. Palombini & Sengul Expires 1 January 2022 [Page 14] Internet-Draft pubsub-profile June 2021 For an MQTT client we envision the following steps to take place: 1. Client learns the (application group, security group) associations from the $SYS topic (this topic is RECOMMENDED to be a protected topic). These associations MAY be published under another topic. 2. Client computes the corresponding security groups for its application groups, and sends token requests for the security groups to AS. 3. Client sends join requests to KDC to gets the keys for these security groups. 4. Client authorises to the Broker with the token (described in [I-D.ietf-ace-mqtt-tls-profile]). 5. A Publisher Client sends PUBLISH messages for a given topic and protects the payload with the corresponding key for the associated security group. RS validates the PUBLISH message by checking the topic's security group association and the stored token. 6. A Subscriber Client may send SUBSCRIBE messages with one or multiple topic filters. A topic filter may correspond to multiple topics but MUST belong to a single security group. If requested topics are in multiple security groups, then these topics SHOULD be separated into the corresponding topic filters in the SUBSCRIBE message. 7. Security Considerations In the profile described above, the Publisher and Subscriber use asymmetric crypto, which would make the message exchange quite heavy for small constrained devices. Moreover, all Subscribers must be able to access the public keys of all the Publishers to a specific topic to be able to verify the publications. Such a database could be set up and managed by the same entity having control of the topic, i.e. KDC. Palombini & Sengul Expires 1 January 2022 [Page 15] Internet-Draft pubsub-profile June 2021 An application where it is not critical that only authorized Publishers can publish on a topic may decide not to make use of the asymmetric crypto and only use symmetric encryption/MAC to confidentiality and integrity protection of the publication. However, this is not recommended since, as a result, any authorized Subscribers with access to the Broker may forge unauthorized publications without being detected. In this symmetric case the Subscribers would only need one symmetric key per topic, and would not need to know any information about the Publishers, that can be anonymous to it and the Broker. Subscribers can be excluded from future publications through re- keying for a certain topic. This could be set up to happen on a regular basis, for certain applications. How this could be done is out of scope for this work. The Broker is only trusted with verifying that the Publisher is authorized to publish, but is not trusted with the publications itself, which it cannot read nor modify. In this setting, caching of publications on the Broker is still allowed. TODO: expand on security and privacy considerations 8. IANA Considerations 8.1. ACE Groupcomm Profile Registry The following registrations are done for the "ACE Groupcomm Profile" Registry following the procedure specified in [I-D.ietf-ace-key-groupcomm]. Note to RFC Editor: Please replace all occurrences of "[[This document]]" with the RFC number of this specification and delete this paragraph. 8.1.1. CoAP Profile Registration Name: coap_pubsub_app Description: Profile for delegating client authentication and authorization for publishers and subscribers in a CoAP pub-sub setting scenario in a constrained environment. CBOR Key: TBD Reference: [[This document]] Palombini & Sengul Expires 1 January 2022 [Page 16] Internet-Draft pubsub-profile June 2021 8.1.2. MQTT Profile Registration Name: mqtt_pubsub_app Description: Profile for delegating client authentication and authorization for publishers and subscribers in a MQTT pub-sub setting scenario in a constrained environment. CBOR Key: TBD Reference: [[This document]] 8.2. ACE Groupcomm Key Registry The following registrations are done for the ACE Groupcomm Key Registry following the procedure specified in [I-D.ietf-ace-key-groupcomm]. Note to RFC Editor: Please replace all occurrences of "[[This document]]" with the RFC number of this specification and delete this paragraph. Name: COSE_Key Key Type Value: TBD Profile: coap_pubsub_app Description: COSE_Key object References: [RFC8152], [[This document]] 9. References 9.1. Normative References [I-D.ietf-ace-key-groupcomm] Palombini, F. and M. Tiloca, "Key Provisioning for Group Communication using ACE", Work in Progress, Internet- Draft, draft-ietf-ace-key-groupcomm-11, 22 February 2021, . [I-D.ietf-ace-oauth-authz] Seitz, L., Selander, G., Wahlstroem, E., Erdtman, S., and H. Tschofenig, "Authentication and Authorization for Constrained Environments (ACE) using the OAuth 2.0 Framework (ACE-OAuth)", Work in Progress, Internet-Draft, Palombini & Sengul Expires 1 January 2022 [Page 17] Internet-Draft pubsub-profile June 2021 draft-ietf-ace-oauth-authz-40, 26 April 2021, . [I-D.ietf-core-coap-pubsub] Koster, M., Keranen, A., and J. Jimenez, "Publish- Subscribe Broker for the Constrained Application Protocol (CoAP)", Work in Progress, Internet-Draft, draft-ietf- core-coap-pubsub-09, 30 September 2019, . [I-D.ietf-core-groupcomm-bis] Dijk, E., Wang, C., and M. Tiloca, "Group Communication for the Constrained Application Protocol (CoAP)", Work in Progress, Internet-Draft, draft-ietf-core-groupcomm-bis- 03, 22 February 2021, . [MQTT-OASIS-Standard-v5] Banks, A., Briggs, E., Borgendale, K., and R. Gupta, "OASIS Standard MQTT Version 5.0", 2017, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC6749] Hardt, D., Ed., "The OAuth 2.0 Authorization Framework", RFC 6749, DOI 10.17487/RFC6749, October 2012, . [RFC8152] Schaad, J., "CBOR Object Signing and Encryption (COSE)", RFC 8152, DOI 10.17487/RFC8152, July 2017, . [RFC8949] Bormann, C. and P. Hoffman, "Concise Binary Object Representation (CBOR)", STD 94, RFC 8949, DOI 10.17487/RFC8949, December 2020, . 9.2. Informative References [I-D.ietf-ace-actors] Gerdes, S., Seitz, L., Selander, G., and C. Bormann, "An architecture for authorization in constrained Palombini & Sengul Expires 1 January 2022 [Page 18] Internet-Draft pubsub-profile June 2021 environments", Work in Progress, Internet-Draft, draft- ietf-ace-actors-07, 22 October 2018, . [I-D.ietf-ace-dtls-authorize] Gerdes, S., Bergmann, O., Bormann, C., Selander, G., and L. Seitz, "Datagram Transport Layer Security (DTLS) Profile for Authentication and Authorization for Constrained Environments (ACE)", Work in Progress, Internet-Draft, draft-ietf-ace-dtls-authorize-16, 8 March 2021, . [I-D.ietf-ace-mqtt-tls-profile] Sengul, C. and A. Kirby, "Message Queuing Telemetry Transport (MQTT)-TLS profile of Authentication and Authorization for Constrained Environments (ACE) Framework", Work in Progress, Internet-Draft, draft-ietf- ace-mqtt-tls-profile-11, 14 April 2021, . [I-D.ietf-ace-oscore-profile] Palombini, F., Seitz, L., Selander, G., and M. Gunnarsson, "OSCORE Profile of the Authentication and Authorization for Constrained Environments Framework", Work in Progress, Internet-Draft, draft-ietf-ace-oscore-profile-18, 14 April 2021, . [RFC8259] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data Interchange Format", STD 90, RFC 8259, DOI 10.17487/RFC8259, December 2017, . Appendix A. Requirements on Application Profiles This section lists the specifications on this profile based on the requirements defined in Appendix A of [I-D.ietf-ace-key-groupcomm] * REQ1: Specify the encoding and value of the identifier of group or topic of 'scope': see Section 4). * REQ2: Specify the encoding and value of roles of 'scope': see Section 4). Palombini & Sengul Expires 1 January 2022 [Page 19] Internet-Draft pubsub-profile June 2021 * REQ3: Optionally, specify the acceptable values for 'sign_alg': TODO * REQ4: Optionally, specify the acceptable values for 'sign_parameters': TODO * REQ5: Optionally, specify the acceptable values for 'sign_key_parameters': TODO * REQ6: Optionally, specify the acceptable values for 'pub_key_enc': TODO * REQ7: Specify the exact format of the 'key' value: COSE_Key, see Section 4. * REQ8: Specify the acceptable values of 'kty' : "COSE_Key", see Section 4. * REQ9: Specity the format of the identifiers of group members: TODO * REQ10: Optionally, specify the format and content of 'group_policies' entries: not defined * REQ11: Specify the communication protocol the members of the group must use: CoAP pub/sub. * REQ12: Specify the security protocol the group members must use to protect their communication. This must provide encryption, integrity and replay protection: Object Security of Content using COSE, see Section 5.1. * REQ13: Specify and register the application profile identifier : "coap_pubsub_app", see Section 8.1. * REQ14: Optionally, specify the encoding of public keys, of 'client_cred', and of 'pub_keys' if COSE_Keys are not used: NA. * REQ15: Specify policies at the KDC to handle id that are not included in get_pub_keys: TODO * REQ16: Specify the format and content of 'group_policies': TODO * REQ17: Specify the format of newly-generated individual keying material for group members, or of the information to derive it, and corresponding CBOR label : not defined Palombini & Sengul Expires 1 January 2022 [Page 20] Internet-Draft pubsub-profile June 2021 * REQ18: Specify how the communication is secured between Client and KDC. Optionally, specify tranport profile of ACE [I-D.ietf-ace-oauth-authz] to use between Client and KDC: pre-set, as KDC is AS. * OPT1: Optionally, specify the encoding of public keys, of 'client_cred', and of 'pub_keys' if COSE_Keys are not used: NA * OPT2: Optionally, specify the negotiation of parameter values for signature algorithm and signature keys, if 'sign_info' and 'pub_key_enc' are not used: NA * OPT3: Optionally, specify the format and content of 'mgt_key_material': not defined * OPT4: Optionally, specify policies that instruct clients to retain unsuccessfully decrypted messages and for how long, so that they can be decrypted after getting updated keying material: not defined Acknowledgments The author wishes to thank Ari Keraenen, John Mattsson, Ludwig Seitz, Goeran Selander, Jim Schaad and Marco Tiloca for the useful discussion and reviews that helped shape this document. Authors' Addresses Francesca Palombini Ericsson Email: francesca.palombini@ericsson.com Cigdem Sengul Brunel University Email: csengul@acm.org Palombini & Sengul Expires 1 January 2022 [Page 21]