6lo P. Thubert, Ed. Internet-Draft Cisco Systems Updates: 6550, 8505, 9010 (if approved) 22 October 2021 Intended status: Standards Track Expires: 25 April 2022 IPv6 Neighbor Discovery Multicast Address Listener Registration draft-ietf-6lo-multicast-registration-01 Abstract This document updates RFC 8505 to enable a listener to subscribe to an IPv6 anycast or multicast address; the draft updates RFC 6550 (RPL) to add a new Non-Storing multicast mode and support for anycast addresses. This document also extends RFC 9010 to enable the 6LR to inject the anycast and multicast addresses in RPL. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 25 April 2022. Copyright Notice Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Thubert Expires 25 April 2022 [Page 1] Internet-Draft Multicast Address Registration October 2021 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1. Requirements Language . . . . . . . . . . . . . . . . . . 4 2.2. References . . . . . . . . . . . . . . . . . . . . . . . 4 2.3. Glossary . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Extending RFC 7400 . . . . . . . . . . . . . . . . . . . . . 8 5. Updating RFC 6550 . . . . . . . . . . . . . . . . . . . . . . 9 5.1. Updating MOP 3 . . . . . . . . . . . . . . . . . . . . . 9 5.2. New Non-Storing Multicast MOP . . . . . . . . . . . . . . 9 5.3. RPL Anycast Operation . . . . . . . . . . . . . . . . . . 10 5.4. New RPL Target Option Flags . . . . . . . . . . . . . . . 11 6. Updating RFC 8505 . . . . . . . . . . . . . . . . . . . . . . 11 6.1. New EARO flag . . . . . . . . . . . . . . . . . . . . . . 11 6.2. Registering Extensions . . . . . . . . . . . . . . . . . 12 7. Updating RFC 9010 . . . . . . . . . . . . . . . . . . . . . . 13 8. Deployment considerations . . . . . . . . . . . . . . . . . . 14 9. Security Considerations . . . . . . . . . . . . . . . . . . . 16 10. Backward Compatibility . . . . . . . . . . . . . . . . . . . 16 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16 11.1. New RTO flags . . . . . . . . . . . . . . . . . . . . . 17 11.2. New RPL Mode of Operation . . . . . . . . . . . . . . . 17 11.3. New EARO flags . . . . . . . . . . . . . . . . . . . . . 17 11.4. New 6LoWPAN Capability Bits . . . . . . . . . . . . . . 18 12. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 18 13. Normative References . . . . . . . . . . . . . . . . . . . . 18 14. Informative References . . . . . . . . . . . . . . . . . . . 20 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 22 1. Introduction The design of Low Power and Lossy Networks (LLNs) is generally focused on saving energy, which is the most constrained resource of all. Other design constraints, such as a limited memory capacity, duty cycling of the LLN devices and low-power lossy transmissions, derive from that primary concern. The radio (both transmitting or simply listening) is a major energy drain and the LLN protocols must be adapted to allow the nodes to remain sleeping with the radio turned off at most times. Thubert Expires 25 April 2022 [Page 2] Internet-Draft Multicast Address Registration October 2021 The "Routing Protocol for Low Power and Lossy Networks" [RFC6550] (RPL) to provide IPv6 [RFC8200] routing services within such constraints. To save signaling and routing state in constrained networks, the RPL routing is only performed along a Destination- Oriented Directed Acyclic Graph (DODAG) that is optimized to reach a Root node, as opposed to along the shortest path between 2 peers, whatever that would mean in each LLN. This trades the quality of peer-to-peer (P2P) paths for a vastly reduced amount of control traffic and routing state that would be required to operate an any-to-any shortest path protocol. Additionally, broken routes may be fixed lazily and on-demand, based on dataplane inconsistency discovery, which avoids wasting energy in the proactive repair of unused paths. Section 12 of [RFC6550] details the "Storing Mode of Operation with multicast support" with source-independent multicast routing in RPL. The classical "IPv6 Neighbor Discovery (IPv6 ND) Protocol" [RFC4861] [RFC4862] was defined for serial links and shared transit media such as Ethernet at a time when broadcast was cheap on those media while memory for neighbor cache was expensive. It was thus designed as a reactive protocol that relies on caching and multicast operations for the Address Discovery (aka Lookup) and Duplicate Address Detection (DAD) of IPv6 unicast addresses. Those multicast operations typically impact every node on-link when at most one is really targeted, which is a waste of energy, and imply that all nodes are awake to hear the request, which is inconsistent with power saving (sleeping) modes. The original 6LoWPAN ND, "Neighbor Discovery Optimizations for 6LoWPAN networks" [RFC6775], was introduced to avoid the excessive use of multicast messages and enable IPv6 ND for operations over energy-constrained nodes. [RFC6775] changes the classical IPv6 ND model to proactively establish the Neighbor Cache Entry (NCE) associated to the unicast address of a 6LoWPAN Node (6LN) in the a 6LoWPAN Router(s) (6LR) that serves it. To that effect, [RFC6775] defines a new Address Registration Option (ARO) that is placed in unicast Neighbor Solicitation (NS) and Neighbor Advertisement (NA) messages between the 6LN and the 6LR. "Registration Extensions for 6LoWPAN Neighbor Discovery" [RFC8505] updates [RFC6775] into a generic Address Registration mechanism that can be used to access services such as routing and ND proxy and introduces the Extended Address Registration Option (EARO) for that purpose. This provides a routing-agnostic interface for a host to request that the router injects a unicast IPv6 address in the local routing protocol and provide return reachability for that address. Thubert Expires 25 April 2022 [Page 3] Internet-Draft Multicast Address Registration October 2021 "Routing for RPL Leaves" [RFC9010] provides the router counterpart of the mechanism for a host that implements [RFC8505] to inject its unicast Unique Local Addresses (ULAs) and Global Unicast Addresses (GUAs) in RPL. But though RPL also provides multicast routing, 6LoWPAN ND supports only the registration of unicast addresses and there is no equivalent of [RFC9010] to specify the 6LR behavior upon the registration of one or more multicast address. The "Multicast Listener Discovery Version 2 (MLDv2) for IPv6" [RFC3810] enables the router to learn which node listens to which multicast address, but as the classical IPv6 ND protocol, MLD relies on multicasting Queries to all nodes, which is unfit for low power operations. As for IPv6 ND, it makes sense to let the 6LNs control when and how they maintain the state associated to their multicast addresses in the 6LR, e.g., during their own wake time. In the case of a constrained node that already implements [RFC8505] for unicast reachability, it makes sense to extend to that support to register the multicast addresses they listen to. This specification extends [RFC8505] and [RFC9010] to add the capability for the 6LN to register multicast addresses and for the 6LR to inject them in the RPL multicast support. 2. Terminology 2.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 2.2. References This document uses terms and concepts that are discussed in: * "Neighbor Discovery for IP version 6" [RFC4861] and "IPv6 Stateless address Autoconfiguration" [RFC4862], * Neighbor Discovery Optimization for Low-Power and Lossy Networks [RFC6775], as well as * "Registration Extensions for 6LoWPAN Neighbor Discovery" [RFC8505] and * "Using RPI Option Type, Routing Header for Source Routes, and IPv6-in-IPv6 Encapsulation in the RPL Data Plane" [RFC9008]. Thubert Expires 25 April 2022 [Page 4] Internet-Draft Multicast Address Registration October 2021 2.3. Glossary This document uses the following acronyms: 6BBR 6LoWPAN Backbone Router 6BBR 6LoWPAN Border Router 6LN 6LoWPAN Node 6LR 6LoWPAN Router 6CIO Capability Indication Option AMC Address Mapping Confirmation AMR Address Mapping Request ARO Address Registration Option DAC Duplicate Address Confirmation DAD Duplicate Address Detection DAR Duplicate Address Request EARO Extended Address Registration Option EDAC Extended Duplicate Address Confirmation EDAR Extended Duplicate Address Request DODAG Destination-Oriented Directed Acyclic Graph IR Ingress Replication LLN Low-Power and Lossy Network NA Neighbor Advertisement NCE Neighbor Cache Entry ND Neighbor Discovery NS Neighbor Solicitation ROVR Registration Ownership Verifier RTO RPL Target Option RA Router Advertisement RS Router Solicitation TID Transaction ID TIO Transit Information Option 3. Overview [RFC8505] is a pre-requisite to this specification. A node that implements this MUST also implement [RFC8505]. This specification does not introduce a new option; it modifies existing options and updates the associated behaviors to enable the Registration for Multicast Addresses as an extension to [RFC8505]. This specification also extends [RFC6550] and [RFC9010] in the case of a route-over multilink subnet based on the RPL routing protocol, to add multicast ingress replication in Non-Storing Mode and anycast support in both Storing and Non-Storing modes. A 6LR that implements the RPL extensions specified therein MUST also implement [RFC9010]. Thubert Expires 25 April 2022 [Page 5] Internet-Draft Multicast Address Registration October 2021 Figure 1 illustrates the classical situation of an LLN as a single IPv6 Subnet, with a 6LoWPAN Border Router (6LBR) that acts as Root for RPL operations and maintains a registry of the active registrations as an abstract data structure called an Address Registrar for 6LoWPAN ND. The LLN may be a hub-and-spoke access link such as (Low-Power) Wi-Fi [IEEE Std 802.11] and Bluetooth (Low Energy) [IEEE Std 802.15.1], or a Route-Over LLN such as the Wi-SUN mesh [Wi-SUN] that leverages 6LoWPAN [RFC4919][RFC6282] and RPL [RFC6550] over [IEEE Std 802.15.4]. | ----+-------+------------ | Wire side +------+ | 6LBR | |(Root)| +------+ o o o Wireless side o o o o o o o o o o o o o o o o LLN o +---+ o o o o o |6LR| o o o o o +---+ o o o o o o z o o oo o o +---+ o |6LN| +---+ Figure 1: Wireless Mesh A leaf acting as a 6LN registers its unicast addresses to a RPL router acting as a 6LR, using a unicast NS message with an EARO as specified in [RFC8505]. The registration state is periodically renewed by the Registering Node, before the lifetime indicated in the EARO expires. With this specification, the 6LNs can now subscribe to the multicast addresses they listen to, using a new M flag in the EARO to signal that the registration is for a multicast address. Multiple 6LN may subscribe to the same multicast address to the same 6LR. Note the use of the term "subscribe": using the EARO registration mechanism, a node registers the unicast addresses that it owns, but subscribes to the multicast addresses that it listens to. Thubert Expires 25 April 2022 [Page 6] Internet-Draft Multicast Address Registration October 2021 With this specification, the 6LNs can also resgister the anycast addresses they accept, using a new A flag in the EARO to signal that the registration is for an anycast address. As for multicast, multiple 6LN may register the same anycast address to the same 6LR. If the R flag is set in the registration of one or more 6LNs for the same address, the 6LR injects the anycast and multicast addresses in RPL, based on the longest registration lifetime across the active registrations for the address. In the RPL "Storing Mode of Operation with multicast support", the DAO messages for the multicast address percolate along the RPL preferred parent tree and mark a subtree that becomes the multicast tree for that multicast address, with 6LNs that subscribed to the address as the leaves. As prescribed in section 12 of [RFC6550], the 6LR forwards a multicast packet as an individual unicast MAC frame to each peer along the multicast tree, excepting to the node it received the packet from. In the new RPL "Non-Storing Mode of Operation with multicast support" that is introduced here, the DAO messages announce the multicast addresses as Targets though never as Transit. The multicast distribution is an ingress replication whereby the Root encapsulates the multicast packets to all the 6LRs that are transit for the multicast address, using the same source-routing header as for unicast targets attached to the respective 6LRs. Broadcasting is typically unreliable in LLNs (no ack) and forces a listener to remain awake, so it generally discouraged. The expectation is thus that in either mode, the 6LRs deliver the multicast packets as individual unicast MAC frames to each of the 6LNs that subscribed to the multicast address. With this specification, anycast addresses can be injected in RPL in both Storing and Non-Storing modes. In Storing Mode the RPL router accepts DAO from multiple children for the same anycast address, but only forwards a packet to one of the children. In Non-Storing Mode, the Root maintains the list of all the RPL nodes that announced the anycast address as Target, but forwards a given packet to only one of them. For backward compatibility, this specification allows to build a single DODAG signaled as MOP 1, that conveys anycast, unicast and multicast packets using the same source routing mechanism, more in Section 8. Thubert Expires 25 April 2022 [Page 7] Internet-Draft Multicast Address Registration October 2021 It is also possible to leverage this specification between the 6LN and the 6LR for the registration of unicast, anycast and multicast IPv6 addresses in networks that are not necessarily LLNs, and/or where the routing protocol between the 6LR and above is not necessarily RPL. In that case, the distribution of packets between the 6LR and the 6LNs may effectively rely on a broadcast or multicast support at the lower layer. For instance, it is possible to operate a RPL Instance in the new "Non-Storing Mode of Operation with multicast support" (while possibly signaling a MOP of 1) and use "Multicast Protocol for Low-Power and Lossy Networks (MPL)" [RFC7731] for the multicast operation. MPL floods the DODAG with the multicast messages independently of the RPL DODAG topologies. Two variations are possible: * In one possible variation, all the 6LNs set the R flag in the EARO for a multicast target, upon which the 6LRs send a unicast DAO message to the Root; the Root filters out the multicast messages for which there is no listener and only floods when there is. * In a simpler variation, the 6LNs do not set the R flag and the Root floods all the multicast packets over the whole DODAG. Using configuration, it is also possible to control the behavior of the 6LR to ignore the R flag and either always or never send the DAO message, and/or to control the Root and specify which groups it should flood or not flood. Note that if the configuration instructs the 6LR not to send the DAO, then MPL can really by used in conjunction with RPL Storing Mode as well. 4. Extending RFC 7400 This specification defines a new capability bit for use in the 6CIO as defined by "6LoWPAN-GHC: Generic Header Compression for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)" [RFC7400] and extended in [RFC8505] for use in IPv6 ND messages. The new "Registration for Multicast Address Supported" (M) flag indicates to the 6LN that the 6LR accepts multicast address registrations as specified in this document and will ensure that packets for the multicast Registered Address will be routed to the 6LNs that registered with the R flag set. Figure 2 illustrates the M flag in its suggested position (8, counting 0 to 15 in network order in the 16-bit array), to be confirmed by IANA. Thubert Expires 25 April 2022 [Page 8] Internet-Draft Multicast Address Registration October 2021 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length = 1 | Reserved |M|A|D|L|B|P|E|G| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: New Capability Bits in the 6CIO New Option Field: M 1-bit flag: "Registration for Multicast and Anycast Addresses Supported" 5. Updating RFC 6550 5.1. Updating MOP 3 RPL supports multicast operations in the "Storing Mode of Operation with multicast support" (MOP 3) which provides source-independent multicast routing in RPL, as prescribed in section 12 of [RFC6550]. MOP 3 is a storing Mode of Operation. This operation builds a multicast tree within the RPL DODAG for each multicast address. This specification provides additional details for the MOP 3 operation. The expectation in MOP 3 is that the unicast traffic also follows the Storing Mode of Operation. But this is rarely the case in LLN deployments of RPL where the "Non-Storing Mode of Operation" (MOP 1) is the norm. Though it is preferred to build separate RPL Instances, one in MOP 1 and one in MOP 3, this specification allows to hybrid the Storing Mode for multicast and Non-Storing Mode for unicast in the same RPL Instance, more in Section 8. 5.2. New Non-Storing Multicast MOP This specification adds a "Non-Storing Mode of Operation with multicast support" (MOP to be assigned by IANA) whereby the non- storing Mode DAO to the Root may contain multicast addresses in the RPL Target Option (RTO), whereas the Transit Information Option (TIO) can not. In that mode, the RPL Root performs an ingress replication (IR) operation on the multicast packets, meaning that it transmits one copy of each multicast packet to each 6LR that is a transit for the multicast target, using the same source routing header and encapsulation as it would for a unicast packet for a RPL Unaware Leaf (RUL) attached to that 6LR.. Thubert Expires 25 April 2022 [Page 9] Internet-Draft Multicast Address Registration October 2021 For the intermediate routers, the packet appears as any source routed unicast packet. The difference shows only at the 6LR, that terminates the source routed path and forwards the multicast packet to all 6LNs that registered for the muticast address. For a packet that is generated by the Root, this means that the Root builds a source routing header as shown in section 8.1.3 of [RFC9008], but for which the last and only the last address is multicast. For a packet that is not generated by the Root,the Root encapsulates the multicast packet as per section 8.2.4 of [RFC9008]. In that case, the outer header is purely unicast, and the encapsulated packet is purely multicast. For this new mode as well, this specification allows to enable the operation in a MOP 1 brown field, more in Section 8. 5.3. RPL Anycast Operation With multicast, the address has a recognizable format, and a multicast packet is to be delivered to all the active subscribers. In contrast with anycast, the format of the address is not distinguishable from that of unicast. In fact, an external destination (address or prefix) that may be injected from multiple border routers MUST be injected as anycast in RPL. For either multicast and anycast, there can be multiple registrations from multiple parties, each using a different value of the ROVR field that identifies the individual registration. The 6LR MUST maintain a registration state per value of the ROVR per multicast or anycast address, but inject the route into RPL only once for each address. Since the registrations are considered separate, the check on the TID that acts as registration sequence only applies to the registration with the same ROVR. The 6LRs that inject multicast and anycast routes into RPL may not be synchronized to advertise same value of the Path Sequence in the RPL TIO. It results that the value the Path Sequence is irrelevant when the target is anycast or multicast, and that it MUST be ignored. Like the 6LR, a RPL router in Storing Mode propagates the route to its parent(s) in DAO messages once and only once for each address, but it MUST retain a routing table entry for each of the children that advertised the address. Thubert Expires 25 April 2022 [Page 10] Internet-Draft Multicast Address Registration October 2021 When forwarding multicast packets down the DODAG, the RPL router copies all the children that advertised the address in their DAO messages. In contrast, when forwarding anycast packets down the DODAG, the RPL router MUST copy one and only one of the children that advertised the address in their DAO messages, and forward to one parent if there is no such child. 5.4. New RPL Target Option Flags [RFC6550] recognizes a multicast address by its format (as specified in section 2.7 of [RFC4291]) and applies the specified multicast operation if the address is recognized as multicast. This specification updates [RFC6550] to add the M and A flags to the RTO to indicate that the target address is to be processed as multicast or anycast, respectively. An RTO that has the M flag set is called a multicast RTO. An RTO that has the A flag set is called an anycast RTO. An RTO that has neither M nor A flag set is called a unicast RTO. The M and A flags are mutually exclusive and MUST NOT be both set. The suggested position for the A and M flags are 2 and 3 counting from 0 to 7 in network order as shown in Figure 3, based on figure 4 of [RFC9010] which defines the flags in position 0 and 1: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 0x05 | Option Length |F|X|A|M|ROVRsz | Prefix Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Target Prefix (Variable Length) | . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ... Registration Ownership Verifier (ROVR) ... | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: Format of the RPL Target Option 6. Updating RFC 8505 6.1. New EARO flag Section 4.1 of [RFC8505] defines the EARO as an extension to the ARO option defined in [RFC6775]. Thubert Expires 25 April 2022 [Page 11] Internet-Draft Multicast Address Registration October 2021 This specification adds a new M flag to the EARO flags field to signal that the Registered Address is a multicast address. When both the M and the R flags are set, the 6LR that conforms to this specification joins the multicast stream, e.g., by injecting the address in the RPL multicast support which is extended in this specification for Non-Storing Mode. This specification adds a new A flag to the EARO flags field to signal that the Registered Address is an anycast address. When both the A and the R flags are set, the 6LR that conforms to this specification injects the anycast address in the RPL anycast support that is introduced in this specification for both Storing and Non- Storing Modes. Figure 4 illustrates the A and M flags in their suggested positions (2 and 3, respectively, counting 0 to 7 in network order in the 8-bit array), to be confirmed by IANA. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Status | Opaque | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Rsv|A|M| I |R|T| TID | Registration Lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ... Registration Ownership Verifier ... | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: EARO Option Format New and updated Option Fields: Rsv 2-bit field: reserved, MUST be set to 0 and ignored by the receiver A 1-bit flag: "Registration for Anycast Address" M 1-bit flag: "Registration for Multicast Address" 6.2. Registering Extensions With [RFC8505]: * Only unicast addresses can be registered. * The 6LN must register all its ULA and GUA with a NS(EARO). Thubert Expires 25 April 2022 [Page 12] Internet-Draft Multicast Address Registration October 2021 * The 6LN may set the R flag in the EARO to obtain return reachability services by the 6LR, e.g., through ND proxy operations, or by injecting the route in a route-over subnet. * the 6LR maintains a registration state per Registered Address, including an NCE with the Link Layer Address (LLA) of the Registered Node (the 6LN here). This specification adds the following behavior: * Registration for multicast and anycast addresses is now supported. * The 6LN MUST also register all the IPv6 multicast addresses that it listens to and it MUST set the M flag in the EARO for those addresses. * The 6LN MAY set the R flag in the EARO to obtain the delivery of the multicast packets by the 6LR, e.g., by MLD proxy operations, or by injecting the address in a route-over subnet or in the Protocol Independent Multicast [RFC7761] protocol. * The 6LN MUST also register all the IPv6 anycast addresses that it supports and it MUST set the A flag in the EARO for those addresses. * The Registration Ownership Verifier (ROVR) in the EARO identifies uniquely a registration within the namespace of the Registered Address. The 6LR MUST maintain a registration state per tuple (IPv6 address, ROVR) for both anycast and multicast types of address, since multiple 6LNs may subscribe to the same address of these types. 7. Updating RFC 9010 With [RFC9010]: * The 6LR injects only unicast routes in RPL * upon a registration with the R flag set to 1 in the EARO, the 6LR injects the address in the RPL unicast support. * Upon receiving a packet directed to a unicast address for which it has an active registration, the 6LR delivers the packet as a unicast layer-2 frame to the LLA the nodes that registered the unicast address. This specification adds the following behavior: Thubert Expires 25 April 2022 [Page 13] Internet-Draft Multicast Address Registration October 2021 * Upon a registration with the R and the M flags set to 1 in the EARO, the 6LR injects the address in the RPL multicast support. * Upon receiving a packet directed to a multicast address for which it has at least one registration, the 6LR delivers a copy of the packet as a unicast layer-2 frame to the LLA of each of the nodes that registered to that multicast address. 8. Deployment considerations With this specification, a RPL DODAG forms a realm, and multiple RPL DODAGs may federated in a single RPL Instance administratively. This means that a multicast address that needs to span a RPL DODAG MUST use a scope of Realm-Local whereas a multicast address that needs to span a RPL Instance MUST use a scope of Admin-Local as discussed in section 3 of "IPv6 Multicast Address Scopes" [RFC7346]. "IPv6 Addressing of IPv4/IPv6 Translators" [RFC6052] enables to embed IPv4 addresses in IPv6 addresses. The Root of a DODAG may leverage that technique to translate IPv4 traffic in IPv6 and route along the RPL domain. When encapsulating an packet with an IPv4 multicast Destination Address, it MUST use form a multicast address and use the appropriate scope, Realm-Local or Admin-Local. "Unicast-Prefix-based IPv6 Multicast Addresses" [RFC3306] enables to form 2^32 multicast addresses from a single /64 prefix. If an IPv6 prefix is associated to an Instance or a RPL DODAG, this provides a namespace that can be used in any desired fashion. It is for instance possible for a standard defining organization to form its own registry and allocate 32-bit values from that namespace to network functions or device types. When used within a RPL deployment that is associated with a /64 prefix the IPv6 multicast addresses can be automatically derived from the prefix and the 32-bit value for either a Realm-Local or an Admin-Local multicast address as needed in the configuration. IN a "green field" deployment where all nodes support this specification, it is possible to deploy a single RPL Instance using a multicast MOP for unicast, multicast and anycast addresses. In a "brown field" where legacy devices that do not support this specification co-exist with upgraded devices, it is RECOMMENDED to deploy one RPL Instance in any Mode of Operation (typically MOP 1) for unicast that legacy nodes can join, and a separate RPL Instance dedicated to multicast and anycast operations using a multicast MOP. Thubert Expires 25 April 2022 [Page 14] Internet-Draft Multicast Address Registration October 2021 To deploy a Storing Mode multicast operation using MOP 3 in a RPL domain, it is required that there is enough density of RPL routers that support MOP 3 to build a DODAG that covers all the potential listeners and include the spanning multicast trees that are needed to distribute the multicast flows. This might not be the case when extending the capabilities of an existing network. In the case of the new Non-Storing multicast MOP, arguably the new support is only needed at the 6LRs that will accept multicast listeners. It is still required that each listener can reach at least one such 6LR, so the upgraded 6LRs must be deployed to cover all the 6LN that need multicast services. Using separate RPL Instances for in the one hand unicast traffic and in the other hand anycast and multicast traffic allows to use different objective function, one favoring the link quality up for unicast collection and one favoring downwards link quality for multicast distribution. But this might be impractical in some use cases where the signaling and the state to be installed in the devices are very constrained, the upgraded devices are too sparse, or the devices do not support more multiple instances. When using a single RPL Instance, MOP 3 expects the Storing Mode of Operation for both unicast and multicast, which is an issue in constrained networks that typically use MOP 1 for unicast. This specification allows a mixed mode that is signaled as MOP 1 in the DIO messages for backward compatibility, where limited multicast and/ or anycast is available, under the following conditions: * There MUST be enough density of 6LRs that support the mixed mode to cover the all the 6LNs that require multicast or anycast services. In Storing Mode, there MUST be enough density or 6LR that support the mixed mode to also form a DODAG to the Root. * The RPL routers that support the mixed mode and are configured to operate in in accordance with the desired operation in the network. * The MOP signaled in the RPL DODAG Information Object (DIO) messages is MOP 1 to enable the legacy nodes to operate as leaves. * The support of multicast and/or anycast in the RPL Instance SHOULD be signaled by the 6LRs to the 6LN using a 6CIO, see Section 4. Thubert Expires 25 April 2022 [Page 15] Internet-Draft Multicast Address Registration October 2021 * Alternatively, the support of multicast in the RPL domain can be globally known by other means such as configuration or external information such as support of a version of an industry standard that mandates it. In that case, all the routers MUST support the mixed mode. 9. Security Considerations This specification extends [RFC8505], and the security section of that document also applies to this document. In particular, the link layer SHOULD be sufficiently protected to prevent rogue access. 10. Backward Compatibility A legacy 6LN will not register multicast addresses and the service will be the same when the network is upgraded. A legacy 6LR will not set the M flag in the 6CIO and an upgraded 6LN will not register multicast addresses. As detailed in Section 8, it is possible to add multicast on an existing MOP 1 deployment, The combination of a multicast address and the M flag set to 0 in an RTO in a MOP 3 RPL Instance is understood by the receiver that supports this specification (the parent) as an indication that the sender (child) does not support this specification, but the RTO is accepted and processed as if the M flag was set for backward compatibility. When the DODAG is operated in MOP 3, a legacy node will not set the M flag and still expect multicast service as specified in section 12 of [RFC6550]. In MOP 3 an RTO that is received with a target that is multicast and the M bit set to 0 MUST be considered as multicast and MUST be processed as if the M flag is set. 11. IANA Considerations Note to RFC Editor, to be removed: please replace "This RFC" throughout this document by the RFC number for this specification once it is allocated. Also, the I Field is defined in RFC 9010 but we failed to insert it in the subregistry and the flags appear as unspecified though they are. IANA is requested to make changes under the "Internet Control Message Protocol version 6 (ICMPv6) Parameters" [IANA.ICMP] and the "Routing Protocol for Low Power and Lossy Networks (RPL)" [IANA.RPL] registries, as follows: Thubert Expires 25 April 2022 [Page 16] Internet-Draft Multicast Address Registration October 2021 11.1. New RTO flags IANA is requested to make additions to the "RPL Target Option Flags" [IANA.RPL.RTO.FLG] subregistry of the "Routing Protocol for Low Power and Lossy Networks (RPL)" registry as indicated in Table 1: +---------------+---------------------------------------+-----------+ | Bit Number | Meaning | Reference | +---------------+---------------------------------------+-----------+ | 2 (suggested) | A flag: Target is an Anycast Address | This RFC | +---------------+---------------------------------------+-----------+ | 3 (suggested) | M flag: Target is a Multicast | This RFC | | | Address | | +---------------+---------------------------------------+-----------+ Table 1: New RTO flags 11.2. New RPL Mode of Operation IANA is requested to make an addition to the "Mode of Operation" [IANA.RPL.MOP] subregistry of the "Routing Protocol for Low Power and Lossy Networks (RPL)" registry as indicated in Table 2: +---------------+-------------------------------+-----------+ | Value | Description | Reference | +---------------+-------------------------------+-----------+ | 5 (suggested) | Non-Storing Mode of Operation | This RFC | | | with multicast support | | +---------------+-------------------------------+-----------+ Table 2: New RPL Mode of Operation 11.3. New EARO flags IANA is requested to make additions to the "Address Registration Option Flags" [IANA.ICMP.ARO.FLG] of the "Internet Control Message Protocol version 6 (ICMPv6) Parameters" registry as indicated in Table 3: Thubert Expires 25 April 2022 [Page 17] Internet-Draft Multicast Address Registration October 2021 +---------------+-----------------------+-----------+ | ARO flag | Meaning | Reference | +---------------+-----------------------+-----------+ | 2 (suggested) | A flag: Registration | This RFC | | | for Anycast Address | | +---------------+-----------------------+-----------+ | 3 (suggested) | M flag: Registration | This RFC | | | for Multicast Address | | +---------------+-----------------------+-----------+ | 4 and 5 | "I" Field | RFC 8505 | +---------------+-----------------------+-----------+ Table 3: New ARO flags 11.4. New 6LoWPAN Capability Bits IANA is requested to make an addition to the "6LoWPAN Capability Bits" [IANA.ICMP.6CIO] subregistry subregistry of the "Internet Control Message Protocol version 6 (ICMPv6) Parameters" registry as indicated in Table 4: +----------------+------------------------------------+-----------+ | Capability Bit | Meaning | Reference | +----------------+------------------------------------+-----------+ | 8 (suggested) | M flag: Registration for Multicast | This RFC | | | and Anycast Addresses Supported | | +----------------+------------------------------------+-----------+ Table 4: New 6LoWPAN Capability Bits 12. Acknowledgments 13. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC3306] Haberman, B. and D. Thaler, "Unicast-Prefix-based IPv6 Multicast Addresses", RFC 3306, DOI 10.17487/RFC3306, August 2002, . [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006, . Thubert Expires 25 April 2022 [Page 18] Internet-Draft Multicast Address Registration October 2021 [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, DOI 10.17487/RFC4861, September 2007, . [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, DOI 10.17487/RFC4862, September 2007, . [RFC6550] Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J., Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur, JP., and R. Alexander, "RPL: IPv6 Routing Protocol for Low-Power and Lossy Networks", RFC 6550, DOI 10.17487/RFC6550, March 2012, . [RFC6775] Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C. Bormann, "Neighbor Discovery Optimization for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)", RFC 6775, DOI 10.17487/RFC6775, November 2012, . [RFC7346] Droms, R., "IPv6 Multicast Address Scopes", RFC 7346, DOI 10.17487/RFC7346, August 2014, . [RFC7400] Bormann, C., "6LoWPAN-GHC: Generic Header Compression for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)", RFC 7400, DOI 10.17487/RFC7400, November 2014, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, July 2017, . [RFC8505] Thubert, P., Ed., Nordmark, E., Chakrabarti, S., and C. Perkins, "Registration Extensions for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery", RFC 8505, DOI 10.17487/RFC8505, November 2018, . Thubert Expires 25 April 2022 [Page 19] Internet-Draft Multicast Address Registration October 2021 [RFC9010] Thubert, P., Ed. and M. Richardson, "Routing for RPL (Routing Protocol for Low-Power and Lossy Networks) Leaves", RFC 9010, DOI 10.17487/RFC9010, April 2021, . [IANA.ICMP] IANA, "IANA Registry for ICMPv6", IANA, https://www.iana.org/assignments/icmpv6-parameters/ icmpv6-parameters.xhtml. [IANA.ICMP.ARO.FLG] IANA, "IANA Sub-Registry for the ARO Flags", IANA, https://www.iana.org/assignments/icmpv6-parameters/ icmpv6-parameters.xhtml#icmpv6-adress-registration-option- flags. [IANA.ICMP.6CIO] IANA, "IANA Sub-Registry for the 6LoWPAN Capability Bits", IANA, https://www.iana.org/assignments/icmpv6-parameters/ icmpv6-parameters.xhtml#sixlowpan-capability-bits. [IANA.RPL] IANA, "IANA Registry for the RPL", IANA, https://www.iana.org/assignments/rpl/rpl.xhtml. [IANA.RPL.RTO.FLG] IANA, "IANA Sub-Registry for the RTO Flags", IANA, https://www.iana.org/assignments/rpl/rpl.xhtml#rpl-target- option-flags. [IANA.RPL.MOP] IANA, "IANA Sub-Registry for the RPL Mode of Operation", IANA, https://www.iana.org/assignments/rpl/rpl.xhtml#mop. 14. Informative References [RFC3810] Vida, R., Ed. and L. Costa, Ed., "Multicast Listener Discovery Version 2 (MLDv2) for IPv6", RFC 3810, DOI 10.17487/RFC3810, June 2004, . [RFC4919] Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals", RFC 4919, DOI 10.17487/RFC4919, August 2007, . Thubert Expires 25 April 2022 [Page 20] Internet-Draft Multicast Address Registration October 2021 [RFC6282] Hui, J., Ed. and P. Thubert, "Compression Format for IPv6 Datagrams over IEEE 802.15.4-Based Networks", RFC 6282, DOI 10.17487/RFC6282, September 2011, . [RFC7731] Hui, J. and R. Kelsey, "Multicast Protocol for Low-Power and Lossy Networks (MPL)", RFC 7731, DOI 10.17487/RFC7731, February 2016, . [RFC7761] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I., Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol Specification (Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March 2016, . [RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X. Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052, DOI 10.17487/RFC6052, October 2010, . [RFC9008] Robles, M.I., Richardson, M., and P. Thubert, "Using RPI Option Type, Routing Header for Source Routes, and IPv6- in-IPv6 Encapsulation in the RPL Data Plane", RFC 9008, DOI 10.17487/RFC9008, April 2021, . [Wi-SUN] Heile, B., (Remy), B. L., Zhang, M., and C. E. Perkins, "Wi-SUN FAN Overview", Work in Progress, Internet-Draft, draft-heile-lpwan-wisun-overview-00, 3 July 2017, . [IEEE Std 802.15.4] IEEE standard for Information Technology, "IEEE Std 802.15.4, Part. 15.4: Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks". [IEEE Std 802.11] IEEE standard for Information Technology, "IEEE Standard 802.11 - IEEE Standard for Information Technology - Telecommunications and information exchange between systems Local and metropolitan area networks - Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications.", . Thubert Expires 25 April 2022 [Page 21] Internet-Draft Multicast Address Registration October 2021 [IEEE Std 802.15.1] IEEE standard for Information Technology, "IEEE Standard for Information Technology - Telecommunications and Information Exchange Between Systems - Local and Metropolitan Area Networks - Specific Requirements. - Part 15.1: Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Wireless Personal Area Networks (WPANs)". Author's Address Pascal Thubert (editor) Cisco Systems, Inc Building D 45 Allee des Ormes - BP1200 06254 Mougins - Sophia Antipolis France Phone: +33 497 23 26 34 Email: pthubert@cisco.com Thubert Expires 25 April 2022 [Page 22]