Network Working Group X. Geng
Internet-Draft M. Chen
Intended status: Standards Track Huawei
Expires: April 24, 2019 Z. Li
China Mobile
R. Rahman
Cisco Systems
October 21, 2018

DetNet Configuration YANG Model
draft-geng-detnet-conf-yang-06

Abstract

This document defines a YANG data model for Deterministic Networking (DetNet), which includes the DetNet topology YANG module, DetNet flow configuration YANG module and DetNet Transport QoS YANG Module.

The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA).

Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 24, 2019.

Copyright Notice

Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

Deterministic Networking (DetNet) [I-D.ietf-detnet-architecture] is defined to provide high-quality network service with extremely low packet loss rate, bounded low latency and jitter.

DetNet flow information is defined in[I-D.ietf-detnet-flow-information-model], and the DetNet models are categorized as:

            User                Network Operator
                   flow/service  
           +---+      model        +---+
           |   | <---------------> | X |    management/control
           +---+                   +-+-+       plane entity
                                     ^
                                     |   configuration
                                     |      model
                              +------------+
                              v      |     |
                             +-+     |     v  network
                             +-+     v    +-+  nodes
                                    +-+   +-+
                                    +-+

                  Figure 1. Three Information Models

They are shown in the Figure 1.

This document defines DetNet configuration YANG [RFC7950] [RFC6991]data models, which include:

2. Terminologies

This documents uses the terminologies defined in [I-D.ietf-detnet-architecture].

3. DetNet Topology Model

A DetNet topology is composed of a set of DetNet nodes and DetNet links. DetNet nodes represent the network devices that can transport DetNet services, which are connected by DetNet links. A DetNet Link Terminate Point(LTP) is the connection point between a DetNet node and a DetNet link, which represents the port or interface of a network node. The concept of DetNet node/link/LTP are similar as TE node/link/LTP that are defined in [I-D.ietf-teas-yang-te-topo].

Figure 2 shows a simple DetNet topology: A is a DetNet node, B is DetNet a LTP, and C is a DetNet link.

                        +---+           +---+
                        | A |o(B)--(C)--|   |
                        +---+           +---+

                Figure 2. An example of DetNet Topology

[I-D.ietf-teas-yang-te-topo] to cover the following attributes, which are necessary for supporting DetNet congestion protection and service protection functions:

The above attributes are categorized into three types: node attributes, link attributes and LTP attributes. The detailed descriptions and model definitions are specified in section 4.1, 4.2 and 4.3, respectively.

3.1. DetNet Node Attributes

Section 4.3 of [I-D.finn-detnet-bounded-latency] gives a DetNet time model, which defines that the delay within a node includes five parts: processing delay, regulation delay, queuing delay, output delay and preemption delay. The processing delay, queuing delay and regulation delay are variable in general, but for DetNet, these delays should be bounded, which is the basic assumption of deterministic networking. These bounded delay parameters are necessary to perform DetNet path computation. Among this delay attributes, processing delay and regulation delay are node relevant, and the queuing delay is LTP relevant. In addition, in order to simplify the model and implementation, the processing delay and regulation delay are combined as processing delay, and the preemption delay is included in queuing delay. [Editor notes: more comments and inputs need here].

For the DetNet node attributes, the following variables are introduced:

augment /nw:networks/nw:network/nw:node/tet:te/tet:te-node-attributes:
   +--rw detnet-node-attributes
      +--rw minimum-packet-processing-delay?             uint32
      +--rw maximum-packet-processing-delay?             uint32
      +--rw maximum-packet-processing-delay-variation?   uint32

The modeling structure is shown below:

3.2. DetNet Link Attributes

DetNet link attributes include link delay and link bandwidth for DetNet. This document introduces the following link related attributes:

The DetNet link attributes are modeled within a link, and the YANG module structure is shown below:

augment /nw:networks/nw:network/nt:link/tet:te/tet:te-link-attributes:
   +--rw detnet-link-attributes
      +--rw maximum-reservable-bandwidth
      |  +--rw te-bandwidth
      |     +--rw (technology)?
      |        +--:(generic)
      |           +--rw generic?   te-bandwidth
      +--rw reserved-detnet-bandwidth
      |  +--rw te-bandwidth
      |     +--rw (technology)?
      |        +--:(generic)
      |           +--rw generic?   te-bandwidth
      +--rw available-detnet-bandwidth
         +--rw te-bandwidth
            +--rw (technology)?
               +--:(generic)
                  +--rw generic?   te-bandwidth

3.3. DetNet Link Terminate Point Attributes

The concept of LTP is introduced in [I-D.ietf-teas-yang-te-topo], and this section introduces attributes for DetNet LTP.

PREOF (Packet Replication/Elimination/Ordering Function) is for DetNet service protection, which includes :

The above functions are modeled as a set of capabilities and relevant parameters, which are listed below:

[I-D.finn-detnet-bounded-latency]. Queuing related attributes are listed below:

In addition, DetNet LTP also includes queuing management algorithms and queuing delay attributes. In the context of DetNet, the delay of queuing is bounded, and the bound depends on what queuing management method is used and how many buffers are allocated. More information can be found in

The DetNet LTP attributes are modeled with a LTP, the YANG module structure is shown below:

augment /nw:networks/nw:network/nw:node/nt:termination-point/tet:te:
   +--rw detnet-terminate-point-attributes
      +--rw elimination-capability?           boolean
      +--rw replication-capability?           boolean
      +--rw in-ordering-capability
      |  +--rw in-ordering-capability?         boolean
      |  +--rw maximum-out-of-order-packets?   uint32
      +--rw queuing-algorithm-capabilities
      |  +--rw credit-based-shaping?            boolean
      |  +--rw time-aware-shaping?              boolean
      |  +--rw cyclic-queuing-and-forwarding?   boolean
      |  +--rw asynchronous-traffic-shaping?    boolean
      +--rw queues* [queue-identifier]
         +--rw queue-identifier                   uint32
         +--rw queue-buffer-size?                 uint32
         +--rw enabled-queuing-algorithm
         |  +--rw credit-based-shaping?            boolean
         |  +--rw time-aware-shaping?              boolean
         |  +--rw cyclic-queuing-and-forwarding?   boolean
         |  +--rw asynchronous-traffic-shaping?    boolean
         +--rw minimum-queuing-delay?             uint32
         +--rw maximum-queuing-delay?             uint32
         +--rw maximum-queuing-delay-variation?   uint32

4. DetNet Flow Configuration Model

DetNet flow configuration includes DetNet Service Proxy configuration, DetNet Service Layer configuration and DetNet Transport Layer configuration. The corresponding attributes used in different layers are defined in Section 4.1, 4.2, 4.3, respectively. Section 4.4 gives a simple example on how to use these attributes for DetNet flow configuration.

4.1. DetNet Service Proxy Configuration Attributes

DetNet service proxy is responsible for mapping between application flows and DetNet flows at the edge node(egress/ingress node). Where the application flows can be either layer 2 or layer 3 flows. To identify a flow at the User Network Interface (UNI), as defined in [I-D.ietf-detnet-flow-information-model], the following flow attributes are introduced:

DetNet service proxy can also do flow filtering and policing at the ingress to prevent the misbehaviored flows from going into the network, which needs:

The YANG module structure is shown below:

   +--rw client-flow* [flow-id]
   |  +--rw flow-id                    uint32
   |  +--rw (flow-type)?
   |  |  +--:(l2-flow-identfication)
   |  |  |  +--rw source-mac-address?        yang:mac-address
   |  |  |  +--rw destination-mac-address?   yang:mac-address
   |  |  |  +--rw ethertype?                 eth:ethertype
   |  |  |  +--rw vlan-id?                   uint16
   |  |  |  +--rw pcp
   |  |  +--:(l3-flow-identification)
   |  |     +--rw (ip-flow-type)?
   |  |     |  +--:(ipv4)
   |  |     |  |  +--rw src-ipv4-address?          inet:ipv4-address
   |  |     |  |  +--rw dest-ipv4-address?         inet:ipv4-address
   |  |     |  |  +--rw dscp?                      uint8
   |  |     |  +--:(ipv6)
   |  |     |     +--rw src-ipv6-address?          inet:ipv6-address
   |  |     |     +--rw dest-ipv6-address?         inet:ipv6-address
   |  |     |     +--rw traffic-class?             uint8
   |  |     |     +--rw flow-label?                inet:ipv6-flow-label
   |  |     +--rw source-port?               inet:port-number
   |  |     +--rw destination-port?          inet:port-number
   |  |     +--rw protocol?                  uint8
   |  +--rw traffic-specification
   |     +--rw interval?                       uint32
   |     +--rw max-packets-per-interval?       uint32
   |     +--rw max-payload-size?               uint32
   |     +--rw average-packets-per-interval?   uint32
   |     +--rw average-payload-size?           uint32

4.2. DetNet Service Layer Configuration Attributes

DetNet service functions, e.g., DetNet tunnel initialization/termination and service protection, are provided in DetNet service layer. To support these functions, the following service attributes need to be configured:

The YANG module structure is shown below:

 |  +--rw relay-node
 |     +--rw name?           string
 |     +--rw flow-rank
 |     +--rw service-rank
 |     +--rw in-segment* [in-segment-id]
 |     |  +--rw in-segment-id        uint32
 |     |  +--rw (flow-type)?
 |     |  |  +--:(IP)
 |     |  |  |  +--rw (ip-flow-type)?
 |     |  |  |  |  +--:(ipv4)
 |     |  |  |  |  |  +--rw src-ipv4-address?    inet:ipv4-address
 |     |  |  |  |  |  +--rw dest-ipv4-address?   inet:ipv4-address
 |     |  |  |  |  |  +--rw dscp?                uint8
 |     |  |  |  |  +--:(ipv6)
 |     |  |  |  |     +--rw src-ipv6-address?    inet:ipv6-address
 |     |  |  |  |     +--rw dest-ipv6-address?   inet:ipv6-address
 |     |  |  |  |     +--rw traffic-class?       uint8
 |     |  |  |  |     +--rw flow-label?          inet:ipv6-flow-label
 |     |  |  |  +--rw source-port?         inet:port-number
 |     |  |  |  +--rw destination-port?    inet:port-number
 |     |  |  |  +--rw protocol?            uint8
 |     |  |  +--:(MPLS)
 |     |  |     +--rw service-label        uint32
 |     |  +--rw service-function?    service-function-type
 |     +--rw out-segment* [out-segment-id]
 |        +--rw out-segment-id                    uint32
 |        +--rw detnet-service-encapsulation
 |        |  +--rw service-label    uint32
 |        |  +--rw control-word     uint32
 |        +--rw detnet-transport-encapsulation
 |           +--rw (tunnel-type)?
 |           |  +--:(IPv4)
 |           |  |  +--rw ipv4-encaplustion
 |           |  |     +--rw src-ipv4-address     inet:ipv4-address
 |           |  |     +--rw dest-ipv4-address    inet:ipv4-address
 |           |  |     +--rw protocol             uint8
 |           |  |     +--rw ttl?                 uint8
 |           |  |     +--rw dscp?                uint8
 |           |  +--:(IPv6)
 |           |  |  +--rw ipv6-encaplustion
 |           |  |     +--rw src-ipv6-address     inet:ipv6-address
 |           |  |     +--rw dest-ipv6-address    inet:ipv6-address
 |           |  |     +--rw next-header          uint8
 |           |  |     +--rw traffic-class?       uint8
 |           |  |     +--rw flow-label?          inet:ipv6-flow-label
 |           |  |     +--rw hop-limit?           uint8
 |           |  +--:(MPLS)
 |           |     +--rw mpls-encaplustion
 |           |        +--rw label-operations* [label-oper-id]
 |           |           +--rw label-oper-id    uint32
 |           |           +--rw (label-actions)?
 |           |              +--:(label-push)
 |           |              |  +--rw label-push
 |           |              |     +--rw label        uint32
 |           |              |     +--rw s-bit?       boolean
 |           |              |     +--rw tc-value?    uint8
 |           |              |     +--rw ttl-value?   uint8
 |           |              +--:(label-swap)
 |           |                 +--rw label-swap
 |           |                    +--rw out-label     uint32
 |           |                    +--rw ttl-action?   ttl-action-definition
 |           +--rw interval?                       uint32
 |           +--rw max-packets-per-interval?       uint32
 |           +--rw max-payload-size?               uint32
 |           +--rw average-packets-per-interval?   uint32
 |           +--rw average-payload-size?           uint32

4.3. DetNet Transport Layer Configuration Attributes

As defined in [I-D.ietf-detnet-architecture], DetNet transport layer optionally provides congestion protection for DetNet flows over paths provided by the underlying network. Explicit route is another mechanism that is used by DetNet to avoid temporary interruptions caused by the convergence of routing or bridging protocols, and it is also implemented at the DetNet transport layer.

To support congestion protection and explicit route, the following transport layer related attributes are necessary:

The YANG module structure is shown below:

|  +--rw transit-node
|     +--rw interval?                       uint32
|     +--rw max-packets-per-interval?       uint32
|     +--rw max-payload-size?               uint32
|     +--rw average-packets-per-interval?   uint32
|     +--rw average-payload-size?           uint32

The parameters for DetNet transport QoS are defined in Section 5.

4.4. DetNet Flow Configuration Example

This section gives an example about how to implement an end-2-end DetNet service with the collaboration of DetNet proxy, service and transport layers.

     DF: DetNet Flow
     DSPI: DetNet Service Proxy Instance
     DSI: DetNet Service Instance
     DTI: DetNet Transport Instance
     Tnl: Tunnel

                |<------- End to End DetNet Service ------>|
                |          DetNet           DetNet         |
         (AC)   |        |<-Tnl->|        |<-Tnl->|        |  (AC)
    End    |    V        V   1   V        V  2/3  V        V   |    End
    System |    +--------+       +--------+       +--------+   |  System
    +---+  |    |   E1   |=======|   R1   |=======|   E2   |   |   +---+
    |   |--|----|--------|       |--------|       |--------|---|---|   |
    |CE1|  |    | DSPI 1 |       |        |       | DSPI 2 |   |   |CE2|
    |   |       |+-------+       |        |       +-------+|       |   |
    +---+       || DSI 1 |       |  DSI 2 |       | DSI 3 ||       +---+
                ||       +       | +------+       |       ||
                || +-----+       | |DTI 2 |..DF2..|       ||
                || |DTI 1|..DF1..| +------+       |       ||
                || +-----+       | |DTI 3 |..DF3..|       ||
                |+-------+       | +------+       +-------+|
                +--------+=======+--------+=======+--------+
                 Edge Node          Relay Node       Edge Node
                    |                                   |
                    |<-------- DetNet Service --------->|

            Figure 3. End-to-end DetNet Flow Configuration

To simplify the explanation, several terms are introduced. This document defines DetNet Service Proxy Instance (DSPI), DetNet Service Instance (DSI) and DetNet Transport Instance for end-to-end DetNet flow configuration as showed in Figure 4. DSPI 1 at Edge Node 1 (E1) maps an application flow to a DetNet Flow (DF1), which is transmitted over a DetNet tunnel (Tn1). In DSI 2 of Relay Node 1 (R1), DetNet Flow 1(DF1) was replicated into two member flows: DetNet Flow 2 (DF2) transmitted by DetNet Tunnel 2 (Tnl2) and DetNet Flow 3 (DF3) by DetNet Tunnel 3(Tnl3). In DSPI 3 of Edge Node 2 (E2), DetNet Flow 2 (DF2) and DetNet Flow 3(DF3) were merged and mapped to application flow used by CE2.

5. DetNet Transport QoS Model

The YANG data model of transport QoS is very important to achieve end-to-end bounded latency and zero congestion loss. There are three possible methods to deal with the DetNet transport QoS YANG:

1. DetNet service is not aware of any QoS/queuing/bounded-latency information, and all relative parameters are defined in separate YANG models;

2. DetNet service is not aware of any of Qos/queuing/bounded-latency information, but it should maintain an interface to the corresponding YANG models;

3. DetNet service should be aware of the Qos/queuing/bounded-latency information, because some Qos/queuing/bounded-latency mechanisms are required to be configured with flow information;

How to define transport QoS YANG is still under discussion and the transport QoS YANG model is not included in the current version of the draft.

[Editor notes: more comments and inputs need here].

6. DetNet Yang Structure

6.1. DetNet Topology Model Tree Diagram

module: ietf-detnet-topology
augment /nw:networks/nw:network/nw:network-types/tet:te-topology:
   +--rw detnet-topology!
augment /nw:networks/nw:network/nw:node/tet:te/tet:te-node-attributes:
   +--rw detnet-node-attributes
      +--rw minimum-packet-processing-delay?             uint32
      +--rw maximum-packet-processing-delay?             uint32
      +--rw maximum-packet-processing-delay-variation?   uint32
augment /nw:networks/nw:network/nt:link/tet:te/tet:te-link-attributes:
   +--rw detnet-link-attributes
      +--rw maximum-reservable-bandwidth
      |  +--rw te-bandwidth
      |     +--rw (technology)?
      |        +--:(generic)
      |           +--rw generic?   te-bandwidth
      +--rw reserved-detnet-bandwidth
      |  +--rw te-bandwidth
      |     +--rw (technology)?
      |        +--:(generic)
      |           +--rw generic?   te-bandwidth
      +--rw available-detnet-bandwidth
         +--rw te-bandwidth
            +--rw (technology)?
               +--:(generic)
                  +--rw generic?   te-bandwidth
augment /nw:networks/nw:network/nw:node/nt:termination-point/tet:te:
   +--rw detnet-terminate-point-attributes
      +--rw elimination-capability?           boolean
      +--rw replication-capability?           boolean
      +--rw in-ordering-capability
      |  +--rw in-ordering-capability?         boolean
      |  +--rw maximum-out-of-order-packets?   uint32
      +--rw queuing-algorithm-capabilities
      |  +--rw credit-based-shaping?            boolean
      |  +--rw time-aware-shaping?              boolean
      |  +--rw cyclic-queuing-and-forwarding?   boolean
      |  +--rw asynchronous-traffic-shaping?    boolean
      +--rw queues* [queue-identifier]
         +--rw queue-identifier                   uint32
         +--rw queue-buffer-size?                 uint32
         +--rw enabled-queuing-algorithm
         |  +--rw credit-based-shaping?            boolean
         |  +--rw time-aware-shaping?              boolean
         |  +--rw cyclic-queuing-and-forwarding?   boolean
         |  +--rw asynchronous-traffic-shaping?    boolean
         +--rw minimum-queuing-delay?             uint32
         +--rw maximum-queuing-delay?             uint32
         +--rw maximum-queuing-delay-variation?   uint32

6.2. DetNet Flow Configuration Model Tree Diagram

module: ietf-detnet-flow-config
   +--rw detnet-flow
      +--rw (detnet-node-role)?
         +--:(transit-node)
|  +--rw transit-node
|     +--rw interval?                       uint32
|     +--rw max-packets-per-interval?       uint32
|     +--rw max-payload-size?               uint32
|     +--rw average-packets-per-interval?   uint32
|     +--rw average-payload-size?           uint32
         +--:(relay-node)
 |  +--rw relay-node
 |     +--rw name?           string
 |     +--rw flow-rank
 |     +--rw service-rank
 |     +--rw in-segment* [in-segment-id]
 |     |  +--rw in-segment-id        uint32
 |     |  +--rw (flow-type)?
 |     |  |  +--:(IP)
 |     |  |  |  +--rw (ip-flow-type)?
 |     |  |  |  |  +--:(ipv4)
 |     |  |  |  |  |  +--rw src-ipv4-address?    inet:ipv4-address
 |     |  |  |  |  |  +--rw dest-ipv4-address?   inet:ipv4-address
 |     |  |  |  |  |  +--rw dscp?                uint8
 |     |  |  |  |  +--:(ipv6)
 |     |  |  |  |     +--rw src-ipv6-address?    inet:ipv6-address
 |     |  |  |  |     +--rw dest-ipv6-address?   inet:ipv6-address
 |     |  |  |  |     +--rw traffic-class?       uint8
 |     |  |  |  |     +--rw flow-label?          inet:ipv6-flow-label
 |     |  |  |  +--rw source-port?         inet:port-number
 |     |  |  |  +--rw destination-port?    inet:port-number
 |     |  |  |  +--rw protocol?            uint8
 |     |  |  +--:(MPLS)
 |     |  |     +--rw service-label        uint32
 |     |  +--rw service-function?    service-function-type
 |     +--rw out-segment* [out-segment-id]
 |        +--rw out-segment-id                    uint32
 |        +--rw detnet-service-encapsulation
 |        |  +--rw service-label    uint32
 |        |  +--rw control-word     uint32
 |        +--rw detnet-transport-encapsulation
 |           +--rw (tunnel-type)?
 |           |  +--:(IPv4)
 |           |  |  +--rw ipv4-encaplustion
 |           |  |     +--rw src-ipv4-address     inet:ipv4-address
 |           |  |     +--rw dest-ipv4-address    inet:ipv4-address
 |           |  |     +--rw protocol             uint8
 |           |  |     +--rw ttl?                 uint8
 |           |  |     +--rw dscp?                uint8
 |           |  +--:(IPv6)
 |           |  |  +--rw ipv6-encaplustion
 |           |  |     +--rw src-ipv6-address     inet:ipv6-address
 |           |  |     +--rw dest-ipv6-address    inet:ipv6-address
 |           |  |     +--rw next-header          uint8
 |           |  |     +--rw traffic-class?       uint8
 |           |  |     +--rw flow-label?          inet:ipv6-flow-label
 |           |  |     +--rw hop-limit?           uint8
 |           |  +--:(MPLS)
 |           |     +--rw mpls-encaplustion
 |           |        +--rw label-operations* [label-oper-id]
 |           |           +--rw label-oper-id    uint32
 |           |           +--rw (label-actions)?
 |           |              +--:(label-push)
 |           |              |  +--rw label-push
 |           |              |     +--rw label        uint32
 |           |              |     +--rw s-bit?       boolean
 |           |              |     +--rw tc-value?    uint8
 |           |              |     +--rw ttl-value?   uint8
 |           |              +--:(label-swap)
 |           |                 +--rw label-swap
 |           |                    +--rw out-label     uint32
 |           |                    +--rw ttl-action?   ttl-action-definition
 |           +--rw interval?                       uint32
 |           +--rw max-packets-per-interval?       uint32
 |           +--rw max-payload-size?               uint32
 |           +--rw average-packets-per-interval?   uint32
 |           +--rw average-payload-size?           uint32
         +--:(edge-node)
         |  +--rw edge-node
         |     +--rw client-flow* [flow-id]
         |     |  +--rw flow-id                    uint32
         |     |  +--rw (flow-type)?
         |     |  |  +--:(l2-flow-identfication)
         |     |  |  |  +--rw source-mac-address?        yang:mac-address
         |     |  |  |  +--rw destination-mac-address?   yang:mac-address
         |     |  |  |  +--rw ethertype?                 eth:ethertype
         |     |  |  |  +--rw vlan-id?                   uint16
         |     |  |  |  +--rw pcp
         |     |  |  +--:(l3-flow-identification)
         |     |  |     +--rw (ip-flow-type)?
         |     |  |     |  +--:(ipv4)
         |     |  |     |  |  +--rw src-ipv4-address?          inet:ipv4-address
         |     |  |     |  |  +--rw dest-ipv4-address?         inet:ipv4-address
         |     |  |     |  |  +--rw dscp?                      uint8
         |     |  |     |  +--:(ipv6)
         |     |  |     |     +--rw src-ipv6-address?          inet:ipv6-address
         |     |  |     |     +--rw dest-ipv6-address?         inet:ipv6-address
         |     |  |     |     +--rw traffic-class?             uint8
         |     |  |     |     +--rw flow-label?                inet:ipv6-flow-label
         |     |  |     +--rw source-port?               inet:port-number
         |     |  |     +--rw destination-port?          inet:port-number
         |     |  |     +--rw protocol?                  uint8
         |     |  +--rw traffic-specification
         |     |     +--rw interval?                       uint32
         |     |     +--rw max-packets-per-interval?       uint32
         |     |     +--rw max-payload-size?               uint32
         |     |     +--rw average-packets-per-interval?   uint32
         |     |     +--rw average-payload-size?           uint32
         |     +--rw detnet-service-instance
         |        +--rw name?           string
         |        +--rw flow-rank
         |        +--rw service-rank
         |        +--rw in-segment* [in-segment-id]
         |        |  +--rw in-segment-id        uint32
         |        |  +--rw (flow-type)?
         |        |  |  +--:(IP)
         |        |  |  |  +--rw (ip-flow-type)?
         |        |  |  |  |  +--:(ipv4)
         |        |  |  |  |  |  +--rw src-ipv4-address?    inet:ipv4-address
         |        |  |  |  |  |  +--rw dest-ipv4-address?   inet:ipv4-address
         |        |  |  |  |  |  +--rw dscp?                uint8
         |        |  |  |  |  +--:(ipv6)
         |        |  |  |  |     +--rw src-ipv6-address?    inet:ipv6-address
         |        |  |  |  |     +--rw dest-ipv6-address?   inet:ipv6-address
         |        |  |  |  |     +--rw traffic-class?       uint8
         |        |  |  |  |     +--rw flow-label?          inet:ipv6-flow-label
         |        |  |  |  +--rw source-port?         inet:port-number
         |        |  |  |  +--rw destination-port?    inet:port-number
         |        |  |  |  +--rw protocol?            uint8
         |        |  |  +--:(MPLS)
         |        |  |     +--rw service-label        uint32
         |        |  +--rw service-function?    service-function-type
         |        +--rw out-segment* [out-segment-id]
         |           +--rw out-segment-id                    uint32
         |           +--rw detnet-service-encapsulation
         |           |  +--rw service-label    uint32
         |           |  +--rw control-word     uint32
         |           +--rw detnet-transport-encapsulation
         |              +--rw (tunnel-type)?
         |              |  +--:(IPv4)
         |              |  |  +--rw ipv4-encaplustion
         |              |  |     +--rw src-ipv4-address     inet:ipv4-address
         |              |  |     +--rw dest-ipv4-address    inet:ipv4-address
         |              |  |     +--rw protocol             uint8
         |              |  |     +--rw ttl?                 uint8
         |              |  |     +--rw dscp?                uint8
         |              |  +--:(IPv6)
         |              |  |  +--rw ipv6-encaplustion
         |              |  |     +--rw src-ipv6-address     inet:ipv6-address
         |              |  |     +--rw dest-ipv6-address    inet:ipv6-address
         |              |  |     +--rw next-header          uint8
         |              |  |     +--rw traffic-class?       uint8
         |              |  |     +--rw flow-label?          inet:ipv6-flow-label
         |              |  |     +--rw hop-limit?           uint8
         |              |  +--:(MPLS)
         |              |     +--rw mpls-encaplustion
         |              |        +--rw label-operations* [label-oper-id]
         |              |           +--rw label-oper-id    uint32
         |              |           +--rw (label-actions)?
         |              |              +--:(label-push)
         |              |              |  +--rw label-push
         |              |              |     +--rw label        uint32
         |              |              |     +--rw s-bit?       boolean
         |              |              |     +--rw tc-value?    uint8
         |              |              |     +--rw ttl-value?   uint8
         |              |              +--:(label-swap)
         |              |                 +--rw label-swap
         |              |                    +--rw out-label     uint32
         |              |                    +--rw ttl-action?   ttl-action-definition
         |              +--rw interval?                       uint32
         |              +--rw max-packets-per-interval?       uint32
         |              +--rw max-payload-size?               uint32
         |              +--rw average-packets-per-interval?   uint32
         |              +--rw average-payload-size?           uint32
         +--:(end-station)
+--rw end-station
   +--rw client-flow* [flow-id]
   |  +--rw flow-id                    uint32
   |  +--rw (flow-type)?
   |  |  +--:(l2-flow-identfication)
   |  |  |  +--rw source-mac-address?        yang:mac-address
   |  |  |  +--rw destination-mac-address?   yang:mac-address
   |  |  |  +--rw ethertype?                 eth:ethertype
   |  |  |  +--rw vlan-id?                   uint16
   |  |  |  +--rw pcp
   |  |  +--:(l3-flow-identification)
   |  |     +--rw (ip-flow-type)?
   |  |     |  +--:(ipv4)
   |  |     |  |  +--rw src-ipv4-address?          inet:ipv4-address
   |  |     |  |  +--rw dest-ipv4-address?         inet:ipv4-address
   |  |     |  |  +--rw dscp?                      uint8
   |  |     |  +--:(ipv6)
   |  |     |     +--rw src-ipv6-address?          inet:ipv6-address
   |  |     |     +--rw dest-ipv6-address?         inet:ipv6-address
   |  |     |     +--rw traffic-class?             uint8
   |  |     |     +--rw flow-label?                inet:ipv6-flow-label
   |  |     +--rw source-port?               inet:port-number
   |  |     +--rw destination-port?          inet:port-number
   |  |     +--rw protocol?                  uint8
   |  +--rw traffic-specification
   |     +--rw interval?                       uint32
   |     +--rw max-packets-per-interval?       uint32
   |     +--rw max-payload-size?               uint32
   |     +--rw average-packets-per-interval?   uint32
   |     +--rw average-payload-size?           uint32
   +--rw detnet-service-instance
                  +--rw name?           string
                  +--rw flow-rank
                  +--rw service-rank
                  +--rw in-segment* [in-segment-id]
                  |  +--rw in-segment-id        uint32
                  |  +--rw (flow-type)?
                  |  |  +--:(IP)
                  |  |  |  +--rw (ip-flow-type)?
                  |  |  |  |  +--:(ipv4)
                  |  |  |  |  |  +--rw src-ipv4-address?    inet:ipv4-address
                  |  |  |  |  |  +--rw dest-ipv4-address?   inet:ipv4-address
                  |  |  |  |  |  +--rw dscp?                uint8
                  |  |  |  |  +--:(ipv6)
                  |  |  |  |     +--rw src-ipv6-address?    inet:ipv6-address
                  |  |  |  |     +--rw dest-ipv6-address?   inet:ipv6-address
                  |  |  |  |     +--rw traffic-class?       uint8
                  |  |  |  |     +--rw flow-label?          inet:ipv6-flow-label
                  |  |  |  +--rw source-port?         inet:port-number
                  |  |  |  +--rw destination-port?    inet:port-number
                  |  |  |  +--rw protocol?            uint8
                  |  |  +--:(MPLS)
                  |  |     +--rw service-label        uint32
                  |  +--rw service-function?    service-function-type
                  +--rw out-segment* [out-segment-id]
                     +--rw out-segment-id                    uint32
                     +--rw detnet-service-encapsulation
                     |  +--rw service-label    uint32
                     |  +--rw control-word     uint32
                     +--rw detnet-transport-encapsulation
                        +--rw (tunnel-type)?
                        |  +--:(IPv4)
                        |  |  +--rw ipv4-encaplustion
                        |  |     +--rw src-ipv4-address     inet:ipv4-address
                        |  |     +--rw dest-ipv4-address    inet:ipv4-address
                        |  |     +--rw protocol             uint8
                        |  |     +--rw ttl?                 uint8
                        |  |     +--rw dscp?                uint8
                        |  +--:(IPv6)
                        |  |  +--rw ipv6-encaplustion
                        |  |     +--rw src-ipv6-address     inet:ipv6-address
                        |  |     +--rw dest-ipv6-address    inet:ipv6-address
                        |  |     +--rw next-header          uint8
                        |  |     +--rw traffic-class?       uint8
                        |  |     +--rw flow-label?          inet:ipv6-flow-label
                        |  |     +--rw hop-limit?           uint8
                        |  +--:(MPLS)
                        |     +--rw mpls-encaplustion
                        |        +--rw label-operations* [label-oper-id]
                        |           +--rw label-oper-id    uint32
                        |           +--rw (label-actions)?
                        |              +--:(label-push)
                        |              |  +--rw label-push
                        |              |     +--rw label        uint32
                        |              |     +--rw s-bit?       boolean
                        |              |     +--rw tc-value?    uint8
                        |              |     +--rw ttl-value?   uint8
                        |              +--:(label-swap)
                        |                 +--rw label-swap
                        |                    +--rw out-label     uint32
                        |                    +--rw ttl-action?   ttl-action-definition
                        +--rw interval?                       uint32
                        +--rw max-packets-per-interval?       uint32
                        +--rw max-payload-size?               uint32
                        +--rw average-packets-per-interval?   uint32
                        +--rw average-payload-size?           uint32

7. DetNet YANG Model

7.1. DetNet Topology YANG Model

<CODE BEGINS> file "ietf-detnet-topology@20180910.yang"
  module ietf-detnet-topology {  
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-detnet-topology";
  prefix "detnet-topology";
   
  import ietf-te-types {
    prefix "te-types";
  }

  import ietf-te-topology {
    prefix "tet";
  }

  import ietf-network {
    prefix "nw";
  }
  
  import ietf-network-topology {
    prefix "nt";
  }

  organization 
    "IETF Deterministic Networking(DetNet)Working Group";

  contact
   "WG Web:   <http://tools.ietf.org/wg/detnet/>
    WG List:  <mailto:detnet@ietf.org>

    WG Chair: Lou Berger
              <mailto:lberger@labn.net>
      
              Janos Farkas
              <janos.farkas@ericsson.com>

    Editor:   Xuesong Geng
              <mailto:gengxuesong@huawei.com>

    Editor:   Mach Chen
              <mailto:mach.chen@huawei.com>
      
    Editor:   Zhenqiang Li
              <lizhenqiang@chinamobile.com>
      
    Editor:   Reshad Rahman
              <rrahman@cisco.com>";

  description
    "This YANG module augments the 'ietf-te-topology'
     module with DetNet related capabilities and 
     parameters.";
 
    revision "2018-09-10" {
      description "Initial revision";
      reference "RFC XXXX: draft-geng-detnet-config-yang-05";
    }


  grouping detnet-queuing-algorithms {
    description
      "Relationship with IEEE 802.1 TSN YANG models is TBD.";
  }

  grouping detnet-node-attributes{
    description 
      "DetNet node related attributes.";
    leaf minimum-packet-processing-delay{
      type uint32;
      description
        "Minimum packet processing delay
         in a node. The unit of the delay
         is microsecond(us)";
    }
    leaf maximum-packet-processing-delay{
      type uint32;
      description
        "Maximum packet processing delay
         in a node. The unit of the delay
         is microsecond(us)";
    }
    leaf maximum-packet-processing-delay-variation{
      type uint32;
      description
        "Maximum packet processing delay 
         variation in a node. The unit of
         the delay variation is microsecond(us)";
    }    
  }
  
  grouping detnet-link-attributes{
    description 
      "DetNet link related attributes.";
  
    container maximum-reservable-bandwidth{
      uses te-types:te-bandwidth; 
      description
        "This container specifies the maximum bandwidth 
         that is reserved for DetNet on this link.";
    }
    
    container reserved-detnet-bandwidth{
      uses te-types:te-bandwidth;
      description
        "This container specifies the bandwidth that has 
         been reserved for DetNet on this link.";
    }
    container available-detnet-bandwidth{
      uses te-types:te-bandwidth;
      description
        "This container specifies the bandwidth that is  
         available for new DetNet flows on this link.";
    }
  }
  
  grouping detnet-terminate-point-attributes{
    description 
      "DetNet terminate point related attributes.";
    
    leaf elimination-capability{
      type boolean;
      description 
        "Indicates whether a node is able to do packet 
         elimination.";
      reference
        "Section 3.2.2.3 of
         draft-ietf-detnet-architecture";
       
    }
    leaf replication-capability{
      type boolean;
      description 
        "Indicates whether a node is able to do packet 
         replication.";
      reference
        "Section 3.2.2.2 of
         draft-ietf-detnet-architecture";
    }
    container in-ordering-capability {
      description
        "Indicates the parameters needed for
         packet in-ordering.";
      reference
        "Section 3.2.2.1 of  
         draft-ietf-detnet-architecture";
      
      leaf in-ordering-capability {
        type boolean;
      description
        "Indicates whether a node is able to do packet 
         in-ordering.";
      }
      leaf maximum-out-of-order-packets {
      type uint32;
      description
        "The maximum number of out-of-order packets.";
      }
    }
    
    container queuing-algorithm-capabilities {
      description
        "All queuing algorithms that a LTP supports.";
      uses detnet-queuing-algorithms;
    }    
    
    list queues {
      key "queue-identifier";
      description
        "A list of DetNet queues.";     
      leaf queue-identifier {
        type uint32;
        description
          "The identifier of the queue.";
      }      
      leaf queue-buffer-size {
        type uint32;
        description
          "The size of the queue with unit of bytes.";
      }
      
      container enabled-queuing-algorithm {
        description
          "The queuing algorithms that are enabled on the queue.";
           uses detnet-queuing-algorithms;
      }
      
      leaf minimum-queuing-delay{
        type uint32;
        description
          "The minimum queuing delay of the queue.
           The unit of the delay is microsecond(us)";
      }
      leaf maximum-queuing-delay{
        type uint32;
        description
          "The maximum queuing delay of the queue.
           The unit of the delay is microsecond(us)";
      }
      leaf maximum-queuing-delay-variation{
        type uint32;
        description
          "The maximum queuing delay variation of the queue.
           The unit of the delay variation is microsecond(us)";
      }  
    }  
  }
    
   augment "/nw:networks/nw:network/nw:network-types/tet:te-topology"{
    description
      "Introduce new network type for TE topology.";
    container detnet-topology {
      presence "Indicates DetNet topology.";
      description
        "Its presence identifies the DetNet topology type";
    }
  }
  
  augment "/nw:networks/nw:network/nw:node/tet:te/"
          + "tet:te-node-attributes" {
      when "../../../nw:network-types/tet:te-topology/"
      + "detnet-topology:detnet-topology" {
        description
          "Augmentation parameters apply only for networks with
           DetNet topology type.";
      }
    description 
      "Augmentation parameters apply for DetNet node attributes.";
    container detnet-node-attributes {
      description 
        "Attributes for DetNet node.";
      uses detnet-node-attributes;     
    }
  }
  
  augment "/nw:networks/nw:network/nt:link/tet:te/"
            + "tet:te-link-attributes" {
    when "../../../nw:network-types/tet:te-topology/"
         + "detnet-topology:detnet-topology" {
      description
        "Augmentation parameters apply only for networks with
        DetNet topology type.";
    }
    description 
      "Augmentation parameters apply for DetNet link attributes.";
    container detnet-link-attributes {
      description 
        "Attributes for DetNet link.";
      uses detnet-link-attributes;
    }
  }
  
  augment "/nw:networks/nw:network/nw:node/nt:termination-point/"
             + "tet:te" {
      when "../../../nw:network-types/tet:te-topology/"
            + "detnet-topology:detnet-topology" {
        description
          "Augmentation parameters apply only for networks with
           DetNet topology type.";
      }
    description 
      "Augmentation parameters apply for DetNet
       link termination point.";
    container detnet-terminate-point-attributes {
      description 
        "Attributes for DetNet link terminate point.";
      uses detnet-terminate-point-attributes;  
    }
  }
 } //topology module


<CODE ENDS>

7.2. DetNet Flow Configuration YANG Model

<CODE BEGINS> file "ietf-detnet-flow@20180910.yang"
module ietf-detnet-flow-config {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-detnet-flow-config";  
  prefix "detnet-flow";

  import ietf-yang-types {
    prefix "yang";
  }

  import ietf-inet-types{
    prefix "inet";
  }

  import ietf-ethertypes {
    prefix "eth";
  }

  organization "IETF DetNet Working Group";

  contact
    "WG Web:   <http://tools.ietf.org/wg/detnet/>
     WG List:  <mailto: detnet@ietf.org>
     WG Chair: Lou Berger
               <mailto:lberger@labn.net>
       
               Janos Farkas
               <janos.farkas@ericsson.com>
     
     Editor:   Xuesong Geng
               <mailto:gengxuesong@huawei.com>
     
     Editor:   Mach Chen
               <mailto:mach.chen@huawei.com>
     
     Editor:   Zhenqiang Li
               <lizhenqiang@chinamobile.com>
       
     Editor:   Reshad Rahman
               <rrahman@cisco.com>";
  description
    "This YANG module describes the parameters needed 
     for DetNet flow configuration and flow status
   reporting.";
  
  revision "2018-09-10" {
    description "initial revision";
    reference "RFC XXXX: draft-geng-detnet-config-yang-05";
  }

  identity detnet-node-role {
    description
      "base detnet-node-role";
  }
  
  identity end-station {
    base detnet-node-role;
    description
      "Commonly called a 'host' in IETF documents, 
       and an 'end station' is IEEE 802 documents.
       End systems of interest to this document 
       are either sources or destinations of DetNet
       flows.  And end system may or may not be 
       DetNet transport layer aware or DetNet 
       service layer aware.";
  }
  
  identity edge-node {
    base detnet-node-role;
    description
      "An instance of a DetNet relay node that
       includes either a DetNet service layer proxy
       function for DetNet service protection (e.g.
       the addition or removal of packet sequencing
       information) for one or more end systems, or
       starts or terminate congestion protection at
       the DetNet transport layer,analogous to a
       Label Edge Router (LER).";
  }

  identity relay-node {
    base detnet-node-role;
    description
      "A DetNet node including a service layer
       function that interconnects different DetNet
       transport layer paths to provide service
       protection. A DetNet relay node can be a bridge,
       a router, a firewall, or any other system that
       participates in the DetNet service layer. It
       typically incorporates DetNet transport layer
       functions as well, in which case it is
       collocated with a transit node.";
  }

  identity transit-node {
    base detnet-node-role;
    description
      "A node operating at the DetNet transport layer,
       that utilizes link layer and/or network layer
       switching across multiple links and/or
       sub-networks to provide paths for DetNet
       service layer functions. Optionally provides
       congestion protection over those paths. An MPLS
       LSR is an example of a DetNet transit node.";
  }

  identity ttl-action {
    description
      "Base identity from which all TTL 
       actions are derived.";
  }

  identity no-action {
    base "ttl-action";
    description
      "Do nothing regarding the TTL.";
  }

  identity copy-to-inner {
    base "ttl-action";
    description
      "Copy the TTL of the outer header
       to the inner header.";
  }

  identity decrease-and-copy-to-inner {
    base "ttl-action";
    description
      "Decrease TTL by one and copy the TTL 
       to the inner header.";
  }

  typedef ttl-action-definition {
    type identityref {
      base "ttl-action";
    }
    description
      "TTL action definition.";
  }

  identity detnet-transport-layer {
    description
      "The layer that optionally provides congestion 
       protection for DetNet flows over paths provided 
       by the underlying network.";
  }

  identity detnet-service-layer {
    description
      "The layer at which service protection is 
       provided, either packet sequencing, replication, 
       and elimination or packet encoding";
  }

  typedef service-function-type {
    type enumeration {
      enum replication {
        description
          "A Packet Replication Function (PRF) replicates 
           DetNet flow packets and forwards them to one or 
           more next hops in the DetNet domain.  The number 
           of packet copies sent to each next hop is a 
           DetNet flow specific parameter at the node doing 
           the replication.  PRF can be implemented by an 
           edge node, a relay node, or an end system";
      }
      enum elimination {
        description
          "A Packet Elimination Function (PEF) eliminates
           duplicate copies of packets to prevent excess 
           packets flooding the network or duplicate 
           packets being sent out of the DetNet domain. 
           PEF can be implemented by an edge node, a relay
           node, or an end system.";
      }
      enum ordering {
        description
          "A Packet Ordering Function (POF) re-orders 
           packets within a DetNet flow that are received 
           out of order.  This function can be implemented 
           by an edge node, a relay node, or an end system.";
      }
      enum elimination-ordering {
        description
          "A combination of PEF and POF that can be
           implemented by an edge node, a relay node, or 
           an end system.";
      }
      enum elimination-replication {
        description
          "A combination of PEF and PRF that can be 
           implemented by an edge node, a relay node, or 
           an end system";
      }
      enum elimination-ordering-replicaiton {
        description
          "A combination of PEF, POF and PRF that can be 
           implemented by an edge node, a relay node, or 
           an end system";
      }
    }
    description
      "DetNet service function and function combination
       types.";
  }

  grouping detnet-transport-qos {
    description
      "DetNet transport tunnel QoS attributes.";
    uses traffic-specification;
  }
  
  grouping ipv4-header {
    description
      "The IPv4 header encapsulation information.";
    leaf src-ipv4-address {
      type inet:ipv4-address;
      mandatory true;
      description
        "The source IP address of the header.";
    }
    leaf dest-ipv4-address {
      type inet:ipv4-address;
      mandatory true;
      description
        "The destination IP address of the header.";
    }
    leaf protocol {
      type uint8;
      mandatory true;
      description
        "The protocol id of the header.";
    }
    leaf ttl {
      type uint8;
      description
        "The TTL of the header.";
    }
    leaf dscp {
      type uint8;
      description
        "The DSCP field of the header.";
    }
  }

  grouping ipv6-header {
    description
      "The IPv6 header encapsulation information.";
    leaf src-ipv6-address {
      type inet:ipv6-address;
      mandatory true;
      description
        "The source IP address of the header.";
    }
    leaf dest-ipv6-address {
      type inet:ipv6-address;
      mandatory true;
      description
        "The destination IP address of the header.";
    }
    leaf next-header {
      type uint8;
      mandatory true;
      description
        "The next header of the IPv6 header.";
    }
    leaf traffic-class {
      type uint8;
      description
        "The traffic class value of the header.";
    }
    leaf flow-label {
      type inet:ipv6-flow-label;
      description
        "The flow label of the header.";
    }
    leaf hop-limit {
      type uint8 {
        range "1..255";
      }
      description
        "The hop limit of the header.";
    }
  }

  grouping mpls-header {
    description
      "The MPLS encapsulation header information.";
    list label-operations {
      key "label-oper-id";
      description
        "Label operations.";
      leaf label-oper-id {
        type uint32;
        description
          "An optional identifier that points 
           to a label operation.";
      }
      choice label-actions {
        description
          "Label action options.";
        case label-push {
          container label-push {
            description
              "Label push operation.";
            leaf label {
              type uint32;
              mandatory true;
              description
                "The label to be pushed.";
            }
            leaf s-bit {
              type boolean;
              description
                "The s-bit of the label to be pushed.";
            }
            leaf tc-value {
              type uint8;
              description
                "The traffic class value of the label 
                 to be pushed.";
            }
            leaf ttl-value {
              type uint8;
              description
                "The TTL value of the label to be 
                 pushed.";
            }
          }
        }
        case label-swap {
          container label-swap {
            description
              "Label swap operation.";
            leaf out-label {
              type uint32;
              mandatory true;
              description
                "The out MPLS label.";
            }
            leaf ttl-action {
              type ttl-action-definition;
              description
                "The label ttl actions:
                 - No-action, or 
                 - Copy to inner label,or
                 - Decrease (the in label) by 1 and
                   copy to the out label.";
            }
          }
        }
      }
    }
  }

  grouping mpls-detnet-header {
    description
        "The MPLS DetNet encapsulation header information.";
    leaf service-label {
      type uint32;
        mandatory true;
        description
          "The service label.";
    }
    leaf control-word {
      type uint32;
      mandatory true;
      description
        "The control word of the DetNet header.";
    }
  }

  grouping transport-tunnel-encap{ 
    description
      "Defines the transport tunnel encapsulation
       header.";
    choice tunnel-type {
      description
      "Tunnel type includes: IPv4, IPv6, MPLS.";
      case IPv4 {
        description
          "IPv4 tunnel.";
        container ipv4-encapsulation {
          description
            "IPv4 encapsulation.";
          uses ipv4-header;
        }
      }
      case IPv6 {
        description
          "IPv6 tunnel.";
        container ipv6-encapsulation {
          description
            "IPv6 encapsulation.";
          uses ipv6-header;
        }
      }
      case MPLS {
        description
          "MPLS tunnel.";
        container mpls-encapsulation {
          description
            "MPLS encapsulation.";
          uses mpls-header;
        }
      }
    }
  }
  
  grouping detnet-transport-instance { 
    description
      "An instance of the DetNet transport layer, which
       depends on the specific data plane that is used
       as the underlay tunnel.";    
    uses transport-tunnel-encap;    
    uses detnet-transport-qos;
  }

  grouping ip-flow-identification {
    description
        "IP flow identification.";
    choice ip-flow-type {
      description
        "IP flow types: IPv4, IPv6.";
      case ipv4 {
        description
          "IPv4 flow identification.";
        leaf src-ipv4-address {
          type inet:ipv4-address;
          description
            "The source IP address of the header.";
        }
        leaf dest-ipv4-address {
          type inet:ipv4-address;
          description
            "The destination IP address of the header.";
        }
        leaf dscp {
          type uint8;
          description
            "The DSCP field of the header.";
        }
      }
      case ipv6 {
        description
          "IPv6 flow identification.";
        leaf src-ipv6-address {
          type inet:ipv6-address;
          description
            "The source IP address of the header.";
        }
        leaf dest-ipv6-address {
          type inet:ipv6-address;
          description
            "The destination IP address of the header.";
        }
        leaf traffic-class {
          type uint8;
          description
            "The traffic class value of the header.";
        }
        leaf flow-label {
          type inet:ipv6-flow-label;
          description
            "The flow label of the header.";
        }
      }
    }
    leaf source-port {
      type inet:port-number;
      description
        "The source port number.";
    }
    leaf destination-port {
      type inet:port-number;
      description
        "The destination port number.";
    }
    leaf protocol {
      type uint8;
      description
        "The protocol id of the header.";
    }
  }

  grouping l3-flow-identification {
    description
      "Layer 3 flow identification in the DetNet 
       domain.";
    choice flow-type {
      description
        "L3 DetNet flow types: IP and MPLS.";
      case IP {
        description
          "IP (IPv4 or IPv6) flow identification.";
        uses ip-flow-identification; 
      }
      case MPLS {
        description
          "MPLS flow identification.";
        leaf service-label {
          type uint32;
          mandatory true;
          description
            "The service label.";
        }
      }
    }
  } //l3-flow-identification

  grouping in-segments {
    description
      "From a receiving node point of view, In-segments
       are a set of instances of a DetNet flow at the 
       receiving node. This occurs when Packet Replication
       Function (PRF) is enabled at an upstream node or 
       multiple flows map/aggregate to a single DetNet
       flow.";
    list in-segment {
      key "in-segment-id";
      
      description
        "A list of in segments, there will be 
         multiple in-segments for a DetNet flow
         when PRF and PEF enabled.";
         
      leaf in-segment-id {
        type uint32;
        description
          "in-segment identifier.";
      }
      
      uses l3-flow-identification;
      
      leaf service-function {
        type service-function-type;
        description
          "DetNet service function indication.";
      }
    }
  }
      
  grouping out-segments {
    description
      "Out-segments are a set of instances of 
       a DetNet flow, this occurs when implement
       packet replication function, where an 
       in-segment of a DetNet flow is replicated
       to multiple out-segments.";
       
    list out-segment {
      key "out-segment-id";
      description
        "A list of segments, there will be multiple
         out-segments when perform PRF.";
      leaf out-segment-id {
        type uint32;
        description
          "The out-segment identifier";
      }
      
      container detnet-service-encapsulation {
        description
          "Only MPLS based DetNet defines DetNet
           service layer. The service encapsulation
           includes service label and control word.";
        uses mpls-detnet-header;
      }
      
      container detnet-transport-encapsulation {
        description
          "Each out-segment corresponds to a 
           transport instance.";
        uses detnet-transport-instance;      
      }      
    }     
  }

  grouping detnet-service-instance{
    description
      "An end-2-end DetNet service is consisted of
       multiple segments. The concept of segment is 
       similar to PW segment. For DetNet, since the
       existing of PREOF, there could be three cases:
       1 - One in-segment maps to multiple 
           out-segments, when implement PRF; 
       2 - Multiple in-segments map to one 
           out-segment, when implement PEF;
       3 - Multiple in-segments map to multiple 
           out-segments, when implement a combination
           of PEF and PRF.";
           
    leaf name {
      type string;
      description
        "The name of the service instance. This MUST
         be unique across all service instances in
         a given network device.";
    }
    container flow-rank{
      description
        "TBD based on the data plane solution.";
    }
    container service-rank{
      description
        "TBD based on the data plane solution.";
    }
    uses in-segments;          
    uses out-segments;
  }
  
  grouping l2-flow-identification-at-uni {
    description
      "Layer 2 flow identification at UNI.";
    leaf source-mac-address {
      type yang:mac-address;
      description
        "The source MAC address used for 
         flow identification.";
    }
    leaf destination-mac-address {
      type yang:mac-address;
      description
        "The destination MAC address used for 
         flow identification.";
    }
    
    leaf ethertype {
      type eth:ethertype;
      description
        "The Ethernet Type (or Length) value represented
         in the canonical order defined by IEEE 802.
         The canonical representation uses lowercase
         characters.";
      reference
        "IEEE 802-2014 Clause 9.2";
    } 
    
    leaf vlan-id {
      type uint16 {
        range "1..4094";
      }
      description
        "Vlan Identifier used for L2 flow identification.";
    }
    container pcp {
      //Todo
      description
        "PCP used for L2 flow identification.";
    }
  }

  grouping l3-flow-identification-at-uni {
    description
      "Layer 3 flow identification at UNI.";
    uses ip-flow-identification;
  }

  grouping traffic-specification {
    description
      "traffic-specification specifies how the Source 
       transmits packets for the flow.  This is the 
       promise/request of the Source to the network.
       The network uses this traffic specification 
       to allocate resources and adjust queue 
       parameters in network nodes.";
    reference
      "draft-ietf-detnet-flow-information-model"; 
  
    leaf interval {
      type uint32;
      description
        "The period of time in which the traffic 
         specification cannot be exceeded";
    }  
    leaf max-packets-per-interval{
      type uint32;
      description
        "The maximum number of packets that the
         source will transmit in one Interval.";
    }  
    leaf max-payload-size{
      type uint32;
      description
         "The maximum payload size that the source 
          will transmit.";
    }
    leaf average-packets-per-interval {
      type uint32;
        description
          "The average number of packets that the
           source will transmit in one Interval";
    }
    leaf average-payload-size {
        type uint32;
        description
         "The average payload size that the 
          source will transmit.";
    }  
  }

  grouping client-flows-at-uni {
    description
      "The attributes of the client flow at UNI. When
       flow aggregation is enabled at ingress, multiple
       client flows map to a DetNet service instance.";
    list client-flow {
      key "flow-id";
      description
        "A list of client flows.";
      leaf flow-id {
        type uint32;
        description
          "Flow identifier that is unique in a network
           device for client flow identification";
      } 
      choice flow-type{
        description
          "Client flow type: layer 2 flow, layer 3 
           flow.";
        case l2-flow-identfication {
          description
            "Ethernet flow identification.";
          uses l2-flow-identification-at-uni;
        }
        case l3-flow-identification {
          description
            "layer 3 flow identification, including 
             IPv4,IPv6 and MPLS.";
          uses l3-flow-identification-at-uni;
        } 
      }
      container traffic-specification {
        description
          "The traffic specification of the client flow.";
        uses traffic-specification;
      }
    }
  }

  grouping detnet-service-proxy-instance {
    description
      "Maps between App-flows and DetNet flows";
    uses client-flows-at-uni;
    container detnet-service-instance {
      description
        "A DetNet service instance.";
      uses detnet-service-instance;
    }
  }

  container detnet-flow{
    description
      "DetNet flow configuration and status reporting.";
    choice detnet-node-role{
      description
        "Depends on the role of a node to configure 
         corresponding flow parameters.";
         
      case transit-node{
        description
          "DetNet flow configuration parameters for
           transit nodes.";
        container transit-node {
          description
            "transit node container.";
          uses detnet-transport-qos;
        }
      }
      case relay-node{
        description
          "DetNet flow configuration parameters for
           relay nodes.";
        container relay-node {
          description
            "Relay node container.";
          uses detnet-service-instance;
        }
      }
      case edge-node{
        description
          "DetNet flow configuration parameters for
           edge nodes.";
        container edge-node {
          description
            "Edge node container.";
          uses detnet-service-proxy-instance;
        }
      }
      case end-station {
        description
          "DetNet flow configuration parameters for
           end stations.";
        container end-station {
          description
            "End station container.";
          uses detnet-service-proxy-instance;
        }
      }
    }
  }
}
<CODE ENDS>

8. DetNet Configuration Model Classification

This section defines three classes of DetNet configuration model: fully distributed configuration model, fully centralized configuration model, hybrid configuration model, based on different network architectures, showing how configuration information exchanges between various entities in the network.

8.1. Fully Distributed Configuration Model

In a fully distributed configuration model, UNI information is transmitted over DetNet UNI protocol from the user side to the network side; then UNI information and network configuration information propagate in the network over distributed control plane protocol. For example:

1) IGP collects topology information and DetNet capabilities of network([I-D.geng-detnet-info-distribution]);

2) Control Plane of the Edge Node(Ingress) receives a flow establishment request from UNI and calculates a/some valid path(s);

3) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request.

Current distributed control plane protocol,e.g., RSVP-TE[RFC3209], SRP[IEEE802.1Qcc], can only reserve bandwidth along the path, while the configuration of a fine-grained schedule, e.g.,Time Aware Shaping(TAS) defined in [IEEE802.1Qbv], is not supported.

The fully distributed configuration model is not covered by this draft. It should be discussed in the future DetNet control plane work.

8.2. Fully Centralized Configuration Model

In the fully centralized configuration model, UNI information is transmitted from Centralized User Configuration (CUC) to Centralized Network Configuration(CNC). Configurations of routers for DetNet flows are performed by CNC with network management protocol. For example:

1) CNC collects topology information and DetNet capability of network through Netconf;

2) CNC receives a flow establishment request from UNI and calculates a/some valid path(s);

3) CNC configures the devices along the path for flow transmission.

8.3. Hybrid Configuration Model

In the hybrid configuration model, controller and control plane protocols work together to offer DetNet service, and there are a lot of possible combinations. For example:

1) CNC collects topology information and DetNet capability of network through IGP/BGP-LS;

2) CNC receives a flow establishment request from UNI and calculates a/some valid path(s);

3) Based on the calculation result, CNC distributes flow path information to Edge Node(Ingress) and other information(e.g. replication/elimination) to the relevant nodes.

4) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request.

or

1) Controller collects topology information and DetNet capability of network through IGP/BGP-LS;

2) Control Plane of Edge Node(Ingress) receives a flow establishment request from UNI;

3) Edge Node(Ingress) sends the path establishment request to CNC through PCEP;

4) After Calculation, CNC sends back the path information of the flow to the Edge Node(Ingress) through PCEP;

5) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request.

There are also other variations that can be included in the hybrid model. This draft can not coverer all the control plane data needed in hybrid configuration models. Every solution has there own mechanism and corresponding parameters to make it work.

Editor's Note:

1. There are a lot of optional DetNet configuration models, and different scenario in different use case can choose one of them based on its conditions. Maybe next step of the work is to pick up one or more typical scenarios and give a practical solution.

2. [IEEE802.1Qcc] also defines three TSN configuration models: fully-centralized model, fully-distributed model, centralized Network / distributed User Model. This section defines the configuration model roughly the same, to keep the design of L2 and L3 in the same structure. Hybrid configuration model is slightly different from the 'centralized Network / distributed User Model'. The hybrid configuration model intends to contain more variations.

9. Open issues

There are some open issues that are still under disccusion:

These issues will be resolved in the following versions of the draft.

10. IANA Considerations

This document makes no request of IANA.

Note to RFC Editor: this section may be removed on publication as an RFC.

11. Security Considerations

<TBD>

12. Acknowledgements

13. References

13.1. Normative References

[I-D.finn-detnet-bounded-latency] Finn, N., Boudec, J., Mohammadpour, E., Varga, B. and J. Farkas, "DetNet Bounded Latency", Internet-Draft draft-finn-detnet-bounded-latency-01, July 2018.
[I-D.ietf-detnet-architecture] Finn, N., Thubert, P., Varga, B. and J. Farkas, "Deterministic Networking Architecture", Internet-Draft draft-ietf-detnet-architecture-08, September 2018.
[I-D.ietf-detnet-dp-sol-ip] Korhonen, J. and B. Varga, "DetNet IP Data Plane Encapsulation", Internet-Draft draft-ietf-detnet-dp-sol-ip-00, July 2018.
[I-D.ietf-detnet-dp-sol-mpls] Korhonen, J. and B. Varga, "DetNet MPLS Data Plane Encapsulation", Internet-Draft draft-ietf-detnet-dp-sol-mpls-00, July 2018.
[I-D.ietf-detnet-flow-information-model] Farkas, J., Varga, B., rodney.cummings@ni.com, r., Jiang, Y. and Y. Zha, "DetNet Flow Information Model", Internet-Draft draft-ietf-detnet-flow-information-model-01, March 2018.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997.
[RFC6991] Schoenwaelder, J., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013.
[RFC7950] Bjorklund, M., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016.

13.2. Informative References

[I-D.geng-detnet-info-distribution] Geng, X., Chen, M. and Z. Li, "IGP-TE Extensions for DetNet Information Distribution", Internet-Draft draft-geng-detnet-info-distribution-02, March 2018.
[I-D.ietf-detnet-use-cases] Grossman, E., "Deterministic Networking Use Cases", Internet-Draft draft-ietf-detnet-use-cases-19, October 2018.
[I-D.ietf-teas-yang-te] Saad, T., Gandhi, R., Liu, X., Beeram, V., Shah, H. and I. Bryskin, "A YANG Data Model for Traffic Engineering Tunnels and Interfaces", Internet-Draft draft-ietf-teas-yang-te-17, October 2018.
[I-D.ietf-teas-yang-te-topo] Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H. and O. Dios, "YANG Data Model for Traffic Engineering (TE) Topologies", Internet-Draft draft-ietf-teas-yang-te-topo-18, June 2018.
[I-D.thubert-tsvwg-detnet-transport] Thubert, P., "A Transport Layer for Deterministic Networks", Internet-Draft draft-thubert-tsvwg-detnet-transport-01, October 2017.
[I-D.varga-detnet-service-model] Varga, B. and J. Farkas, "DetNet Service Model", Internet-Draft draft-varga-detnet-service-model-02, May 2017.
[IEEE802.1CB] , "IEEE, "Frame Replication and Elimination for Reliability (IEEE Draft P802.1CB)", 2017, <http://www.ieee802.org/1/files/private/cb-drafts/>.", 2016.
[IEEE802.1Q-2014] "IEEE, "IEEE Std 802.1Q Bridges and Bridged Networks", 2014, <http://ieeexplore.ieee.org/document/6991462/>.", 2014.
[IEEE802.1Qbu] , "IEEE, "IEEE Std 802.1Qbu Bridges and Bridged Networks - Amendment 26: Frame Preemption", 2016, <http://ieeexplore.ieee.org/document/7553415/>.", 2016.
[IEEE802.1Qbv] , "IEEE, "IEEE Std 802.1Qbu Bridges and Bridged Networks - Amendment 25: Enhancements for Scheduled Traffic", 2015, <http://ieeexplore.ieee.org/document/7572858/>.", 2016.
[IEEE802.1Qcc] , "IEEE, "Stream Reservation Protocol (SRP) Enhancements and Performance Improvements (IEEE Draft P802.1Qcc)", 2017, <http://www.ieee802.org/1/files/private/cc-drafts/>."
[IEEE802.1Qch] , "IEEE, "Cyclic Queuing and Forwarding (IEEE Draft P802.1Qch)", 2017, <http://www.ieee802.org/1/files/private/ch-drafts/>.", 2016.
[IEEE802.1Qci] , "IEEE, "Per-Stream Filtering and Policing (IEEE Draft P802.1Qci)", 2016, <http://www.ieee802.org/1/files/private/ci-drafts/>.", 2016.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V. and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001.
[RFC4875] Aggarwal, R., Papadimitriou, D. and S. Yasukawa, "Extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for Point-to-Multipoint TE Label Switched Paths (LSPs)", RFC 4875, DOI 10.17487/RFC4875, May 2007.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K. and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018.

Authors' Addresses

Xuesong Geng Huawei EMail: gengxuesong@huawei.com
Mach(Guoyi) Chen Huawei EMail: mach.chen@huawei.com
Zhenqiang Li China Mobile EMail: lizhenqiang@chinamobile.com
Reshad Rahman Cisco Systems EMail: rrahman@cisco.com