SPRING Working Group R. Gandhi, Ed. Internet-Draft C. Filsfils Intended status: Informational Cisco Systems, Inc. Expires: September 24, 2020 D. Voyer Bell Canada M. Chen Huawei B. Janssens Colt March 23, 2020 Performance Measurement Using TWAMP Light for Segment Routing Networks draft-gandhi-spring-twamp-srpm-08 Abstract Segment Routing (SR) leverages the source routing paradigm. SR is applicable to both Multiprotocol Label Switching (SR-MPLS) and IPv6 (SRv6) data planes. This document specifies procedure for sending and processing probe query and response messages for Performance Measurement (PM) in Segment Routing networks. The procedure uses the messages defined in RFC 5357 (Two-Way Active Measurement Protocol (TWAMP) Light) for Delay Measurement, and uses the messages defined in this document for Loss Measurement. The procedure specified is applicable to SR-MPLS and SRv6 data planes and is used for both Links and end-to-end SR Policies. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on September 24, 2020. Gandhi, et al. Expires September 24, 2020 [Page 1] Internet-Draft TWAMP Light for Segment Routing March 2020 Copyright Notice Copyright (c) 2020 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Conventions Used in This Document . . . . . . . . . . . . . . 3 2.1. Requirements Language . . . . . . . . . . . . . . . . . . 4 2.2. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 4 2.3. Reference Topology . . . . . . . . . . . . . . . . . . . 5 3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. Example Provisioning Model . . . . . . . . . . . . . . . 6 4. Probe Messages . . . . . . . . . . . . . . . . . . . . . . . 7 4.1. Probe Query Message . . . . . . . . . . . . . . . . . . . 7 4.1.1. Delay Measurement Query Message . . . . . . . . . . . 7 4.1.2. Loss Measurement Query Message . . . . . . . . . . . 8 4.1.3. Probe Query for Links . . . . . . . . . . . . . . . . 9 4.1.4. Probe Query for End-to-end Measurement for SR Policy 9 4.1.5. Control Code Field for TWAMP Light Messages . . . . . 10 4.1.6. Loss Measurement Query Message Formats for TWAMP Light . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2. Probe Response Message . . . . . . . . . . . . . . . . . 14 4.2.1. One-way Measurement Mode . . . . . . . . . . . . . . 15 4.2.2. Two-way Measurement Mode . . . . . . . . . . . . . . 15 4.2.3. Loopback Measurement Mode . . . . . . . . . . . . . . 17 4.2.4. Loss Measurement Response Message Formats for TWAMP Light . . . . . . . . . . . . . . . . . . . . . . . . 17 5. Performance Measurement for P2MP SR Policies . . . . . . . . 19 6. ECMP Support for SR Policies . . . . . . . . . . . . . . . . 20 7. Additional Message Processing Rules . . . . . . . . . . . . . 20 7.1. TTL and Hop Limit . . . . . . . . . . . . . . . . . . . . 21 7.2. Router Alert Option . . . . . . . . . . . . . . . . . . . 21 7.3. UDP Checksum . . . . . . . . . . . . . . . . . . . . . . 21 8. Security Considerations . . . . . . . . . . . . . . . . . . . 22 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 22 Gandhi, et al. Expires September 24, 2020 [Page 2] Internet-Draft TWAMP Light for Segment Routing March 2020 10.1. Normative References . . . . . . . . . . . . . . . . . . 22 10.2. Informative References . . . . . . . . . . . . . . . . . 23 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 26 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 26 1. Introduction Segment Routing (SR) leverages the source routing paradigm and greatly simplifies network operations for Software Defined Networks (SDNs). SR is applicable to both Multiprotocol Label Switching (SR- MPLS) and IPv6 (SRv6) data planes. SR takes advantage of the Equal- Cost Multipaths (ECMPs) between source and transit nodes, between transit nodes and between transit and destination nodes. SR Policies as defined in [I-D.ietf-spring-segment-routing-policy] are used to steer traffic through a specific, user-defined paths using a stack of Segments. Built-in SR Performance Measurement (PM) is one of the essential requirements to provide Service Level Agreements (SLAs). The One-Way Active Measurement Protocol (OWAMP) defined in [RFC4656] and Two-Way Active Measurement Protocol (TWAMP) defined in [RFC5357] provide capabilities for the measurement of various performance metrics in IP networks using probe messages. These protocols rely on control-channel signaling to establish a test-channel over an UDP path. The TWAMP Light [Appendix I in RFC5357] [BBF.TR-390] provides simplified mechanisms for active performance measurement in Customer IP networks by provisioning UDP paths and eliminates the control- channel signaling. As described in Appendix A of [RFC8545], TWAMP Light mechanism is informative only. These protocols lack support for direct-mode Loss Measurement (LM) to detect actual Customer data traffic loss which is required in SR networks. This document specifies procedures for sending and processing probe query and response messages for Performance Measurement in SR networks. The procedure uses the messages defined in [RFC5357] (TWAMP Light) for Delay Measurement (DM), and uses the messages defined in this document for Loss Measurement. The procedure specified is applicable to SR-MPLS and SRv6 data planes and are used for both Links and end-to-end SR Policies. This document also defines mechanisms for handling ECMPs of SR Policies for performance delay measurement. Unless otherwise specified, the messages defined in [RFC5357] are not modified by this document. 2. Conventions Used in This Document Gandhi, et al. Expires September 24, 2020 [Page 3] Internet-Draft TWAMP Light for Segment Routing March 2020 2.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 2.2. Abbreviations BSID: Binding Segment ID. DM: Delay Measurement. ECMP: Equal Cost Multi-Path. HMAC: Hashed Message Authentication Code. LM: Loss Measurement. MPLS: Multiprotocol Label Switching. NTP: Network Time Protocol. OWAMP: One-Way Active Measurement Protocol. PM: Performance Measurement. PSID: Path Segment Identifier. PTP: Precision Time Protocol. SID: Segment ID. SL: Segment List. SR: Segment Routing. SRH: Segment Routing Header. SR-MPLS: Segment Routing with MPLS data plane. SRv6: Segment Routing with IPv6 data plane. TC: Traffic Class. TWAMP: Two-Way Active Measurement Protocol. Gandhi, et al. Expires September 24, 2020 [Page 4] Internet-Draft TWAMP Light for Segment Routing March 2020 2.3. Reference Topology In the reference topology shown below, the sender node R1 initiates a probe query for performance measurement and the reflector node R5 sends a probe response for the query message received. The probe response is sent to the sender node R1. The nodes R1 and R5 may be directly connected via a Link or there exists a Point-to-Point (P2P) SR Policy [I-D.ietf-spring-segment-routing-policy] on node R1 with destination to node R5. In case of Point-to-Multipoint (P2MP), SR Policy originating from source node R1 may terminate on multiple destination leaf nodes [I-D.voyer-spring-sr-replication-segment]. +-------+ t1 Query t2 +-------+ | | - - - - - - - - - ->| | | R1 |---------------------| R5 | | |<- - - - - - - - - - | | +-------+ t4 Response t3 +-------+ Sender Reflector Reference Topology 3. Overview For one-way, two-way and round-trip delay measurements in Segment Routing networks, the probe messages defined in [RFC5357] are used. For direct-mode and inferred-mode loss measurements in Segment Routing networks, the messages defined in this document are used. Separate UDP destination port numbers are user-configured for delay and loss measurements. As specified in [RFC8545], the reflector supports the destination UDP port 862 for delay measurement probe messages by default. This UDP port however, is not used for loss measurement probe messages defined in this document. The sender uses the UDP port number following the guidelines specified in Section 6 in [RFC6335]. For both Links and end-to-end SR Policies, no PM session for delay or loss measurement is created on the reflector node R5 [RFC5357]. For Performance Measurement, probe query and response messages are sent as following: o For Delay Measurement, the probe messages are sent on the congruent path of the data traffic by the sender node, and are used to measure the delay experienced by the actual data traffic flowing on the Links and SR Policies. o For Loss Measurement, the probe messages are sent on the congruent path of the data traffic by the sender node, and are used to Gandhi, et al. Expires September 24, 2020 [Page 5] Internet-Draft TWAMP Light for Segment Routing March 2020 collect the receive traffic counters for the incoming link or incoming SID where the probe query messages are received at the reflector node (incoming link or incoming SID needed since the reflector node does not have PM session state present). The In-Situ Operations, Administration, and Maintenance (IOAM) mechanisms for SR-MPLS defined in [I-D.gandhi-mpls-ioam-sr] and for SRv6 defined in [I-D.ali-spring-ioam-srv6] are used to carry PM information such as timestamp in-band as part of the data packets, and are outside the scope of this document. 3.1. Example Provisioning Model An example of a provisioning model and typical measurement parameters for each user-configured destination UDP port for performance delay and loss measurements is shown in the following Figure 1: +------------+ | Controller | +------------+ Destination UDP Port / \ Destination UDP port Measurement Protocol / \ Measurement Protocol Measurement Type / \ Measurement Type Delay/Loss / \ Delay/Loss Authentication Mode & Key / \ Authentication Mode & Key Timestamp Format / \ Loss Measurement Mode Delay Measurement Mode / \ Loss Measurement Mode / \ v v +-------+ +-------+ | | | | | R1 |------------| R5 | | | | | +-------+ +-------+ Sender Reflector Figure 1: Example Provisioning Model Example of Measurement Protocol is TWAMP Light, the Timestamp Format is PTPv2 [IEEE1588] or NTP and the Loss Measurement mode is inferred- mode or direct-mode. The mechanisms to provision the sender and reflector nodes are outside the scope of this document. The reflector node R5 uses the parameters for the timestamp format and delay measurement mode (i.e. one-way, two-way or loopback mode) from the received probe query message. Gandhi, et al. Expires September 24, 2020 [Page 6] Internet-Draft TWAMP Light for Segment Routing March 2020 4. Probe Messages 4.1. Probe Query Message The probe messages defined in [RFC5357] are used for Delay Measurement for Links and end-to-end SR Policies. For Loss Measurement, the probe messages defined in this document are used. The Sender IPv4 or IPv6 address is used as the source address. When known, the reflector IPv4 or IPv6 address is used as the destination address. If not known, the address in the range of 127/8 for IPv4 or 0:0:0:0:0:FFFF:7F00/104 for IPv6 is used as destination address. This is the case for example, when using SR Policy with IPv4 endpoint of 0.0.0.0 or IPv6 endpoint of ::0 [I-D.ietf-spring-segment-routing-policy]. 4.1.1. Delay Measurement Query Message The message content for Delay Measurement probe query message using UDP header [RFC0768] is shown in Figure 2. The DM probe query message is sent with user-configured Destination UDP port number for DM. The Destination UDP port cannot be used as Source port, since the message does not have any indication to distinguish between the query and response message. The payload of the DM probe query message contains the delay measurement message defined in Section 4.1.2 of [RFC5357]. For symmetrical size query and response messages as defined in [RFC6038], the DM probe query message contains the payload format defined in Section 4.2.1 of [RFC5357]. +---------------------------------------------------------------+ | IP Header | . Source IP Address = Sender IPv4 or IPv6 Address . . Destination IP Address = Reflector IPv4 or IPv6 Address . . Protocol = UDP . . . +---------------------------------------------------------------+ | UDP Header | . Source Port = As chosen by Sender . . Destination Port = User-configured Port for Delay Measurement. . . +---------------------------------------------------------------+ | Payload = Message as specified in Section 4.2.1 of RFC 5357 | | . Payload = Message as specified in Section 4.1.2 of RFC 5357 | . . . +---------------------------------------------------------------+ Figure 2: DM Probe Query Message Gandhi, et al. Expires September 24, 2020 [Page 7] Internet-Draft TWAMP Light for Segment Routing March 2020 Timestamp field is eight bytes and use the format defined in Section 4.2.1 of [RFC5357]. It is recommended to use the IEEE 1588v2 Precision Time Protocol (PTP) truncated 64-bit timestamp format [IEEE1588] as specified in [RFC8186], with hardware support in Segment Routing networks. 4.1.1.1. Delay Measurement Authentication Mode When using the authenticated mode for delay measurement, the matching authentication type (e.g. HMAC-SHA-256) and key are user-configured on both the sender and reflector nodes. A separate user-configured destination UDP port is used for the delay measurement in authentication mode due to the different probe message format. 4.1.2. Loss Measurement Query Message The message content for Loss Measurement probe query message using UDP header [RFC0768] is shown in Figure 3. The LM probe query message is sent with user-configured Destination UDP port number for LM, which is a different Destination UDP port number than DM. Separate Destination UDP ports are used for direct-mode and inferred- mode loss measurements. The Destination UDP port cannot be used as Source port, since the message does not have any indication to distinguish between the query and response message. The LM probe query message contains the payload for loss measurement as defined in Figure 7 and Figure 8. +---------------------------------------------------------------+ | IP Header | . Source IP Address = Sender IPv4 or IPv6 Address . . Destination IP Address = Reflector IPv4 or IPv6 Address . . Protocol = UDP . . . +---------------------------------------------------------------+ | UDP Header | . Source Port = As chosen by Sender . . Destination Port = User-configured Port for Loss Measurement . . . +---------------------------------------------------------------+ | Payload = Message as specified in Figure 7 or 8 | . . +---------------------------------------------------------------+ Figure 3: LM Probe Query Message Gandhi, et al. Expires September 24, 2020 [Page 8] Internet-Draft TWAMP Light for Segment Routing March 2020 4.1.2.1. Loss Measurement Authentication Mode When using the authenticated mode for loss measurement, the matching authentication type (e.g. HMAC-SHA-256) and key are user-configured on both the sender and reflector nodes. A separate user-configured destination UDP port is used for the loss measurement in authentication mode due to the different message format. 4.1.3. Probe Query for Links The probe query message as defined in Figure 2 for delay measurement and Figure 3 for loss measurement is sent on the congruent path of the data traffic. The probe messages are routed over the Link for both delay and loss measurement. 4.1.4. Probe Query for End-to-end Measurement for SR Policy The performance delay and loss measurement for segment routing is applicable to both SR-MPLS and SRv6 Policies. 4.1.4.1. Probe Query Message for SR-MPLS Policy The probe query messages for end-to-end performance measurement of an SR-MPLS Policy is sent using its SR-MPLS header containing the MPLS segment list as shown in Figure 4. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Segment(1) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Segment(n) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PSID | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message as shown in Figure 2 for DM or Figure 3 for LM | . . +---------------------------------------------------------------+ Figure 4: Probe Query Message for SR-MPLS Policy The Segment List (SL) can be empty to indicate Implicit NULL label case for a single-hop SR Policy. Gandhi, et al. Expires September 24, 2020 [Page 9] Internet-Draft TWAMP Light for Segment Routing March 2020 The Path Segment Identifier (PSID) [I-D.ietf-spring-mpls-path-segment] of the SR-MPLS Policy is used for accounting received traffic on the egress node for loss measurement. 4.1.4.2. Probe Query Message for SRv6 Policy An SRv6 Policy setup using the SRv6 Segment Routing Header (SRH) and a Segment List as defined in [RFC8754]. For SRv6, network programming is defined in [I-D.ietf-spring-srv6-network-programming]. The probe query messages for end-to-end performance measurement of an SRv6 Policy is sent using its SRH with Segment List as shown in Figure 5. +---------------------------------------------------------------+ | SRH | . . +---------------------------------------------------------------+ | Message as shown in Figure 2 for DM or Figure 3 for LM | . (Using IPv6 Source and Destination Addresses) . . . +---------------------------------------------------------------+ Figure 5: Probe Query Message for SRv6 Policy For delay measurement of SRv6 Policy using SRH, END function END.OTP [I-D.ietf-6man-spring-srv6-oam] is used with the target SRv6 SID to punt probe messages on the target node, as shown in Figure 5. Similarly, for loss measurement of SRv6 Policy, END function END.OP [I-D.ietf-6man-spring-srv6-oam] is used with target SRv6 SID to punt probe messages on the target node. 4.1.5. Control Code Field for TWAMP Light Messages The Control Code field is defined for delay and loss measurement probe query and response messages for TWAMP Light in unauthenticated and authenticated modes. The modified delay measurement probe query and response message format is shown in Figure 6. This message format is backwards compatible with the message format defined in [RFC5357] as its reflectors ignore the received field (previously identified as MBZ). The usage of the Control Code is not limited to the SR networks and can be used for various bidirectional paths in a network. Gandhi, et al. Expires September 24, 2020 [Page 10] Internet-Draft TWAMP Light for Segment Routing March 2020 . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Timestamp | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Error Estimate | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ |Se Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Session-Sender Error Estimate | MBZ |Re Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Ses-Sender TTL | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . Figure 6: Control Code in TWAMP Light Message Sender Control Code: Set as follows in TWAMP Light probe query message. For a Query: 0x0: Out-of-band Response Requested. Indicates that the probe response is not required over the same path in the reverse direction. This is also the default behavior. 0x1: In-band Response Requested. Indicates that this query has been sent over a bidirectional path and the probe response is required over the same path in the reverse direction. The bidirectional path does not have to be an SR path. Reflector Control Code: Set as follows in TWAMP Light probe response message. For a Response: 0x1: Error - Invalid Message. Indicates that the operation failed because the received query message could not be processed. Gandhi, et al. Expires September 24, 2020 [Page 11] Internet-Draft TWAMP Light for Segment Routing March 2020 Additional Error Codes to be defined in future. 4.1.6. Loss Measurement Query Message Formats for TWAMP Light In this document, TWAMP Light probe query message formats are defined for loss measurement as shown in Figure 7 and Figure 8. The message formats are hardware efficient due to the well-known locations of the counters. They are similar to the delay measurement message formats (e.g. location of the Counter and Timestamp) and do not require any backwards compatibility or support for the existing DM message formats from [RFC5357] as different user-configured destination UDP port is used for loss measurement. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transmit Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved | Block Number | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ |Se Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . Packet Padding . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7: TWAMP Light LM Probe Query Message - Unauthenticated Mode Gandhi, et al. Expires September 24, 2020 [Page 12] Internet-Draft TWAMP Light for Segment Routing March 2020 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ (12 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transmit Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved | Block Number | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ |Se Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | HMAC (16 octets) | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . Packet Padding . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 8: TWAMP Light LM Probe Query Message - Authenticated Mode Sequence Number (32-bit): As defined in [RFC5357]. Transmit Counter (64-bit): The number of packets or octets sent by the sender node in the query message and by the reflector node in the response message. The counter is always written at the well-known location in the probe query and response messages. Receive Counter (64-bit): The number of packets or octets received at the reflector node. It is written by the reflector node in the probe response message. Sender Counter (64-bit): This is the exact copy of the transmit counter from the received query message. It is written by the reflector node in the probe response message. Sender Sequence Number (32-bit): As defined in [RFC5357]. Sender TTL: As defined in Section 7.1. LM Flags: The meanings of the Flag bits are: Gandhi, et al. Expires September 24, 2020 [Page 13] Internet-Draft TWAMP Light for Segment Routing March 2020 X: Extended counter format indicator. Indicates the use of extended (64-bit) counter values. Initialized to 1 upon creation (and prior to transmission) of an LM Query and copied from an LM Query to an LM response. Set to 0 when the LM message is transmitted or received over an interface that writes 32-bit counter values. B: Octet (byte) count. When set to 1, indicates that the Counter 1-4 fields represent octet counts. The octet count applies to all packets within the LM scope, and the octet count of a packet sent or received includes the total length of that packet (but excludes headers, labels, or framing of the channel itself). When set to 0, indicates that the Counter fields represent packet counts. Block Number (8-bit): The Loss Measurement using Alternate-Marking method defined in [RFC8321] requires to color the data traffic. To be able to compare the transmit and receive traffic counters of the matching color, the Block Number (or color) of the traffic counters is carried by the probe query and response messages for loss measurement. HMAC: The PM probe message in authenticated mode includes a key Hashed Message Authentication Code (HMAC) ([RFC2104]) hash. Each probe query and response messages are authenticated by adding Sequence Number with Hashed Message Authentication Code (HMAC) TLV. It can use HMAC-SHA-256 truncated to 128 bits (similarly to the use of it in IPSec defined in [RFC4868]); hence the length of the HMAC field is 16 octets. HMAC uses its own key and the mechanism to distribute the HMAC key is outside the scope of this document. In authenticated mode, only the sequence number is encrypted, and the other payload fields are sent in clear text. The probe message may include Comp.MBZ (Must Be Zero) variable length field to align the packet on 16 octets boundary. 4.2. Probe Response Message The probe response message is sent using the IP/UDP information from the received probe query message. The content of the probe response message is shown in Figure 9. Gandhi, et al. Expires September 24, 2020 [Page 14] Internet-Draft TWAMP Light for Segment Routing March 2020 +---------------------------------------------------------------+ | IP Header | . Source IP Address = Reflector IPv4 or IPv6 Address . . Destination IP Address = Source IP Address from Query . . Protocol = UDP . . . +---------------------------------------------------------------+ | UDP Header | . Source Port = As chosen by Reflector . . Destination Port = Source Port from Query . . . +---------------------------------------------------------------+ | DM Payload as specified in Section 4.2.1 of RFC 5357 | | . LM Payload as specified in Figure 12 or 13 . . . +---------------------------------------------------------------+ Figure 9: Probe Response Message 4.2.1. One-way Measurement Mode In one-way performance measurement mode, the probe response message as defined in Figure 9 is sent back out-of-band to the sender node, for both Links and SR Policies. The Sender Control Code is set to "Out-of-band Response Requested". In this delay measurement mode, as per Reference Topology, all timestamps t1, t2, t3, and t4 are collected by the probes. However, only timestamps t1 and t2 are needed to measure one-way delay. 4.2.2. Two-way Measurement Mode In two-way performance measurement mode, when using a bidirectional path, the probe response message as defined in Figure 9 is sent back to the sender node on the congruent path of the data traffic on the same reverse direction Link or associated reverse SR Policy [I-D.ietf-pce-sr-bidir-path]. The Sender Control Code is set to "In- band Response Requested". In this delay measurement mode, as per Reference Topology, all timestamps t1, t2, t3, and t4 are collected by the probes. All four timestamps are needed to measure two-way delay. Specifically, the probe response message is sent back on the incoming physical interface where the probe query message is received. This is useful for example, in case of two-way measurement mode for Link delay. Gandhi, et al. Expires September 24, 2020 [Page 15] Internet-Draft TWAMP Light for Segment Routing March 2020 4.2.2.1. Probe Response Message for SR-MPLS Policy The message content for sending probe response message for two-way end-to-end performance measurement of an SR-MPLS Policy is shown in Figure 10. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Segment(1) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Segment(n) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message as shown in Figure 9 | . . +---------------------------------------------------------------+ Figure 10: Probe Response Message for SR-MPLS Policy The Path Segment Identifier (PSID) [I-D.ietf-spring-mpls-path-segment] of the forward SR Policy in the probe query can be used to find the associated reverse SR Policy [I-D.ietf-pce-sr-bidir-path] to send the probe response message for two-way measurement of SR Policy. 4.2.2.2. Probe Response Message for SRv6 Policy The message content for sending probe response message on the congruent path of the data traffic for two-way end-to-end performance measurement of an SRv6 Policy with SRH is shown in Figure 11. +---------------------------------------------------------------+ | SRH | . . +---------------------------------------------------------------+ | Message as shown in Figure 9 | . (Using IPv6 Source and Destination Addresses) . . . +---------------------------------------------------------------+ Figure 11: Probe Response Message for SRv6 Policy Gandhi, et al. Expires September 24, 2020 [Page 16] Internet-Draft TWAMP Light for Segment Routing March 2020 4.2.3. Loopback Measurement Mode The Loopback measurement mode can be used to measure round-trip delay for a bidirectional SR Path. The IP header of the probe query message contains the destination address equals to the sender address and the source address equals to the reflector address. Optionally, the probe query message can carry the reverse path information (e.g. reverse path label stack for SR-MPLS) as part of the SR header. The probe messages are not punted at the reflector node and it does not process them and generate response messages. The Sender Control Code is set to the default value of 0. In this mode, as the probe packet is not punted on the reflector node for processing, the querier copies the 'Sequence Number' in 'Session-Sender Sequence Number' directly. In this delay measurement mode, as per Reference Topology, the timestamps t1 and t4 are collected by the probes. Both these timestamps are needed to measure round-trip delay. 4.2.4. Loss Measurement Response Message Formats for TWAMP Light In this document, TWAMP Light probe response message formats are defined for loss measurement as shown in Figure 12 and Figure 13. Gandhi, et al. Expires September 24, 2020 [Page 17] Internet-Draft TWAMP Light for Segment Routing March 2020 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transmit Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved | Block Number | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Receive Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved |Sender Block Nu| MBZ |Re Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender TTL | | +-+-+-+-+-+-+-+-+ + | Packet Padding | . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 12: TWAMP Light LM Probe Response Message - Unauthenticated Mode 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ (12 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transmit Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved | Block Number | MBZ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ (4 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Receive Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Gandhi, et al. Expires September 24, 2020 [Page 18] Internet-Draft TWAMP Light for Segment Routing March 2020 | MBZ (8 octets) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ (12 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender Counter | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X|B| Reserved |Sender Block Nu| MBZ |Re Control Code| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ (4 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sender TTL | | +-+-+-+-+-+-+-+-+ | | MBZ (15 octets) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | HMAC (16 octets) | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . Packet Padding . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 13: TWAMP Light LM Probe Response Message - Authenticated Mode 5. Performance Measurement for P2MP SR Policies The procedures for delay and loss measurement described in this document for Point-to-Point (P2P) SR Policies [I-D.ietf-spring-segment-routing-policy] are also equally applicable to the Point-to-Multipoint (P2MP) SR Policies as following: o The sender root node sends probe query messages using the Replication Segment defined in [I-D.voyer-spring-sr-replication-segment] for the P2MP SR Policy as shown in Figure 14. o Each reflector leaf node sends its IP address in the Source Address of the probe response messages as shown in Figure 9. This Gandhi, et al. Expires September 24, 2020 [Page 19] Internet-Draft TWAMP Light for Segment Routing March 2020 allows the sender root node to identify the reflector leaf nodes of the P2MP SR Policy. o The P2MP root node measures the end-to-end delay and loss performance for each P2MP leaf node of the P2MP SR Policy. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Replication SID | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message as shown in Figure 2 for DM or Figure 3 for LM | . . +---------------------------------------------------------------+ Figure 14: Query with Replication Segment for SR-MPLS Policy 6. ECMP Support for SR Policies An SR Policy can have ECMPs between the source and transit nodes, between transit nodes and between transit and destination nodes. Usage of Anycast SID [RFC8402] by an SR Policy can result in ECMP paths via transit nodes part of that Anycast group. The PM probe messages need to be sent to traverse different ECMP paths to measure performance delay of an SR Policy. Forwarding plane has various hashing functions available to forward packets on specific ECMP paths. The mechanisms described in [RFC8029] and [RFC5884] for handling ECMPs are also applicable to the performance measurement. In the IP header of the PM probe messages, sweeping of Destination Addresses in 127/8 range for IPv4 or 0:0:0:0:0:FFFF:7F00/104 range for IPv6 can be used to exercise particular ECMP paths. As specified in [RFC6437], Flow Label field in the outer IPv6 header can also be used for sweeping. The considerations for performance loss measurement for different ECMP paths of an SR Policy are outside the scope of this document. 7. Additional Message Processing Rules The processing rules defined in this section are applicable to TWAMP Light messages for delay and loss measurement for Links and end-to- end SR Policies. Gandhi, et al. Expires September 24, 2020 [Page 20] Internet-Draft TWAMP Light for Segment Routing March 2020 7.1. TTL and Hop Limit The TTL field in the IPv4 and MPLS headers of the probe query messages is set to 255 [RFC5357]. Similarly, the Hop Limit field in the IPv6 and SRH headers of the probe query messages is set to 255 [RFC5357]. When using the Destination IPv4 Address from the 127/8 range, the TTL in the IPv4 header is set to 1 [RFC8029]. Similarly, when using the Destination IPv6 Address from the 0:0:0:0:0:FFFF:7F00/104 range, the Hop Limit field in the inner IPv6 header is set to 1 whereas in the outer IPv6 header is set to 255. For Link performance delay and loss measurements, the TTL and Hop Limit field in the probe message is set to 1 in both one-way and two- way measurement modes. 7.2. Router Alert Option The Router Alert IP option is not set when using the routable Destination IP Address in the probe messages. When using the Destination IPv4 Address from the 127/8 range, to be able to punt probe packets on the reflector node, the Router Alert IP Option of value 0x0 [RFC2113] for IPv4 may be added [RFC8029]. Similarly, when using the Destination IPv6 Address from the 0:0:0:0:0:FFFF:7F00/104 range, the Router Alert IP Option of value 69 [RFC7506] for IPv6 may be added in the destination option header, Section 4.6 of [RFC8200]. For SRv6 Policy using SRH, it is added in the inner IPv6 header. 7.3. UDP Checksum The UDP Checksum Complement for delay and loss measurement messages follows the procedure defined in [RFC7820] and can be optionally used with the procedures defined in this document. For IPv4 and IPv6 probe messages, where the hardware is not capable of re-computing the UDP checksum or adding checksum complement [RFC7820], the sender node sets the UDP checksum to 0 [RFC6936] [RFC8085]. The receiving node bypasses the checksum validation and accepts the packets with UDP checksum value 0 for the UDP port being used for PM delay and loss measurements. Gandhi, et al. Expires September 24, 2020 [Page 21] Internet-Draft TWAMP Light for Segment Routing March 2020 8. Security Considerations The performance measurement is intended for deployment in well- managed private and service provider networks. As such, it assumes that a node involved in a measurement operation has previously verified the integrity of the path and the identity of the far-end reflector node. If desired, attacks can be mitigated by performing basic validation and sanity checks, at the sender, of the counter or timestamp fields in received measurement response messages. The minimal state associated with these protocols also limits the extent of measurement disruption that can be caused by a corrupt or invalid message to a single query/response cycle. Use of HMAC-SHA-256 in the authenticated mode protects the data integrity of the probe messages. SRv6 has HMAC protection authentication defined for SRH [RFC8754]. Hence, PM probe messages for SRv6 may not need authentication mode. Cryptographic measures may be enhanced by the correct configuration of access-control lists and firewalls. 9. IANA Considerations This document does not require any IANA action. 10. References 10.1. Normative References [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, DOI 10.17487/RFC0768, August 1980, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4656] Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M. Zekauskas, "A One-way Active Measurement Protocol (OWAMP)", RFC 4656, DOI 10.17487/RFC4656, September 2006, . [RFC5357] Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J. Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)", RFC 5357, DOI 10.17487/RFC5357, October 2008, . Gandhi, et al. Expires September 24, 2020 [Page 22] Internet-Draft TWAMP Light for Segment Routing March 2020 [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [I-D.ietf-6man-spring-srv6-oam] Ali, Z., Filsfils, C., Matsushima, S., Voyer, D., and M. Chen, "Operations, Administration, and Maintenance (OAM) in Segment Routing Networks with IPv6 Data plane (SRv6)", draft-ietf-6man-spring-srv6-oam-03 (work in progress), December 2019. 10.2. Informative References [IEEE1588] IEEE, "1588-2008 IEEE Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems", March 2008. [RFC2104] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed- Hashing for Message Authentication", RFC 2104, DOI 10.17487/RFC2104, February 1997, . [RFC2113] Katz, D., "IP Router Alert Option", RFC 2113, DOI 10.17487/RFC2113, February 1997, . [RFC4868] Kelly, S. and S. Frankel, "Using HMAC-SHA-256, HMAC-SHA- 384, and HMAC-SHA-512 with IPsec", RFC 4868, DOI 10.17487/RFC4868, May 2007, . [RFC5884] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow, "Bidirectional Forwarding Detection (BFD) for MPLS Label Switched Paths (LSPs)", RFC 5884, DOI 10.17487/RFC5884, June 2010, . [RFC6038] Morton, A. and L. Ciavattone, "Two-Way Active Measurement Protocol (TWAMP) Reflect Octets and Symmetrical Size Features", RFC 6038, DOI 10.17487/RFC6038, October 2010, . [RFC6335] Cotton, M., Eggert, L., Touch, J., Westerlund, M., and S. Cheshire, "Internet Assigned Numbers Authority (IANA) Procedures for the Management of the Service Name and Transport Protocol Port Number Registry", BCP 165, RFC 6335, DOI 10.17487/RFC6335, August 2011, . Gandhi, et al. Expires September 24, 2020 [Page 23] Internet-Draft TWAMP Light for Segment Routing March 2020 [RFC6437] Amante, S., Carpenter, B., Jiang, S., and J. Rajahalme, "IPv6 Flow Label Specification", RFC 6437, DOI 10.17487/RFC6437, November 2011, . [RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement for the Use of IPv6 UDP Datagrams with Zero Checksums", RFC 6936, DOI 10.17487/RFC6936, April 2013, . [RFC7506] Raza, K., Akiya, N., and C. Pignataro, "IPv6 Router Alert Option for MPLS Operations, Administration, and Maintenance (OAM)", RFC 7506, DOI 10.17487/RFC7506, April 2015, . [RFC7820] Mizrahi, T., "UDP Checksum Complement in the One-Way Active Measurement Protocol (OWAMP) and Two-Way Active Measurement Protocol (TWAMP)", RFC 7820, DOI 10.17487/RFC7820, March 2016, . [RFC8029] Kompella, K., Swallow, G., Pignataro, C., Ed., Kumar, N., Aldrin, S., and M. Chen, "Detecting Multiprotocol Label Switched (MPLS) Data-Plane Failures", RFC 8029, DOI 10.17487/RFC8029, March 2017, . [RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage Guidelines", BCP 145, RFC 8085, DOI 10.17487/RFC8085, March 2017, . [RFC8186] Mirsky, G. and I. Meilik, "Support of the IEEE 1588 Timestamp Format in a Two-Way Active Measurement Protocol (TWAMP)", RFC 8186, DOI 10.17487/RFC8186, June 2017, . [RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, July 2017, . [RFC8321] Fioccola, G., Ed., Capello, A., Cociglio, M., Castaldelli, L., Chen, M., Zheng, L., Mirsky, G., and T. Mizrahi, "Alternate-Marking Method for Passive and Hybrid Performance Monitoring", RFC 8321, DOI 10.17487/RFC8321, January 2018, . Gandhi, et al. Expires September 24, 2020 [Page 24] Internet-Draft TWAMP Light for Segment Routing March 2020 [RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L., Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing Architecture", RFC 8402, DOI 10.17487/RFC8402, July 2018, . [RFC8545] Morton, A., Ed. and G. Mirsky, Ed., "Well-Known Port Assignments for the One-Way Active Measurement Protocol (OWAMP) and the Two-Way Active Measurement Protocol (TWAMP)", RFC 8545, DOI 10.17487/RFC8545, March 2019, . [RFC8754] Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J., Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header (SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020, . [I-D.ietf-spring-segment-routing-policy] Filsfils, C., Sivabalan, S., Voyer, D., Bogdanov, A., and P. Mattes, "Segment Routing Policy Architecture", draft- ietf-spring-segment-routing-policy-06 (work in progress), December 2019. [I-D.voyer-spring-sr-replication-segment] Voyer, D., Filsfils, C., Parekh, R., Bidgoli, H., and Z. Zhang, "SR Replication Segment for Multi-point Service Delivery", draft-voyer-spring-sr-replication-segment-02 (work in progress), November 2019. [I-D.ietf-spring-mpls-path-segment] Cheng, W., Li, H., Chen, M., Gandhi, R., and R. Zigler, "Path Segment in MPLS Based Segment Routing Network", draft-ietf-spring-mpls-path-segment-02 (work in progress), February 2020. [I-D.ietf-spring-srv6-network-programming] Filsfils, C., Camarillo, P., Leddy, J., Voyer, D., Matsushima, S., and Z. Li, "SRv6 Network Programming", draft-ietf-spring-srv6-network-programming-14 (work in progress), March 2020. [BBF.TR-390] "Performance Measurement from IP Edge to Customer Equipment using TWAMP Light", BBF TR-390, May 2017. Gandhi, et al. Expires September 24, 2020 [Page 25] Internet-Draft TWAMP Light for Segment Routing March 2020 [I-D.gandhi-mpls-ioam-sr] Gandhi, R., Ali, Z., Filsfils, C., Brockners, F., Wen, B., and V. Kozak, "MPLS Data Plane Encapsulation for In-situ OAM Data", draft-gandhi-mpls-ioam-sr-02 (work in progress), March 2020. [I-D.ali-spring-ioam-srv6] Ali, Z., Gandhi, R., Filsfils, C., Brockners, F., Kumar, N., Pignataro, C., Li, C., Chen, M., and G. Dawra, "Segment Routing Header encapsulation for In-situ OAM Data", draft-ali-spring-ioam-srv6-02 (work in progress), November 2019. [I-D.ietf-pce-sr-bidir-path] Li, C., Chen, M., Cheng, W., Gandhi, R., and Q. Xiong, "PCEP Extensions for Associated Bidirectional Segment Routing (SR) Paths", draft-ietf-pce-sr-bidir-path-01 (work in progress), February 2020. Acknowledgments The authors would like to thank Thierry Couture for the discussions on the use-cases for Performance Measurement in Segment Routing. The authors would also like to thank Greg Mirsky for reviewing this document and providing useful comments and suggestions. Patrick Khordoc and Radu Valceanu, both from Cisco Systems have helped significantly improve the mechanisms defined in this document. The authors would like to acknowledge the earlier work on the loss measurement using TWAMP described in draft-xiao-ippm-twamp-ext- direct-loss. Authors' Addresses Rakesh Gandhi (editor) Cisco Systems, Inc. Canada Email: rgandhi@cisco.com Clarence Filsfils Cisco Systems, Inc. Email: cfilsfil@cisco.com Gandhi, et al. Expires September 24, 2020 [Page 26] Internet-Draft TWAMP Light for Segment Routing March 2020 Daniel Voyer Bell Canada Email: daniel.voyer@bell.ca Mach(Guoyi) Chen Huawei Email: mach.chen@huawei.com Bart Janssens Colt Email: Bart.Janssens@colt.net Gandhi, et al. Expires September 24, 2020 [Page 27]