Network Working Group L. Huang
Internet-Draft A. Clemm
Intended status: Informational Cisco Systems
Expires: March 4, 2013 August 31, 2012
YANG Data Model for Access Control List Configuration
draft-huang-netmod-acl-00.txt
Abstract
This document defines a YANG data model for the configuration of
Access Control Lists (ACLs) on a device.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 4, 2013.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
Huang & Clemm Expires March 4, 2013 [Page 1]
Internet-Draft yang-acl August 2012
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Huang & Clemm Expires March 4, 2013 [Page 2]
Internet-Draft yang-acl August 2012
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Definitions and Acronyms . . . . . . . . . . . . . . . . . . . 4
3. The Design of ACL Data Model . . . . . . . . . . . . . . . . . 5
4. acl Module . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1. Features . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2. Types . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3. Groupings . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3.1. PORT-GROUP grouping . . . . . . . . . . . . . . . . . 11
4.3.2. MAC-SOURCE-NETWORK grouping . . . . . . . . . . . . . 11
4.3.3. MAC-DESTINATION-NETWORK grouping . . . . . . . . . . . 12
4.3.4. IP-ADDRESS-AND-MASK grouping . . . . . . . . . . . . . 13
4.3.5. IP-SOURCE-NETWORK grouping . . . . . . . . . . . . . . 13
4.3.6. IP-DESTINATION-NETWORK grouping . . . . . . . . . . . 14
4.4. Containers . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.1. acls Container . . . . . . . . . . . . . . . . . . . . 15
4.4.2. port-obj-grp Container . . . . . . . . . . . . . . . . 15
4.4.3. timerange-obj-grp Container . . . . . . . . . . . . . 16
4.4.4. ip-address-obj-grp Container . . . . . . . . . . . . . 16
5. acl-ip module . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1. Groupings . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1.1. ACTIONS Grouping . . . . . . . . . . . . . . . . . . . 18
5.1.2. SRC-PORT-GROUP grouping . . . . . . . . . . . . . . . 18
5.1.3. DES-PORT-GROUP grouping . . . . . . . . . . . . . . . 19
5.1.4. IP-ACE-FILTERS Grouping . . . . . . . . . . . . . . . 19
5.1.5. IPV4-ACE-GROUP Grouping . . . . . . . . . . . . . . . 21
5.1.6. IPV6-ACE-GROUP Grouping . . . . . . . . . . . . . . . 23
5.2. augment . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.2.1. global-fragments leaf . . . . . . . . . . . . . . . . 25
6. acl-mac module . . . . . . . . . . . . . . . . . . . . . . . . 28
6.1. MAC-ACE-GROUP group . . . . . . . . . . . . . . . . . . . 28
6.1.1. mac-ace list . . . . . . . . . . . . . . . . . . . . . 29
6.2. augment . . . . . . . . . . . . . . . . . . . . . . . . . 29
7. acl-arp module . . . . . . . . . . . . . . . . . . . . . . . . 29
7.1. ARP-ACE-GROUP group . . . . . . . . . . . . . . . . . . . 30
7.2. arp-ace list . . . . . . . . . . . . . . . . . . . . . . . 30
7.3. augment . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. Data Model Structure . . . . . . . . . . . . . . . . . . . . . 31
9. ACL YANG Module . . . . . . . . . . . . . . . . . . . . . . . 37
10. ACL-IP YANG Module . . . . . . . . . . . . . . . . . . . . . . 54
11. ACL-MAC Configuration YANG Module . . . . . . . . . . . . . . 67
12. ACL-ARP Configuration YANG Module . . . . . . . . . . . . . . 72
13. COMMON-TYPES YANG Module . . . . . . . . . . . . . . . . . . . 75
14. Security Considerations . . . . . . . . . . . . . . . . . . . 83
15. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 83
16. Normative References . . . . . . . . . . . . . . . . . . . . . 83
Huang & Clemm Expires March 4, 2013 [Page 3]
Internet-Draft yang-acl August 2012
1. Introduction
This document defines a YANG [RFC6020] data model for the
configuration of Access Control Lists (ACLs).
An ACL is an ordered set of rules that is used to filter traffic on a
networking device, i.e. to define "firewall rules". Each rule is
represented by an Access Control Entry (ACE). An ACE consists of two
parts:
Filters with a set of matching criteria that a packet must satisfy
for the rule to be applied.
Actions that specifies what to do with the packet when the matching
criteria is met, for example, to drop the packet.
There are different types of ACL: MAC ACL, IP ACL, and ARP ACL.
MAC ACLs - MAC ACLs are used to filter traffic using the information
in the Layer 2 header of each packet. MAC ACLs are by default only
applied to non-IP traffic; however, Layer 2 interfaces can be
configured to apply MAC ACLs to all traffic.
IP ACLs: IP ACLs are ordered sets of rules that can use to filter
traffic based on IP information in the Layer 3 header of packets.
The device applies IP ACLs only to IP traffic. IP ACL can be IPv4 or
IPv6.
ARP ACLs - The device applies ARP ACLs to IP traffic.
Not every device implements every type of ACL. In addition, device
implementations may vary greatly in terms of the filter constructs
that they support. Therefore, acl YANG Module makes extensive use of
the "feature" construct which allows implementations to support those
ACL configuration features that lie within their capabilities.
The applying of ACL to device configuration to interfaces and other
components is out of the scope of this model.
2. Definitions and Acronyms
ACE: Access Control Entry
ACL: Access Control List
AFI: Address Field Identifier
ARP: Address Resolution Protocol
Huang & Clemm Expires March 4, 2013 [Page 4]
Internet-Draft yang-acl August 2012
CoS: Class of Service
DSCP: Differentiated Services Code Point
ICMP: Internet Control Message Protocol
IGMP: Internet Group Management Protocol
IP: Internet Protocol
IPv4: Internet Protocol version 4
IPv6: Internet Protocol version 6
MAC: Media Access Control
QoS: Quality of Service
TCP: Transmission Control Protocol
ToS: Type of Service
TTL: Time To Live
UDP: User Datagram Protocol
VLAN: Virtual Local Area Network
VRF: Virtual Routing and Forwarding
3. The Design of ACL Data Model
The ACL data model consists of five YANG modules. The first module,
"acl", defines generic ACL aspects which are common to all ACLs
regardless of their type, as well as a set of auxiliary definitions.
In effect, the module can be viewed as providing a generic ACL
"superclass".
Three other modules, "acl-ip", "acl-mac", and "acl-arp" , augment the
"acl" module with definitions that are specific to different types of
ACLs, specifically, ACLs for IP, MAC, and ARP, respectively. These
specifics are for the largest part reflected in the Access Control
Entries, that is, the rules which specify the filter criteria that a
packet must meet for the rule to be applied, and the actions that are
to be taken in case the filter matches. Keeping the modules separate
provides for a more modular data model than would be the case if all
types were combined into a single monolithic module.
Huang & Clemm Expires March 4, 2013 [Page 5]
Internet-Draft yang-acl August 2012
Finally, module "common-types" defines types that are used in the ACL
data model but are not really specific to ACLs. These definitions
could potentially be of interest to other models as well; keeping
them in a separate module allows to import these definitions
independent of the support for ACLs.
The data hierarchy that is defined by the acl module is depicted in
the following Figure 1, where brackets enclose list keys, "rw" means
configuration, "ro" operational state data, and "?" means optional
node. Parentheses enclose choice and case nodes. The structure is a
collapsed structure and does not depict all definitions; it is
intended to illustrate the overall structure. A fully expanded
structure can be found in Data Model Structure Section Section 8.
module: acl
+--rw acls
+--rw acl [name]
| +--rw name
| +--rw acl-type
| +--rw enable-capture-global?
| +--rw capture-session-id-global?
| +--rw (enable-match-counter-choices)?
| +--ro match?
|
|
+--rw port-obj-grp
| +--rw port-group [name]
| +--rw name
| +--rw groups
+--rw timerange-obj-grp
| +--rw timerange-group [name]
| +--rw name
| +--rw time-ranges
+--rw ip-address-obj-grp
rpcs:
+--x reset-match-counter
+--ro input
+--ro name
+--ro sequence-num?
Figure 1
Data nodes in the acl module are contained under a single container
node, acls. This node contains a list, "acl". Each ACL is
represented by an list element in that list, which is identified by a
name that serves as key to the list. Interfaces (which are not part
of the model) to which an ACL is applied can then refer to the ACL
using that name. Each acl list element has furthermore a type, as
Huang & Clemm Expires March 4, 2013 [Page 6]
Internet-Draft yang-acl August 2012
indicated through "acl-type". The acl-type determines which types of
ACEs can be can be contained in an ACL. The ACE definitions
themselves are provided by the acl-ip, acl-mac, and acl-arp modules,
which augment the acl definition in the acl module accordingly. The
subsequent data nodes in the acl list allow to configure whether
packets that match an ACL should be captured for further analysis.
Finally, the list contains an object that maintains a counter of the
number of ACL matches. the rpc "reset-match-counter" can be used to
reset that counter.
port-obj-grp, timerange-obj-grp, ip-address-obj-grp are auxiliary
objects used to define groupings of ports and of IP ranges as well as
schedule information, respectively. They are in effect convenience
objects which allow ACEs to refer to groupings and schedules by name,
rather than needing to respecify them in each ACE where they apply.
The following figure depicts how different types of ACEs are inserted
into that structure. As indicated earlier, the corresponding
definitions are provided in separate modules that augment the acl
module. In the data structure, the augmenting module is indicate by
the prefix of the corresponding data nodes: acl-ip, acl-mac, and acl-
arp, respectively. ACEs for IPv4 and for IPv6 are both defined in
the same module, acl-ip. While it would have been possible to define
each in its own separate module, it was a design decision to combine
them, as they share enough commonality that a separation would have
resulted in a considerable amount of definition redundancy.
The figure does not depict objects not pertinent to that structure,
such as the reusable objects, port-obj-grp, timerange-obj-grp, and
ip-address-obj-grp, or general objects contained in acl list
elements, such as name and enable-capture-global.
module: acl
+--rw acls
+--rw acl [name]
| +--rw acl-ip:afi
| +--rw acl-ip:ipv6-aces
| | +--rw acl-ip:ipv6-ace [sequence-num]
| | +--rw acl-ip:sequence-num
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-ip:remark
| | +--:(filter)
| | | +--rw acl-ip:filter
| | | +-- filter parameters
| | | +--rw acl-ip:actions
| | | +-- action parameters
| | +-- ro acl-ip:statistics
Huang & Clemm Expires March 4, 2013 [Page 7]
Internet-Draft yang-acl August 2012
module: acl
+--rw acls
+--rw acl [name]
| +--rw acl-ip:afi
| +--rw acl-ip:ipv4-aces
| | +--rw acl-ip:ipv4-ace [sequence-num]
| | +--rw acl-ip:sequence-num
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-ip:remark
| | +--:(filter)
| | | +--rw acl-ip:filters
| | | +-- filter parameters
| | | +--rw acl-ip:actions
| | | +-- action parameters
| | +-- ro acl-ip:match
module: acl
+--rw acls
+--rw acl [name]
| +--rw acl-mac:mac-aces
| | +--rw acl-mac:mac-ace [sequence-num]
| | +--rw acl-mac:sequence-num
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-mac:remark
| | +--:(filter)
| | | +--rw acl-mac:filters
| | | +-- filter parameters
| | | +--rw acl-mac:actions
| | | +-- action parameters
| | +-- ro acl-mac:match
module: acl
+--rw acls
+--rw acl [name]
| +--rw acl-arp:arp-aces
| | +--rw acl-arp:arp-ace [sequence-num]
| | +--rw acl-arp:sequence-num
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-arp:remark
| | +--:(filter)
| | | +--rw acl-arp:filters
| | | +-- filter parameters
| | | +--rw acl-arp:actions
| | | +-- action parameters
Huang & Clemm Expires March 4, 2013 [Page 8]
Internet-Draft yang-acl August 2012
| | +-- ro acl-arp:match
Figure 2
As is evident from Figure 2, the same generic design pattern is
reflected in every ACL type. Each ACL contains a list of ACEs,
identified by a numeric identifier by which ACEs in the list are
ordered. (Numeric identifiers do not have to be sequential, but are
unique.) Each ACE consists either of a remark or an actual access
control rule, i.e. a "filter". Remarks are in effect comment lines
inside an ACL that are intended for human or administrator
consumption. They are included in the YANG module to maintain
consistency with CLI. Access control rules, on the other hand,
consist of a left hand side ("filters") that specifies a set of
matching criteria and right hand side ("actions") that specifies the
action to take when matching criteria are met. An overview of the
full list of filter and parameters is given in Section 8.
Since the design pattern for each ACL type is the same, an
alternative design to the YANG modules would have been to extend the
acl module to include the data nodes up to the level depicted in
Figure 2, as the real distinction occurs in the filter and action
parameters that occur below it. In that case, however, the
corresponding data nodes would have had to contend with more complex
conditions. The modules defined here aim at keeping compleixty of
definitions within the modules as low as possible, at the price of
not needing to repeat a few data nodes that provide the overall top
level structure.
4. acl Module
acl module is a top container module for all acls. It contains a
list of named acl. acl-ip, acl-map and acl-arp augment the acl list
in acls container. In addition to the acls container, it also
defined features, reusable types and reusable grouping.
4.1. Features
When it comes to ACL implementation, there is a wide range of
capabilities across devices. For example, not every device
implements every type of ACL. Some devices may support time-based
ACLs that are only in effect during specified times, others may not.
In order to accommodate this wide range of capabilities, this data
model makes extensive use of the "feature" construct. The defined
features allow implementations to declare which capabilities they
support, and only support the corresponding portions of the data
model.
Huang & Clemm Expires March 4, 2013 [Page 9]
Internet-Draft yang-acl August 2012
4.2. Types
The definition of ACLs requires a number of new data types. The
following data types are introduced in this data model. Table 1 has
the data types that is unique to acl model. Table 2 has the data
types that will reused in other models defined in common-types
module. For details of each type, see each typedef descriptions and
reference in the model.
+----------------------+------------------------------+
| YANG type | base type |
+---------------------+-------------------------------+
| Comparator | enumeration |
| ACL-Action | enumeration |
| IP-Network-Kind | enumeration |
| Mac-Network-Kind | enumeration |
| Sequence-Number | uint32 |
| Remark | string |
| Acl-Type-Ref | identityref |
| Acl-Ref | leafref |
| Port-Group-Ref | leafref |
| IP-Address-Group-Ref | leafref |
| Time-Range-Ref | leafref |
+--------------------- +------------------------------+
Table 1
+----------------------+------------------------------+
| YANG type | base type |
+---------------------+-------------------------------+
| Cos | uint8 |
| Tos | uint8 |
| Precedence | uint8 |
| TCP-Flag-Type | enumeration |
| Ether-Type | string |
| IP-Protocol | uint8 |
| IGMP-Code | uint8 |
| ICMP-Type | uint32 |
| ICMP-Code | uint32 |
| Vlan-Identifier | uint16 |
| Time-to-Live | uint32 |
+--------------------- +------------------------------+
Table 2
Huang & Clemm Expires March 4, 2013 [Page 10]
Internet-Draft yang-acl August 2012
4.3. Groupings
The data model defines a number of groupings, consisting of sets of
objects that are used in multiple places. In order to keep the
overview of the data model concise, those groupings are introduced in
the following subsections and subsequently referred to by name,
rather than expanding groupings in the data model.
4.3.1. PORT-GROUP grouping
PORT-GROUP
+--rw (port-number-or-range)?
+--:(port-number-range)
| +--rw port-lower? inet:port-number
| +--rw port-upper? inet:port-number
+--:(port-number)
+--rw comparator Comparator
+--rw port? inet:port-number
PORT-GROUP has two ways to express a group of ports:
Using port-upper and port-lower couple to specify a port range.
The value of port-lower must be less or equal to port-upper
Using comparator and port couple to specify the port(s). For
example:
20
21
eq
80
See Comparator typedef in model appendix for possible comparator
values.
4.3.2. MAC-SOURCE-NETWORK grouping
MAC-SOURCE-NETWORK
+--rw acl-mac:mac-source-kind? MAC-Network-Kind
+--rw (source-network)?
+--:(address)
| +--rw acl-mac:source-address yang:mac-address
| +--rw acl-mac:source-address-mask yang:mac-address
+--:(host)
+--rw acl-mac:source-host-name inet:host
Huang & Clemm Expires March 4, 2013 [Page 11]
Internet-Draft yang-acl August 2012
MAC-SOURCE-ADDRESS is a reusable grouping. It uses four leaves: mac-
source-kind, source-address, source-address-mask and source-host-name
to express the three kinds network.
any network: use mac-source-kind value any to express any network.
any
single host network.
host
my-host
host address with a mask.
mac
0180.c200.000
0000.0000.0000
4.3.3. MAC-DESTINATION-NETWORK grouping
MAC-DESTINATION-NETWORK
+--rw acl-mac:mac-destination-kind? MAC-Network-Kind
+--rw (dest-network)?
+--:(address)
| +--rw acl-mac:dest-address yang:mac-address
| +--rw acl-mac:dest-address-mask yang:mac-address
+--:(host)
+--rw acl-mac:dest-host-name inet:host
MAC-DESTINATION-ADDRESS is a reusable grouping similar to MAC-SOURCE-
ADDRESS. The reason to have both MAC-SOURCE-ADDRESS and MAC-
DESTINATION-ADDRESS grouping is to allow source-address and
destination-address leaves appear in the same container. For
example:
mac
0180.c200.000
0000.0000.0000
any
Huang & Clemm Expires March 4, 2013 [Page 12]
Internet-Draft yang-acl August 2012
4.3.4. IP-ADDRESS-AND-MASK grouping
IP-ADDRESS-AND-MASK
+--rw ip-address-kind IP-Network-Kind
+--rw (mask-or-host)?
+--:(mask)
| +--rw ip-address inet:ip-address
| +--rw ip-mask? inet:ip-prefix
+--:(host)
| +--rw (ip-host-address)? inet:host
IP-ADDRESS-AND-MASK is a reusable grouping. It has four leaves: ip-
address-kind, ip-source-address, ip-source-mask and ip-host-address
to express the three kinds network.
any network.
any
single host network.
host
my-host
host address with a mask.
mac
192.168.1.0
255.255.255.0
4.3.5. IP-SOURCE-NETWORK grouping
IP-SOURCE-NETWORK
+--rw ip-source-kind IP-Network-Kind
+--rw (source-address-host-group)?
+--:(address)
| +--rw ip-source-address inet:ip-address
| +--rw ip-source-mask? inet:ip-prefix
+--:(host-name)
| +--rw (ip-source-host-address)? inet:host
+--:(group)
+--rw ip-source-group? IP-Address-Group-Ref
IP-SOURCE-NETWORK is a reusable grouping. It has four leaves: ip-
address-kind, ip-source-address, ip-source-mask, ip-host-address, and
ip-source-group to express the four kinds network. The following are
valid instances:
Huang & Clemm Expires March 4, 2013 [Page 13]
Internet-Draft yang-acl August 2012
ip-source-address is an ip address:
ip
192.168.1.0
255.255.255.0
ip-source-address is 'any':
any
ip-source-address is an 'host' with host-name:
host
switch1
ip-source-address is an 'host' with host-name:
host
192.168.1.2
ip-source-address is an 'group':
group
Email-Server-IPV4
4.3.6. IP-DESTINATION-NETWORK grouping
IP-DESTINATION-NETWORK
+--rw ip-dest-kind IP-Network-Kind
+--rw (dest-address-host-group)?
+--:(address)
| +--rw ip-dest-address inet:ip-address
| +--rw ip-dest-mask? inet:ip-prefix
+--:(host)
| +--rw (ip-dest-host-address)? inet:ip-host
+--:(group)
+--rw ip-dest-group? IP-Address-Group-Ref
IP-DESTINATION-ADDRESS is a reusable grouping. Its structure is
similar to IP-SOURCE-NETWORK.The reason to have IP-SOURCE-NETWORK and
IP-DESTINATION-NETWORK grouping is to allow ip-source-address and ip-
destination-address leaves appear in the same container. For
example:
192.168.1.0
255.255.255.0
any
Huang & Clemm Expires March 4, 2013 [Page 14]
Internet-Draft yang-acl August 2012
4.4. Containers
4.4.1. acls Container
acls container contains a list of named acl. Each acl contains the
following global leaves that applies to acl extensions. acl-arp, acl-
mac, and acl-ip extends the list acl.
o name
o acl-type
o capture-session-id-global
o enable-match-counter-choices: The difference of these two choices
is that enable-match-counter is to collect total match statistics
for all aces verus enable-per-entry-match-counter is to collect
match statistics for each ace.
o match
4.4.2. port-obj-grp Container
port-obj-grp allows to classify protocol port into groups. port-obj-
grp container is a sequence of port ranges. One port-group can apply
to multiple aces. This feature allows multiple ace applies to same
port group. The following is Netconf XML examples of port-obj-grp
and how it is refered from ace.
port-tunnel1
port-tunnel1
gt
8080
Huang & Clemm Expires March 4, 2013 [Page 15]
Internet-Draft yang-acl August 2012
4.4.3. timerange-obj-grp Container
timerange-obj-grp container is list of named entry. Each entry
contains a time-ranges container. Each time-ranges is a sequence of
time-range. Each time-range is a remark (comments for the time-
range), or an absolute time for start or end or both, or a periodic
time for start or end or both. remark is the comments for the time-
range that will be kept in the device. Same time-range can be reused
in different aces. The following is Netconf XML examples of time-
range-entry and how it is referred from ace.
weekday
10
email server maintainance
30
Monday Tuesday Wednesday Thursday Friday
21:00:00
24:00:00
4.4.4. ip-address-obj-grp Container
ip-address-obj-grp container is list of named ip-address-group. Each
ip-address-group is a sequence of ip-address and mask pair or host
and host-address pair. Each ipaddress-group can be referred from ace
by name. The following is Netconf XML examples of ip-address-group
and how it is referred from ace.
HR-VM-IPV6
Huang & Clemm Expires March 4, 2013 [Page 16]
Internet-Draft yang-acl August 2012
10
ipv6
ip
FE80::B3FF:FE1E:8329
128
20
ipv6
host
21DA::2F3B:2AA:FF:FE28:9C5A
Email-Server-IPV4
10
ip
128.107.0,0
255.255.0.0
20
ip
139.207.0.0
255.255.0.0
100
ipv6
permit
group
HR-VM-IPV6
any
Huang & Clemm Expires March 4, 2013 [Page 17]
Internet-Draft yang-acl August 2012
5. acl-ip module
acl-ip is the module that defines IP-ACL. It augments list acl in
acl module.
5.1. Groupings
5.1.1. ACTIONS Grouping
ACTIONS grouping is a reusable grouping for ace action when there is
a match. It has the following leaves:
o action: a mandatory leaf when ace filters match and support permit
and deny two actions now.
o log-choice: enable log when ace filters match. Some device
support log-input to have additional input interface in the log
message when if-feature is enabled.
5.1.2. SRC-PORT-GROUP grouping
SRC-PORT-GROUP
+-- (src-ports)?
+--rw (port-number-or-range)?
| +--:(port-number-range)
| | +--rw src-port-lower? inet:port-number
| | +--rw src-port-upper? inet:port-number
+--:(port-number)
| +--rw src-comparator Comparator
| +--rw src-port? inet:port-number
+-- :(by-name)
+--src-port-group-name
SRC-PORT-GROUP is a reusable group and allow the following three ways
to define a group of ports.
o port-number-range: use src-port-lower and src-port-upper two
leaves to specify a port range. src-port-lower has to less or
equal than src-port-upper.
o port-number: use comparator and src-port two leaves to specify a
port range. See Comparator typedef in the model for the possible
values for comparator leaf.
o port range ref: refer to a named port group defined using port-
obj-grp. For example:
Huang & Clemm Expires March 4, 2013 [Page 18]
Internet-Draft yang-acl August 2012
port-tunnel1
5.1.3. DES-PORT-GROUP grouping
DES-PORT-GROUP
+-- (des-ports)?
+--rw (port-number-or-range)?
| +--:(port-number-range)
| | +--rw des-port-lower? inet:port-number
| | +--rw des-port-upper? inet:port-number
+--:(port-number)
| +--rw des-comparator Comparator
| +--rw des-port? inet:port-number
+-- :(by-name)
+-- des-port-group-name
DES-PORT-GROUP is a reusable group and has a similar structure as
SRC-PORT-GROUP. The reason to have both SRC-PORT-GROUP and DES-PORT-
GROUP is to allow src-port and des-port in the same container..
80
8080
80
8080
5.1.4. IP-ACE-FILTERS Grouping
Huang & Clemm Expires March 4, 2013 [Page 19]
Internet-Draft yang-acl August 2012
IP-ACE-FILTERS
+--rw acl-ip:protocol? c-types:IP-Protocol
+--rw acl-ip:enable-capture? boolean
+--rw acl-ip:capture-session-id? uint32
+--rw acl-ip:fragments? empty
+--rw acl-ip:time-range? acl:Time-Range-Ref
+--SRC-PORT-GROUP
+ DEST-PORT-GROUP
+--rw (packet-length-or-range)?
| +--:(length)
| | +--rw acl-ip:packet-length-comparator acl:Comparator
| | +--rw acl-ip:packet-length uint32
| +--:(range)
| +--rw acl-ip:packet-length-upper uint32
| +--rw acl-ip:packet-length-lower uint32
+--rw acl-ip:tcp-flag-value? c-types:TCP-Flag-Type
+--rw acl-ip:tcp-flag-mask? c-types:TCP-Flag-Type
+--rw acl-ip:tcp-flag-operation? enumeration
IP-ACE-FILTERS defines the following leaves that reused by ipv4 and
ipv6 ace.
o protocol
o enable-capture: The ability to configure ACL capture in order to
selectively monitor traffic on an interface or VLAN. When the
capture option for an ACL rule is enabled, packets that match this
rule are either forwarded or dropped based on the specified permit
or deny action and may also be copied to an alternate destination
port for further analysis.
o capture-session-id: This optional leaf only applies when enable-
capture is true.
o fragments: when presence, it match the non-initial fragment.
o time-range: time-range is to enable packet capture on this filter
for a timerange-group by name. time-range is Time-Range-Ref type
which is a leafref.
o SRC-PORT-GROUP: see Section 5.1.2
o DES-PORT-GROUP: see Section 5.1.3
o packet-length-or-range: packet-length-or-range is to match package
if the pack length is in the range. It allows two ways to specify
packet length range.
Huang & Clemm Expires March 4, 2013 [Page 20]
Internet-Draft yang-acl August 2012
* case length: this is to use comparator and a single packet-
length to specify range.
* case range: this is to use packet-length-lower and packet-
length-upper to specify a range. The value of packet-length-
lower must be lower or equal than the value of packet-length-
upper.
o tcp-flag-value
o tcp-flag-mask
o tcp-flag-operation
o tcp-flag-value, tcp-flag-mask and tcp-flag-operation combinations
is to allow to match any combination of packet tcp flag values.
The following example is to match the packet
tcp flag ack=1, syn=1, and fin=0;
ack syn
ack syn fin
match-all
5.1.5. IPV4-ACE-GROUP Grouping
The following is IPV4-ACE-GROUP tree. IPV4-ACE-GROUP grouping is
used in acl list when acl-type is ip-acl. It is not reused in this
module but to keep acl list data model concise, so the acl list
structure won't be submerged with ACE details. For the definition of
acl list, see section acl list Section 4.4.1.
Huang & Clemm Expires March 4, 2013 [Page 21]
Internet-Draft yang-acl August 2012
+--:IPV4-ACE-GROUP
+--rw ipv4-aces
+--rw ipv4-ace [sequence-num]
+--rw sequence-num Sequence-Number
+--rw (remark-or-filter)?
+--:(remark)
| +--rw remark? string
+--:(packet-filter)
+--rw filter
| +--rw acl-ip:filters
| | +--acl:IP-SOURCE-NETWORK
| | +--acl:IP-DESTINATION-NETWORK
| | +--IP-ACE-FILTERS
| | +--rw (dscp-or-tos)?
| | +--:(dscp)
| | | +--rw dscp? inet:dscp
| | +--:(tos)
| | +--rw tos? c-types:ToS
| | +--rw precedence? c-types:Precedence
| +--rw actions
| | +--ACTIONS
+--ro match? uint64
IPV4-ACE-GROUP contains a sequenced ipv4-ace.
5.1.5.1. ipv4-ace list
An ipv4-ace list is set of rules that is used to filter ipv4 traffic
on a networking device ordered by sequence-num. An ipv4-ace can be a
remark or a-filter. A remark is a comment for the ace that will be
keptin the device. A-filter consists of two parts:
o Filters: this specifies a set of matching criteria that a packet
must satisfy for the rule to be applied.
o Actions: this specifies what to do with the packet when the
filters are matched, for example, to drop the packet.
Here are the filters:
o IP-SOURCE-NETWORK: see Section 4.3.5.
o IP-DESTINATION-NETWORK: Section 4.3.6
o IP-ACE-FILTERS: see Section 5.1.4
Huang & Clemm Expires March 4, 2013 [Page 22]
Internet-Draft yang-acl August 2012
o dscp-or-tos: Section 5.1.5.1.1
5.1.5.1.1. dscp-or-tos choice
dscp-or-tos is to match package on the dscp or tos value.
case dscp: dscp is to match packet on the dscp value.
case tos:This is to match packet on tos and precedence value. ToS
and Precedence typedef is defined in common-types which can be
deprecated when IETF has a standard ToS and Precedence YANG
definition.
5.1.5.1.2. match leaf
match: this is an operational data. It maintains the packet matches
(hits) on the ace.
5.1.6. IPV6-ACE-GROUP Grouping
The following is IPV6-ACE-GROUP tree. IPV6-ACE-GROUP grouping is
used in acl list when acl-type is ip-acl. It is not reused in this
module but to keep acl list data model concise, so the acl list
structure won't be submerged with ACE details. For the definition of
acl list, see section acl list Section 4.4.1.
+--:IPV6-ACE-GROUP
+--rw ipv6-aces
+--rw ipv6-ace [sequence-num]
+--rw sequence-num Sequence-Number
+--rw (remark-or-filter)?
+--:(remark)
| +--rw remark? string
+--:(packet-filter)
+--rw filter
| +--acl:IP-SOURCE-NETWORK
| +--acl:IP-DESTINATION-NETWORK
| +--IP-ACE-FILTERS
| +--rw (dscp-or-tos)?
| | +--:(dscp)
| | | +--rw dscp? inet:dscp
| +--rw igmp-type?
| +--rw actions
| | +--ACTIONS
+--ro match? uint64
Huang & Clemm Expires March 4, 2013 [Page 23]
Internet-Draft yang-acl August 2012
IPV6-ACE-GROUP contains a sequenced ipv6-ace.
5.1.6.1. ipv6-ace list
An ip-ace list is a set of rules that is used to filter ipv4 traffic
on a networking device ordered by sequence-num. . An ip-ace can be a
remark or an ace-filter. A remark is a comment for the ace that will
be keptin the device. Same as ipv4-ace, a filter consists of two
parts:
o Filters: this specifies a set of matching criteria that a packet
must satisfy for the rule to be applied.
o Actions: this specifies what to do with the packet when the
filters are matched, for example, to drop the packet.
Here are the filters:
IP-SOURCE-NETWORK: see Section 4.3.5.
IP-DESTINATION-NETWORK: Section 4.3.6
--IP-ACE-FILTERS: see Section 5.1.4
dscp-or-tos: Section 5.1.6.1.1
igmp-type
5.1.6.1.1. dscp-or-tos choice
Different from ipv4, ipv6 dscp-or-tos is to match package on the dscp
value.
case dscp: dscp is to match packet on the dscp value.
5.1.6.1.2. match leaf
match: this is an operational data. It maintains the packet matches
(hits) on the ace.
5.2. augment
The module "acl-ip" augments the definition of data node "/acl:acls/
acl:acl" with addtional leaves and subcomponents.
afi
Huang & Clemm Expires March 4, 2013 [Page 24]
Internet-Draft yang-acl August 2012
IPV6-ACE-GROUP
IPV4-ACE-GROUP
global-fragments
5.2.1. global-fragments leaf
global-fragments is an optional leaf. It has an enumeration value of
not-set, permit-all, deny-all. not-set is the default value. When
the global-fragments is permit-all or deny-all, it is to permit or
deny the implicit ace fragment filter. Here is an example of
implicit ace and how the implicit ace is affected when global-
fragments is set.
Example 1: The acl configuration from the management interface with
global-fragments is absent.
Huang & Clemm Expires March 4, 2013 [Page 25]
Internet-Draft yang-acl August 2012
YANG instance of this cli configuration:
gragment_test1
ipv4
ip-acl
10
permit
1.1.1.1
16
any
20
permit
2.2.2.2
16
any
By taking all the leaves value out, the above yang can be express in
the following lines:
fragment_test1 ip-acl ipv4
10 permit ip 1.1.1.1/16 any
20 permit ip 2.2.2.2/16 any fragment.
The acl configuration with implicit ace in the device withwill be:
Huang & Clemm Expires March 4, 2013 [Page 26]
Internet-Draft yang-acl August 2012
fragment_test1 ip-acl ipv4
10 permit ip 1.1.1.1/16 any
11 permit ip 1.1.1.1/16 any fragment
20 permit ip 2.2.2.2/16 any fragment.
100 deny any any
110 deny any any fragment
Notice three lines of configuration are implicit.
Example 2: The acl configuration from the management interface with
global-fragments
gragment_test2
ip-acl
deny-all
ipv4
10
permit
1.1.1.1
16
any
20
permit
2.2.2.2
16
any
The acl configuration in the device with implicit aces. The deny-all
void "11 permit ip 1.1.1.1/16 any fragment" ace in previous example.
Huang & Clemm Expires March 4, 2013 [Page 27]
Internet-Draft yang-acl August 2012
By taking all the leaves value out, the above yang can be express in
the following lines:
fragment_test2 ip-acl ipv4 deny-all
10 permit ip 1.1.1.1/16 any
20 permit ip 2.2.2.2/16 any fragment.
fragment_test2 ip-acl ipv4
10 permit ip 1.1.1.1/16 any
20 permit ip 2.2.2.2/16 any fragment.
100 deny any any
110 deny any any fragment
6. acl-mac module
6.1. MAC-ACE-GROUP group
The following is MAC-ACE-GROUP tree. MAC-ACE-GROUP grouping is used
in acl list when acl-type is mac-acl. It is not reused in this
module but to keep acl list data model concise, so the acl list
structure won't be submerged with ACE details. For the definition of
acl list, see section acl list Section 4.4.1.
MAC-ACE-GROUP
+--rw mac-aces
+--rw mac-ace [sequence-num]
+--rw sequence-num Sequence-Number
+--rw (remark-or-ace-filter)?
+--:(remark)
| +--rw remark Remark
+--:(ace-filter)
+--rw filter
| +--acl:MAC-SOURCE-NETWORK
| +--acl:MAC-DESTINATION-NETWORK
| +--rw ethertype? c-types:Ether-Type
| +--rw ethertype-mask? c-types:Ether-Type
| +--rw enable-capture? boolean
| +--rw capture-session-id? uint8
| +--rw cos? c-types:CoS
| +--rw time-range? Time-Range-Ref
| +--rw vlan? c-types:Vlan-Identifier
+-- rw actions
| +--rw action ACL-Action
| +--rw log? boolean
+--ro match? uint64
Huang & Clemm Expires March 4, 2013 [Page 28]
Internet-Draft yang-acl August 2012
MAC-ACE-GROUP has a mac-aces container. The mac-aces container
contains a list of sequenced mac-ace.
6.1.1. mac-ace list
A mac-ace list is a set of rules ordere by sequence-num that is used
to filter traffic on a networking device using information in layer 2
header. A mac-ace can be a remark or an ace-filter. A remark is a
comment for the ace that will be keptin the device. An ace-filter
consists of two parts:
o Filters: this specifies a set of matching criteria that a packet
must satisfy for the rule to be applied.
o Actions: this specifies what to do with the packet when the
filters are matched, for example, to drop the packet.
Here are the filters:
MAC-SOURCE-NETWORK: see Section 4.3.2.
MAC-DESTINATION-NETWORK: Section 4.3.3
ethertype-mask: see definition in "acl-ip" module.
cos
time-range:
vlan
enable-capture
capture-session-id
The definitions and descriptions of the above leaves can be found in
the text of the module "acl-mac"
6.2. augment
The module "acl-mac" augments the definition of data node "/acl:acls/
acl:acl" with addtional leaves and subcomponents.
7. acl-arp module
Huang & Clemm Expires March 4, 2013 [Page 29]
Internet-Draft yang-acl August 2012
7.1. ARP-ACE-GROUP group
The following is ARP-ACE-GROUP. ARP-ACE-GROUP. grouping is used in
acl list when acl-type is arp-acl. It is not reused in this module
but to keep acl list data model concise, so the acl list structure
won't be submerged with ACE details. For the definition of acl list,
see section acl list Section 4.4.1. ARP-ACE-GROUP has a arp-aces
container. The arp-aces container contains a sequenced arp-ace.
+--:ARP-ACE-GROUP
+--rw arp-aces
+--rw arp-ace [sequence-num]
+--rw sequence-num Sequence-Number
+--rw (remark-or-ace-filter)?
+--:(remark)
| +--rw remark string
+--:(ace-filter)
| +--rw filters
| +--rw direction? enumeration
| +--rw acl:IP-SOURCE-NETWORK
| +--rw acl:IP-DESTINATION-NETWORK
| +--rw acl:MAC-SOURCE-NETWORK
| +--rw acl:MAC-DESTINATION-NETWORK
| +--rw enable-capture? boolean
| +--rw capture-session-id? uint32
+--rw actions
| +--rw action ACL-Action
| +--rw log? boolean
+--ro match? uint64
7.2. arp-ace list
An arp-ace list is a set of rules ordere by sequence-num that is used
to filter arp traffic on a networking device. A arp-ace can be a
remark or an ace-filter. A remark is a comment for the ace that will
be keptin the device. An ace-filter consists of two parts:
o Filters: this specifies a set of matching criteria that a packet
must satisfy for the rule to be applied.
o Actions: this specifies what to do with the packet when the
filters are matched, for example, to drop the packet.
Here are the filters
Huang & Clemm Expires March 4, 2013 [Page 30]
Internet-Draft yang-acl August 2012
direction: it is the comments for the ace that will be kept in the
device.
IP-SOURCE-NETWORK: see Section 4.3.5
IP-DESTINATION-NETWORK: Section 4.3.6
MAC-SOURCE-NETWORK: see Section 4.3.2.
MAC-DESTINATION-NETWORK: Section 4.3.3
enable-capture
capture-session-id
The definitions and descriptions of the above leaves can be found in
the text of the module "acl-arp".
7.3. augment
The module "acl-arp" augments the definition of data node "/acl:acls/
acl:acl" with addtional leaves and subcomponents.
8. Data Model Structure
The combined data model for ACL configuration is structured as
follows. "acl" defines the generic components of an acl system.
"acl-ip", "acl-mac", "acl-arp" augment the "acl" module with
additional data nodes that are needed for ip, mac, and arp acl
respectively.
module: acl
+--rw acls
+--rw acl [name]
| +--rw name
| +--rw acl-type
| +--rw enable-capture-global?
| +--rw capture-session-id-global?
| +--rw (enable-match-counter-choices)?
| | +--:(match)
| | | +--rw enable-match-counter?
| | +--:(per-entry-match)
| | +--rw enable-per-entry-match-counter?
| +--ro match?
| +--rw acl-ip:afi?
| +--rw acl-ip:ipv6-aces
| | +--rw acl-ip:ipv6-ace [sequence-num]
| | +--rw acl-ip:sequence-num
Huang & Clemm Expires March 4, 2013 [Page 31]
Internet-Draft yang-acl August 2012
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-ip:remark?
| | +--:(filter)
| | +--rw acl-ip:filters
| | | +--rw acl-ip:ip-source-kind
| | | +--rw (source-address-host-group)?
| | | | +--:(mask)
| | | | | +--rw acl-ip:ip-source-address?
| | | | | +--rw acl-ip:ip-source-mask
| | | | +--:(host-address)
| | | | | +--rw acl-ip:ip-source-host-address
| | | | +--:(group)
| | | | +--rw acl-ip:ip-source-group
| | | +--rw acl-ip:ip-dest-kind IP-Network-Kind
| | | +--rw (dest-mask-host-group)?
| | | | +--:(mask)
| | | | | +--rw acl-ip:ip-dest-address?
| | | | | +--rw acl-ip:ip-dest-mask?
| | | | +--:(host-address)
| | | | | +--rw acl-ip:ip-dest-host-address?
| | | | +--:(group)
| | | | +--rw acl-ip:ip-dest-group?
| | | +--rw acl-ip:protocol?
| | | +--rw acl-ip:enable-capture?
| | | +--rw acl-ip:capture-session-id?
| | | +--rw acl-ip:fragments?
| | | +--rw acl-ip:time-range?
| | | +--rw (src-ports)?
| | | | +--:(port-number-range)
| | | | | +--rw acl-ip:src-port-lower
| | | | | +--rw acl-ip:src-port-upper
| | | | +--:(port-number)
| | | | | +--rw acl-ip:src-comparator
| | | | | +--rw acl-ip:src-port
| | | | +--:(port-group-ref)
| | | | +--rw acl-ip:src-port-group-name
| | | +--rw (des-ports)?
| | | | +--:(port-number-range)
| | | | | +--rw acl-ip:des-port-lower
| | | | | +--rw acl-ip:des-port-upper
| | | | +--:(port-number)
| | | | | +--rw acl-ip:des-comparator
| | | | | +--rw acl-ip:des-port
| | | | +--:(port-group-ref)
| | | | +--rw acl-ip:des-port-group-name
| | | +--rw (packet-length-or-range)?
| | | | +--:(length)
Huang & Clemm Expires March 4, 2013 [Page 32]
Internet-Draft yang-acl August 2012
| | | | | +--rw acl-ip:packet-length-comparator
| | | | | +--rw acl-ip:packet-length
| | | | +--:(range)
| | | | +--rw acl-ip:packet-length-upper
| | | | +--rw acl-ip:packet-length-lower
| | | +--rw acl-ip:tcp-flag-value?
| | | +--rw acl-ip:tcp-flag-mask?
| | | +--rw acl-ip:tcp-flag-operation?
| | | +--rw (dscp-or-tos)?
| | | | +--:(dscp)
| | | | +--rw acl-ip:dscp?
| | | +--rw acl-ip:igmp-type?
| | +--rw acl-ip:actions
| | | +--rw acl-ip:action
| | | +--rw (log-choice)?
| | | +--:(log)
| | | | +--rw acl-ip:log?
| | | +--:(log-input)
| | | +--rw acl-ip:log-input?
| | +--ro acl-ip:match?
| +--rw acl-ip:ipv4-aces
| | +--rw acl-ip:ipv4-ace [sequence-num]
| | +--rw acl-ip:sequence-num
| | +--rw (remark-or-filter)?
| | +--:(remark)
| | | +--rw acl-ip:remark
| | +--:(filter)
| | +--rw acl-ip:filters
| | | +--rw acl-ip:ip-source-kind
| | | +--rw (source-address-host-group)?
| | | | +--:(mask)
| | | | | +--rw acl-ip:ip-source-address?
| | | | | +--rw acl-ip:ip-source-mask
| | | | +--:(host-address)
| | | | | +--rw acl-ip:ip-source-host-address
| | | | +--:(group)
| | | | +--rw acl-ip:ip-source-group
| | | +--rw acl-ip:ip-dest-kind
| | | +--rw (dest-mask-host-group)?
| | | | +--:(mask)
| | | | | +--rw acl-ip:ip-dest-address?
| | | | | +--rw acl-ip:ip-dest-mask?
| | | | +--:(host-address)
| | | | | +--rw acl-ip:ip-dest-host-address?
| | | | +--:(group)
| | | | +--rw acl-ip:ip-dest-group?
| | | +--rw acl-ip:protocol?
| | | +--rw acl-ip:enable-capture?
Huang & Clemm Expires March 4, 2013 [Page 33]
Internet-Draft yang-acl August 2012
| | | +--rw acl-ip:capture-session-id?
| | | +--rw acl-ip:fragments?
| | | +--rw acl-ip:time-range?
| | | +--rw (src-ports)?
| | | | +--:(port-number-range)
| | | | | +--rw acl-ip:src-port-lower
| | | | | +--rw acl-ip:src-port-upper
| | | | +--:(port-number)
| | | | | +--rw acl-ip:src-comparator
| | | | | +--rw acl-ip:src-port
| | | | +--:(port-group-ref)
| | | | +--rw acl-ip:src-port-group-name
| | | +--rw (des-ports)?
| | | | +--:(port-number-range)
| | | | | +--rw acl-ip:des-port-lower
| | | | | +--rw acl-ip:des-port-upper
| | | | +--:(port-number)
| | | | | +--rw acl-ip:des-comparator
| | | | | +--rw acl-ip:des-port
| | | | +--:(port-group-ref)
| | | | +--rw acl-ip:des-port-group-name
| | | +--rw (packet-length-or-range)?
| | | | +--:(length)
| | | | | +--rw acl-ip:packet-length-comparator
| | | | | +--rw acl-ip:packet-length uint32
| | | | +--:(range)
| | | | +--rw acl-ip:packet-length-upper
| | | | +--rw acl-ip:packet-length-lower
| | | +--rw acl-ip:tcp-flag-value?
| | | +--rw acl-ip:tcp-flag-mask?
| | | +--rw acl-ip:tcp-flag-operation?
| | | +--rw (dscp-or-tos)?
| | | +--:(dscp)
| | | | +--rw acl-ip:dscp?
| | | +--:(tos)
| | | +--rw acl-ip:tos?
| | | +--rw acl-ip:precedence?
| | +--rw acl-ip:actions
| | | +--rw acl-ip:action
| | | +--rw (log-choice)?
| | | +--:(log)
| | | | +--rw acl-ip:log?
| | | +--:(log-input)
| | | +--rw acl-ip:log-input?
| | +--ro acl-ip:match?
| +--rw acl-ip:global-fragments?
| +--rw acl-mac:mac-aces
| | +--rw acl-mac:mac-ace [sequence-num]
Huang & Clemm Expires March 4, 2013 [Page 34]
Internet-Draft yang-acl August 2012
| | +--rw acl-mac:sequence-num
| | +--rw (remark-or-ace-filter)
| | +--:(remark)
| | | +--rw acl-mac:remark
| | +--:(filter)
| | +--rw acl-mac:filters
| | | +--rw acl-mac:mac-source-kind?
| | | +--rw (source-network)?
| | | | +--:(address)
| | | | | +--rw acl-mac:source-address
| | | | | +--rw acl-mac:source-address-mask
| | | | +--:(host)
| | | | +--rw acl-mac:source-host-name
| | | +--rw acl-mac:mac-dest-kind?
| | | +--rw (dest-network)?
| | | | +--:(address)
| | | | | +--rw acl-mac:destination-address
| | | | | +--rw acl-mac:destination-address-mask
| | | | +--:(host)
| | | | +--rw acl-mac:dest-host-name
| | | +--rw acl-mac:ethertype?
| | | +--rw acl-mac:ethertype-mask?
| | | +--rw acl-mac:cos?
| | | +--rw acl-mac:time-range?
| | | +--rw acl-mac:vlan?
| | | +--rw acl-mac:enable-capture?
| | | +--rw acl-mac:capture-session-id?
| | +--rw acl-mac:actions
| | | +--rw acl-mac:action
| | | +--rw acl-mac:log?
| | +--ro acl-mac:match?
| +--rw acl-arp:arp-aces
| +--rw acl-arp:arp-ace [sequence-num]
| +--rw acl-arp:sequence-num
| +--rw (remark-or-ace-filter)?
| +--:(remark)
| | +--rw acl-arp:remark
| +--:(filter)
| +--rw acl-arp:filters
| | +--rw acl-arp:direction?
| | +--rw acl-arp:ip-source-kind
| | +--rw (source-address-host-group)?
| | | +--:(mask)
| | | | +--rw acl-arp:ip-source-address?
| | | | +--rw acl-arp:ip-source-mask
| | | +--:(host-address)
| | | | +--rw acl-arp:ip-source-host-address
| | | +--:(group)
Huang & Clemm Expires March 4, 2013 [Page 35]
Internet-Draft yang-acl August 2012
| | | +--rw acl-arp:ip-source-group
| | +--rw acl-arp:ip-dest-kind
| | +--rw (dest-mask-length-host-group)?
| | | +--:(mask)
| | | | +--rw acl-arp:ip-dest-address?
| | | | +--rw acl-arp:ip-dest-mask?
| | | +--:(host-address)
| | | | +--rw acl-arp:ip-dest-host-address?
| | | +--:(group)
| | | +--rw acl-arp:ip-dest-group?
| | +--rw acl-arp:mac-source-kind?
| | +--rw (source-network)?
| | | +--:(address)
| | | | +--rw acl-arp:source-address
| | | | +--rw acl-arp:source-address-mask
yang:mac-address
| | | +--:(host)
| | | +--rw acl-arp:source-host-name
| | +--rw acl-arp:mac-dest-kind?
| | +--rw (dest-network)?
| | | +--:(address)
| | | | +--rw acl-arp:destination-address
| | | | +--rw acl-arp:destination-address-mask
| | | +--:(host)
| | | +--rw acl-arp:dest-host-name
| | +--rw acl-arp:enable-capture?
| | +--rw acl-arp:capture-session-id?
| +--rw acl-arp:actions
| | +--rw acl-arp:action
| | +--rw acl-arp:log?
| +--ro acl-arp:match?
+--rw port-obj-grp
| +--rw port-group [name]
| +--rw name string
| +--rw groups
| +--rw groups [sequence-num]
| +--rw sequence-num
| +--rw (port-number-or-range)?
| +--:(port-number-range)
| | +--rw port-lower
| | +--rw port-upper
| +--:(port-number)
| +--rw comparator
| +--rw port
+--rw timerange-obj-grp
| +--rw timerange-group [name]
| +--rw name string
| +--rw time-ranges
Huang & Clemm Expires March 4, 2013 [Page 36]
Internet-Draft yang-acl August 2012
| +--rw time-range [sequence-num]
| +--rw sequence-num
| +--rw (range-type)?
| +--:(remark)
| | +--rw remark?
| +--:(absolute)
| | +--rw absolute
| | +--rw start?
| | +--rw end?
| +--:(periodic)
| +--rw periodic
| +--rw weekdays?
| +--rw start?
| +--rw end?
+--rw ip-address-obj-grp
+--rw ip-address-group [name]
+--rw name
+--rw afi?
+--rw ip-addresses
+--rw ip-address [sequence-num]
+--rw sequence-num
+--rw ip-address-kind?
+--rw (mask-or-host)?
+--:(mask)
| +--rw ip-address?
| +--rw ip-mask
+--:(host)
+--rw ip-host-address
rpcs:
+---x reset-match
+--ro input
+--ro name string
+--ro sequence-num? Sequence-Number
module: acl-ip
module: acl-mac
module: acl-arp
Figure 3
9. ACL YANG Module
This module imports type definitions from [RFC6021].
file "acl@2012-08-30.yang"
module acl {
namespace "urn:cisco:params:xml:ns:yang:acl";
Huang & Clemm Expires March 4, 2013 [Page 37]
Internet-Draft yang-acl August 2012
// replace with IANA namespace when assigned
prefix acl;
import ietf-inet-types {
prefix "inet";
}
import ietf-yang-types {
prefix "yang";
}
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: http://tools.ietf.org/wg/netmod/
WG List: netmod@ietf.org
WG Chair: David Kessens
david.kessens@nsn.com
WG Chair: Juergen Schoenwaelder
j.schoenwaelder@jacobs-university.de
Editor: Lisa Huang
yihuan@cisco.com
Editor: Alexander Clemm
alex@cisco.com";
description
"This YANG module defines a component that describing the
configuration of Access Control Lists (ACLs).
An ACL is an ordered set of rules and actions used to filter
traffic. Each set of rules and actions is represented
as an Access Control Entries (ACE). Each ACE is evaluated
sequentially. When the rule matches then action for that
rule is applied to the packet.
There are three types of ACL.
IP ACLs - IP ACLs are ordered sets of rules that can use to
filter traffic based on IP information in the Layer 3
header of packets.
The device applies IP ACLs only to IP traffic. IP ACL
can be IPv4 or IPv6.
Huang & Clemm Expires March 4, 2013 [Page 38]
Internet-Draft yang-acl August 2012
MAC ACLs - MAC ACLs are used to filter traffic using the
information in the Layer 2 header of each packet.
MAC ACLs are by default only applied to non-IP
traffic; however, Layer 2 interfaces can be configured
to apply MAC ACLs to all traffic.
ARP ACLs - The device applies ARP ACLs to IP traffic.
This module should be used with acl-ip, acl-arp, or acl-mac
depends on what feature the device supports.
This YANG module also includes auxiliary definitions that
are needed in conjunction with configuration of ACLs, such as
reusable containers and references for ports and IP.
Terms and Acronyms
ACE (ace): Access Control Entry
ACL (acl): Access Control List
AFI (afi): Authority and Format Identifier (Address
Field Identifier)
ARP (arp): Address Resolution Protocol
IP (ip): Internet Protocol
IPv4 (ipv4):Internet Protocol Version 4
IPv6 (ipv6): Internet Protocol Version 6
MAC: Media Access Control
TCP (tcp): Transmission Control Protocol
TTL (ttl): Time to Live
VLAN (vlan): Virtual Local Area Network
";
revision 2012-08-31 {
description "Initial revision. ";
}
feature host-by-name {
description
"The capability to reference a host by name.";
Huang & Clemm Expires March 4, 2013 [Page 39]
Internet-Draft yang-acl August 2012
}
feature log-input {
description
"The ability to log messages upon the matching of ACLs.";
}
feature time-to-live {
description "The ability to filter packets based on their
time-to-live (TTL) value (0 to 255)";
reference "ACL Support for Filtering on TTL Value";
}
feature ethertype-mask {
description
"The ability to fiter packets based on ether-type mask
in hex 0x0-0xFFFF.";
}
feature flow-label {
description
"The ability to filter packets based on flow lable.
The 20-bit Flow Label field in the IPv6 header
is used by a source to label packets
of a flow. This is an IPv6 ACEs option.";
reference "RFC 3697 IPv6 Flow Label Specification";
}
feature match-counter {
description
"The ability to maintain global or local match statistics
for each ACL ruels.";
}
feature port-group {
description
"The ability to define named groups for lists of ports. ";
}
feature ip-group-address {
description
"The ability to define named groups for lists of
ip addresses. ";
}
feature arp-acl {
description "The ability to support ARP ACLs.";
}
feature capture-session-id {
Huang & Clemm Expires March 4, 2013 [Page 40]
Internet-Draft yang-acl August 2012
description
"The ability to configure ACL capture in order to
selectively monitor traffic on an interface or VLAN.
When the capture option for an ACL rule
is enabled, packets that match this rule are
either forwarded or dropped based on the specified permit
or deny action and may also be copied to an alternate
destination port for further analysis.
An ACL rule with the capture option can be applied
as follows:
On a VLAN
In the ingress direction on all interfaces
In the egress direction on all Layer 3 interfaces
The statistics data for the capture-session are capture
in the device where the ACL rule applied to.";
}
feature packet-length {
description "The ability to filter packets by packet length";
}
identity acl-type {
description "Base acl type for all ACL";
}
identity mac-acl {
base acl-type;
description "layer 2 ACL type";
}
identity ip-acl {
base "acl-type";
description "layer 3 ACL type";
}
identity arp-acl {
base "acl-type";
description "ARP ACL type";
}
/* Types */
typedef Comparator {
description "A data type used to express comparator string";
type enumeration {
enum "eq" {
value 0;
description "match only equal to any giving number.";
Huang & Clemm Expires March 4, 2013 [Page 41]
Internet-Draft yang-acl August 2012
}
enum "gt" {
value 1;
description
"match only greater than any giving number.";
}
enum "lt" {
value 2;
description
"match only lower than any giving number.";
}
enum "neq" {
value 3;
description
"match only not equal to any giving number";
}
}
}
typedef ACL-Action {
description "An enumeration data type to express acl
action when match.";
type enumeration {
enum permit {
description "Apply permit action to the traffic";
}
enum deny {
description "Apply deny action to the traffic";
}
}
}
typedef IP-Network-Kind {
description "A enumeration to indicate the network to be
expressed as an IP address and mask
or simply identify a system as a host,
or as a member of a pre-defined address group,
or as any system.";
type enumeration {
enum ip {
description "Used with address and mask couple
to express network.
";
}
enum any {
description "To express Any network or address.
Use the any keyword as an abbreviation
Huang & Clemm Expires March 4, 2013 [Page 42]
Internet-Draft yang-acl August 2012
for an address and a mask of 0.0.0.0
255.255.255.255. For example:
0.0.0.0/255.255.255.255 means 'any'";
}
enum host {
description "Used with host address to express a
single host
Use the host address(or name)
combination is the same as an address
and mask of address 0.0.0.0.
For example: '10.1.1.2/0.0.0.0' is the same
as 'host 10.1.1.2'";
}
enum group {
description "Use the group keyword and group name
to refer to a pre-defined address object group
which is a list of address and mask.";
}
}
}
typedef MAC-Network-Kind {
description
"A enumeration data type to express the different ways
to express network or address ";
type enumeration {
enum mac {
description "Used with address and mask couple
to express network.";
}
enum any {
description "To express Any network or address";
}
enum host {
description " Use the host address
combination as an abbreviation for an address
and wildcard of address 0.0.0.0";
}
}
}
typedef Sequence-Number {
description
"An data type based on uint32 to determine the order
in which the statements within the access list will
be evaluated.";
type uint32 {
range "1..2147483646";
Huang & Clemm Expires March 4, 2013 [Page 43]
Internet-Draft yang-acl August 2012
}
}
typedef Remark {
type string {
length "0..100";
}
}
typedef Acl-Type-Ref {
description
"This type is used to refer to an Access Control List
(ACL) type";
type identityref {
base "acl-type";
}
}
typedef Acl-Ref {
description "This type refers to an ACL.";
type leafref {
path "/acl:acls/acl:acl/acl:name";
}
}
typedef Port-Group-Ref {
description
"This type is used to refer to a Portgroup object.";
type leafref {
path "/acls/port-obj-grp/port-group/name";
}
}
typedef IP-Address-Group-Ref {
description
"This type is used to refer to a time range object.";
type leafref {
path "/acls/ip-address-obj-grp/ip-address-group/name";
}
}
typedef Time-Range-Ref {
description
"This type is used to refer to a time range object.";
type leafref {
path "/acls/timerange-obj-grp/timerange-group/name";
Huang & Clemm Expires March 4, 2013 [Page 44]
Internet-Draft yang-acl August 2012
}
}
grouping PORT-GROUP {
description
"Using comparator and port, or port-upper and port-lower
to specify a port range. ";
choice port-number-or-range {
case port-number-range {
description
"Port group includes all ports between port-lower
and port-upper (including those)";
leaf port-lower {
type inet:port-number;
description "Lower Port number.";
mandatory true;
}
leaf port-upper {
type inet:port-number;
description "Upper Port number.";
mandatory true;
must "../port-lower <= ../port-upper";
}
}
case port-number {
description
"Port group includes all ports that are greater
than, greater or equal, less than, less or equal,
or not equal the port, per the indicated
comparator.
It is possible for the port group to be empty
(for example, in case a port group that
is less than the minimum port number is
specified).";
leaf comparator {
type Comparator;
mandatory true;
}
leaf port {
type inet:port-number;
description "Port number.";
mandatory true;
}
}
}
}
Huang & Clemm Expires March 4, 2013 [Page 45]
Internet-Draft yang-acl August 2012
/*
* MAC-SOURCE-ADDRESS and MAC-DESTINATION-ADDRESS
*/
grouping MAC-SOURCE-NETWORK {
description "MAC address and mask pair for source.";
leaf mac-source-kind {
type MAC-Network-Kind ;
}
choice source-network {
when "mac-source-kind != 'any'" ;
case address {
when "mac-source-kind = 'mac'" ;
leaf source-address {
type yang:mac-address;
mandatory true;
description "A source MAC address.";
}
leaf source-address-mask {
type yang:mac-address;
mandatory true;
}
}
case host {
when "mac-source-kind = 'host'" ;
leaf source-host-name {
type inet:host;
mandatory true;
}
}
}
}
grouping MAC-DESTINATION-NETWORK {
description "MAC address and mask pair for destination.";
leaf mac-dest-kind {
type MAC-Network-Kind ;
}
choice dest-network {
when "mac-dest-kind != 'any'" ;
case address {
when "mac-dest-kind = 'mac'" ;
leaf dest-address {
type yang:mac-address;
mandatory true;
description "A destination MAC address";
}
leaf dest-address-mask {
type yang:mac-address;
Huang & Clemm Expires March 4, 2013 [Page 46]
Internet-Draft yang-acl August 2012
mandatory true;
}
}
case host {
when "mac-dest-kind = 'host'" ;
leaf dest-host-name {
type inet:host;
mandatory true;
}
}
}
}
grouping IP-ADDRESS-AND-MASK {
description "Reusable IP address and mask pair.";
leaf ip-address-kind {
type IP-Network-Kind ;
}
choice mask-or-host {
when "ip-address-kind != 'any'";
case mask {
when "ip-address-kind = 'ip'" ;
leaf ip-address {
type inet:ip-address;
}
leaf ip-mask {
type inet:ip-prefix;
mandatory true;
}
}
case host {
when "ip-address-kind = 'host'";
leaf ip-host-address {
type inet:host;
mandatory true;
}
}
}
}
grouping IP-SOURCE-NETWORK {
description "Reusable IP address and mask pair.";
leaf ip-source-kind {
type IP-Network-Kind ;
mandatory true;
Huang & Clemm Expires March 4, 2013 [Page 47]
Internet-Draft yang-acl August 2012
}
choice source-address-host-group {
when "ip-source-kind != 'any'";
case mask {
when "ip-source-kind = 'ip'" ;
leaf ip-source-address {
type inet:ip-address;
}
leaf ip-source-mask {
type inet:ip-prefix;
mandatory true;
}
}
case host {
when "ip-source-kind = 'host'";
leaf ip-source-host-address {
type inet:host;
mandatory true;
}
}
case group {
when "ip-source-kind = 'group'";
leaf ip-source-group {
type IP-Address-Group-Ref;
mandatory true;
}
if-feature ip-group-address;
}
}
}
grouping IP-DESTINATION-NETWORK {
description
"Reusable IP address and mask pair for destination.";
leaf ip-dest-kind {
type IP-Network-Kind ;
mandatory true;
}
choice dest-address-host-group {
when "ip-dest-kind != 'any'";
case mask {
when "ip-dest-kind = 'ip'" ;
leaf ip-dest-address {
type inet:ip-address;
}
leaf ip-dest-mask {
type inet:ip-prefix;
Huang & Clemm Expires March 4, 2013 [Page 48]
Internet-Draft yang-acl August 2012
}
}
case host-address {
when "ip-dest-address = 'host'";
leaf ip-dest-host-address {
type inet:host;
}
}
case group {
when "ip-dest-address = 'group'";
leaf ip-dest-group {
type IP-Address-Group-Ref;
}
}
}
}
container acls {
description
"This is the top container that contains a list of
named ACL and reusable acl object groups.";
list acl {
key name;
leaf name {
description "ACL/access group name.";
type string;
}
leaf acl-type {
type Acl-Type-Ref;
description "Type of ACL";
mandatory true;
}
leaf enable-capture-global{
type boolean;
description "Enable packet capture on this filter
for this session. Session ID range is 1 to 48";
default "false";
}
leaf capture-session-id-global {
when "../enable-capture-global = 'true'";
type uint32 {
range "1..48";
}
if-feature capture-session-id;
description "Enable packet capture on this filter
for this session. Session ID range is 1 to 48";
}
Huang & Clemm Expires March 4, 2013 [Page 49]
Internet-Draft yang-acl August 2012
choice enable-match-counter-choices {
if-feature match-counter;
case match {
leaf enable-match-counter {
type boolean;
description
"Eanble to collect statistics for the ACL";
default false;
}
}
case per-entry-match {
leaf enable-per-entry-match-counter {
type boolean;
description "Enable to collect match
statistics for each ACL entry(ACE).";
default false;
}
}
}
leaf match {
if-feature match-counter;
config false;
type uint64;
description
"The total packet that have matched for the
particular access list";
}
}
container port-obj-grp {
list port-group { //CLI: object-group ip port foogroup
key "name";
leaf name {
type string;
}
container groups {
list groups {
key "sequence-num";
leaf sequence-num {
type Sequence-Number;
}
//unique "comparator port-number
//port-lower port-upper";
uses PORT-GROUP;
}
}
Huang & Clemm Expires March 4, 2013 [Page 50]
Internet-Draft yang-acl August 2012
}
}
container timerange-obj-grp {
description "Define time range entries to restrict
the access. The time range is identified by a name
and then referenced by a function, so that those
time restrictions are imposed on the function itself.";
list timerange-group {
key "name";
leaf name {
type string;
mandatory true;
}
container time-ranges {
list time-range {
key "sequence-num";
leaf sequence-num {
type Sequence-Number;
mandatory true;
description
"Sequence number. This number
determines the order of the statements
in the timerange list.
Range is 1 to 2147483646. ";
}
choice range-type {
case remark {
leaf remark {
type string;
description "The remark is the
comments about each time range
which is to make
the time range entry easier for
the network administrator to
understand";
}
}
case absolute {
container absolute {
description
"Absolute time and date that
the associated function starts
going into effect.";
leaf start {
type yang:date-and-time;
Huang & Clemm Expires March 4, 2013 [Page 51]
Internet-Draft yang-acl August 2012
description "Absolute start
time and date";
}
leaf end {
type yang:date-and-time;
description
"Absolute end time and
date";
}
}
}
case periodic {
container periodic {
description "To specify a periodic
time and date.";
leaf weekdays {
type bits {
bit Sunday {
position 0;
}
bit Monday {
position 1;
}
bit Tuesday {
position 2;
}
bit Wednesday {
position 3;
}
bit Thursday {
position 4;
}
bit Friday {
position 5;
}
bit Saturday {
position 6;
}
}
}
leaf start {
type yang:timestamp;
description "Start time";
}
leaf end {
type yang:timestamp;
description "End time";
Huang & Clemm Expires March 4, 2013 [Page 52]
Internet-Draft yang-acl August 2012
}
}
}
}
}
}
}
}
container ip-address-obj-grp {
description
"This contains a list of named ip address group. Each
group defines a range of address and mask pair.";
list ip-address-group {
key "name";
leaf name {
type string;
}
leaf afi {
default "ipv4";
type inet:ip-version;
description "Address Field Identifier (AFI).";
}
container ip-addresses {
list ip-address {
key "sequence-num";
leaf sequence-num {
type Sequence-Number;
mandatory true;
description
"Sequence number. This number
determines the order of the statements
in the timerange list. Range is 1 to
2147483646. ";
}
uses IP-ADDRESS-AND-MASK ;
//unique "ip-address ip-mask";
//unique "ip-host-address";
}
}
}
}
}
rpc reset-match-counter {
description "This RPC is to reset the statistics for the
ACL matches.
Huang & Clemm Expires March 4, 2013 [Page 53]
Internet-Draft yang-acl August 2012
When name is the only input, it
clears ACL match statistics and individual
ACE match statistics.
When name and sequence-numer are both inputs, it clears
the ACE match statistics.";
input {
leaf name {
type string;
mandatory true;
description "This name is the acl name.";
}
leaf sequence-num {
type Sequence-Number;
description
"This number is the ACE sequence-num.";
}
}
}
}
10. ACL-IP YANG Module
This module imports type definitions from [RFC6021] and common-types
yang defined with acl model.
module acl-ip {
namespace "urn:cisco:params:xml:ns:yang:acl-ip";
// replace with IANA namespace when assigned
prefix acl-ip;
import acl { prefix acl; }
import ietf-inet-types {
prefix "inet";
}
import common-types {
prefix "c-types";
}
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
Huang & Clemm Expires March 4, 2013 [Page 54]
Internet-Draft yang-acl August 2012
"WG Web: http://tools.ietf.org/wg/netmod/
WG List: netmod@ietf.org
WG Chair: David Kessens
david.kessens@nsn.com
WG Chair: Juergen Schoenwaelder
j.schoenwaelder@jacobs-university.de
Editor: Lisa Huang
yihuan@cisco.com
Editor: Alexander Clemm
alex@cisco.com";
description
"This YANG module augments the 'acl' module with configuration
and operational data for IPv4 and IPv6 access control list.
An ACL is an ordered set of rules and actions used to filter
traffic.
Each set of rules and actions is represented as an Access
Control Entries (ACE). Each ACE is evaluated sequentially.
When the rule matches then action for that rule is applied
to the packet.
IP ACLs are ordered sets of rules that can use to
filter traffic based on IP information in the Layer 3 header
of packets.
The device applies IP ACLs only to IP traffic. IP ACL
can be IPv4 or IPv6.
Terms and Acronyms
ACE (ace): Access Control Entry
ACL (acl): Access Control List
AFI (afi): Authority and Format Identifier (Address Field
Identifier)
DSCP (dscp): Differentiated Services Code Point
ICMP (icmp): Internet Control Message Protocol
IGMP (igmp): Internet Group Management Protocol
IP (ip): Internet Protocol
Huang & Clemm Expires March 4, 2013 [Page 55]
Internet-Draft yang-acl August 2012
IPv4 (ipv4):Internet Protocol Version 4
IPv6 (ipv6): Internet Protocol Version 6
QoS: Quality of Service
TCP (tcp): Transmission Control Protocol
ToS (tos): Type of Service
TTL (ttl): Time to Live
UDP (udp): User Datagram Protocol
VLAN (vlan): Virtual Local Area Network
VRF(vrf) : Virtual Routing and Forwarding
";
revision 2012-08-31 {
description "Initial revision. ";
}
grouping ACTIONS {
leaf action {
type acl:ACL-Action;
mandatory true;
description "Permit/deny action.";
}
choice log-choice {
case log {
leaf log {
type empty;
description
"Causes an informational
logging message about the
packet that matches the entry
to be sent to the console.";
}
}
case log-input {
leaf log-input {
type empty;
if-feature acl:log-input;
description
"Provides the same function
as the enable-log leaf, except
that the logging message also
Huang & Clemm Expires March 4, 2013 [Page 56]
Internet-Draft yang-acl August 2012
includes the input interface";
}
}
}
}
grouping SRC-PORT-GROUP {
description
"Using comparator and port, or port-upper and port-lower
to specify a port range. ";
choice src-ports {
case port-number-range {
description
"Port group includes all ports between port-lower
and port-upper (including those)";
leaf src-port-lower {
type inet:port-number;
description "Lower Port number.";
mandatory true;
}
leaf src-port-upper {
type inet:port-number;
description "Upper Port number.";
mandatory true;
must "../src-port-lower <= ../src-port-upper";
}
}
case port-number {
description
"Port group includes all ports that are greater
than, greater or equal, less than, less or equal,
or not equal the port, per the indicated
comparator. It is possible for the port group
to be empty (for example, in case a port group
that is less than the minimum port number is
specified).";
leaf src-comparator {
type acl:Comparator;
mandatory true;
}
leaf src-port {
type inet:port-number;
description "Port number.";
mandatory true;
}
}
case port-group-ref {
Huang & Clemm Expires March 4, 2013 [Page 57]
Internet-Draft yang-acl August 2012
if-feature acl:port-group;
leaf src-port-group-name {
type acl:Port-Group-Ref;
mandatory true;
description
"Reference a port group by the Port
Group name.";
}
}
}
}
grouping DES-PORT-GROUP {
description "Using comparator and port, or port-upper and
port-lower to specify a port range. ";
choice des-ports {
case port-number-range {
description "Port group includes all ports between
port-lower and port-upper (including those)";
leaf des-port-lower {
type inet:port-number;
description "Lower Port number.";
mandatory true;
}
leaf des-port-upper {
type inet:port-number;
description "Upper Port number.";
mandatory true;
must "../des-port-lower <= ../des-port-upper";
}
}
case port-number {
description "Port group includes all ports that
are greater than, greater or equal, less than,
less or equal, or not equal the port, per the
indicated comparator. It is possible for the
port group to be empty (for example, in case a
port group that is less than the minimum port
number is specified).";
leaf des-comparator {
type acl:Comparator;
mandatory true;
}
leaf des-port {
type inet:port-number;
description "Port number.";
mandatory true;
}
Huang & Clemm Expires March 4, 2013 [Page 58]
Internet-Draft yang-acl August 2012
}
case port-group-ref {
if-feature acl:port-group;
leaf des-port-group-name {
type acl:Port-Group-Ref;
mandatory true;
description
"Reference a port group by the Port Group name.";
}
}
}
}
grouping IP-ACE-FILTERS {
leaf protocol {
type c-types:IP-Protocol;
description "IP protocol number.";
}
leaf enable-capture {
type boolean ;
description
"Enable packet capture on this filter
for this session.";
}
leaf capture-session-id {
when "../enable-capture = 'true'";
type uint32 {
range "1..48";
}
description
"Enable packet capture on this filter
for this session id.";
if-feature acl:capture-session-id;
}
leaf fragments {
type empty;
description "Check non-initial fragments";
}
leaf time-range {
type acl:Time-Range-Ref;
description
"Refer a time range object by
name (Max Size 64).";
}
uses SRC-PORT-GROUP {
when
Huang & Clemm Expires March 4, 2013 [Page 59]
Internet-Draft yang-acl August 2012
"../protocol = '6' or
../protocol = '17' or
../protocol = '132'";
description
"Apply only when the protocol is TCP,
UDP or SCTP.";
}
uses DES-PORT-GROUP {
when
"../protocol = '6' or
../protocol = '17' or
../protocol = '132'";
description
"Apply only when the protocol is TCP,
UDP or SCTP.";
}
leaf icmp-type {
when "../protocol = '1'";
type c-types:ICMP-Type;
description
"ICMP message type number.
Apply only when the protocol is icmp";
}
leaf icmp-code {
when "boolean(../icmp-type) ";
type c-types:ICMP-Code;
description
"ICMP subtype for a given icmp type.";
}
choice packet-length-or-range {
if-feature acl:packet-length;
case length {
leaf packet-length-comparator {
type acl:Comparator;
description
"Operant that compare the packet
length. Operands are lt (less than),
gt (greater than), eq (equal), and neq
(not equal).";
mandatory true;
}
leaf packet-length {
type uint32 {
range "20..9210";
}
Huang & Clemm Expires March 4, 2013 [Page 60]
Internet-Draft yang-acl August 2012
description
"Packet legth value for
operation gt, eq, etc, other
than range";
mandatory true;
}
}
case range {
leaf packet-length-upper {
type uint32 {
range "20..9210";
}
description "Upper Packet legth";
mandatory true;
}
leaf packet-length-lower {
type uint32 {
range "20..9210";
}
description "Lower packet length";
must
"number(../packet-length-lower) <=
number(../packet-length-upper)";
mandatory true;
}
description
"Packet operater 'range' takes
both lower and upper value.";
}
}
leaf tcp-flag-value {
type c-types:TCP-Flag-Type ;
description "TCP flag bits that needs to be checked";
}
leaf tcp-flag-mask {
when "boolean(../tcp-flag-value)" ;
type c-types:TCP-Flag-Type ;
description "TCP flag bit that needs to be checked";
}
leaf tcp-flag-operation {
when "boolean(../tcp-flag-value)" ;
description
"TCP flag Match option.
A match occurs if the TCP
datagram has certain TCP flags
set or not set. You use the
Huang & Clemm Expires March 4, 2013 [Page 61]
Internet-Draft yang-acl August 2012
match-any keyword to allow a match
to occur if any of the specified
TCP flags are present, or you can
use the match-all keyword to allow
a match to occur only if all of
the specified TCP flags are
present. You must follow the
match-any and match-all keywords
with the + or - keyword and the
flag-name argument to match on
one or more TCP flags. ";
default match-any;
type enumeration {
enum match-any {
description "match any";
}
enum match-all {
description "match all";
}
}
}
choice ttl-value-or-range {
if-feature acl:time-to-live;
case value {
leaf ttl-comparator {
type Comparator;
description
"Compares the TTL value in the packet
to the TTL value specified in this
ACE statement. Operands are lt (less
than), gt (greater than), and eq
(equal), neq (not equal).";
}
leaf ttl-value {
type c-types:Time-to-Live;
}
}
case range {
leaf ttl-value-lower {
type c-types:Time-to-Live;
description "Lower ttl number.";
}
leaf ttl-value--upper {
type c-types:Time-to-Live;
description "Upper ttl number.";
Huang & Clemm Expires March 4, 2013 [Page 62]
Internet-Draft yang-acl August 2012
}
}
}
}
grouping IPV4-ACE-GROUP {
description "Layer 3 Access Control Entry (ACE).";
container ipv4-aces {
description
" The ip-aces container contains a list of ip-ace.
Each ip-ace is made of a sequence number and a choice
of remark(comment) or filter. The filter requires a
mandatory action (permit/deny) and one or more options
such as source-address with mask,ttl etc";
list ipv4-ace {
key "sequence-num";
description "Layer 3 Access Control Element (ACE)";
leaf sequence-num {
type acl:Sequence-Number;
description "This number determines the order in
which the statements within the access list
will be evaluated.";
}
choice remark-or-filter {
case remark {
leaf remark {
type acl:Remark;
mandatory true;
description "A remark is a comment that
can be inserted into an ACL in order
to make the access list easier for
the network administrator to
understand.
It is retained to facilitate
co-existence with CLI.";
}
}
case filter {
container filters {
uses acl:IP-SOURCE-NETWORK;
uses acl:IP-DESTINATION-NETWORK;
uses IP-ACE-FILTERS ;
Huang & Clemm Expires March 4, 2013 [Page 63]
Internet-Draft yang-acl August 2012
choice dscp-or-tos {
case dscp {
leaf dscp {
type inet:dscp;
description
"Match packets with given
dscp value";
}
}
case tos {
leaf tos {
type c-types:ToS;
description
"Match packets with
given TOS value";
}
leaf precedence {
when "boolean(../tos)" ;
type c-types:Precedence;
description
"Match packets with given
precedence value";
}
}
}
}
container actions {
uses ACTIONS ;
}
leaf match {
config false;
type uint64;
description "The total packet that have
matched for the particular ACE";
}
}
}
}
}
}
grouping IPV6-ACE-GROUP {
description "Layer 3 Access Control Entry (ACE).";
Huang & Clemm Expires March 4, 2013 [Page 64]
Internet-Draft yang-acl August 2012
container ipv6-aces {
description
" The ip-aces container contains a list of ip-ace.
Each ip-ace is made of a sequence number and a
choice of remark(comment) or filter. The filter
requires a mandatory action (permit/deny) and one or
more options such as source-address with mask,ttl etc";
list ipv6-ace {
key "sequence-num";
description "Layer 3 Access Control Element (ACE)";
leaf sequence-num {
type acl:Sequence-Number;
description "This number determines the order in
which the statements within the access list
will be evaluated.";
}
choice remark-or-filter {
case remark {
leaf remark {
type string {
length "0..100";
}
description "The remark is the comments
about each acl which is to make the
access list easier for the network
administrator to understand.";
}
}
case filter {
container filters {
uses acl:IP-SOURCE-NETWORK;
uses acl:IP-DESTINATION-NETWORK;
uses IP-ACE-FILTERS ;
choice dscp-or-tos {
case dscp {
leaf dscp {
type inet:dscp;
description
"Match packets with given
dscp value";
}
}
}
Huang & Clemm Expires March 4, 2013 [Page 65]
Internet-Draft yang-acl August 2012
leaf igmp-type {
when
"../protocol = '2' ";
type c-types:IGMP-Code;
description
"IGMP message type (0 to 15) for
filtering IGMP packets. Apply only
when the protocol is igmp in ipv4";
}
leaf flow-label {
when
"../protocol = '17'";
type uint64 {
range "0..1048575";
}
description
"Flow label value. Apply only when
the protocol is UDP in ipv6.";
reference
"RFC3697 IPv6 Flow Label
Specification";
if-feature acl:flow-label;
}
}
container actions {
uses ACTIONS ;
}
leaf match {
config false;
type uint64;
description
"The total packet that have matched for
the particular ACE";
}
}
}
}
}
}
augment "/acl:acls/acl:acl" {
Huang & Clemm Expires March 4, 2013 [Page 66]
Internet-Draft yang-acl August 2012
when "acl:acl-type = 'ip-acl'";
leaf afi {
type inet:ip-version ;
default "ipv4";
}
uses IPV6-ACE-GROUP {
when "../afi = 'ipv6'" ;
}
uses IPV4-ACE-GROUP {
when "../afi = 'ipv4'" ;
}
leaf global-fragments {
default "not-set";
type enumeration {
enum not-set;
enum permit-all {
description "Allow all fragments";
}
enum deny-all {
description "Drop all fragments";
}
}
description
"Optimizes fragment handling for noninitial fragments.
When this leaf is set to 'permit-all', noninitial
fragments willbe permitted unless explicitly denied.
When this leaf is set to 'deny-all', noninitial
fragments will be denied unless explicitly
permitted. ";
}
}
}
11. ACL-MAC Configuration YANG Module
This module imports type definitions from common-types YANG defined
in this model.
module acl-mac {
namespace "urn:cisco:params:xml:ns:yang:acl-mac";
// replace with IANA namespace when assigned
prefix acl-mac;
Huang & Clemm Expires March 4, 2013 [Page 67]
Internet-Draft yang-acl August 2012
import acl { prefix acl; }
import common-types {
prefix "c-types";
}
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: http://tools.ietf.org/wg/netmod/
WG List: netmod@ietf.org
WG Chair: David Kessens
david.kessens@nsn.com
WG Chair: Juergen Schoenwaelder
j.schoenwaelder@jacobs-university.de
Editor: Lisa Huang
yihuan@cisco.com
Editor: Alexander Clemm
alex@cisco.com";
description
"This YANG module augments the 'acl' module with
configuration and operational data for MAC access control list
An ACL is an ordered set of rules and actions used to
filter traffic.
Each set of rules and actions is represented as an Access
Control Entries (ACE). Each ACE is evaluated sequentially.
When the rule matches then action for that rule is applied
to the packet.
MAC ACLs - MAC ACLs are used to filter traffic using the
information in the Layer 2 header of each packet.
MAC ACLs are by default only applied to non-IP
traffic; however, Layer 2 interfaces can be configured to
apply MAC ACLs to all traffic.
Terms and Acronyms
ACE (ace): Access Control Entry
ACL (acl): Access Control List
AFI (afi): Authority and Format Identifier (Address Field
Identifier)
Huang & Clemm Expires March 4, 2013 [Page 68]
Internet-Draft yang-acl August 2012
CoS (cos): Class of Service
MAC: Media Access Control
TTL (ttl): Time to Live
VLAN (vlan): Virtual Local Area Network
VRF(vrf) : Virtual Routing and Forwarding
";
revision 2012-08-31 {
description "Initial revision. ";
}
/* Layer 2 ACL */
grouping MAC-ACE-GROUP {
description
"Layer 2 Access Control Entry (ACE). The mac-aces
container contains a list of mac-ace. Each mac-ace is
comprised of a sequence number and a choice of remark
(comment) or a rule.
A rule is referred to as 'packet-filter', although it
contains both a filter and an action.
The packet-filter requires a mandatory action (permit/deny)
and one or more options such as source-address with mask,
ethertype, vlan etc.";
container mac-aces {
list mac-ace {
key sequence-num;
leaf sequence-num {
type acl:Sequence-Number;
description
"This number determines the order in which the
ace within the access list will be evaluated.";
}
choice remark-or-ace-filter {
mandatory true;
case remark {
leaf remark {
type acl:Remark;
mandatory true;
description
"A remark is a comment that can be
inserted into an ACL in order to make
the access list easier for the network
administrator to understand.
Huang & Clemm Expires March 4, 2013 [Page 69]
Internet-Draft yang-acl August 2012
It is retained to facilitate
co-existence with CLI.";
}
}
case filter {
container filters {
uses acl:MAC-SOURCE-NETWORK;
uses acl:MAC-DESTINATION-NETWORK;
leaf ethertype {
type c-types:Ether-Type;
description "Ether-Type (also known as
protocol) in hex 0x0-0xffff";
}
leaf ethertype-mask {
when "boolean(../ethertype)";
type c-types:Ether-Type;
default "0x0000";
description
"Ether-type mask in hex 0x0-0xFFFF.
0x0 is exactly match of the
Ethertype..";
if-feature acl:ethertype-mask;
}
leaf cos {
type c-types:CoS;
description "CoS value <0-7>";
}
leaf time-range {
type acl:Time-Range-Ref;
description
"Enable packet capture on this
filter for a specify time range
by name (Max name
string size 64).";
}
leaf vlan {
type c-types:Vlan-Identifier;
description "VLAN number";
}
leaf enable-capture {
type boolean ;
description
Huang & Clemm Expires March 4, 2013 [Page 70]
Internet-Draft yang-acl August 2012
"Enable packet capture on this
filter for this session.";
}
leaf capture-session-id {
type uint8 {
range "1..48";
}
description
"Enable packet capture on this
filter for this session.";
if-feature acl:capture-session-id;
}
}
container actions {
leaf action {
type acl:ACL-Action;
mandatory true;
description "Permit/deny action.";
}
leaf log {
type boolean;
default false;
description
"Causes an informational
logging message about the
packet that matches the entry
to be sent to the console.";
}
}
leaf match {
config false;
type uint64;
description
"The total packets number that
have matched for the particular ACE";
}
}
}
}
}
}
augment "/acl:acls/acl:acl" {
when "acl:acl-type = 'mac-acl'";
uses MAC-ACE-GROUP;
}
Huang & Clemm Expires March 4, 2013 [Page 71]
Internet-Draft yang-acl August 2012
}
12. ACL-ARP Configuration YANG Module
module acl-arp {
namespace "urn:cisco:params:xml:ns:yang:acl-arp";
// replace with IANA namespace when assigned
prefix acl-arp;
import acl {
prefix acl;
}
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: http://tools.ietf.org/wg/netmod/
WG List: netmod@ietf.org
WG Chair: David Kessens
david.kessens@nsn.com
WG Chair: Juergen Schoenwaelder
j.schoenwaelder@jacobs-university.de
Editor: Lisa Huang
yihuan@cisco.com
Editor: Alexander Clemm
alex@cisco.com";
description
"This YANG module augments the 'acl' module with
configuration and operational data for ARP access control list
An ACL is an ordered set of rules and actions used to filter
traffic.
Each set of rules and actions is represented as an Access
Control Entries (ACE). Each ACE is evaluated sequentially.
When the rule matches then action for that rule is applied
to the packet.
ARP ACLs - The device applies ARP ACLs to IP traffic.
Terms and Acronyms
Huang & Clemm Expires March 4, 2013 [Page 72]
Internet-Draft yang-acl August 2012
ACE (ace): Access Control Entry
ACL (acl): Access Control List
ARP (arp): Address Resolution Protocol
IP (ip): Internet Protocol
MAC: Media Access Control
VLAN (vlan): Virtual Local Area Network
";
revision 2012-08-31 {
description "Initial revision. ";
}
grouping ARP-ACE-GROUP {
description "ARP Access Control Entry (ACE).";
container arp-aces {
list arp-ace {
key "sequence-num";
leaf sequence-num {
type acl:Sequence-Number;
mandatory true;
description
"This number determines the order in which the
statements within the access list will be
evaluated.";
}
choice remark-or-ace-filter {
case remark {
leaf remark {
mandatory true;
type acl:Remark;
description
"A remark is a comment that can be
inserted into an ACL in order to make
the access list easier for the network
administrator to understand.
It is retained to facilitate
co-existence with CLI.";
}
}
case filter {
container filters {
leaf direction {
default "bi-direction";
type enumeration {
Huang & Clemm Expires March 4, 2013 [Page 73]
Internet-Draft yang-acl August 2012
enum bi-direction;
enum request;
enum response;
}
description "ARP request/response.";
}
uses acl:IP-SOURCE-NETWORK;
uses acl:IP-DESTINATION-NETWORK {
when "../direction = 'response'";
}
uses acl:MAC-SOURCE-NETWORK;
uses acl:MAC-DESTINATION-NETWORK {
when "../direction = 'response'";
}
leaf enable-capture {
type boolean ;
description
"Enable packet capture on this
filter for this session.";
}
leaf capture-session-id {
type uint32 {
range "1..48";
}
description
"Enable packet capture on this
filter for this session.
Session ID range is 1 to 48";
}
}
container actions {
leaf action {
type acl:ACL-Action;
mandatory true;
description "Permit/deny on match";
}
leaf log {
type boolean;
default false;
description "Log on match";
}
}
leaf match {
config false;
Huang & Clemm Expires March 4, 2013 [Page 74]
Internet-Draft yang-acl August 2012
type uint64;
description
"The total packet that have matched for
the particular ACE";
}
}
}
}
}
}
augment "/acl:acls/acl:acl" {
when "acl:acl-type = 'arp-acl'";
uses ARP-ACE-GROUP;
}
}
13. COMMON-TYPES YANG Module
module common-types {
namespace "urn:cisco:params:xml:ns:yang:common-types";
// replace with IANA namespace when assigned
prefix c-types;
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: http://tools.ietf.org/wg/netmod/
WG List: netmod@ietf.org
WG Chair: David Kessens
david.kessens@nsn.com
WG Chair: Juergen Schoenwaelder
j.schoenwaelder@jacobs-university.de
Editor: Lisa Huang
yihuan@cisco.com
Editor: Alexander Clemm
alex@cisco.com";
description
"This module contains a collection of generally useful
YANG types that are required by YANG modules for the
Huang & Clemm Expires March 4, 2013 [Page 75]
Internet-Draft yang-acl August 2012
management of ACLs, yet not specific to ACLs.
Terms and Acronyms
CoS (cos): Class of Service
ICMP (icmp): Internet Control Message Protocol
IGMP (igmp): Internet Group Management Protocol
IP (ip): Internet Protocol
IPv4 (ipv4):Internet Protocol Version 4
IPv6 (ipv6): Internet Protocol Version 6
TCP (tcp): Transmission Control Protocol
ToS (tos): Type of Service
TTL (ttl): Time to Live
UDP (udp): User Datagram Protocol
VLAN (vlan): Virtual Local Area Network
";
revision 2012-08-31 {
description "Initial revision. ";
}
typedef CoS{
type uint8 {
range "0..7";
}
description
"Class of Service.
An integer that is in the range of the layer 2 CoS values.
This corresponds to the 802.1p and ISL CoS values.";
reference "IEEE 802.1p";
}
typedef ToS{
type uint8 {
range "0..15";
}
description
"ToS stands for Type of service .
The ToS field are five bits in the IPv4 header.
It could specify a datagrams priority and
Huang & Clemm Expires March 4, 2013 [Page 76]
Internet-Draft yang-acl August 2012
request a route for low-delay, high-throughput,
or highly-reliable service.
Based on these TOS values, a packet would be placed in
an prioritized outgoing queue, or take a route with
appropriate latency, throughput, or reliability.
The following are TOS field values (expressed as
binary numbers):
1000 -- minimize delay
0100 -- maximize throughput
0010 -- maximize reliability
0001 -- minimize monetary cost
0000 -- normal service
.";
reference
"RFC 791 Internet Protocol
Protocol Specification
RFC 1122 Requirements for Internet Hosts --
Communication Layers
RFC 1349 Type of Service in the Internet Protocol
Suite
RFC 2474 Definition of the Differentiated Services
Field (DS Field)
in the IPv4 and IPv6 Headers
RFC 3168 The Addition of Explicit Congestion
Notification (ECN) to IP
";
}
typedef Precedence{
type uint8 {
range "0..7";
}
description
"Indicates the IP precedence.
Precedence is three bits in IP header.
Value Description
-------------------
000 (0) Routine or Best Effort
001 (1) Priority
010 (2) Immediate
011 (3) Flash - mainly used for Voice Signaling
or for Video.
Huang & Clemm Expires March 4, 2013 [Page 77]
Internet-Draft yang-acl August 2012
100 (4) Flash Override
101 (5) Critical -mainly used for Voice RTP.
110 (6) Internet
111 (7) Network";
reference
"RFC 791 Internet Protocol Chapter 3.1
Protocol Specification";
}
typedef TCP-Flag-Type{
description "";
type bits {
bit fin {
position 0;
description "No more data from sender";
}
bit syn {
position 1;
description "Synchronize sequence numbers";
}
bit rst {
position 2;
description "Reset the connection";
}
bit psh {
position 3;
description "Push Function";
}
bit ack {
position 4;
description "Acknowledgment field significant";
}
bit urg {
position 5;
description "Urgent Pointer field significant";
}
}
reference "RFC 793 TRANSMISSION CONTROL PROTOCOL";
}
typedef Ether-Type {
type string {
pattern '0x[0-9a-fA-F]{4}';
}
description
"EtherType is 0x0-0xffff. The protocol number
is a four-byte hexadecimal number prefixed with 0x.
Huang & Clemm Expires March 4, 2013 [Page 78]
Internet-Draft yang-acl August 2012
Valid protocol numbers are from 0x0 to 0xffff.
This list shows the EtherType values and their
corresponding protocol keywords:
0x0600 xns-idp Xerox XNS IDP
0x0BAD vines-ip Banyan VINES IP
0x0baf vines-echo Banyan VINES Echo
0x6000 etype-6000 DEC unassigned, experimental
0x6001 mop-dump DEC Maintenance Operation Protocol
(MOP) Dump/Load Assistance
0x6002 mop-console DEC MOP Remote Console
0x6003 decnet-iv DEC DECnet Phase IV Route
0x6004 lat DEC Local Area Transport (LAT)
0x6005 diagnostic DEC DECnet Diagnostics
0x6007 lavc-sca DEC Local-Area VAX Cluster (LAVC), SCA
0x6008 amber DEC AMBER
0x6009 mumps DEC MUMPS
0x0800 ip Malformed, invalid, or deliberately corrupt
IP frames
0x8038 dec-spanning DEC LANBridge Management
0x8039 dsm DEC DSM/DDP
0x8040 netbios DEC PATHWORKS DECnet NETBIOS Emulation
0x8041 msdos DEC Local Area System Transport
0x8042 etype-8042 DEC unassigned
0x809B appletalk Kinetics EtherTalk (AppleTalk over
Ethernet)
0x80F3 aarp Kinetics AppleTalk Address Resolution
Protocol (AARP)
Huang & Clemm Expires March 4, 2013 [Page 79]
Internet-Draft yang-acl August 2012
bpdu-sap BPDU SAP encapsulated packets
bpdu-snap BPDU SNAP encapsulated packets
ipx-arpa IPX Advanced Research Projects Agency
(ARPA)
ipx-non-arpa IPX non arpa
lacp Link Aggregation Control Protocol(LACP)
encapsulated packets
pagp Port Aggregation Protocol(PAGP)
encapsulated packets
vtp VTP packets
";
}
typedef IP-Protocol {
type uint8{
range "0..255";
}
description
"The Internet Protocol (IP) is the principal communications
protocol used for relaying datagrams (also known as network
packets) across an internetwork using the Internet Protocol
Suite.
IP protocol number value is 0 to 255. It is an 8 bit field
in the packet header";
reference
"IANA Protocol Numbers
RFC5237 IANA Allocation Guidelines for the Protocol Field";
}
typedef IGMP-Code{
type uint8 ;
description
"Many of these IGMP types have a 'code' field. Here is
the list of the types again with their assigned
code fields.
Type Name Reference
--------- ------------------------------------ ---------
0x11 IGMP Membership Query [RFC1112]
0x12 IGMPv1 Membership Report [RFC1112]
0x13 DVMRP [RFCDVMRP]
0x14 PIM version 1 [PIMv1]
0x15 Cisco Trace Messages
0x16 IGMPv2 Membership Report [RFC2236]
0x17 IGMPv2 Leave Group [RFC2236]
Huang & Clemm Expires March 4, 2013 [Page 80]
Internet-Draft yang-acl August 2012
0x1e Multicast Traceroute Response [Fenner]
0x1f Multicast Traceroute [Fenner]
0x22 IGMPv3 Membership Report [RFC3376]
";
reference
"IANA Internet Group Management Protocol (IGMP) Type
Numbers";
}
typedef ICMP-Type {
type uint32 {
range "0..255";
}
description
"ICMP-Type is the Internet Control Message Protocol (ICMP)
'type' field.
The ICMP header starts after the IPv4 header. All ICMP
packets will have an 8-byte header and variable-sized
data section.
The first 4 bytes of the header will be consistent.
The first byte is for the ICMP type. The second byte is
for the ICMP code.
ICMP type is specified below
Type Name Reference
---- ------------------------- ---------
0 Echo Reply [RFC792]
1 Unassigned [JBP]
2 Unassigned [JBP]
3 Destination Unreachable [RFC792]
4 Source Quench [RFC792]
5 Redirect [RFC792]
6 Alternate Host Address [JBP]
7 Unassigned [JBP]
8 Echo [RFC792]
9 Router Advertisement [RFC1256]
10 Router Selection [RFC1256]
11 Time Exceeded [RFC792]
12 Parameter Problem [RFC792]
13 Timestamp [RFC792]
14 Timestamp Reply [RFC792]
15 Information Request [RFC792]
16 Information Reply [RFC792]
17 Address Mask Request [RFC950]
18 Address Mask Reply [RFC950]
19 Reserved (for Security) [Solo]
Huang & Clemm Expires March 4, 2013 [Page 81]
Internet-Draft yang-acl August 2012
20-29 Reserved (for Robustness Experiment) [ZSu]
30 Traceroute [RFC1393]
31 Datagram Conversion Error [RFC1475]
32 Mobile Host Redirect [David Johnson]
33 IPv6 Where-Are-You [Bill Simpson]
34 IPv6 I-Am-Here [Bill Simpson]
35 Mobile Registration Request [Bill Simpson]
36 Mobile Registration Reply [Bill Simpson]
37-255 Reserved [JBP]";
reference
"RFC1700 ASSIGNED NUMBERS
RFC792 Internet Control Message Protocol
RFC4443 Internet Control Message Protocol (ICMPv6)
for the Internet Protocol Version 6 (IPv6)
Specification
RFC2780 IANA Allocation Guidelines For Values In
the Internet Protocol and Related Headers";
}
typedef ICMP-Code{
type uint32 {
range "0..255";
}
description
"ICMP subtype to the given type.
The ICMP header starts after the IPv4 header. All ICMP
packets will have an 8-byte header and variable-sized
data section.
The first 4 bytes of the header will be consistent.
The first byte is for the ICMP type. The second byte
is for the ICMP code. ";
reference "RFC2 INTERNET CONTROL MESSAGE PROTOCOL";
}
typedef Vlan-Identifier {
type uint16 {
range "1 .. 4095";
}
description
"This type denotes a VLAN tag. ";
reference
"RFC3069 VLAN Aggregation for Efficient IP Address
Allocation
IEEE 802.1Q";
}
typedef Time-to-Live{
Huang & Clemm Expires March 4, 2013 [Page 82]
Internet-Draft yang-acl August 2012
description "The TTL is an 8-bit field in IP header.
The maximum TTL value is 255.";
type uint8 {
range "0..255";
}
}
}
14. Security Considerations
.
15. Acknowledgements
We wish to acknowledge the contributions of Louis Fourie and Dana
Blair to the design of this YANG data model.
16. Normative References
[RFC6020] Bjorklund, M., "YANG - A Data Modeling Language for the
Network Configuration Protocol (NETCONF)", RFC 6020,
October 2010.
[RFC6021] Schoenwaelder, J., "Common YANG Data Types", RFC 6021,
October 2010.
Authors' Addresses
Lisa Huang
Cisco Systems
EMail: yihuan@cisco.com
Alexander Clemm
Cisco Systems
EMail: alex@cisco.com
Huang & Clemm Expires March 4, 2013 [Page 83]