AAA Working Group Pat R. Calhoun Internet-Draft Black Storm Networks Category: Standards Track Jari Arkko Ericsson Erik Guttman Sun Microsystems, Inc. Glen Zorn Cisco Systems, Inc. John Loughney Nokia June 2002 Diameter Base Protocol Status of this Memo This document is an Internet-Draft and is subject to all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Distribution of this memo is unlimited. Copyright (C) The Internet Society 2002. All Rights Reserved. Calhoun et al. expires November 2002 [Page 1] Internet-Draft June 2002 Abstract The Diameter base protocol is intended to provide an AAA framework for applications such as network access or IP mobility. Diameter is also intended to work both with local AAA and with roaming situations. This draft specifies the message format, transport, error reporting, accounting and security services to be used by all Diameter applications and MUST be supported by all Diameter implementations. Table of Contents 1 Introduction 1.1 Diameter Protocol 1.1.1 Differences from RADIUS 1.1.2 Description of the Document Set 1.2 Approach to Extensibility 1.2.1 Defining New AVP Values 1.2.2 Creating New AVPs 1.2.3 Creating New Authentication Applications 1.2.4 Creating New Accounting Applications 1.2.5 Application Authentication Procedures 1.3 Requirements Language 1.4 Terminology 2 Protocol Overview 2.1 Transport 2.1.1 SCTP Guidelines 2.2 Securing Diameter Messages 2.3 Diameter Application Compliance 2.4 Application Identifiers 2.5 Connections vs. Sessions 2.6 Peer Table 2.7 Realm-Based Routing Table 2.8 Role of Diameter Agents 2.8.1 Relay Agents 2.8.2 Proxy Agents 2.8.3 Redirect Agents 2.8.4 Translation Agents 2.9 End-to-End Security Framework 3 Diameter Header 3.1 Command Codes 3.2 Command Code ABNF specification 3.3 Diameter Command Naming Conventions 4 Diameter AVPs 4.1 AVP Header Calhoun et al. expires November 2002 [Page 2] Internet-Draft June 2002 4.2 Optional Header Elements 4.3 Basic AVP Data Formats 4.4 Derived AVP Data Formats 4.5 Grouped AVP Values 4.5.1 Example AVP with a Grouped Data Type 4.6 Diameter Base Protocol AVPs 5 Diameter Peers 5.1 Peer Connections 5.2 Diameter Peer Discovery 5.3 Capabilities Exchange 5.3.1 Capabilities-Exchange-Request 5.3.2 Capabilities-Exchange-Answer 5.3.3 Vendor-Id AVP 5.3.4 Firmware-Revision AVP 5.3.5 Host-IP-Address AVP 5.3.6 Supported-Vendor-Id AVP 5.3.7 Product-Name AVP 5.4 Disconnecting Peer Connections 5.4.1 Disconnect-Peer-Request 5.4.2 Disconnect-Peer-Answer 5.4.3 Disconnect-Cause AVP 5.5 Transport Failure Detection 5.5.1 Device-Watchdog-Request 5.5.2 Device-Watchdog-Answer 5.5.3 Transport Failure Algorithm 5.5.4 Failover and Failback Procedures 5.6 Peer State Machine 5.6.1 Incoming connections 5.6.2 Events 5.6.3 Actions 5.6.4 The Election Process 6 Diameter Message Processing 6.1 Diameter Request Routing Overview 6.1.1 Originating a Request 6.1.2 Sending a Request 6.1.3 Receiving Requests 6.1.4 Processing Local Requests 6.1.5 Request Forwarding 6.1.6 Request Routing 6.1.7 Redirecting Requests 6.1.8 Relaying and Proxying Requests 6.2 Diameter Answer Processing 6.2.1 Processing Received Answers 6.2.2 Relaying and Proxying Answers 6.3 Origin-Host AVP 6.4 Origin-Realm AVP Calhoun et al. expires November 2002 [Page 3] Internet-Draft June 2002 6.5 Destination-Host AVP 6.6 Destination-Realm AVP 6.7 Routing AVPs 6.7.1 Route-Record AVP 6.7.2 Proxy-Info AVP 6.7.3 Proxy-Host AVP 6.7.4 Proxy-State AVP 6.8 Auth-Application-Id AVP 6.9 Acct-Application-Id AVP 6.10 Inband-Security-Id AVP 6.11 Vendor-Specific-Application-Id AVP 6.12 Redirect-Host AVP 6.13 Redirect-Host-Usage AVP 6.14 Redirect-Max-Cache-Time AVP 6.15 E2E-Sequence AVP 7 Error Handling 7.1 Result-Code AVP 7.1.1 Informational 7.1.2 Success 7.1.3 Protocol Errors 7.1.4 Transient Failures 7.1.5 Permanent Failures 7.2 Error Bit 7.3 Error-Message AVP 7.4 Error-Reporting-Host AVP 7.5 Failed-AVP AVP 7.6 Vendor-Specific-Result AVP 7.7 Vendor-Specific-Result-Code AVP 8 Diameter User Sessions 8.1 Authorization Session State Machine 8.2 Accounting Session State Machine 8.3 Server-Initiated Re-Auth 8.3.1 Re-Auth-Request 8.3.2 Re-Auth-Answer 8.4 Session Termination 8.4.1 Session-Termination-Request 8.4.2 Session-Termination-Answer 8.5 Aborting a Session 8.5.1 Abort-Session-Request 8.5.2 Abort-Session-Answer 8.6 Inferring Session Termination from Origin-State-Id 8.7 Auth-Request-Type AVP 8.8 Session-Id AVP 8.9 Authorization-Lifetime AVP 8.10 Auth-Grace-Period AVP 8.11 Auth-Session-State AVP Calhoun et al. expires November 2002 [Page 4] Internet-Draft June 2002 8.12 Re-Auth-Request-Type AVP 8.13 Session-Timeout AVP 8.14 User-Name AVP 8.15 Termination-Cause AVP 8.16 Origin-State-Id AVP 8.17 Session-Binding AVP 8.18 Session-Server-Failover AVP 8.19 Multi-Round-Time-Out AVP 8.20 Class AVP 8.21 Event-Timestamp AVP 9 Accounting 9.1 Server Directed Model 9.2 Protocol Messages 9.3 Application Document Requirements 9.4 Fault Resilience 9.5 Accounting Records 9.6 Correlation of Accounting Records 9.7 Accounting Command-Codes 9.7.1 Accounting-Request 9.7.2 Accounting-Answer 9.8 Accounting AVPs 9.8.1 Accounting-Record-Type AVP 9.8.2 Acct-Interim-Interval AVP 9.8.3 Accounting-Record-Number AVP 9.8.4 Accounting-RADIUS-Session-Id AVP 9.8.5 Acct-Multi-Session-Id AVP 9.8.6 Accounting-Sub-Session-Id AVP 9.8.7 Accounting-Realtime-Required AVP 10 AVP Occurrence Table 10.1 Base Protocol Command AVP Table 10.2 Accounting AVP Table 11 IANA Considerations 11.1 AVP Header 11.1.1 AVP Code 11.1.2 AVP Flags 11.2 Diameter Header 11.2.1 Command Codes 11.2.2 Command Flags 11.3 Application Identifiers 11.4 Result-Code AVP Values 11.5 Accounting-Record-Type AVP Values 11.6 Termination-Cause AVP Values 11.7 Redirect-Host-Usage AVP Values 11.8 Session-Server-Failover AVP Values 11.9 Session-Binding AVP Values Calhoun et al. expires November 2002 [Page 5] Internet-Draft June 2002 11.10 Diameter TCP/SCTP Port Numbers 11.11 Disconnect-Cause AVP Values 11.12 Auth-Request-Type AVP Values 11.13 Auth-Session-State AVP Values 11.14 Re-Auth-Request-Type AVP Values 11.15 NAPTR Service Fields 11.16 Accounting-Realtime-Required AVP Values 12 Diameter Protocol Related Configurable Parameters 13 Security Considerations 13.1 IPsec Usage 13.2 TLS Usage 13.3 Peer-to-Peer Considerations 14 References 14.1 Normative 14.2 Non-Normative 15 Acknowledgements 16 Authors' Addresses 17 Full Copyright Statement 18 Expiration Date Appendix A. Diameter Service Template Appendix B. NAPTR Example Appendix C. Duplicate Detection Calhoun et al. expires November 2002 [Page 6] Internet-Draft June 2002 1 Introduction Historically, the RADIUS protocol has been used to provide AAA services for dial-up PPP [PPP] and terminal server access. Over time, routers and network access servers (NAS) have increased in complexity and density, making the RADIUS protocol increasingly unsuitable for use in such networks. Some of the major issues of using RADIUS include: - RADIUS does not define a backoff procedure. - RADIUS leaves failover mechanisms unspecified. - Application layer acknowledgement is missing. - The behaviour of proxies isn't clearly defined. - The lack of error messages prevent intelligent failure responses. - Transport security applied in RADIUS has no confidentiality, and there are known attacks against it. - Replay protection can only be done in post-processing. - RADIUS does not protect data objects passed through it, and it is open to man-in-the-middle attacks The effort to fix RADIUS would be substantial, and the result would be a protocol very close to Diameter. In fact, quite a bit of effort has been made to insure that Diameter will interoperate with RADIUS. The Roaming Operations Working Group (ROAMOPS) has published a set of specifications [ROAMCRIT, ROAMREV, PROXYCHAIN] that define how a PPP user can gain access to the Internet without having to dial into his/her home service provider's modem pool. This is achieved by allowing service providers to cross-authenticate their users. Effectively, a user can dial into any service provider's point of presence (POP) that has a roaming agreement with his/her home Internet service provider (ISP), the benefit being that the user does not have to incur a long distance charge while traveling, which can sometimes be quite expensive. Given the number of ISPs today, ROAMOPS realized that requiring each ISP to set up roaming agreements with all other ISPs did not scale. Therefore, the working group defined a "broker", which acts as an intermediate server, whose sole purpose is to set up these roaming agreements. A collection of ISPs and a broker is called a "roaming consortium". There are many such brokers in existence today; many also provide settlement services for member ISPs. The Mobile-IP Working Group has recently changed its focus to inter- administrative domain mobility, which is a requirement for cellular carriers wishing to deploy IETF-based mobility protocols. The current cellular carriers requirements [CDMA2000REQ, MIPREQ] are very similar Calhoun et al. expires November 2002 [Page 7] Internet-Draft June 2002 to the ROAMOPS model, with the exception that the access protocol is Mobile-IP [MIPV4] instead of PPP. The Network Access Server Requirements (NASREQ) working group has focused on proving next generation Authentication, Authorization and usage Accounting for simple dial-in access and beyond; such as Virtual Private Network support, smart authentication methods, and roaming concerns. The Working Group has published number of documents including the requirements for NAS service protocols [NASNG] as well as criteria for evaluating NAS protocols [NASCRIT]. The basic concept behind Diameter is to provide a base protocol that can be extended in order to provide AAA services to new access technologies. Currently, the protocol only concerns itself with Internet access, both in the traditional PPP sense as well as taking into account the ROAMOPS model, and Mobile-IP. Although Diameter could be used to solve a wider set of AAA problems, we are currently limiting the scope of the protocol in order to ensure that the effort remains focused on satisfying the requirements of network access. Note that a truly generic AAA protocol used by many applications might provide functionality not provided by Diameter. Therefore, it is imperative that the designers of new applications understand their requirements before using Diameter. 1.1 Diameter Protocol The Diameter protocol allows peers to exchange a variety of messages. The base protocol provides the following facilities: - Delivery of AVPs (attribute value pairs) - Capabilities negotiation, as required in [ROAMCRIT] - Error notification - Extensibility, through addition of new commands and AVPs, as required in [NASCRIT] - Basic services necessary for applications, such as handling of user sessions or accounting All data delivered by the protocol is in the form of an AVP. Some of these AVP values are used by the Diameter protocol itself, while others deliver data associated with particular applications that employ Diameter. AVPs may be added arbitrarily to Diameter messages, so long as the required AVPs are included and AVPs that are explicitly excluded are not included. AVPs are used by the base Diameter protocol to support the following required features: - Transporting of user authentication information, for the Calhoun et al. expires November 2002 [Page 8] Internet-Draft June 2002 purposes of enabling the Diameter server to authenticate the user. - Transporting of service specific authorization information, between client and servers, allowing the peers to decide whether a user's access request should be granted. - Exchanging resource usage information, which MAY be used for accounting purposes, capacity planning, etc. - Relaying, proxying and redirecting of Diameter messages through a server hierarchy. The Diameter base protocol provides the minimum requirements needed for an AAA transport protocol, as required by NASREQ [NASCRIT], Mobile IP [CDMA2000REQ, MIPREQ], and ROAMOPS [ROAMCRIT]. The base protocol is not intended to be used by itself, and must be used with a Diameter application, such as Mobile IP [DIAMMIP]. The Diameter protocol was heavily inspired by and builds upon the tradition of the RADIUS [RADIUS] protocol. See section 2.4 for more information on Diameter applications. Any node can initiate a request. In that sense, Diameter is a peer- to-peer protocol. In this document, a Diameter Client is a device at the edge of the network that performs access control, such as aNetwork Access Server (NAS) or a Foreign Agent (FA). A Diameter client generates Diameter messages to request authentication, authorization, and accounting services for the user. A Diameter agent is a node that does not authenticate and/or authorize messages locally. Examples of agents are proxies and relay agents. A Diameter server is one that performs authentication and/or authorization of the user based on some profile. A Diameter node MAY act as an agent for certain requests while acting as a server for others. The Diameter protocol also supports server-initiated messages towards access devices, such as a request to abort service to a particular user. 1.1.1 Differences from RADIUS The Diameter protocol was not designed from the ground up. Instead, the basic RADIUS model was retained while fixing the flaws in the RADIUS protocol itself. Diameter does not share a common protocol data unit (PDU) with RADIUS, but does borrow sufficiently from the protocol to ease migration. The major differences include: - Peer-to-peer nature - Explicit support for intermediaries - Connection-oriented versus connectionless transport - Extensibility [see section 1.2] - Built-in failover support Calhoun et al. expires November 2002 [Page 9] Internet-Draft June 2002 - Larger attribute space - Integrated accounting - Bit to indicate mandatory status of data - Application-layer ACKs and error messages - Unsolicited server messages - Peer discovery - Capabilities negotiation - Stronger peer-to-peer security - Optional end-to-end payload security - Transport layer retransmission 1.1.2 Description of the Document Set Currently, the Diameter specification consists of a base specification (this document), Transport Issues [AAATRANS] and a number of applications: Mobile IPv4 [DIAMMIP], NASREQ [NASREQ]. The Transport Issues document [AAATRANS] discusses transport layer issues that arise with AAA protocols and recommendations on how to overcome these issues. The Mobile IPv4 [DIAMMIP] application defines a Diameter application that allows a Diameter server to perform AAA functions for Mobile IPv4 services to a mobile node. The NASREQ [NASREQ] application defines a Diameter Application that allows a Diameter server to be used in a PPP/SLIP Dial-Up and Terminal Server Access environment. Consideration was given for servers that need to perform protocol conversion between Diameter and RADIUS. In summary, this document defines the base protocol specification for AAA. The MIPv4 and the NASREQ documents describe applications that use this base specification to achieve Authentication, Authorization and Accounting. 1.2 Approach to Extensibility The Diameter protocol is designed to be extensible. However, it is strongly encouraged to reuse existing mechanisms before attempting any Diameter extensions. The extensibility includes: - Defining new AVP values. - Creating new AVPs - Creating new authentication/autorization applications - Creating new accounting applications - Application authentication procedures Calhoun et al. expires November 2002 [Page 10] Internet-Draft June 2002 1.2.1 Defining New AVP Values New applications should attempt to reuse AVPs defined in existing applications when possible, as opposed to creating new AVPs. For AVPs of type Enumerated, it is possible the application requires a new value to communicate some service-specific information. In order to allocate a new AVP value, a request MUST be sent to IANA [47], with a detailed explanation of the value. 1.2.2 Creating New AVPs When no existing AVP can be used appropriately to communicate some service-specific information, a new AVP should be created. The new AVP being defined MUST follow one of the types listed in section 4.3. In the event that a logical grouping of AVPs is necessary, and multiple "groups" are possible in a given command, it is highly recommended that a Grouped AVP be used (see Section 4.5). In order to create a new AVP, a request MUST be sent to IANA, with a detailed explanation of the AVP, its type and possible values. Furthermore, the request MUST include the commands that would make use of the AVP. 1.2.3 Creating New Authentication Applications Should a new application require Diameter support, but it cannot fit within an existing application without requiring major changes to the specification, it may be desirable to create a new Diameter application. Major changes to an application include: - Requiring a whole different set of mandatory AVPs to a command - Requiring a command that has a different number of round trips to satisfy a request (e.g. application foo has a command that requires one round trip, but new application bar has a command that requires two round trips to complete). - The method used to authenticate the user is drastically different from any existing application, and the authentication information cannot be carried within the AVPs defined in the application. Note that the creation of a new application should be viewed as a last resort. New Diameter applications MUST define at least one Command Code, the expected AVPs in an ABNF [ABNF] grammar (see section 3.2), and MAY also define new AVPs. If the Diameter application has any accounting requirements, it MUST also specify the AVPs that are to be present in Calhoun et al. expires November 2002 [Page 11] Internet-Draft June 2002 the Diameter Accounting messages (see section 9.3). When possible, a new Diameter application SHOULD attempt to re-use any existing Diameter AVP, in order to reduce the possibility of having multiple AVPs that carry similar information. Every Diameter application specification MUST have an IANA assigned Application Identifier (see section 2.4). 1.2.4 Creating New Accounting Applications Services that have an Application Identifier MUST use the same identifier also to identify the service when Diameter accounting is used. There are services that only require the use of Diameter accounting. Such services need to define the service specific AVPs that must be carried in the Accounting-Request/Answer messages, but do not need to define command codes. Application Identifiers are, however, still required for accounting due to the Diameter capability discovery process. Every accounting application MUST have either an IANA allocated Application Identifier, or a vendor specific Application Identifier. Note that the creation of a new application should be viewed as a last resort and should be used only when Vendor-Specific AVPs are insufficient. In most cases, reusing an existing Application ID with Vendor-Specific AVPs should work. For example, many accounting servers are set up to write AVPs to disk, so they can handle even mandatory vendor-specific AVPs that they don't understand. This is why "disk writing" accounting servers should advertise themselves as "Relays" that can handle any Application ID, including Vendor-Specific. When possible, a new Diameter accounting application SHOULD attempt to re-use any existing Diameter AVP, in order to reduce the possibility of having multiple AVPs that carry similar information. Every Diameter accounting application specification MUST have an IANA assigned Application Identifier (see section 2.4). 1.2.5 Application Authentication Procedures When possible, applications SHOULD be designed such that new authentication methods MAY be added without requiring changes to the application. This MAY require that new AVP values be assigned to represent the new authentication transform, or any other scheme that Calhoun et al. expires November 2002 [Page 12] Internet-Draft June 2002 produces similar results. When possible, authentication frameworks, such as Extensible Authentication Protocol [EAP], SHOULD be used. 1.3 Requirements Language In this document, the key words "MAY", "MUST", "MUST NOT", "OPTIONAL", "RECOMMENDED", "SHOULD", and "SHOULD NOT", are to be interpreted as described in [KEYWORDS]. 1.4 Terminology AAA Authentication, Authorization and Accounting. Accounting The act of collecting information on resource usage for the purpose of capacity planning, auditing, billing or cost allocation. Accounting Record A session record represents a summary of the resource consumption of a user over the entire session. Accounting servers creating the session record may do so by processing interim accounting events or accounting events from several devices serving the same user. Authentication The act of verifying the identity of an entity (subject). Authorization The act of determining whether a requesting entity (subject) will be allowed access to a resource (object). AVP The Diameter protocol consists of a header followed by one or more Attribute-Value-Pairs (AVPs). An AVP includes a header and is used to encapsulate protocol-specific data (e.g. routing information) as well as authentication, authorization or accounting information. Broker A broker is a business term commonly used in AAA infrastructures. A broker is either a relay, proxy or redirect agent, and MAY be operated by roaming consortiums. Depending on the business model, a broker may either choose to deploy relay agents or proxy agents. Calhoun et al. expires November 2002 [Page 13] Internet-Draft June 2002 Diameter Agent A Diameter Agent is a Diameter node that provides either relay, proxy, redirect or translation services. Diameter Client A Diameter Client is a device at the edge of the network that performs access control. An example of a Diameter client is a Network Access Server (NAS) or a Foreign Agent (FA). Diameter Node A Diameter node is a host process that implements the Diameter protocol, and acts either as a Client, Agent or Server. Diameter Peer A Diameter Peer is a Diameter Node to which a given Diameter Node has a direct transport connection. Diameter Security Exchange A Diameter Security Exchange is a process through which two Diameter nodes establish end-to-end security. Diameter Server A Diameter Server is one that handles authentication, authorization and accounting requests for a particular realm. By its very nature, a Diameter Server MUST support Diameter applications in addition to the base protocol. Downstream Downstream is used to identify the direction of a particular Diameter message from the home server towards the access device. End-to-End Security TLS and IPsec provide hop-by-hop security, or security across a transport connection. When relays or proxy are involved, this hop-by-hop security does not protect the entire Diameter user session. End-to-end security is security across a Diameter session. Home Realm A Home Realm is the administrative domain with which the user maintains an account relationship. Home Server See Diameter Server. Interim accounting An interim accounting message provides a snapshot of usage during a user's session. It is typically implemented in order to provide Calhoun et al. expires November 2002 [Page 14] Internet-Draft June 2002 for partial accounting of a user's session in the case of a device reboot or other network problem prevents the reception of a session summary message or session record. Local Realm A local realm is the administrative domain providing services to a user. An administrative domain MAY act as a local realm for certain users, while being a home realm for others. Multi-session A multi-session represents a logical linking of several sessions. Multi-sessions are tracked by using the Acct-Multi-Session-Id. An example of a multi-session would be a Multi-link PPP bundle. Each leg of the bundle would be a session while the entire bundle would be a multi-session. Network Access Identifier The Network Access Identifier, or NAI [NAI], is used in the Diameter protocol to extract a user's identity and realm. The identity is used to identify the user during authentication and/or authorization, while the realm is used for message routing purposes. Proxy Agent or Proxy In addition to forwarding requests and responses, proxies make policy decisions relating to resource usage and provisioning. This is typically accomplished by tracking the state of NAS devices. While proxies typically do not respond to client Requests prior to receiving a Response from the server, they may originate Reject messages in cases where policies are violated. As a result, proxies need to understand the semantics of the messages passing through them, and may not support all Diameter applications. Realm The string in the NAI that immediately follows the '@' character. NAI realm names are required to be unique, and are piggybacked on the administration of the DNS namespace. Diameter makes use of the realm, also loosely referred to as domain, to determine whether messages can be satisfied locally, or whether they must be routed or redirected. In RADIUS, realm names are not necessarily piggybacked on the DNS namespace but may be independent of it. Real-time Accounting Real-time accounting involves the processing of information on resource usage within a defined time window. Time constraints are typically imposed in order to limit financial risk. Relay Agent or Relay Calhoun et al. expires November 2002 [Page 15] Internet-Draft June 2002 Relays forward requests and responses based on routing-related AVPs and realm routing table entries. Since relays do not make policy decisions, they do not examine or alter non-routing AVPs. As a result, relays never originate messages, do not need to understand the semantics of messages or non-routing AVPs, and are capable of handling any Diameter application or message type. Since relays make decisions based on information in routing AVPs and realm forwarding tables they do not keep state on NAS resource usage or sessions in progress. Redirect Agent Rather than forwarding requests and responses between clients and servers, redirect agents refer clients to servers and allow them to communicate directly. Since redirect agents do not sit in the forwarding path, they do not alter any AVPs transiting between client and server. Redirect agents do not originate messages and are capable of handling any message type, although they may be configured only to redirect messages of certain types, while acting as relay or proxy agents for other types. As with proxy agents, redirect agents do not keep state with respect to sessions or NAS resources. Roaming Relationships Roaming relationships include relationships between companies and ISPs, relationships among peer ISPs within a roaming consortium, and relationships between an ISP and a roaming consortium. Security Association A security association is an association between two endpoints in a Diameter session which allows the endpoints to communicate with integrity and confidentially, even in the presense of relays and/or proxies. Session A session is a related progression of events devoted to a particular activity. Each application SHOULD provide guidelines as to when a session begins and ends. All Diameter packets with the same Session-Identifier are considered to be part of the same session. Sub-session A sub-session represents a distinct service (e.g. QoS or data characteristics) provided to a given session. These services may happen concurrently (e.g. simultaneous voice and data transfer during the same session) or serially. These changes in sessions are tracked with the Accounting-Sub-Session-Id. Translation Agent Calhoun et al. expires November 2002 [Page 16] Internet-Draft June 2002 A translation agent is a stateful Diameter node that performs protocol translation between Diameter and another AAA protocol, such as RADIUS. Tranport Connection A transport connection is a TCP or SCTP connection existing directy between two Diameter peers, otherwise known as a Peer-to- Peer Connection. Upstream Upstream is used to identify the direction of a particular Diameter message from the access device towards the home server. 2 Protocol Overview The base Diameter protocol is never used on its own. It is always extended for a particular application. Three Diameter applications are defined by companion documents: NASREQ [NASREQ], Mobile IP [DIAMMIP]. These applications are introduced in this document but specified elsewhere. Additional Diameter applications MAY be defined in the future (see Section 11.3). Diameter Clients MUST support the base protocol, which includes accounting. In addition, they MUST fully support each Diameter application that is needed to implement the client's service, e.g. NASREQ and/or Mobile IP. A Diameter Client that does not support both NASREQ and Mobile IP, MUST be referred to as "Diameter X Client" where X is the application which it supports, and not a "Diameter Client." Diameter Servers MUST support the base protocol, which includes accounting. In addition, they MUST fully support each Diameter application that is needed to implement the intended service, e.g. NASREQ and/or Mobile IP. A Diameter Server that does not support both NASREQ and Mobile IP, MUST be referred to as "Diameter X Server" where X is the application which it supports, and not a "Diameter Server." Diameter Relays and Redirect agents are, by definition, protocol transparent, and MUST transparently support the Diameter base protocol, which includes accounting, and all Diameter applications. Diameter Proxies MUST support the base protocol, which includes accounting. In addition, they MUST fully support each Diameter application that is needed to implement proxied services, e.g. NASREQ and/or Mobile IP. A Diameter Proxy which does not support also both NASREQ and Mobile IP, MUST be referred to as "Diameter X Proxy" where Calhoun et al. expires November 2002 [Page 17] Internet-Draft June 2002 X is the application which it supports, and not a "Diameter Proxy." The base Diameter protocol concerns itself with capabilities negotiation, how messages are sent and how peers may eventually be abandoned. The base protocol also defines certain rules that apply to all exchanges of messages between Diameter nodes. Communication between Diameter peers begins with one peer sending a message to another Diameter peer. The set of AVPs included in the message is determined by a particular Diameter application. One AVP that is included to reference a user's session is the Session-Id. The initial request for authentication and/or authorization of a user would include the Session-Id. The Session-Id is then used in all subsequent messages to identify the user's session (see section 8 for more information). The communicating party may accept the request, or reject it by returning an answer message with the Result-Code AVP set to indicate an error occurred. The specific behavior of the Diameter server or client receiving a request depends on the Diameter application employed. Session state (associated with a Session-Id) MUST be freed upon receipt of the Session-Termination-Request, Session-Termination- Answer, expiration of authorized service time in the Session-Timeout AVP, and according to rules established in a particular Diameter application. 2.1 Transport The base Diameter protocol is run on port TBD of both TCP [TCP] and SCTP [SCTP] transport protocols (for interoperability test purposes port 1812 will be used until IANA assigns a port to the protocol). Diameter clients MUST support either TCP or SCTP, while agents and servers MUST support both. Future versions of this specification MAY mandate that clients support SCTP. A Diameter node MAY initiate connections from a source port other than the one that it declares it accepts incoming connections on, and MUST be prepared to receive connections on port TBD. A given Diameter instance of the peer state machine MUST NOT use more than one transport connection to communicate with a given peer, unless multiple instances exist on the peer in which case a separate connection per process is allowed. When no transport connection exists with a peer, an attempt to connect SHOULD be periodically attempted. This behavior is handled Calhoun et al. expires November 2002 [Page 18] Internet-Draft June 2002 via the Tc timer, who's recommended value is 30 seconds. There are certain exceptions to this rule, such as when a peer has terminated the transport connection stating that it does not wish to communicate. When connecting to a peer and either zero or more transports are specified, SCTP SHOULD be tried first, followed by TCP. See section 5.2 for more information on peer discovery. Diameter implementations SHOULD be able to interpret ICMP protocol port unreachable messages as explicit indications that the server is not reachable, subject to security policy on trusting such messages. Diameter implementations SHOULD also be able to interpret ECONNREFUSED (a reset from the transport) and timed-out connection attempts. If Diameter receives data up from TCP that cannot be parsed or identified as a Diameter error made by the peer, the stream is compromised and cannot be recovered. The transport connection MUST be closed using a RESET call (graceful closure is also compromised). 2.1.1 SCTP Guidelines The following are guidelines for Diameter implementations that support SCTP: 1. For interoperability: All Diameter nodes MUST be prepared to receive Diameter messages on any SCTP stream in the association. 2. To prevent blocking: All Diameter nodes SHOULD utilize all SCTP streams available to the association to prevent head-of-the- line blocking. 2.2 Securing Diameter Messages Diameter clients, such as Network Access Servers (NASes) and Mobility Agents MUST support IP Security [SECARCH], and MAY support TLS [TLS]. Diameter servers MUST support TLS and IPsec. The Diameter protocol MUST NOT be used without any security mechanism (TLS or IPsec). It is suggested that IPsec can be used primarily at the edges and in intra-domain traffic, such as using pre-shared keys between a NAS a local AAA proxy. This also eases the requirements on the NAS to support certificates. It is also suggested that inter-domain traffic would primarily use TLS. See sections 13.1 and 13.2 for more details on IPsec and TLS usage. Calhoun et al. expires November 2002 [Page 19] Internet-Draft June 2002 2.3 Diameter Application Compliance Application Identifiers are advertised during the capabilities exchange phase (see section 5.3). For a given application, there are two different ways of advertising support. First, advertising support of the application via the Auth-Application-Id implies that the sender supports all authentication and authorization command codes, and the AVPs specified in the associated ABNFs, described in the specification. Second, advertising support of the application via the Acct-Application-Id implies that the sender supports the Accounting command codes defined in this specification, as well as the accounting AVPs defined in the application's specification. An implementation MAY add arbitrary AVPs to any command defined in an application, including vendor-specific AVPs. Please refer to section 11.1.1 for details. 2.4 Application Identifiers Each Diameter application MUST have an IANA assigned Application Identifier (see section 11.3). The base protocol does not require an Application Identifier since its support is mandatory. During the capabilities exchange, Diameter nodes inform their peers of locally supported applications. Furthermore, all Diameter messages contain an Application Identifier, which is used in the message forwarding process. The following Application Identifier values are defined: NASREQ 1 [NASREQ] Mobile-IP 4 [DIAMMIP] Relay 0xffffffff Relay and redirect agents MUST advertise the Relay Application Identifier, accounting servers capable of storing any records MUST advertise the Relay Application Identifier for accounting, while all other Diameter nodes MUST advertise locally supported applications. The receiver of a Capabilities Exchange message advertising Relay service MUST assume that the sender supports all current and future applications. Diameter relay and proxy agents are responsible for finding an upstream server that supports the application of a particular message. If none can be found, an error message is returned with the Result-Code AVP set to DIAMETER_UNABLE_TO_DELIVER. Calhoun et al. expires November 2002 [Page 20] Internet-Draft June 2002 2.5 Connections vs. Sessions This section attempts to provide the reader with an understanding of the difference between connection and session, which are terms used extensively throughout this document. A connection is a transport level connection between two peers, used to send and receive Diameter messages. A session is a logical concept at the application layer, and is shared between an access device and a server, and is identified via the Session-Id AVP +--------+ +-------+ +--------+ | Client | | Relay | | Server | +--------+ +-------+ +--------+ <----------> <----------> peer connection A peer connection B <-----------------------------> User session x Figure 1: Diameter connections and sessions In the example provided in Figure 1, peer connection A is established between the Client and its local Relay. Peer connection B is established between the Relay and the Server. User session X spans from the Client via the Relay to the Server. Each "user" of a service causes an auth request to be sent, with a unique session identifier. Once accepted by the server, both the client and the server are aware of the session. It is important to note that there is no relationship between a connection and a session, and that Diameter messages for multiple sessions are all multiplexed through a single connection. 2.6 Peer Table The Diameter Peer Table is used in message forwarding, and referenced by the Realm Routing Table. A Peer Table entry contains the following fields: - Host identity. following the conventions described for the DiameterIdentity derived AVP data format in section 4.4. This field contains the contents of the Origin-Host AVP found in the CER or CEA message. - Status. This is the state of the peer entry, and MUST match one of the values listed in section 5.6. - Static or Dynamic. Specifies whether a peer entry was statically configured, or dynamically discovered. - Expiration time. Specifies the time at which dynamically discovered peer table entries are to be either refreshed, or Calhoun et al. expires November 2002 [Page 21] Internet-Draft June 2002 expired. - TLS Enabled. Specifies whether TLS is to be used when communicating with the peer. - Additional security information, when needed (e.g. keys, certificates) 2.7 Realm-Based Routing Table All Realm-Based routing lookups are performed against what is commonly known as the Realm Routing Table (see section 12). A Realm Routing Table Entry contains the following fields: - Realm Name. This is the field that is typically used as a primary key in the routing table lookups. Note that some implementations perform their lookups based on longest-match- from-the-right on the realm rather than requiring an exact match. - Application Identifier. An application is identified by a vendor id and an application id. For all IETF standards track Diameter applications, the vendor id is zero . A route entry can have a different destination based on the application identification avp of the message. This is one of Acct-Application-Id (for accounting messages), Auth-Application-Id (for non-accounting messages) or Vendor-Specific-Application-Id (for vendor specific messages). This field MUST be used as a secondary key field in routing table lookups. - Local Action. The Local Action field is used to identify how a message should be treated. The following actions are supported: 1. LOCAL - Diameter messages that resolve to a route entry with the Local Action set to Local can be satisfied locally, and do not need to be routed to another server. 2. RELAY - All Diameter messages that fall within this category MUST be routed to a next hop server, without modifying any non-routing AVPs. See section 6.1.8 for relaying guidelines 3. PROXY - All Diameter messages that fall within this category MUST be routed to a next hop server. The local server MAY apply its local policies to the message by including new AVPs to the message prior to routing. See section 6.1.8 for proxying guidelines. 4. REDIRECT - Diameter messages that fall within this category MUST have the identity of the home Diameter server(s) appended, and returned to the sender of the message. See section 6.1.7 for redirect guidelines. - Server Identifier. One or more servers the message is to be routed to. These servers MUST also be present in the Peer table. When the Local Action is set to RELAY or PROXY, this field Calhoun et al. expires November 2002 [Page 22] Internet-Draft June 2002 contains the identity of the server(s) the message must be routed to. When the Local Action field is set to REDIRECT, this field contains the identity of one or more servers the message should be redirected to. - Static or Dynamic. Specifies whether a route entry was statically configured, or dynamically discovered. - Expiration time. Specifies the time which a dynamically discovered route table entry expires. It is important to note that Diameter agents MUST support at least one of the LOCAL, RELAY, PROXY or REDIRECT modes of operation. Agents do not need to support all modes of operation in order to conform with the protocol specification, but MUST follow the protocol compliance guidelines in section 2. Relay agents MUST NOT reorder AVPs, and proxies MUST NOT reorder AVPs. The routing table MAY include a default entry that MUST be used for any requests not matching any of the other entries. The routing table MAY consist of only such an entry. When a request is routed, the target server MUST have advertised the Application Identifier (see section 2.4) for the given message, or have advertised itself as a relay or proxy agent. Otherwise, an error is returned with the Result-Code AVP set to DIAMETER_UNABLE_TO_DELIVER. 2.8 Role of Diameter Agents In addition to client and servers, the Diameter protocol introduces relay, proxy, redirect, and translation agents, each of which is defined in Section 1.4. These Diameter agents are useful for several reasons: - They can distribute administration of systems to a configurable grouping, including the maintenance of security associations. - They can be used for concentration of requests from an number of co-located or distributed NAS equipment sets to a set of like user groups. - They can do value-added processing to the requests or responses. - They can be used for load balancing. - A complex network will have multiple authentication sources, they can sort requests and forward towards the correct target. The Diameter protocol requires that agents maintain transaction state, which is used for failover purposes. Transaction state implies that upon forwarding a request, its Hop-by-Hop identifier is saved; the field is replaced with a locally unique identifier, which is Calhoun et al. expires November 2002 [Page 23] Internet-Draft June 2002 restored to its original value when the corresponding answer is received. The request's state is released upon receipt of the answer. A stateless agent is one that only maintains transaction state. The Proxy-Info AVP allows stateless agents to add local state to a Diameter request, with the guarantee that the same state will be present in the answer. However, the protocol's failover procedures require that agents maintain a copy of pending requests. A stateful agent is one that maintains session state information; by keeping track of all authorized active sessions. Each authorized session is bound to a particular service, and its state is considered active either until it is notified otherwise, or by expiration. Each authorized session has an expiration, which is communicated by Diameter servers via the Session-Timeout AVP. Maintaining session state MAY be useful in certain applications, such as: - Protocol translation (e.g. RADIUS <-> Diameter) - Limiting resources authorized to a particular user - Per user or transaction auditing A Diameter agent MAY act in a stateful manner for some requests and be stateless for others. A Diameter implementation MAY act as one type of agent for some requests, and as another type of agent for others. 2.8.1 Relay Agents Relay Agents are Diameter agents that accept requests and route messages to other Diameter nodes based on information found in the messages (e.g. Destination-Realm). This routing decision is performed using a list of supported realms, and known peers. This is known as the Realm Routing Table, as is defined further in section 2.7. Relays MAY be used to aggregate requests from multiple Network Access Servers (NASes) within a common geographical area (POP). The use of Relays is advantageous since it eliminates the need for NASes to be configured with the necessary security information they would otherwise require to communicate with Diameter servers in other realms. Likewise, this reduces the configuration load on Diameter servers that would otherwise be necessary when NASes are added, changed or deleted. Relays modify Diameter messages by inserting, and removing routing information, but do not modify any other portion of a message. Calhoun et al. expires November 2002 [Page 24] Internet-Draft June 2002 Further, Relays' inherent simplicity implies that they are stateless and therefore SHOULD NOT maintain session state but MUST maintain transaction state. +------+ ---------> +------+ ---------> +------+ | | 1. Request | | 2. Request | | | NAS | | DRL | | HMS | | | 4. Answer | | 3. Answer | | +------+ <--------- +------+ <--------- +------+ mno.net mno.net abc.com Figure 2: Relaying of Diameter messages The example provided in Figure 2 depicts a request issued from NAS, which is an access device, for the user bob@abc.com. Prior to issuing the request, NAS performs a Diameter route lookup, using "abc.com" as the key, and determines that the message is to be relayed to DRL, which is a Diameter Relay. DRL performs the same route lookup as NAS, and relays the message to HMS, which is abc.com's Home Diameter Server. HMS identifies that the request can be locally supported (via the realm), processes the authentication and/or authorization request, and replies with an answer, which is routed back to NAS using saved transaction state. Since Relays do not perform any application level processing, they provide relaying services for all Diameter applications, and therefore MUST advertise the Relay Application Identifier. 2.8.2 Proxy Agents Similarly to Relays, Proxy agents route Diameter messages using the Diameter Routing Table. However, they differ since they modify messages to implement policy enforcement. This requires that proxies maintain the state of their downstream peers (e.g. access devices) to enforce resource usage, provide admission control, and provisioning. It is important to note that although proxies MAY provide a value-add function for NASes, they do not allow access devices to use end-to- end security, since modifying messages breaks authentication. Proxies MAY be used in call control centers or access ISPs that provide outsourced connections, they can monitor the number and types of ports in use, and make allocation and admission decisions according to their configuration. Proxies that wish to limit resources MUST be stateful, and all Proxies MUST maintain transaction state. Calhoun et al. expires November 2002 [Page 25] Internet-Draft June 2002 Since enforcing policies requires an understanding of the service being provided, Proxies MUST only advertise the Diameter applications they support. 2.8.3 Redirect Agents Redirect agents provide Realm to Server address resolution and MAY also provide User to Server address resolution. These redirect agents would make use of the Diameter routing table or optionally, a user table to determine where a given request should be forwarded. When a request is received by a redirect agent, a special answer is created, which includes the identity of the Diameter server(s) the originator of the request should contact directly. Redirect agents are useful in scenarios where the Diameter routing configuration needs to be centralized. An example is a redirect agent that provides services to all members of a consortium, but does not wish to be burdened with relaying all messages between realms. This scenario is advantageous since it does not require that the consortium provide routing updates to its members when changes are made to a member's infrastructure. Since redirect agents do not relay messages, and only return an answer with the information necessary for Diameter agents to communicate directly, they do not modify messages. Since redirect agents do not receive answer messages, they cannot maintain session state. Further, since redirect agents never relay requests, they are not required to maintain transaction state. The example provided in Figure 3 depicts a request issued from the access device, NAS, for the user bob@abc.com. The message is forwarded by the NAS to its relay, DRL, which does not have a routing entry in its Diameter Routing Table for abc.com. DRL has a default route configured to DRD, which is a redirect agent that returns a redirect notification to DRL, as well as HMS' contact information. Upon receipt of the redirect notification, DRL establishes a transport connection with HMS, if one doesn't already exist, and forwards the request to it. Calhoun et al. expires November 2002 [Page 26] Internet-Draft June 2002 +------+ | | | DRD | | | +------+ ^ | 2. Request | | 3. Redirection | | Notification | v +------+ ---------> +------+ ---------> +------+ | | 1. Request | | 4. Request | | | NAS | | DRL | | HMS | | | 6. Answer | | 5. Answer | | +------+ <--------- +------+ <--------- +------+ mno.net mno.net abc.com Figure 3: Redirecting a Diameter Message Since Redirect agents do not perform any application level processing, they provide relaying services for all Diameter applications, and therefore MUST advertise the Relay Application Identifier. 2.8.4 Translation Agents A Translation Agent is a device that provides translation between two protocols (e.g. RADIUS<->Diameter, TACACS+<->Diameter). Translation agents are likely to be used as aggregation servers to communicate with a Diameter infrastructure, while allowing for the embedded systems to be migrated at a slower pace. Given that the Diameter protocol introduces the concept of long-lived authorized sessions, translation agents MUST be session stateful and MUST maintain transaction state. Translation of messages can only occur if the agent recognizes the application of a particular request, and therefore translation agents MUST only advertise their locally supported applications. +------+ ---------> +------+ ---------> +------+ | | RADIUS Request | | Diameter Request | | | NAS | | TLA | | HMS | | | RADIUS Answer | | Diameter Answer | | +------+ <--------- +------+ <--------- +------+ mno.net mno.net abc.com Figure 4: Translation of RADIUS to Diameter 2.9 End-to-End Security Framework Calhoun et al. expires November 2002 [Page 27] Internet-Draft June 2002 The basic components of end-to-end security include encryption and message origin authentication, or in otherwords, AVP integrity and confidentiality between two peers communicating through agents. End-to-end security can be provided by an end-to-end security extension, which is not defined in the base protocol specification. There is ongoing work toward an end-to-end security session [AAACMS] The circumstances requiring the use of end-to-end security are determined by service provider policy. This policy is not the subject of standardization. This policy may be indexed by next hop Diameter peer or by destination realm. For example, use of TLS or IPsec for Diameter peers communicating in on a peer-to-peer basis, without relays or proxies may be sufficient in many cases. The use of end-to-end security can be classified as the following: - Never use end-to-end security. - Use end-to-end security on messages containing sensitive AVPs. Which AVPs are sensitive is determined by service provider policy. AVPs containing keys and passwords should be considered sensitive. Accounting AVPs may be considered sensitive. Any AVP for which the P bit may be set or which may be encrypted may be considered sensitive. Always use end-to-end security. It is strongly recommended that all Diameter implementations support end-to-end security. 3 Diameter Header A summary of the Diameter header format is shown below. The fields are transmitted in network byte order. Calhoun et al. expires November 2002 [Page 28] Internet-Draft June 2002 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ver | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |R P E r r r r r| Command-Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vendor-ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Hop-by-Hop Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | End-to-End Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | AVPs ... +-+-+-+-+-+-+-+-+-+-+-+-+- Version This Version field MUST be set to 1 to indicate Diameter Version 1. Message Length The Message Length field is three octets and indicates the length of the Diameter message including the header fields. Command Flags The Command Flags field is eight bits. The following bits are assigned: R(equest) - If set, the message is a request. If cleared, the message is an answer. P(roxiable) - If set, the message MAY be proxied, relayed or redirected. If cleared, the message MUST be locally processed. E(rror) - If set, the message contains a protocol error, and the message will not conform to the ABNF described for this command. Messages with the 'E' bit set are commonly referred to as an error messages. This bit MUST NOT be set in request messages. See section 7.2. r(eserved) - these flag bits are reserved for future use, and MUST be set to zero, otherwise an error MUST be sent to the sender. Command-Code The Command-Code field is three octets, and is used in order to communicate the command associated with the message. The 24-bit address space is managed by IANA (see section 11.2). Calhoun et al. expires November 2002 [Page 29] Internet-Draft June 2002 Vendor-ID In the event that the Command-Code field contains a vendor specific command, the four-octet Vendor-ID field contains the IANA assigned "SMI Network Management Private Enterprise Codes" [ASSIGNNO] value. If the Command-Code field contains an IETF standard Command, the Vendor-ID field MUST be set to zero (0). Any vendor wishing to implement a vendor-specific Diameter command MUST use their own Vendor-ID along with their privately managed Command-Code address space, guaranteeing that they will not collide with any other vendor's vendor-specific command, nor with future IETF applications. All vendor-specific Diameter commands require Informational RFCs documenting the command unless for Private Use as described in Section 11.1.1. Hop-by-Hop Identifier The Hop-by-Hop Identifier is an unsigned 32-bit integer field (in network byte order) and aids in matching requests and replies. The sender MUST ensure that the Hop-by-Hop identifier in a request is unique on a given connection at any given time, and MAY attempt to ensure that the number is unique across reboots. The sender of an Answer message MUST ensure that the Hop-by-Hop Identifier field contains the same value that was found in the corresponding request. The Hop-by-Hop identifier is normally a monotonically increasing number, whose start value was randomly generated. An answer message that is received with an unknown Hop-by-Hop Identifier MUST be discarded. End-to-End Identifier The End-to-End Identifier is an unsigned 32-bit integer field (in network byte order) and is used to detect duplicate messages. Upon reboot implementations MAY set the high order 12 bits to contain the low order 12 bits of current time, and the low order 20 bits to a random value. Senders of request messages MUST insert a unique identifier on each message. The identifier MUST remain locally unique for a period of at least 4 minutes, even across reboots. The originator of an Answer message MUST ensure that the End-to-End Identifier field contains the same value that was found in the corresponding request. The End-to-End Identifier MUST NOT be modified by relay agents. The combination of the Origin-Host and this field is used to detect duplicates. Duplicate requests SHOULD cause the same answer to be transmitted (modulo the hop- by-hop Identifier field and any routing AVPs that may be present), and MUST NOT affect any state that was set when the original request was processed. Duplicate answer messages that are to be locally consumed (see Section 6.2) SHOULD be silently discarded. AVPs AVPs are a method of encapsulating information relevant to the Calhoun et al. expires November 2002 [Page 30] Internet-Draft June 2002 Diameter message. See section 4 for more information on AVPs. 3.1 Command Codes Each command Request/Answer pair is assigned a command code, and the sub-type (i.e. - request or answer) is identified via the 'R' bit in the Command Flags field of the Diameter header. Every Diameter message MUST contain a command code in its header's Command-Code field, which is used to determine the action that is to be taken for a particular message. The following Command Codes are defined in the Diameter base protocol: Command-Name Abbrev. Code Reference -------------------------------------------------------- Abort-Session-Request ASR 274 8.5.1 Abort-Session-Answer ASA 274 8.5.2 Accounting-Request ACR 271 9.7.1 Accounting-Answer ACA 271 9.7.2 Capabilities-Exchange- CER 257 5.3.1 Request Capabilities-Exchange- CEA 257 5.3.2 Answer Device-Watchdog-Request DWR 280 5.5.1 Device-Watchdog-Answer DWA 280 5.5.2 Disconnect-Peer-Request DPR 282 5.4.1 Disconnect-Peer-Answer DPA 282 5.4.2 Re-Auth-Request RAR 258 8.3.1 Re-Auth-Answer RAA 258 8.3.2 Session-Termination- STR 275 8.4.1 Request Session-Termination- STA 275 8.4.2 Answer 3.2 Command Code ABNF specification Every Command Code defined MUST include a corresponding ABNF specification, which is used to define the AVPs that MUST or MAY be present. The following format is used in the definition: command-def = command-name "::=" diameter-message command-name = diameter-name diameter-name = ALPHA *(ALPHA / DIGIT / "-") Calhoun et al. expires November 2002 [Page 31] Internet-Draft June 2002 diameter-message = header [ *fixed] [ *required] [ *optional] [ *fixed] header = "<" Diameter-Header:" [vendor-id] command-id [r-bit] [p-bit] [e-bit] ">" vendor-id = 1*DIGIT ":" ; The optional vendor-id is used to define ; vendor specific commands command-id = 1*DIGIT ; The Command Code assigned to the command r-bit = ", REQ" ; If present, the 'R' bit in the Command ; Flags is set, indicating that the message ; is a request, as opposed to an answer. p-bit = ", PXY" ; If present, the 'P' bit in the Command ; Flags is set, indicating that the message ; is proxiable. e-bit = ", ERR" ; If present, the 'E' bit in the Command ; Flags is set, indicating that the answer ; message contains a Result-Code AVP in ; the "protocol error" class. fixed = [qual] "<" avp-spec ">" ; Defines the fixed position of an AVP required = [qual] "{" avp-spec "}" ; The AVP MUST be present and can appear ; anywhere in the message. optional = [qual] "[" avp-name "]" ; The avp-name in the 'optional' rule cannot ; evaluate to any AVP Name which is included ; in a fixed or required rule. The AVP can ; appear anywhere in the message. qual = [min] "*" [max] ; See ABNF conventions, RFC 2234 section 6.6. ; The absence of any qualifiers depends on whether ; it precedes a fixed, required, or optional ; rule. If a fixed or required rule has no ; qualifier, then exactly one such AVP MUST Calhoun et al. expires November 2002 [Page 32] Internet-Draft June 2002 ; be present. If an optional rule has no ; qualifier, then 0 or 1 such AVP may be ; present. ; ; NOTE: "[" and "]" have a different meaning ; than in ABNF (see the optional rule, above). ; These braces cannot be used to express ; optional fixed rules (such as an optional ; ICV at the end.) To do this, the convention ; is '0*1fixed'. min = 1*DIGIT ; The minimum number of times the element may ; be present. The default value is zero. max = 1*DIGIT ; The maximum number of times the element may ; be present. The default value is infinity. A ; value of zero implies the AVP MUST NOT be ; present. avp-spec = diameter-name ; The avp-spec has to be an AVP Name, defined ; in the base or extended Diameter ; specifications. avp-name = avp-spec / "AVP" ; The string "AVP" stands for *any* arbitrary ; AVP Name, which does not conflict with the ; required or fixed position AVPs defined in ; the command code definition. The following is a definition of a fictitious command code: Example-Request ::= < "Diameter-Header: 9999999, REQ, PXY > { User-Name } * { Origin-Host } * [ AVP ] 3.3 Diameter Command Naming Conventions Diameter commands typically includes one or more English words followed by the verb Request or Answer. Each English word is delimited by a hyphen. A three-letter acronym for both the request and answer is also normally provided. An example is a message set used to terminate a session. The command Calhoun et al. expires November 2002 [Page 33] Internet-Draft June 2002 name is Session-Terminate-Request and Session-Terminate-Answer, while the acronyms are STR and STA, respectively. Both the request and the answer for a given command share the same command code. The request is identified by the R(equest) bit in the Diameter header set to one (1), to ask that a particular action be performed, such as authorizing a user or terminating a session. Once the receiver has completed the request it issues the corresponding answer, which includes a result code that communicates one of the following: - The request was successful - The request failed - An additional request must be sent to provide information the peer requires prior to returning a successful or failed answer. - The receiver could not process the request, but provides information about a Diameter peer that is able to satisfy the request, known as redirect. Additional information, encoded within AVPs, MAY also be included in answer messages. 4 Diameter AVPs Diameter AVPs carry specific authentication, accounting, authorization, routing and security information as well as configuration details for the request and reply. Some AVPs MAY be listed more than once. The effect of such an AVP is specific, and is specified in each case by the AVP description. Each AVP of type OctetString MUST be padded to align on a 32-bit boundary, while other AVP types align naturally. Zero bytes are added to the end of the AVP Data field till a word boundary is reached. The length of the padding is not reflected in the AVP Length field. 4.1 AVP Header The fields in the AVP header MUST be sent in network byte order. The format of the header is: Calhoun et al. expires November 2002 [Page 34] Internet-Draft June 2002 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | AVP Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |V M P r r r r r| AVP Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vendor-ID (opt) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Data ... +-+-+-+-+-+-+-+-+ AVP Code The AVP Code, combined with the Vendor-Id field, identifies the attribute uniquely. AVP numbers 0 through 255, with the Vendor-Id set to zero (0) are reserved for backward compatibility with RADIUS. AVP numbers 256 and above are used for Diameter, which are allocated by IANA (see section 11.1). AVP Flags The AVP Flags field informs the receiver how each attribute must be handled. The 'r' (reserved) bits are unused and SHOULD be set to 0. Note that subsequent Diameter applications MAY define additional bits within the AVP Header, and an unrecognized bit SHOULD be considered an error. The 'P' bit indicates the need for encryption for end-to-end security. The 'M' Bit, known as the Mandatory bit, indicates whether support of the AVP is required. If an AVP with the 'M' bit set is received by a Diameter client, server, proxy, or translation agent and either the AVP or its value is unrecognized, the message MUST be rejected. Diameter Relay and Redirect agents MUST NOT reject messages with unrecognized AVPs. The 'M' bit MUST be set according to the rules defined for the AVP containing it. In order to preserve interoperability, a Diameter implementation MUST be able to exclude from a Diameter message any Mandatory AVP which is neither defined in the base Diameter standard nor in any of the Diameter Application specifications governing the message in which it appears. It MAY do this in one of the following ways: 1) If a message is rejected because it contains a Mandatory AVP which is neither defined in the base Diameter standard nor in any of the Diameter Application specifications governing the message in which it appears, the implementation may resend the message without the AVP, possibly inserting additional standard AVPs instead. Calhoun et al. expires November 2002 [Page 35] Internet-Draft June 2002 2) A configuration option may be provided on a system wide, per peer, or per realm basis that would allow/prevent particular Mandatory AVPs to be sent. Thus an administrator could change the configuration to avoid interoperability problems. Diameter implementations are required to support all Mandatory AVPs which are allowed by the message's formal syntax and defined either in the base Diameter standard or in one of the Diameter Application specifications governing the message. AVPs with the 'M' bit cleared are informational only and a receiver that receives a message with such an AVP that is not supported, or whose value is not supported, MAY simply ignore the AVP. The 'V' bit, known as the Vendor-Specific bit, indicates whether the optional Vendor-ID field is present in the AVP header. When set the AVP Code belongs to the specific vendor code address space. Unless otherwise noted, AVPs will have the following default AVP Flags field settings: The 'M' bit MUST be set. The 'V' bit MUST NOT be set. AVP Length The AVP Length field is three octets, and indicates the number of octets in this AVP including the AVP Code, AVP Length, AVP Flags, Vendor-ID field (if present) and the AVP data. If a message is received with an invalid attribute length, the message SHOULD be rejected. 4.2 Optional Header Elements The AVP Header contains one optional field. This field is only present if the respective bit-flag is enabled. Vendor-ID The Vendor-ID field is present if the 'V' bit is set in the AVP Flags field. The optional four-octet Vendor-ID field contains the IANA assigned "SMI Network Management Private Enterprise Codes" [ASSIGNNO] value, encoded in network byte order. Any vendor wishing to implement a vendor-specific Diameter AVP MUST use their own Vendor-ID along with their privately managed AVP address space, guaranteeing that they will not collide with any other vendor's vendor-specific AVP, nor with future IETF applications. Calhoun et al. expires November 2002 [Page 36] Internet-Draft June 2002 A vendor ID value of zero (0) corresponds to the IETF adopted AVP values, as managed by the IANA. Since the absence of the vendor ID field implies that the AVP in question is not vendor specific, implementations MUST NOT use the zero (0) vendor ID. 4.3 Basic AVP Data Formats The Data field is zero or more octets and contains information specific to the Attribute. The format and length of the Data field is determined by the AVP Code and AVP Length fields. The format of the Data field MUST be one of the following base data types or a data type derived from the base data types. In the event that a new Basic AVP Data Format is needed, a new version of this RFC must be created. OctetString The data contains arbitrary data of variable length. Unless otherwise noted, the AVP Length field MUST be set to at least 8 (12 if the 'V' bit is enabled). AVP Values of this type that are not a multiple of four-octets in length is followed by the necessary padding so that the next AVP (if any) will start on a 32-bit boundary. Integer32 32 bit signed value, in network byte order. The AVP Length field MUST be set to 12 (16 if the 'V' bit is enabled). Integer64 64 bit signed value, in network byte order. The AVP Length field MUST be set to 16 (20 if the 'V' bit is enabled). Unsigned32 32 bit unsigned value, in network byte order. The AVP Length field MUST be set to 12 (16 if the 'V' bit is enabled). Unsigned64 64 bit unsigned value, in network byte order. The AVP Length field MUST be set to 16 (20 if the 'V' bit is enabled). Float32 This represents floating point values of single precision as described by [FLOATPOINT]. The 32-bit value is transmitted in network byte order. The AVP Length field MUST be set to 12 (16 if the 'V' bit is enabled). Float64 This represents floating point values of double precision as described by [FLOATPOINT]. The 64-bit value is transmitted in Calhoun et al. expires November 2002 [Page 37] Internet-Draft June 2002 network byte order. The AVP Length field MUST be set to 16 (20 if the 'V' bit is enabled). Grouped The Data field is specified as a sequence of AVPs. Each of these AVPs follows - in the order in which they are specified - including their headers and padding. The AVP Length field is set to 8 (12 if the 'V' bit is enabled) plus the total length of all included AVPs, including their headers and padding. Thus the AVP length field of an AVP of type Grouped is always a multiple of 4. 4.4 Derived AVP Data Formats In addition to using the Basic AVP Data Formats, applications may define data formats derived from the Basic AVP Data Formats. An application that defines new AVP Derived Data Formats MUST include them in a section entitled "AVP Derived Data Formats", using the same format as the definitions below. Each new definition must be either defined or listed with a reference to the RFC that defines the format. The below AVP Derived Data Formats are commonly used by applications. IPAddress The IPAddress format is derived from the OctetString AVP Base Format. It represents 32 bit (IPv4) [IPV4] or 128-bit (IPv6) [IPV6] address, most significant octet first. The format of the address (IPv4 or IPv6) is determined by the length. If the attribute value is an IPv4 address, the AVP Length field MUST be 12 (16 if 'V' bit is enabled); otherwise, the AVP Length field MUST be set to 24 (28 if the 'V' bit is enabled) for IPv6 addresses. Time The Time format is derived from the OctetString AVP Base Format. The string MUST contain four octets, in the same format as the first four bytes are in the NTP timestamp format. The NTP Timestamp format is defined in chapter 3 of [SNTP]. This represents the number of seconds since 0h on 1 January 1900 with respect to the Coordinated Universal Time (UTC). On 6h 28m 16s UTC, 7 February 2036 the time value will overflow. SNTP [SNTP] describes a procedure to extend the time to 2104. This procedure MUST be supported by all DIAMETER nodes. Calhoun et al. expires November 2002 [Page 38] Internet-Draft June 2002 UTF8String The UTF8String format is derived from the OctetString AVP Base Format. This is a human readable string represented using the ISO/IEC IS 10646-1 character set, encoded as an OctetString using the UTF-8 [UFT8] transformation format described in RFC 2279. Since additional code points are added by amendments to the 10646 standard from time to time, implementations MUST be prepared to encounter any code point from 0x00000001 to 0x7fffffff. Byte sequences that do not correspond to the valid encoding of a code point into UTF-8 charset or are outside this range are prohibited. The use of control codes SHOULD be avoided. When it is necessary to represent a newline, the control code sequence CR LF SHOULD be used. The use of leading or trailing white space SHOULD be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, MAY be provided. For information encoded in 7-bit US-ASCII, the UTF-8 charset is identical to the US-ASCII charset. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of an UTF8String in octets may be different from the number of characters encoded. Note that the AVP Length field of an UTF8String is measured in octets, not characters. DiameterIdentity The DiameterIdentity format is derived from the OctetString AVP Base Format. It uses the UTF-8 charset and has the same requirements as the UTF8String: DiameterIdentity = fqdn DiameterIdentity value is used to uniquely identify a Diameter node for purposes of duplicate connection and routing loop detection. The DiameterIdentity format is derived from the OctetString Base AVP Format. It uses the UTF-8 charset and has the same requirements as UTF8String. Calhoun et al. expires November 2002 [Page 39] Internet-Draft June 2002 The contents of the string MUST be the fqdn of the Diameter node. If multiple Diameter nodes run on the same host, each Diameter node MUST be assigned a unique DiameterIdentity. If a Diameter node can be identified by several FQDNs, a single FQDN should be picked at startup, and used as the only DiameterIdentity for that node, whatever the connection it is sent on. DiameterURI The DiameterURI MUST follow the Uniform Resource Identifiers (URI) syntax [URI] rules specified below: "aaa://" fqdn [ port ] [ transport ] [ protocol ] ; No transport security "aaas://" fqdn [ port ] [ transport ] [ protocol ] ; Transport security used fqdn = Fully Qualified Host Name port = ":" 1*DIGIT ; One of the ports used to listen for ; incoming connections. ; If absent, ; the default Diameter port (TBD) is ; assumed. transport = ";transport=" transport-protocol ; One of the transports used to listen ; for incoming connections. If absent, ; the default SCTP [SCTP] protocol is ; assumed. UDP MUST NOT be used when ; the aaa-protocol field is set to ; diameter. transport-protocol = ( "tcp" / "sctp" / "udp" ) protocol = ";protocol=" aaa-protocol ; If absent, the default AAA protocol ; is diameter. aaa-protocol = ( "diameter" / "radius" / "tacacs+" ) Calhoun et al. expires November 2002 [Page 40] Internet-Draft June 2002 The following are examples of valid Diameter host identities: aaa://host.abc.com;transport=tcp aaa://host.abc.com:6666;transport=tcp aaa://host.abc.com;protocol=diameter aaa://host.abc.com:6666;protocol=diameter aaa://host.abc.com:6666;transport=tcp;protocol=diameter aaa://host.abc.com:1813;transport=udp;protocol=radius Enumerated Enumerated is derived from the Integer32 AVP Base Format. The definition contains a list of valid values and their interpretation and is described in the Diameter application introducing the AVP. IPFilterRule The IPFilterRule format is derived from the OctetString AVP Base Format. It uses the UTF-8 charset and has the same requirements as the UTF8String. Packets may be filtered based on the following information that is associated with it: Direction (in or out) Source and destination IP address (possibly masked) Protocol Source and destination port (lists or ranges) TCP flags IP fragment flag IP options ICMP types Rules for the appropriate direction are evaluated in order, with the first matched rule terminating the evaluation. Each packet is evaluated once. If no rule matches, the packet is dropped if the last rule evaluated was a permit, and passed if the last rule was a deny. IPFilterRule filters MUST follow the format: action dir proto from src to dst [options] action permit - Allow packets that match the rule. deny - Drop packets that match the rule. dir "in" is from the terminal, "out" is to the terminal. proto An IP protocol specified by number. The "ip" Calhoun et al. expires November 2002 [Page 41] Internet-Draft June 2002 keyword means any protocol will match. src and dst
[ports] The
may be specified as: ipno An IPv4 or IPv6 number in dotted- quad or canonical IPv6 form. Only this exact IP number will match the rule. ipno/bits An IP number as above with a mask width of the form 1.2.3.4/24. In this case, all IP numbers from 1.2.3.0 to 1.2.3.255 will match. The bit width MUST be valid for the IP version and the IP number MUST NOT have bits set beyond the mask. For a match to occur, the same IP version must be present in the packet that was used in describing the IP address. To test for a particular IP version, the bits part can be set to zero. The keyword "any" is 0.0.0.0/0 or the IPv6 equivalent. The keyword "assigned" is the address or set of addresses assigned to the terminal. For IPv4, a typical first rule is often "deny in ip! assigned" The sense of the match can be inverted by preceding an address with the not modifier (!), causing all other addresses to be matched instead. This does not affect the selection of port numbers. With the TCP, UDP and SCTP protocols, optional ports may be specified as: {port/port-port}[,ports[,...]] The '-' notation specifies a range of ports (including boundaries). Fragmented packets that have a non-zero offset (i.e. not the first fragment) will never match a rule that has one or more port specifications. See the frag option for details on matching fragmented packets. Calhoun et al. expires November 2002 [Page 42] Internet-Draft June 2002 options: frag Match if the packet is a fragment and this is not the first fragment of the datagram. frag may not be used in conjunction with either tcpflags or TCP/UDP port specifications. ipoptions spec Match if the IP header contains the comma separated list of options specified in spec. The supported IP options are: ssrr (strict source route), lsrr (loose source route), rr (record packet route) and ts (timestamp). The absence of a particular option may be denoted with a '!'. tcpoptions spec Match if the TCP header contains the comma separated list of options specified in spec. The supported TCP options are: mss (maximum segment size), window (tcp window advertisement), sack (selective ack), ts (rfc1323 timestamp) and cc (rfc1644 t/tcp connection count). The absence of a particular option may be denoted with a '!'. established TCP packets only. Match packets that have the RST or ACK bits set. setup TCP packets only. Match packets that have the SYN bit set but no ACK bit. tcpflags spec TCP packets only. Match if the TCP header contains the comma separated list of flags specified in spec. The supported TCP flags are: fin, syn, rst, psh, ack and urg. The absence of a particular flag may be denoted with a '!'. A rule that contains a tcpflags specification can never match a fragmented packet that has a non-zero offset. See the frag option for details on matching fragmented packets. icmptypes types ICMP packets only. Match if the ICMP type is in Calhoun et al. expires November 2002 [Page 43] Internet-Draft June 2002 the list types. The list may be specified as any combination of ranges or individual types separated by commas. Both the numeric values and the symbolic values listed below can be used. The supported ICMP types are: echo reply (0), destination unreachable (3), source quench (4), redirect (5), echo request (8), router advertisement (9), router solicitation (10), time-to-live exceeded (11), IP header bad (12), timestamp request (13), timestamp reply (14), information request (15), information reply (16), address mask request (17) and address mask reply (18). There is one kind of packet that the access device MUST always discard, that is an IP fragment with a fragment offset of one. This is a valid packet, but it only has one use, to try to circumvent firewalls. An access device that is unable to interpret or apply a deny rule MUST terminate the session. An access device that is unable to interpret or apply a permit rule MAY apply a more restrictive rule. An access device MAY apply deny rules of its own before the supplied rules, for example to protect the access device owner's infrastructure. The rule syntax is a modified subset of ipfw(8) from FreeBSD, and the ipfw.c code may provide a useful base for implementations. QoSFilterRule The QosFilterRule format is derived from the OctetString AVP Base Format. It uses the UTF-8 charset and has the same requirements as the UTF8String. Packets may be marked or metered based on the following information that is associated with it: Direction (in or out) Source and destination IP address (possibly masked) Protocol Source and destination port (lists or ranges) DSCP values (no mask or range) Rules for the appropriate direction are evaluated in order, with the first matched rule terminating the evaluation. Each packet is evaluated once. If no rule matches, the packet is treated as best effort. An access device that is unable to Calhoun et al. expires November 2002 [Page 44] Internet-Draft June 2002 interpret or apply a QoS rule SHOULD NOT terminate the session. QoSFilterRule filters MUST follow the format: action dir proto from src to dst [options] tag - Mark packet with a specific DSCP [DIFFSERV]. The DSCP option MUST be included. meter - Meter traffic. The metering options MUST be included. dir The format is as described under IPFilterRule. proto The format is as described under IPFilterRule. src and dst The format is as described under IPFilterRule. 4.5 Grouped AVP Values The Diameter protocol allows AVP values of type 'Grouped.' This implies that the Data field is actually a sequence of AVPs. It is possible to include an AVP with a Grouped type within a Grouped type, that is, to nest them. AVPs within an AVP of type Grouped have the same padding requirements as non-Grouped AVPs, as defined in section 4. The AVP Code numbering space of all AVPs included in a Grouped AVP is the same as for non-grouped AVPs. Further, if any of the AVPs encapsulated within a Grouped AVP has the 'M' (mandatory) bit set, the Grouped AVP itself MUST also include the 'M' bit set. Every Grouped AVP defined MUST include a corresponding grammar, using ABNF [ABNF] (with modifications), as defined below. grouped-avp-def = name "::=" avp name-fmt = ALPHA *(ALPHA / DIGIT / "-") name = name-fmt ; The name has to be the name of an AVP, ; defined in the base or extended Diameter ; specifications. avp = header [ *fixed] [ *required] [ *optional] Calhoun et al. expires November 2002 [Page 45] Internet-Draft June 2002 [ *fixed] header = "<" "AVP-Header:" avpcode [vendor] ">" avpcode = 1*DIGIT ; The AVP Code assigned to the Grouped AVP vendor = 1*DIGIT ; The Vendor-ID assigned to the Grouped AVP. ; If absent, the default value of zero is ; used. 4.5.1 Example AVP with a Grouped Data type The Example-AVP (AVP Code 999999) is of type Grouped and is used to clarify how Grouped AVP values work. The Grouped Data field has the following ABNF grammar: Example-AVP ::= < AVP Header: 999999 > { Origin-Host } 1*{ Session-Id } *[ AVP ] An Example-AVP with Grouped Data follows. The Origin-Host AVP is required. In this case: Origin-Host = "abc.com". One or more Session-Ids must follow. Here there are two: Session-Id = "grump.abc.com:33041;23432;893;0AF3B81" Session-Id = "grump.abc.com:33054;23561;2358;0AF3B82" optional AVPs included are Recovery-Policy = 2163bc1d0ad82371f6bc09484133c3f09ad74a0dd5346d54195a7cf0b35 2cabc881839a4fdcfbc1769e2677a4c1fb499284c5f70b48f58503a45c5 c2d6943f82d5930f2b7c1da640f476f0e9c9572a50db8ea6e51e1c2c7bd f8bb43dc995144b8dbe297ac739493946803e1cee3e15d9b765008a1b2a cf4ac777c80041d72c01e691cf751dbf86e85f509f3988e5875dc905119 26841f00f0e29a6d1ddc1a842289d440268681e052b30fb638045f7779c 1d873c784f054f688f5001559ecff64865ef975f3e60d2fd7966b8c7f92 Futuristic-Acct-Record = Calhoun et al. expires November 2002 [Page 46] Internet-Draft June 2002 fe19da5802acd98b07a5b86cb4d5d03f0314ab9ef1ad0b67111ff3b90a0 57fe29620bf3585fd2dd9fcc38ce62f6cc208c6163c008f4258d1bc88b8 17694a74ccad3ec69269461b14b2e7a4c111fb239e33714da207983f58c 41d018d56fe938f3cbf089aac12a912a2f0d1923a9390e5f789cb2e5067 d3427475e49968f841 The data for the optional AVPs is represented in hex since the format of these AVPs is neither known at the time of definition of the Example-AVP group, nor (likely) at the time when the example instance of this AVP is interpreted - except by Diameter implementations which support the same set of AVPs. The encoding example illustrates how padding is used and how length fields are calculated. Also note that AVPs may be present in the Grouped AVP value which the receiver cannot interpret (here, the Recover-Policy and Futuristic-Acct-Record AVPs). This AVP would be encoded as follows: Calhoun et al. expires November 2002 [Page 47] Internet-Draft June 2002 0 1 2 3 4 5 6 7 +-------+-------+-------+-------+-------+-------+-------+-------+ 0 | Example AVP Header (AVP Code = 999999), Length = 468 | +-------+-------+-------+-------+-------+-------+-------+-------+ 8 | Origin-Host AVP Header (AVP Code = 264), Length = 19 | +-------+-------+-------+-------+-------+-------+-------+-------+ 16 | 'e' | 'x' | 'a' | 'm' | 'p' | 'l' | 'e' | '.' | +-------+-------+-------+-------+-------+-------+-------+-------+ 24 | 'c' | 'o' | 'm' |Padding| Session-Id AVP Header | +-------+-------+-------+-------+-------+-------+-------+-------+ 32 | (AVP Code = 263), Length = 50 | 'g' | 'r' | 'u' | 'm' | +-------+-------+-------+-------+-------+-------+-------+-------+ . . . +-------+-------+-------+-------+-------+-------+-------+-------+ 64 | 'A' | 'F' | '3' | 'B' | '8' | '1' |Padding|Padding| +-------+-------+-------+-------+-------+-------+-------+-------+ 68 | Session-Id AVP Header (AVP Code = 263), Length = 51 | +-------+-------+-------+-------+-------+-------+-------+-------+ 72 | 'g' | 'r' | 'u' | 'm' | 'p' | '.' | 'e' | 'x' | +-------+-------+-------+-------+-------+-------+-------+-------+ . . . +-------+-------+-------+-------+-------+-------+-------+-------+ 104 | '0' | 'A' | 'F' | '3' | 'B' | '8' | '2' |Padding| +-------+-------+-------+-------+-------+-------+-------+-------+ 112 | Recovery-Policy Header (AVP Code = 8341), Length = 223 | +-------+-------+-------+-------+-------+-------+-------+-------+ 120 | 0x21 | 0x63 | 0xbc | 0x1d | 0x0a | 0xd8 | 0x23 | 0x71 | +-------+-------+-------+-------+-------+-------+-------+-------+ . . . +-------+-------+-------+-------+-------+-------+-------+-------+ 320 | 0x2f | 0xd7 | 0x96 | 0x6b | 0x8c | 0x7f | 0x92 |Padding| +-------+-------+-------+-------+-------+-------+-------+-------+ 328 | Futuristic-Acct-Record Header (AVP Code = 15930), Length = 137| +-------+-------+-------+-------+-------+-------+-------+-------+ 336 | 0xfe | 0x19 | 0xda | 0x58 | 0x02 | 0xac | 0xd9 | 0x8b | +-------+-------+-------+-------+-------+-------+-------+-------+ . . . +-------+-------+-------+-------+-------+-------+-------+-------+ 464 | 0x41 |Padding|Padding|Padding| +-------+-------+-------+-------+ 4.6 Diameter Base Protocol AVPs The following table describes the Diameter AVPs defined in the base protocol, their AVP Code values, types, possible flag values and whether the AVP MAY be encrypted. For the originator of a Diameter message, "MAY Encr" means that if a message containing that AVP is to Calhoun et al. expires November 2002 [Page 48] Internet-Draft June 2002 be sent via a proxy/agent then the message MUST NOT be sent unless there is end-to-end security between the originator and the recipient OR the originator has locally trusted configuration that indicates that end-to-end security is not needed. Similarly, for the originator of a Diameter message, a "P" in the "MAY" column means that if a message containing that AVP is to be sent via a proxy/agent then the message MUST NOT be sent unless there is end-to-end security between the originator and the recipient or the originator has locally trusted configuration that indicates that end-to-end security is not needed. Due to space constraints, the short form DiamIdent is used to represent DiameterIdentity. Calhoun et al. expires November 2002 [Page 49] Internet-Draft June 2002 +---------------------+ | AVP Flag rules | |----+-----+----+-----|----+ AVP Section | | |SHLD| MUST|MAY | Attribute Name Code Defined Data Type |MUST| MAY | NOT| NOT|Encr| -----------------------------------------|----+-----+----+-----|----| Accounting- 85 9.8.2 Unsigned32 | M | P | | V | Y | Interim-Interval | | | | | | Accounting- 483 9.8.7 Unsigned32 | M | P | | V | Y | Realtime-Required | | | | | | Acct- 50 9.8.5 UTF8String | M | P | | V | Y | Multi-Session-Id | | | | | | Accounting- 485 9.8.3 Unsigned32 | M | P | | V | Y | Record-Number | | | | | | Accounting- 480 9.8.1 Enumerated | M | P | | V | Y | Record-Type | | | | | | Accounting- 44 9.8.4 OctetString| M | P | | V | Y | RADIUS-Session-Id | | | | | | Accounting- 287 9.8.6 Unsigned64 | M | P | | V | Y | Sub-Session-Id | | | | | | Acct- 259 6.9 Integer32 | M | P | | V | N | Application-Id | | | | | | Auth- 258 6.8 Integer32 | M | P | | V | N | Application-Id | | | | | | Auth-Request- 274 8.7 Enumerated | M | P | | V | N | Type | | | | | | Authorization- 291 8.9 Unsigned32 | M | P | | V | N | Lifetime | | | | | | Auth-Grace- 276 8.10 Unsigned32 | M | P | | V | N | Period | | | | | | Auth-Session- 277 8.11 Enumerated | M | P | | V | N | State | | | | | | Re-Auth-Request- 285 8.12 Enumerated | M | P | | V | N | Type | | | | | | Class 25 8.20 OctetString| M | P | | V | Y | Destination-Host 293 6.5 DiamIdent | M | P | | V | N | Destination- 283 6.6 UTF8String | M | P | | V | N | Realm | | | | | | Disconnect-Cause 273 5.4.3 Enumerated | M | P | | V | N | Error-Message 281 7.3 OctetString| | P | | V,M | N | Error-Reporting- 294 7.4 UTF8String | | P | | V,M | N | Host | | | | | | Event-Timestamp 55 8.21 Time | M | P | | V | N | Failed-AVP 279 7.5 Grouped | M | P | | V | N | Firmware- 267 5.3.4 Unsigned32 | | | |P,V,M| N | Revision | | | | | | Host-IP-Address 257 5.3.5 IPAddress | M | P | | V | N | -----------------------------------------|----+-----+----+-----|----| Calhoun et al. expires November 2002 [Page 50] Internet-Draft June 2002 +---------------------+ | AVP Flag rules | |----+-----+----+-----|----+ AVP Section | | |SHLD| MUST|MAY | Attribute Name Code Defined Data Type |MUST| MAY | NOT| NOT|Encr| -----------------------------------------|----+-----+----+-----|----| Inband-Security | | | | | | -Id 299 6.10 Unsigned32 | | | | | | Multi-Round- 272 8.19 Unsigned32 | M | P | | V | Y | Time-Out | | | | | | Origin-Host 264 6.3 DiamIdent | M | P | | V | N | Origin-Realm 296 6.4 UTF8String | M | P | | V | N | Origin-State-Id 278 8.16 Unsigned32 | M | P | | V | N | Product-Name 269 5.3.7 UTF8String | | | |P,V,M| N | Proxy-Host 280 6.7.3 DiamIdent | M | | | P,V | N | Proxy-Info 284 6.7.2 Grouped | M | | | P,V | N | Proxy-State 33 6.7.4 OctetString| M | | | P,V | N | Redirect-Host 292 6.12 DiamURI | M | P | | V | N | Redirect-Host- 261 6.13 Enumerated | M | P | | V | N | Usage | | | | | | Redirect-Max- 262 6.14 Unsigned32 | M | P | | V | N | Cache-Time | | | | | | Result-Code 268 7.1 Unsigned32 | M | P | | V | N | Route-Record 282 6.7.1 DiamIdent | M | | | P,V | N | Session-Id 263 8.8 UTF8String | M | P | | V | Y | Session-Timeout 27 8.13 Unsigned32 | M | P | | V | N | Session-Binding 270 8.17 Unsigned32 | M | P | | V | Y | Session-Server- 271 8.18 Enumerated | M | P | | V | Y | Failover | | | | | | Supported- 265 5.3.6 Unsigned32 | M | P | | V | N | Vendor-Id | | | | | | Termination- 295 8.15 Enumerated | M | P | | V | N | Cause | | | | | | User-Name 1 8.14 UTF8String | M | P | | V | Y | Vendor-Id 266 5.3.3 Unsigned32 | M | P | | V | N | Vendor-Specific- 260 6.11 Grouped | M | P | | V | N | Application-Id | | | | | | Vendor-Specific- 297 7.6 Grouped | M | P | | V | N | Result | | | | | | Vendor-Specific- 298 7.7 Unsigned32 | M | P | | V | N | Result-Code | | | | | | -----------------------------------------|----+-----+----+-----|----| 5 Diameter Peers This section describes how Diameter nodes establish connections and communicate with peers. Calhoun et al. expires November 2002 [Page 51] Internet-Draft June 2002 5.1 Peer Connections Although a Diameter node may have many possible peers that it is able to communicate with, it may not be economical to have an established connection to all of them. At a minimum, a Diameter node SHOULD have an established connection with two peers per realm, known as the primary and secondary peers. Of course, a node MAY have additional connections, if it is deemed necessary. Typically, all messages for a realm are sent to the primary peer, but in the event that failover procedures are invoked, any pending requests are sent to the secondary peer. However, implementations are free to load balance requests between a set of peers. Note that a given peer MAY act as a primary for a given realm, while acting as a secondary for another realm. When a peer is deemed suspect, which could occur for various reasons, including not receiving a DWA within an allotted timeframe, no new requests should be forwarded to the peer, but failover procedures are invoked. When an active peer is moved to this mode, additional connections SHOULD be established to ensure that the necessary number of active connections exists. There are two ways that a peer is removed from the suspect peer list: 1. The peer is no longer reachable, causing the transport connection to be shutdown. The peer is moved to the closed state. 2. Three watchdog messages are exchanged with accepted round trip times, and the connection to the peer is considered stabilized. In the event the peer being removed is either the primary or secondary, an alternate peer SHOULD replace the deleted peer, and assume the role of either primary or secondary. 5.2 Diameter Peer Discovery Allowing for dynamic Diameter agent discovery will make it possible for simpler and more robust deployment of Diameter services. In order to promote interoperable implementations of Diameter peer discovery, the following mechanisms are described. These are based on existing IETF standards. The first option (manual configuration) MUST be supported by all DIAMETER nodes, while the latter two options (SRVLOC and DNS) MAY be supported. There are two cases where Diameter peer discovery may be performed. The first is when a Diameter client needs to discover a first-hop Diameter agent. The second case is when a Diameter agent needs to Calhoun et al. expires November 2002 [Page 52] Internet-Draft June 2002 discover another agent - for further handling of a Diameter operation. In both cases, the following 'search order' is recommended: 1. The Diameter implementation consults its list of static (manually) configured Diameter agent locations. These will be used if they exist and respond. 2. The Diameter implementation uses SLPv2 [SLP] to discover Diameter services. The Diameter service template [TEMPLATE] is included in Appendix A. It is recommended that SLPv2 security be deployed (this requires distributing keys to SLPv2 agents). This is discussed further in Appendix A. SLPv2 will allow Diameter implementations to discover the location of Diameter agents in the local site, as well as their characteristics. Diameter agents with specific capabilities (say support for the Mobile IP application) can be requested, and only those will be discovered. 3. The Diameter implementation performs a NAPTR query for a server in a particular realm. The Diameter implementation has to know in advance which realm to look for a Diameter agent in. This could be deduced, for example, from the 'realm' in a NAI that a Diameter implementation needed to perform a Diameter operation on. 3.1 The services relevant for the task of transport protocol selection are those with NAPTR service fields with values "AAA+D2x", where x is a letter that corresponds to a transport protocol supported by the domain. This specification defines D2T for TCP and D2S for SCTP. We also establish an IANA registry for NAPTR service name to transport protocol mappings. These NAPTR records provide a mapping from a domain, to the SRV record for contacting a server with the specific transport protocol in the NAPTR services field. The resource record will contain an empty regular expression and a replacement value, which is the SRV record for that particular transport protocol. If the server supports multiple transport protocols, there will be multiple NAPTR records, each with a different service value. As per RFC 2915 [NAPTR], the client discards any records whose services fields are not applicable. For the purposes of this specification, several rules are defined. 3.2 A client MUST discard any service fields that identify a Calhoun et al. expires November 2002 [Page 53] Internet-Draft June 2002 resolution service whose value is not "D2X", for values of X that indicate transport protocols supported by the client. The NAPTR processing as described in RFC 2915 will result in discovery of the most preferred transport protocol of the server that is supported by the client, as well as an SRV record for the server. The domain suffixes in the NAPTR replacement field SHOULD match the domain of the original query. It is not necessary for the domain suffixes in the NAPTR replacement field to match the domain of the original query. 3.3 If no NAPTR records are found, the requester queries for those address records for the destination address, '_diameter._sctp'.realm or '_diameter._tcp'.realm. Address records include A RR's, AAAA RR's or other similar records, chosen according to the requestor's network protocol capabilities. If the DNS server returns no address records, the requestor gives up. If the server is using a site certificate, the domain name in the query and the domain name in the replacement field MUST both be valid based on the site certificate handed out by the server in the TLS exchange. Similarly, the domain name in the SRV query and the domain name in the target in the SRV record MUST both be valid based on the same site certificate. Otherwise, an attacker could modify the DNS records to contain replacement values in a different domain, and the client could not validate that this was the desired behavior, or the result of an attack. A dynamically discovered peer causes an entry in the Peer Table (see section 2.6) to be created. Note that entries created via DNS MUST expire (or be refreshed) within the DNS TTL. If a peer is discovered outside of the local realm, a routing table entry (see Section 2.7) for the peer's realm is created. The routing table entry's expiration MUST match the peer's expiration value. 5.3 Capabilities Exchange When two Diameter peers establish a transport connection, they MUST exchange the Capabilities Exchange messages, as specified in the peer state machine (see section 5.6). This message allows the discovery of a peer's identity and its capabilities (protocol version number, supported Diameter applications, security model, etc.) The receiver only issues commands to its peers that have advertised Calhoun et al. expires November 2002 [Page 54] Internet-Draft June 2002 support for the Diameter application that defines the command. A Diameter node MUST cache the supported applications in order to ensure that unrecognized commands and/or AVPs are not unnecessarily sent to a peer. A receiver of a Capabilities-Exchange-Req (CER) message that does not have any applications in common with the sender MUST return a Capabilities-Exchange-Answer (CEA) with the Result-Code AVP set to DIAMETER_NO_COMMON_APPLICATION, and SHOULD disconnect the transport layer connection. Note that receiving a CER or CEA from a peer advertising itself as a Relay (see section 2.4) MUST be interpreted as having common applications with the peer. Similarly, a receiver of a Capabilities-Exchange-Req (CER) message that does not have any security model in common with the sender MUST return a Capabilities-Exchange-Answer (CEA) with the Result-Code AVP set to DIAMETER_NO_COMMON_SECURITY, and SHOULD disconnect the transport layer connection. CERs received from unknown peers MAY be silently discarded, or a CEA MAY be issued with the Result-Code AVP set to DIAMETER_UNKNOWN_PEER. In both cases, the transport connection is closed. If the local policy permits receiving CERs from unknown hosts, a successful CEA MAY be returned. If a CER from an unknown peer is answered with a successful CEA, the lifetime of the peer entry is equal to the lifetime of the transport connection. In case of a transport failure, all the pending transactions destined to the unknown peer can be discarded. The CER and CEA messages MUST NOT be proxied, or redirected. Since the CER/CEA messages cannot be proxied, it is still possible that an upstream agent receives a message for which it has no available peers to handle the application that corresponds to the Command-Code. In such instances, the 'E' bit is set in the answer message (see Section 7.2) with the Result-Code AVP set to DIAMETER_UNABLE_TO_DELIVER to inform the downstream to take action (e.g. re-routing request to an alternate peer). With the exception of the Capabilities-Exchange-Request message, a message of type Request that includes the Auth-Application-Id or Acct-Application-Id AVPs, or a message with an application-specific command code, MAY only be forwarded to a host that has explicitly advertised support for the application (or has advertised the Relay Application Identifier). 5.3.1 Capabilities-Exchange-Request Calhoun et al. expires November 2002 [Page 55] Internet-Draft June 2002 The Capabilities-Exchange-Request (CER), indicated by the Command- Code set to 257 and the Command Flags' 'R' bit set, is sent to exchange local capabilities. Upon detection of a transport failure, this message MUST NOT be sent to an alternate peer. When Diameter is run over SCTP [SCTP], which allows fo