CoRE Working Group C. Groves
Internet-Draft W. Yang
Intended status: Standards Track Huawei
Expires: April 20, 2017 October 17, 2016
SenML Base Time Offset Attribute
draft-groves-core-senml-bto-00
Abstract
SenML [I-D.ietf-core-senml] defines a base time attribute and time
value which is used to determine the time when a value is recorded.
In some applications a SenML package will contain a series of records
related to a constant sample time interval, e.g. once every 60
seconds. This means that the time attribute will be required for
each record. This document defines a new "time offset" base
attribute that allows a sender to include the time for the sample
interval between records. If the "time offset" base attribute is
used the sender will not send the time attribute for each record,
minimising message and storage size.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 20, 2017.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Groves & Yang Expires April 20, 2017 [Page 1]
Internet-Draft SenML BTO October 2016
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. SenML Structure and Semantics . . . . . . . . . . . . . . . . 4
3.1. Base Attributes . . . . . . . . . . . . . . . . . . . . . 4
3.2. Regular Attributes . . . . . . . . . . . . . . . . . . . 4
3.3. Considerations . . . . . . . . . . . . . . . . . . . . . 4
4. JSON Representation (application/senml+json) . . . . . . . . 5
5. CBOR Representation (application/senml+cbor) . . . . . . . . 5
6. XML representation (application/senml+xml) . . . . . . . . . 5
7. EXI Representation (application/senml-exi) . . . . . . . . . 6
8. Security Considerations . . . . . . . . . . . . . . . . . . . 7
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
11. Normative References . . . . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
SenML currently defines the base time "bt" and time "t" attributes to
indicate the time that each value in a SenML record is recorded.
This means that for each record (value "v") that a "t" attribute is
required. The example from section 5.1.2/[I-D.ietf-core-senml] is
copied below to illustrate a SenML package with multiple records.
Groves & Yang Expires April 20, 2017 [Page 2]
Internet-Draft SenML BTO October 2016
[ {"bn": "urn:dev:ow:10e2073a01080063",
"bt": 1320067464,
"bu": "%RH",
"v": 21.2, "t": 0 },
{ "v": 21.3, "t": 10 },
{ "v": 21.4, "t": 20 },
{ "v": 21.4, "t": 30 },
{ "v": 21.5, "t": 40 },
{ "v": 21.5, "t": 50 },
{ "v": 21.5, "t": 60 },
{ "v": 21.6, "t": 70 },
{ "v": 21.7, "t": 80 },
{ "v": 21.5, "t": 90 },
...
Figure 1: SenML Package with multiple records
As can be seen in the example above there is a fixed offset between
the data points of 10 seconds.
This document proposes a base time offset "bto" attribute that is
used to indicate the offset between datapoints when a fixed offset is
used. This negates the need to include the "t" attribute for each
data point. The example below takes the above example and applies
the base time offset to it.
[ {"bn": "urn:dev:ow:10e2073a01080063",
"bt": 1320067464,
"bto": 10,
"bu": "%RH",
"v": 21.2},
{ "v": 21.3},
{ "v": 21.4},
{ "v": 21.4},
{ "v": 21.5},
{ "v": 21.5},
{ "v": 21.5},
{ "v": 21.6},
{ "v": 21.7},
{ "v": 21.5},
...
Figure 2: SenML Package with multiple records using base time offset
It can be seen that it results in a record and overall pack size
reduction. The receiver of the record would use the base time "bt"
for the initial data point, e.g. "v": 21.2 would have a timestamp of
Groves & Yang Expires April 20, 2017 [Page 3]
Internet-Draft SenML BTO October 2016
1320067464. Each subsequent record would have a time stamp equal to
the previous record plus the base time offset "bto", e.g. "v": 21.3
would have a timestamp of 1320067474, "v": 21.4 would have a
timestamp of 1320067484, and so on.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
See [I-D.ietf-core-senml] for further definitions.
3. SenML Structure and Semantics
3.1. Base Attributes
This document adds an additional "base time offset" attribute.
Base Time Offset: The base time offset represents a fixed time offset
between each record in a SenML pack. The first record represents
time zero (or the base time if provided) and the offset is then
applied to each subsequent record. Either a positive or negative
base time offset is allowed.
3.2. Regular Attributes
This document modifies the behaviour of the time attribute.
Time: If the base time offset attribute is used in a SenML pack then
the time attribute shall not be used in the individual records.
_Editor's note: One theoretical use case may be to include the time
attribute if the entry's time deviates from the regular offset. It
is not seen that such a corner case warrants the extra complexity._
3.3. Considerations
To simplify implementation, the use of base time offset is limited
to:
o Fixed time increasing or decreasing records from the time stamp
associated with the first record in the SenML pack. This means
that usages such as described by the 2nd example in
5.1.2/[I-D.ietf-core-senml] where negative time offset from time
zero being provided by the last record in a SenML pack are not
possible.
Groves & Yang Expires April 20, 2017 [Page 4]
Internet-Draft SenML BTO October 2016
_Editor's note: It could be possible to facilitate this use case by
allowing a t=0 to be set on the last record with the use of a
negative base time offset value. However again it's not seen that
such a corner case warrants the extra complexity in having to store
values and calculate offsets at the end of transmission/reception._
o It is not possible to for two records in the SenML pack to have
the same time. For example the inclusion of a record for a
voltage measurement followed by a current measurement would result
in the records having times with a difference of the time offset.
4. JSON Representation (application/senml+json)
This document defines an additional SenML label (JSON object member
name) as shown in Table 1 below.
+------------------+-------+-------+
| Name | label | Type |
+------------------+-------+-------+
| Base Time Offset | bto | Numer |
+------------------+-------+-------+
Table 1: JSON SenML Labels
5. CBOR Representation (application/senml+cbor)
As per section 6/[I-D.ietf-core-senml], for CBOR the string map key
"bto" shall be used to indicate the use of the base time offset.
6. XML representation (application/senml+xml)
This document defines an addition XML attribute as shown in Table 2
below.
+------------------+-----+--------+
| Name | XML | Type |
+------------------+-----+--------+
| Base Time Offset | bto | double |
+------------------+-----+--------+
Table 2: XML SenML Labels
The RelaxNG schema for the XML is:
Groves & Yang Expires April 20, 2017 [Page 5]
Internet-Draft SenML BTO October 2016
senml = element senml {
attribute bn { xsd:string }?,
attribute bt { xsd:double }?,
attribute bv { xsd:double }?,
attribute bs { xsd:double }?,
attribute bu { xsd:string }?,
attribute bver { xsd:int }?,
attribute bto { xsd:double }?,
attribute l { xsd:string }?,
attribute n { xsd:string }?,
attribute s { xsd:double }?,
attribute t { xsd:double }?,
attribute u { xsd:string }?,
attribute ut { xsd:double }?,
attribute v { xsd:double }?,
attribute vb { xsd:boolean }?,
attribute vs { xsd:string }?,
attribute vd { xsd:string }?
}
sensml =
element sensml {
senml+
}
start = sensml
7. EXI Representation (application/senml-exi)
As per clause 8/[I-D.ietf-core-senml] extensions are indicated
through the use of an EXI schemaID options. The EXI schemaID options
MUST be set to the value of "b" indicating the scheme provided in
this specification.
The following is the XSD Schema to be used for strict schema guided
EXI processing.
Groves & Yang Expires April 20, 2017 [Page 6]
Internet-Draft SenML BTO October 2016
8. Security Considerations
No extra security issues are seen beyond those described in
[I-D.ietf-core-senml].
9. IANA Considerations
This document proposes one new entry in the IANA SenML label
reegistry.
Label Name: Base Time Offset
Label: bto
Groves & Yang Expires April 20, 2017 [Page 7]
Internet-Draft SenML BTO October 2016
CBOR: -
XML Type: Double
ID: b
Reference: This specification.
10. Acknowledgements
TBD
11. Normative References
[I-D.ietf-core-senml]
Jennings, C., Shelby, Z., Arkko, J., Keranen, A., and C.
Bormann, "Media Types for Sensor Markup Language (SenML)",
draft-ietf-core-senml-03 (work in progress), October 2016.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
.
Authors' Addresses
Christian Groves
Huawei
Australia
Email: Christian.Groves@nteczone.com
Weiwei Yang
Huawei
P.R.China
Email: tommy@huawei.com
Groves & Yang Expires April 20, 2017 [Page 8]