Internet-Draft IPv6 VTN Option October 2022
Dong, et al. Expires 27 April 2023 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-6man-enhanced-vpn-vtn-id-02
Published:
Intended Status:
Standards Track
Expires:
Authors:
J. Dong
Huawei Technologies
Z. Li
Huawei Technologies
C. Xie
China Telecom
C. Ma
China Telecom
G. Mishra
Verizon Inc.

Carrying Virtual Transport Network (VTN) Information in IPv6 Extension Header

Abstract

Virtual Private Networks (VPNs) provide different customers with logically separated connectivity over a common network infrastructure. With the introduction and evolvement of 5G and other network scenarios, some existing or new customers may require connectivity services with advanced characteristics comparing to traditional VPNs. Such kind of network service is called enhanced VPNs (VPN+). VPN+ can be used to deliver IETF network slices, and could also be used for other application scenarios.

A Virtual Transport Network (VTN) is a virtual underlay network which consists of a set of dedicated or shared network resources allocated from the physical underlay network, and is associated with a customized logical network topology. VPN+ services can be delivered by mapping one or a group of overlay VPNs to the appropriate VTNs as the virtual underlay. In packet forwarding, some fields in the data packet needs to be used to identify the VTN the packet belongs to, so that the VTN-specific processing can be performed on each node the packet traverses.

This document proposes a new Hop-by-Hop option of IPv6 extension header to carry the VTN related information, which could used to identify the set of network resources allocated to a VTN and the rules for packet processing. The procedure of processing the VTN option is also specified.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 27 April 2023.

Table of Contents

1. Introduction

Virtual Private Networks (VPNs) provide different customers with logically isolated connectivity over a common network infrastructure. With the introduction and evolvement of 5G and other network scenarios, some existing or new customers may require connectivity services with advanced characteristics comparing to traditional VPNs, such as resource isolation from other services or guaranteed performance. Such kind of network service is called enhanced VPN (VPN+). VPN+ service requires the coordination and integration between the overlay VPNs and the capability and resources of the underlay network. VPN+ can be used to deliver IETF network slices [I-D.ietf-teas-ietf-network-slices].

[I-D.ietf-teas-enhanced-vpn] describes a framework and the candidate component technologies for providing VPN+ services. It also introduces the concept of Virtual Transport Network (VTN). A VTN is a virtual underlay network which consists of a set of dedicated or shared network resources allocated from the physical underlay network, and is associated with a logical network topology. VPN+ services can be delivered by mapping one or a group of overlay VPNs to the appropriate VTNs as the underlay, so as to provide the network characteristics required by the customers. In packet forwarding, traffic of different VPN+ services needs to be processed separately based on the network resources and the logical topology associated with the corresponding VTN. In the context of network slicing, VTN and NRP are considered as similar concepts, and NRP can be seen as an instantiation of VTN.

[I-D.dong-teas-nrp-scalability] describes the scalability considerations and the possible optimizations for providing a relatively large number of VTNs for VPN+ services. One approach to improve the data plane scalability of VTN is to introduce a dedicated VTN Resource Identifier (VTN Resource ID) in the data packet to identify the set of network resources allocated to a VTN, so that VTN-specific packet processing can be performed using that set of resources, which avoids the possible resource competition with services in other VTNs. This is called Resource Independent (RI) VTN. A VTN Resource ID represents a subset of the resources (e.g. bandwidth, buffer and queuing resources) allocated on a given set of links and nodes which constitute a logical network topology. The logical topology associated with a VTN could be defined using mechanisms such as Multi-Topology [RFC4915], [RFC5120] or Flex-Algo [I-D.ietf-lsr-flex-algo], etc.

This document proposes a mechanism to carry the VTN resource ID together with other VTN related information in a new Hop-by-Hop option called "VTN option" of IPv6 extension header [RFC8200] of IPv6 packet, so that on each network node along the packet forwarding path, the VTN option in the packet is parsed, and the obtained VTN Resource ID is used to instruct the network node to use the set of network resources allocated to the corresponding VTN to process and forward the packet. The procedure for processing the VTN option is also specified. This provides a scalable solution to support a relatively large number of VTNs in an IPv6 network.

1.1. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP14 RFC 2119 [RFC2119] RFC 8174 [RFC8174] when, and only when, they appear in all capitals, as shown here.

2. New IPv6 Extension Header Option for VTN

A new Hop-by-Hop option type "VTN" is defined to carry the VTN resource identifier and other VTN related information in an IPv6 packet. Its format is shown as below:

            Option   Option
             Type   Data Len
          +--------+--------+
          |BBCTTTTT| Length |
          +--------+--------+--------+--------+
  Option  |  Flags |        Reserved          |
   Data   +--------+--------+--------+--------+
          |           VTN Resource ID         |
          +--------+--------+--------+--------+
       Figure 1. The format of VTN Option

Option Type: 8-bit identifier of the type of option. The type of VTN option is to be assigned by IANA. The bits of the type field are defined as below:

Opt Data Len: 8-bit unsigned integer indicates the length of the option Data field of this option, in octets. The value of Opt Data Len of VTN option SHOULD be set to 8.

Flags: 8-bit flags field. The most significant bit is defined in this document.

           0 1 2 3 4 5 6 7
          +-+-+-+-+-+-+-+-+
          |S|U U U U U U U|
          +-+-+-+-+-+-+-+-+

Reserved: 3-octet field reserved for future use. They SHOULD be set to 0 on transmission and MUST be ignored on receipt.

VTN Resource ID: 4-octet identifier which uniquely identifies the set of network resources allocated to a VTN.

Note that, if a deployment found it useful, the four-octet VTN Resource ID field may be derived from the four-octet Single Network Slice Selection Assistance Information (S-NSSAI) defined in 3GPP [TS23501].

3. Procedures

As the VTN option needs to be processed by each node along the path for VTN-specific forwarding, it MUST be carried in IPv6 Hop-by-Hop options header.

3.1. Adding VTN Option to Packet

When an ingress node of an IPv6 domain receives a packet, according to the traffic classification or mapping policy, the packet is steered into one of the VTNs in the network, then the packet MUST be encapsulated in an outer IPv6 header, and the Resource ID of the VTN which the packet is mapped to MUST be carried in the VTN option of the Hop-by-Hop Options header associated with the outer IPv6 header.

3.2. VTN based Packet Forwarding

On receipt of a packet with the VTN option, each network node which can process the VTN option in fast path MUST use the VTN Resource ID to determine the set of local network resources allocated to the VTN for packet processing. The packet forwarding behavior is based on both the destination IP address and the VTN Resource ID. More specifically, the destination IP address is used to determine the next-hop and the outgoing interface, and VTN Resource ID is used to determine the set of network resources on the outgoing interface which are allocated to the VTN for processing and sending the packet. If the VTN Resource ID does not match with any of the VTN Resource ID provisioned on the outgoing interface, the S flag in the VTN option is used to determine whether the packet is dropped or forwarded using the default set of network resources of the outgoing interface. The Traffic Class field of the outer IPv6 header MAY be used to provide differentiated treatment for packets which belong to the same VTN. The egress node of the IPv6 domain MUST decapsulate the outer IPv6 header and the Hop-by-Hop Options header which includes the VTN option.

In the forwarding plane, there can be different approaches of partitioning the local network resources and allocating them to different VTNs. For example, on one physical interface, a subset of the forwarding plane resources (e.g. bandwidth and the associated buffer and queuing resources) can be allocated to a particular VTN and represented as a virtual sub-interface with reserved bandwidth resource. In packet forwarding, the IPv6 destination address of the received packet is used to identify the next-hop and the outgoing layer-3 interface, and the VTN Resource ID is used to further identify the virtual sub-interface on the outgoing interface which is associated with the VTN.

Network nodes which do not support the processing of Hop-by-Hop Options header SHOULD ignore the Hop-by-Hop options header and forward the packet only based on the destination IP address. Network nodes which support Hop-by-Hop Options header, but do not support the VTN option SHOULD ignore the VTN option and continue to forward the packet based on the destination IP address. The network node MAY process the rest of the Hop-by-Hop options in the Hop-by-Hop Options header.

4. Operational Considerations

As described in [RFC8200], network nodes may be configured to ignore the Hop-by-Hop Options header, drop packets containing a Hop-by-Hop Options header, or assign packets containing a Hop-by-Hop Options header to a slow processing path. [I-D.ietf-6man-hbh-processing] specifies the modified procedures for the processing of IPv6 Hop-by-Hop Options header. Operator needs to make sure that all the network nodes involved in a VTN can either process the Hop-by-Hop Options header in the fast path, or ignore the Hop-by-Hop Options header. Since a VTN is associated with a logical network topology, it is practical to ensure that all the network nodes involved in that logical topology support the processing of the Hop-by-Hop Options header and the VTN option. In other word, packets steered into a VTN MUST NOT be dropped due to the existence of the Hop-by-Hop Options header. It is RECOMMENDED to configure all the network nodes involved in a VTN to process the Hop-by-Hop Options header and the VTN option if there is a nob for this.

5. Considerations about Generalization

During the discussion of this document in the 6MAN WG, one of the suggestions received is to make the VTN option more generic in terms of semantics and encoding. This section gives some analysis about to what extent the semantics of VTN could be generalized, and how the generalization could be achieved with the proposed encoding.

Based on the VTN definition in [I-D.ietf-teas-enhanced-vpn], the concept of VTN could be extended as: a virtual network which is associated with a set of network-wide attributes and states maintained on each participating network node. The attributes associated with an VTN may include but not limited to: network resource attributes, network topology attributes, and network function attributes etc.

This shows the semantics of VTN can be quite generic. Although generalization is always something good to have, it would be important to understand and identify the boundary of generalization. In this document, It is anticipated that for one network attribute to be included in VTN, it needs to be a network-wide attribute rather than a node-specific attribute. Thus whether a network-wide view can be provided or not could be considered as one prerequisite of making one attribute part of VTN.

In terms of generic encoding, the format of the VTN option contains the Flags field and the Reserved field, which leave room for future extensions. The combination of the Flags field and the Reserved field can provide flexible encoding. For example, some of the Reserved field may be used to indicate the semantics of the ID, and based on the setting of the Flags field, additional forwarding behaviors may be introduced. That said, since the VTN option needs to be processed in the fast path, the capability of network devices need to be considered when new extensions to this VTN option are introduced.

6. IANA Considerations

This document requests IANA to assign a new option type from "Destination Options and Hop-by-Hop Options" registry.

   Value          Description       Reference
   --------------------------------------------
    TBA           VTN Option      this document

7. Security Considerations

The security considerations with IPv6 Hop-by-Hop Options header are described in [RFC8200], [RFC7045], [RFC9098] and [I-D.ietf-6man-hbh-processing]. This document introduces a new IPv6 Hop-by-Hop option which is either processed in the fast path or ignored by network nodes, thus it does not introduce additional security issues.

8. Contributors

   Zhibo Hu
   Email: huzhibo@huawei.com

   Lei Bao
   Email: baolei7@huawei.com

9. Acknowledgements

The authors would like to thank Juhua Xu, James Guichard, Joel Halpern, Tom Petch, Aijun Wang, Zhenqiang Li, Tom Herbert, Adrian Farrel and Eric Vyncke for their review and valuable comments.

10. References

10.1. Normative References

[I-D.ietf-6man-hbh-processing]
Hinden, R. M. and G. Fairhurst, "IPv6 Hop-by-Hop Options Processing Procedures", Work in Progress, Internet-Draft, draft-ietf-6man-hbh-processing-03, , <https://www.ietf.org/archive/id/draft-ietf-6man-hbh-processing-03.txt>.
[I-D.ietf-teas-enhanced-vpn]
Dong, J., Bryant, S., Li, Z., Miyasaka, T., and Y. Lee, "A Framework for Enhanced Virtual Private Network (VPN+)", Work in Progress, Internet-Draft, draft-ietf-teas-enhanced-vpn-11, , <https://www.ietf.org/archive/id/draft-ietf-teas-enhanced-vpn-11.txt>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8200]
Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, , <https://www.rfc-editor.org/info/rfc8200>.

10.2. Informative References

[I-D.dong-teas-nrp-scalability]
Dong, J., Li, Z., Gong, L., Yang, G., James Guichard, N., Mishra, G., Qin, F., Saad, T., and V. P. Beeram, "Scalability Considerations for Network Resource Partition", Work in Progress, Internet-Draft, draft-dong-teas-nrp-scalability-02, , <https://www.ietf.org/archive/id/draft-dong-teas-nrp-scalability-02.txt>.
[I-D.ietf-lsr-flex-algo]
Psenak, P., Hegde, S., Filsfils, C., Talaulikar, K., and A. Gulko, "IGP Flexible Algorithm", Work in Progress, Internet-Draft, draft-ietf-lsr-flex-algo-26, , <https://www.ietf.org/archive/id/draft-ietf-lsr-flex-algo-26.txt>.
[I-D.ietf-teas-ietf-network-slices]
Farrel, A., Drake, J., Rokui, R., Homma, S., Makhijani, K., Contreras, L. M., and J. Tantsura, "Framework for IETF Network Slices", Work in Progress, Internet-Draft, draft-ietf-teas-ietf-network-slices-15, , <https://www.ietf.org/archive/id/draft-ietf-teas-ietf-network-slices-15.txt>.
[RFC4915]
Psenak, P., Mirtorabi, S., Roy, A., Nguyen, L., and P. Pillay-Esnault, "Multi-Topology (MT) Routing in OSPF", RFC 4915, DOI 10.17487/RFC4915, , <https://www.rfc-editor.org/info/rfc4915>.
[RFC5120]
Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs)", RFC 5120, DOI 10.17487/RFC5120, , <https://www.rfc-editor.org/info/rfc5120>.
[RFC7045]
Carpenter, B. and S. Jiang, "Transmission and Processing of IPv6 Extension Headers", RFC 7045, DOI 10.17487/RFC7045, , <https://www.rfc-editor.org/info/rfc7045>.
[RFC9098]
Gont, F., Hilliard, N., Doering, G., Kumari, W., Huston, G., and W. Liu, "Operational Implications of IPv6 Packets with Extension Headers", RFC 9098, DOI 10.17487/RFC9098, , <https://www.rfc-editor.org/info/rfc9098>.
[RFC9099]
Vyncke, É., Chittimaneni, K., Kaeo, M., and E. Rey, "Operational Security Considerations for IPv6 Networks", RFC 9099, DOI 10.17487/RFC9099, , <https://www.rfc-editor.org/info/rfc9099>.
[TS23501]
"3GPP TS23.501", , <https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=3144>.

Authors' Addresses

Jie Dong
Huawei Technologies
Huawei Campus, No. 156 Beiqing Road
Beijing
100095
China
Zhenbin Li
Huawei Technologies
Huawei Campus, No. 156 Beiqing Road
Beijing
100095
China
Chongfeng Xie
China Telecom
China Telecom Beijing Information Science & Technology, Beiqijia
Beijing
102209
China
Chenhao Ma
China Telecom
China Telecom Beijing Information Science & Technology, Beiqijia
Beijing
102209
China
Gyan Mishra
Verizon Inc.