PPVPN Working Group Loa Andersson Internet-Draft Utfors AB Design team editor Expiration Date: December 2002 26 June, 2002 PPVPN L2 Framework Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026 [RFC2026]. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. For potential updates to the above required-text see: http://www.ietf.org/ietf/1id-guidelines.txt Summary for Sub-IP related Internet Drafts RELATED DOCUMENTS: This being a Layer 2 vpn framework document, almost every document that has been sent to the ppvpn working group is related, at least in that they address provider provisioned vpn's. Even more closely related are the documents that address L2 vpn's. The reference section includes a list of the document we found that most useful to illustrate the issues we discuss in this document. WHERE DOES IT FIT IN THE PICTURE OF THE SUB-IP WORK This ID is intended for the PPVPN WG. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 2] WHY IS IT TARGETED AT THIS WG(s) PPVPN deals with provider provisioned VPNs. This document provides and a framework and architecture for Layer 2 Provider Provisioned Virtual Private Network services, a class of Provider Provisioned Virtual Private Networks services. JUSTIFICATION This document is a framework for Layer 2 VPNs, one of the main topics on the PPVPN WG charter, and is considered instrumental in progressing the standards work within the PPVPN group. Abstract This document provides a framework for Layer 2 Provider Provisioned Virtual Private Networks (PPVPNs). This framework is intended to aid in standardizing protocols and mechanisms to support interoperable Layer 2 PPVPNs. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [RFC2119]. Contents 1. Introduction........................................................ 4 1.1 Objectives and Scope of the Document ............................ 4 1.2 Layer 2 Virtual Private Networks ................................ 5 1.3 Terminology ..................................................... 5 2. Models.............................................................. 6 2.1 Reference Model for VPWS ........................................ 6 2.2 Reference Model for VPLS ........................................ 6 2.3 Reference Model for distributed VPLS-PE or VPWS-PE.............. 7 2.4 VPWS-PE and VPLS-PE ............................................. 8 3. Functional Components of L2 VPN .................................... 8 3.1 Types of L2VPN................................................... 8 3.2 Generic L2VPN Transport Functional Components................... 10 3.3 VPWS............................................................ 20 3.4 VPLS............................................................ 26 3.5 IP-only LAN-like Service (IPLS) ................................ 32 4. Security Considerations ........................................... 33 4.1 System security ................................................ 33 4.2 Access Control.................................................. 33 INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 3] 4.3 Endpoint authentication ..................................... 33 4.4 Data Integrity............................................... 33 4.5 Confidentiality ............................................. 33 4.6 User data and Control data .................................. 33 5. References......................................................... 33 6. Acknowledgements .................................................. 36 7. Authors Contact ................................................... 37 INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 4] 1. Introduction 1.1 Objectives and Scope of the Document This document provides a framework for Layer 2 Provider Provisioned Virtual Private Networks (PPVPNs). This framework is intended to aid in standardizing protocols and mechanisms to support interoperable Layer2 PPVPNs. The PPVPN WG group works with both Layer 3 PPVPNs and Layer 2 PPVPNs. A framework for L3 VPNs is found in [L3VPN-FW]. This document provides the same type of framework for Layer 2 PPVPNs as the Layer 3 framework does for Layer 3 PPVPNs. The term "provider provisioned VPNs" refers to Virtual Private Networks (VPNs) for which the Service Provider (SP) participates in management and provisioning of the VPN. There are multiple ways in which a provider can participate in a VPN, and there are therefore multiple different types of PPVPNs. The framework document discusses Layer2 VPNs (as defined in section 1.2). It also describes technical issues related to VPNs in which the provider participates in provisioning for provider edge and customer edge devices. First, this document discusses reference models for Layer 2 PPVPNs. Then the functional components of Layer2 PPVPN operations are discussed. Specifically, this includes discussion of the technical issues, which are important in the design of standards and mechanisms for support of Layer 2 PPVPNs. Furthermore, technical aspects of Layer2 PPVPNs interworking is clarified. Finally, security issues as they apply to Layer2 PPVPNs are addressed. Requirements for Layer 3 VPNs are found in [L3VPN-REQ] and for Layer 2 VPNs, for VPLS and VPWS, in [L2VPN-REQ]. This document has "inherited" a substantial content from "An Architecture for L2VPNs" [L2VPN-ARCH]. This document does not make choices, and does not select any particular approach to support VPNs. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 5] 1.2 Layer 2 Virtual Private Networks As Layer 2 provider provisioned VPN solutions has attracted more and more interest, several solutions has been proposed to the PPVPN WG. This document addresses the generic components relevant for every Layer 2 VPN but will not make any recommendations on the relative merits of how the different components are implemented. In [ANDERSSON-METRICS] parameters and metrics that could be used to compare different Layer 2 VPN solutions and how they could be evaluated when a L2 VPN has to meet different set of requirements is discussed. The parameters to be considered in evaluating L2 VPN implementations in different environments are e.g. scaling, cost, inter-domain reachability, provisioning, flexibility, integration and migration from existing infrastructure and services, value-added services, cost, etc. Currently we see two kinds of services that a service provider could offer to a customer by means of Layer 2 VPNs. Virtual Private Wire Service(VPWS)and a Virtual Private LAN Service (VPLS). The possibility of an IP-only LAN-like Service (IPLS) is opened up, but is very much for future study. A VPWS is a VPN service that supplies a L2 point-to-point service. Being a point-to-point service where there are very few scaling issues with the service as such. Scaling issues might arise from the number of end- points that can be supported on a particular PE. A VPLS is an L2 service that in all respects emulates LAN across a Wide Area Network (WAN). Thus it also has all the scaling characteristics of a LAN. Other scaling issues might arise from the number of end-points that can be supported on a particular PE. 1.3 Terminology This document list some terms and concepts that are specific to the L2 VPN framework, terms and concepts generally applicable to the PPVPN area will be found in [ANDERSSON-TERM]. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 6] 2. Models 2.1 Reference Model for VPWS Attachment PSN Attachment Circuits tunnel Circuits + +-----+ pseudo +----- + | | wire | | | CE1 |--+ +--| CE2 | | | | +-----+ +-----+ +-----+ | | | +-----+ +----|---- | | P | | ----+----+ +----- + |VPWS\|---|-----|-----|/VPWS| | PE1 |===|=====|=====| PE2 | | /|---|-----|-----|\ | +-----+ +----|---- | | | | ----|----+ +----- + | | | +-----+ +-----+ +-----+ | | | | CE3 |--+ +--| CE4 | | | | | +-----+ +----- + 2.1.1 Entities in the VPWS reference model The P, PE (VPWS-PE) and CE devices and the PSN tunnel as defined in [ANDERSSON-TERM]. Attachment circuit and pseudo wire as discussed in section 3. The PE does a simple mapping between the PW and attachment circuit based on local information, i.e. the PW de-multiplexor and incoming/outgoing logical/physical port. 2.2 Reference Model for VPLS The following diagram shows a VPLS reference model where PE devices that are VPLS-capable provide a logical interconnect such that CE devices belonging to a specific VPLS appear to be connected by a single logical Ethernet bridge. A VPLS can contain a single VLAN or multiple, tagged VLANs. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 7] +-----+ +-----+ + CE1 +--+ +---| CE2 | +-----+ | ................... | +-----+ VPLS A | +----+ +----+ | VPLS A | |VPLS| |VPLS| | +--| PE |--Service--| PE |-+ +----+ Provider +----+ / . Backbone . \ - /\-_ +-----+ / . | . \ / \ / \ +-----+ + CE +--+ . | . +-- \ Access \----| CE | +-----+ . +----+ . | Network | +-----+ VPLS B .....|VPLS|........ \ / VPLS B | PE | ^ ------- +----+ | | | | | +-----+ | | CE3 | +-- Logical bridge +-----+ VPLS A This reference model is adapted from [L2VPN-REQ]. The only difference is that the VPLS-PE is explicitly named. 2.2.1 Entities in the VPLS reference model The PE (VPLS-PE) and CE devices are defined in [ANDERSSON-TERM]. 2.3 Reference Model for distributed VPLS-PE or VPWS-PE VPLS-PE/VPWS-PE Functionality . . . . . . . . . . . . . . . . . . . . . . . . +----+ . +----+ +----+ . . Service . | CE | --.--|u-pe| ----|n-pe|-.---. Provider . +----+ . +----+ +----+ . . Backbone . . . . . . . . . . . . . . . . . . . . . 2.3.1 Entities in the distributed VPLS-PE or VPWS-PE reference model A VPLS-PE or a VPWS-PE functionality may be distributed to more than one device. The device closer to the customer/user is called User facing PE INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 8] (U-PE) and the device closer to the core network is called Network facing PE (N-PE). For further discussion see section 3.4.3. The U-PE and N-PE are defined in [ANDERSSON-TERM]. 2.4 VPWS-PE and VPLS-PE The VPWS-PE and VPLS-PE are functionally very similar, the they both use forwarders to map attachment circuits to pseudo-wires. The only differences is that while the forwarder in a VPWS-PE does a one-to-one mapping between the attachment circuit and psedo-wire, the forwarder in a VPLS-PE is a Virtual Switching Instance (VSI) that maps multiple attachment circuits to multiple pseudo-wires (for further discussion see section 3.) 3. Functional Components of L2 VPN This section specifies a functional model for L2VPN, which allows one to break an L2VPN architecture down into its functional components. This allows us to exhibit the roles played by the various protocols and mechanisms, and thus to make it easier to understand the differences and similarities between various proposed L2VPN architectures. Section 3.1 contains an overview of some different types of L2VPN. In section 3.2, functional components that are common to the different types are discussed. Then there is a section for each of the L2VPN service types being considered. The latter sections discuss functional components, which may be specific to particular L2VPN types, as well as discussing type-specific features of the generic components. 3.1 Types of L2VPN The types of L2VPN are distinguished by the characteristics of the service that they offer to the customers of the Service Provider (SP). 3.1.1 Virtual Private Wire Service (VPWS) In a VPWS, each CE device is presented with a set of point-to-point virtual circuits. The other end of each virtual circuit is another CE device. Frames transmitted by a CE on such a virtual circuit are received by the CE device at the other end-point of the virtual circuit. Forwarding from one CE device to another is not affected by the content of the frame, INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 9] but is fully determined by the virtual circuit on which the frame is transmitted. The PE thus acts as a virtual circuit switch. This type of L2VPN has long been available over ATM and Frame Relay backbones. Providing this type of L2VPN over MPLS and/or IP backbones is the current topic. Requirements for this type of L2VPN are specified in [L2VPN-REQ]. 3.1.2 Virtual Private LAN Service (VPLS) In a VPLS, each CE device has one or more LAN interfaces that lead to a "virtual backbone". Two CEs are connected to the same virtual backbone if and only if they are members of the same VPLS instance (i.e., same VPN). When a CE transmits a frame, the PE that receives it examines the MAC Destination Address field in order to determine how to forward the frame. This is determined using standard LAN bridging techniques, such as MAC Source Address Learning. (Thus unlike VPWS, VPLS allows the use of addressing information in a frame's L2 header to determine the CE to which a frame should be sent.) This allows a LAN to be extended transparently over an MPLS and/or IP backbone. VPLS is like VPWS in that forwarding is done without any consideration of the Layer3 header. Unlike VPWS, VPLS allows a single CE/PE connection to be used for transmitting frames to multiple remote CEs. In this respect, VPLS is more like L3VPN. Requirements for this type of L2VPN are specified in [L2VPN-REQ]. 3.1.3 IP-only LAN-like Service (IPLS) An IPLS is very like a VPLS, except that: - it is assumed that the CE devices are hosts or routers, not switches - it is assumed that the service will only carry IP packets, and supporting packets such as ICMP and ARP; Layer2 packets which do not contain IP are not supported. While this service is a functional subset of the VPLS service, it is considered separately because it may be possible to provide it using different mechanisms, which may allow it to run on certain hardware platforms that cannot support the full VPLS functionality. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 10 ] 3.2 Generic L2VPN Transport Functional Components All L2VPN types must transport "frames" across the core network connecting the PE's. In all L2VPN types, a PE (PE1) receives a frame from a CE (CE1), then transports the frame to a PE (PE2), which then transports the frame to a CE (CE2). In this section, we discuss the functional components, which are necessary to transport L2 frames in any type of L2VPN service. 3.2.1 Attachment Circuits In any type of L2VPN, a CE device attaches to a PE device via some sort of circuit or virtual circuit. We will call this an "Attachment Circuit" (AC). We use this term very generally; an Attachment Circuit may be a Frame Relay DLCI, an ATM VPI/VCI, an Ethernet port, a VLAN, a PPP connection on a physical interface, a PPP session from an L2TP tunnel, an MPLS LSP, etc. The CE device may be a router, a switch, a host, or just about anything, which the customer needs hooked up to the VPN. An AC carries a frame between CE and PE, or vice versa. Procedures for setting up and maintaining the ACs are out of scope of this architecture. These procedures are generally specified as part of the specification of the particular Attachment Circuit technology. Any given frame will traverse an AC from a CE to a PE and then on another AC from a PE to a CE. We refer to the former AC as the frame's "ingress AC" and to the latter AC as the frame's "egress AC". Note that this notion of "ingress AC" and "egress AC" is relative to a specific frame, and denotes nothing more than the frame's direction of travel while on that AC. 3.2.2 Pseudowires A "Pseudowire" (PW) is a relation between two PE devices. Whereas an AC is used to carry a frame from CE to PE, a PW is used to carry a frame between two PEs. We use the term "pseudowire" in the sense of [PWE3- FW]. Setting up and maintaining the PWs is the job of the PEs. State information for a particular PW is maintained at the two PEs which are its endpoints, but not at other PEs, and not in the backbone routers (P routers). Pseudowires may be point-to-point, multipoint-to-point, or point-to- multipoint. In this framework, point-to-point PWs are always considered INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 11 ] to be bidirectional; multipoint-to-point and point-to-multipoint PWs are always considered to be unidirectional. Multipoint-to-point PWs can be used only when the PE receiving a frame from the PW does not need to know where the frame came from. Point-to-multipoint PWs may be useful when frames need to be multicast. Procedures for setting up and maintaining point-to-multipoint PWs are not considered in this version of this framework. Any given frame travels first on its ingress AC, then on a PW, then on its egress AC. Multicast frames may be replicated by a PE, so of course the information carried in multicast frames may travel on more than one PW and more than one egress AC. Thus with respect to a given frame, a PW may be said to associate a number of ACs. If these ACs are of the same technology (e.g., both ATM, both Ethernet, both Frame Relay) the PW is said to provide "homogeneous transport"; otherwise it is said to provide "heterogeneous transport". Heterogeneous transport requires that some sort of interworking function be applied. There are at least three different approaches to interworking: 1. One of the CEs may perform the interworking locally. For example, if CE1 attaches to PE1 via ATM, but CE2 attaches to PE2 via Ethernet, then CE1 may decide to send/receive Ethernet frames over ATM, using the RFC2684 "LLC Encapsulation for Bridged Protocols". In such a case, PE1 would need to know that it is to terminate the ATM VC locally, and only send/receive Ethernet frames over the PW. 2. One of the PEs may perform the interworking. For example, if CE1 attaches to PE1 via ATM, but CE2 attaches to PE2 via Frame Relay, PE1 may provide the "ATM/FR Service Interworking" function. This would be transparent to the CEs, and the PW would carry only Frame Relay frames. 3. IPLS could be used. In this case the "frames" carried by the PW are IP datagrams, and the two PEs need to cooperate in order to spoof various L2-specific procedures used by IP (see section 3.5). 3.2.3 Forwarders In all types of L2VPN, a PE, say PE1, receives a frame over an AC, and forwards it over a PW to another PE, say PE2. PE2 then forwards the frame out on another AC. The case in which PE1 and PE2 are the same device is an important case to handle correctly, in order to provide the L2VPN service properly. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 12 ] However, as this case does not require any protocol, we do not further address it in this document. When PE1 receives a frame on a particular AC, it must determine the PW on which the frame must be forwarded. In general, this is done by considering: - the incoming AC, - possibly the contents of the frame's Layer2 header, and - possibly some forwarding information which may be statically or dynamically maintained. If dynamic or static forwarding information is considered, the information is specific to a particular L2VPN instance (i.e., to a particular VPN). Similarly, when PE2 receives a frame on a particular PW, it must determine the AC on which the frame must be forwarded. This is done by considering: - the incoming PW, - possibly the contents of the frame's Layer2 header, and - possibly some forwarding information which may be statically or dynamically maintained. If dynamic or static forwarding information is considered, the information is specific to a particular L2VPN instance (i.e. to a particular VPN). The procedures used to make the forwarding decision are known as a "forwarder". We may think of a PW as being "bound", at each of its endpoints, to a forwarder. The forwarder in turn "binds" the PWs to ACs. Different types of L2VPN have different types of forwarders. For instance, a forwarder may bind a single AC to a single PW, ignoring all frame contents and using no other forwarding information. Or a forwarder may bind an AC to a set of PWs and ACs, moving individual frames from AC to PW, from a PW to an AC or from AC to AC by comparing information from the frame's Layer2 header to information in a forwarding database. This is discussed in more detail below, as we consider the different L2VPN types. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 13 ] 3.2.4 Tunnels A PW is carried in a "tunnel" from PE1 to PE2. We assume that an arbitrary number of PWs may be carried in a single tunnel; the only requirement is that the PWs all terminate at PE2. We do not even require that all the PWs in the tunnel originate at PE1; the tunnels may be multipoint -to-point tunnels. Nor do we require that all PWs between the same pair of PEs travel in the same tunnel. All we require is that when a frame traveling through such a tunnel arrives at PE2, PE2 will be able to associate it with a particular PW. (While one can imagine tunneling techniques that only allow one PW per tunnel, they have evident scalability problems, and we do not consider them further.) There are a variety of different tunneling technologies which may be used for the PE-PE tunnels. All that is really required is that the tunneling technologies allow the proper demultiplexing of the contained PWs. The tunnels might be MPLS LSPs, L2TP tunnels, IPsec tunnels, MPLS- in-IP tunnels, etc. Generally the tunneling technology will require the use of an encapsulation that contains a demultiplexor field, where the demultiplexor field is used to identify a particular PW. Procedures for setting up and maintaining the tunnels are not within the scope of this framework. (But see section 3.2.6, "Pseudowire Signaling".) If there are multiple tunnels from PE1 to PE2, it may be desirable to assign a particular PE1-PE2 PW to a particular tunnel based on some particular characteristics of the PW and/or the tunnel. For example, perhaps different tunnels are associated with different QoS characteristics, and different PWs require different QoS. Procedures for specifying how to assign PWs to tunnels are out of scope of the current framework. Though point-to-point PWs are bidirectional, the tunnels in which they travel need not be either bidirectional or point-to-point. For example, a point-to-point PW may travel within a unidirectional multipoint -to- point MPLS LSP. 3.2.5 Encapsulation As L2VPN packets are carried in pseudowires, standard pseudowire encapsulation formats and techniques (as specified by the IETF's PWE3 WG) should be used wherever applicable. Generally the PW encapsulations will themselves be encapsulated within a tunnel encapsulation, as determined by the specification of the tunneling protocol. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 14 ] It may be necessary to define additional PW encapsulations to cover areas that are of importance for L2VPN, but may not be within the scope of PWE3. Heterogeneous transport may be an instance of this. 3.2.6 Pseudowire Signaling. Procedures for setting up and maintaining the PWs themselves are within the scope of this framework. This includes procedures for distributing demultiplexor field values, even though the demultiplexor field, strictly speaking, belongs to the tunneling protocol rather than to the PW. The signaling for a point-to-point pseudowire must perform the following functions: - Distribution of the demultiplexor. Since many PWs may be carried in a single tunnel, the tunneling protocol must assign a demultiplexor value to each PW. These demultiplexors must be unique with respect to a given tunnel (or with some tunneling technologies, unique at the egress PE). Generally, the PE which is the egress of the tunnel will select the demultiplexor values, and will distribute them to the PE(s) which is (are) the ingress(es) of the tunnel. This is the essential part of the PW setup procedure. Note that, as is usually the case in tunneling architectures, the demultiplexor field belongs to the tunneling protocol, not to the protocol being tunneled. For this reason, the PW setup protocols may be extensions of the control protocols for setting up the tunnels. - Selection of the Forwarder at the Remote PE. The signaling protocol must contain enough information to enable the remote PE to select the proper forwarder to which the PW is to be bound. We can call this information the "Remote Forwarder Selector". The information that is required will depend on the type of L2VPN being provided and on the provisioning model (see sections 3.3.1 and 3.4.1) being used. The Remote Forwarder Selector may uniquely identify a particular Forwarder, or it may identify an attribute of Forwarders. In the latter case, it would select whichever Forwarder has been provisioned with that attribute. - Support pseudowire emulations. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 15 ] To the extent that a particular PW must emulate the signaling of a particular Layer2 technology, the PW signaling must provide the necessary functions. - Distribution of State Changes. Changes in the state of an AC may need to be reflected in changes to the state of the PW to which the AC is bound, and vice versa. The specification as to which changes need to be reflected in what way would generally be within the province of the PWE3 WG. - Establish pseudowire characteristics. To the extent that one or more characteristics of a PW must be known to and/or agreed upon by both endpoints, the signaling must allow for the necessary interaction. As specified above, signaling for point-to-point PWs must pass enough information to allow a remote PE to properly bind a PW to a Forwarder, and to associate a particular demultiplexor value with that PW. Once the two PEs have done the proper PW/Forwarder bindings, and have agreed on the demultiplexor values, the PW may be considered to have been set up. If it is necessary to negotiate further characteristics or parameters of a particular PW, or to passing status information for a particular PW, the PW may be identified by the demultiplexor value. Signaling procedures for point-to-point pseudowires are most commonly point-to-point procedures that are executed by the two PW endpoints. There are however proposals to use point-to-multipoint signaling for setting up point-to-point pseudowires, so this is included in the framework. When PWs are themselves point-to-multipoint, it is also possible to use either point-to-point signaling or point-to-multipoint signaling to set them up. This is discussed in the remainder of this section. 3.2.6.1 Point-to-Point Signaling There are several ways to do the necessary point-to-point signaling. Among them are: - LDP LDP extensions can be defined for pseudowire signaling. See for example [MARTINI-SIGNALING], [ROSEN-L2-SIGNALING]. This form of signaling can be used for pseudowires which are to be carried in MPLS "tunnels", or in MPLS-in-something -else tunnels (e.g., [MPLS-IP], [MPLS-GRE]). INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 16 ] - L2TP L2TP [L2TP-BASE] can be used for pseudowire signaling, resulting in pseudowires that are carried as "sessions" within L2TP tunnels Pseudowire-specific extensions to L2TP may also be needed, e.g., see [L2TP-FR]. Other methods may be possible as well. It is possible to have one control connection between a pair of PEs, which is used to control many PWs. The use of point-to-point signaling for setting up point-to-point PWs is straightforward. Multipoint-to-point PWs can also be set up by point- to-point signaling, as the remote PEs do not necessarily need to know whether the PWs are multipoint-to-point or point-to-point. In some signaling procedures, the same demultiplexor value may be assigned to all the remote PEs. 3.2.6.2 Point-to-Multipoint Signaling Consider the following situation: - It is necessary to set up a set of PWs, all of which have the same characteristics. - It is not necessary to use the PW signaling protocol to pass PW state changes. - For each PW in the set, the same value of the Remote Forwarder Selector can be used. Call these the "Environmental Conditions". Suppose also that there is some mechanism by which, given a range of demultiplexor values, each of a set of PEs can make a unique and deterministic selection of a single value from within that range. Call this the "Demultiplexor Condition". Alternatively, suppose that one is trying to set up a multipoint -to-point PW rather than a point-to-point PW. Call this the "Multipoint Condition". If: - The Environmental Conditions hold, and - Either * the Demultiplexor Condition holds, or INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 17 ] * the Multipoint Condition holds, then for a given set of PWs which terminate at egress PE1, the information which PE1 needs to send to the ingress PE(s) of each pseudowire in the set is exactly the same. All the ingress PE(s) receive the same Forwarder Selector value. They all receive the same set of PW parameters (if any). And either they all receive the same demultiplexor value (if the PW is multipoint-to-point) or they all receive a range of demultiplexor values from which each can choose a unique demultiplexor value for itself. Rather than connecting to each ingress PE and replicating the same information, it may make sense either to multicast the information, or to send the information once to a "reflector", which will then take responsibility for distributing the information to the other PEs. We refer to this sort of technique as "point-to-multipoint" signaling. It would, for example, be possible to use BGP to do the signaling, with the PEs being BGP peers not of each other, but of one or more BGP route reflectors. Such a scheme, based Multi-protocol Extensions to BGP, is proposed in [KOMPELLA-L2VPN]. 3.2.6.3 Inter-AS Considerations Pseudowires may need to run from a PE in one Service Provider's network to a PE in another Service Provider's network. This means that the signaling to set up the PEs must be able to cross network boundaries. All known proposals for signaling are able to do this. It is especially advisable to use some form of authentication between the two PW endpoints in this case. 3.2.7 Service Quality Service Quality refers to the ability for the network to deliver a Service level Specification (SLS) for service attributes such as protection, security and Quality of Service (QoS). The service quality provided depends on the subscriber's requirements, and can be characterized by a number of performance metrics. The necessary Service Quality must be provided on the ACs as well as on the PWs. Mechanisms for providing Service Quality on the PWs may be PW- specific or tunnel-specific; in the latter case, the assignment of a PW to a tunnel may depend on the Service Quality. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 18 ] 3.2.7.1 Quality of Service (QoS) QoS describes the queuing behavior applied to a particular "flow", in order to achieve particular goals of precedence, throughput, delay, jitter, etc. Based on the customer Service Level Agreement (SLA), traffic from customer can be prioritized, policed and shaped for QoS requirements. The queuing and forwarding po licies can preserve the packet order and QoS parameters of customer traffic. The class of services can be mapped from information in the customer frames, or it can be independent of the frame content. QoS functions can be listed as follows: - Customer Traffic Prioritization: L2VPN services could be best effort or QoS guaranteed. Traffic from one customer might need to be prioritized over others when sharing same network resources. This requires capabilities within the L2VPN solution to classify and mark priority to QoS guaranteed customer traffic. Proper queuing behavior would be needed at the egress AC, and possibly within the backbone network as well. If queuing behavior must be controlled within the backbone network, the control might be based on CoS information in the MPLS or IP header, or it might be achieved by nesting particular tunnels within particular traffic engineering tunnels. Policing: This ensures that a user of L2VPN services uses network resources within the limits of the agreed SLA. Any excess L2VPN traffic can be rejected or handled differently based on provider policy. Policing would generally be applied at the ingress AC. Shaping: Under some cases the random nature of L2VPN traffic might lead to sub-optimal utilization of network resources. Through queuing and forwarding mechanisms the traffic can be shaped without altering the packet order. Shaping would generally be applied at the ingress AC. 3.2.7.2 Resiliency Resiliency describes the ability of the L2VPN infrastructure to protect a flow from network outage, so that service remains available in the presence of failures. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 19 ] L2VPN, like any other service, is subject to failures such as link, trunk and node failures, both in the SP's core network infrastructure and on the ACs. It is desirable that the failure be detected "immediately" and protection mechanisms allow fast restoration times to make L2VPN service almost transparent to these failures to the extent possible, based on the level of resiliency. Restoration should take place before the CEs can react to the failure. Essential aspects of providing resiliency are: - Link/Node failure detection: Mechanisms within the L2VPN service should allow for link or node failures that impact the Service, and should be detected immediately. - Resiliency policy: The way in which a detected failure is handled will depend upon the restoration policy of the SLA associated with the L2VPN service specification. It may need to be handled immediately, or it may need to be handled only if no other critical failure needs protection resources, or it may be completely ignored if it is within the bounds of the "acceptable downtime" allowed by the L2VPN service. - Restoration Mechanisms: The L2VPN solutions could allow for physical level protection, logical level protection or both. For example, by connecting customers over redundant and physically separate ACs to different provider customer-facing devices, one AC can be maintained as active while the other could be marked as a backup; upon the failure detection across the primary AC, the backup could become active. To a great extent, resiliency is a matter of having appropriate failure and recovery mechanisms in the network core, including "ordinary" adaptive routing as well as "fast reroute" [???] capabilities. The ability to support redundant ACs between CEs and PEs also plays a role. 3.2.8 Management An L2VPN solution can provide mechanisms to manage and monitor different L2VPN components. From a Service Level Agreement (SLA) perspective, L2VPN solutions could allow monitoring of L2VPN service characteristics and offer mechanisms used by Service Providers to report such monitored statistical data. Trouble-shooting and verification of operational and maintenance activities of L2VPN services are essential requirements for Service Providers. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 20 ] 3.3 VPWS A VPWS is an L2VPN service in which each forwarder binds exactly one AC to exactly one PW. Frames received on the AC are transmitted on the PW; frames received on the PW are transmitted on the AC. The content of a frame's Layer2 header plays n o role in the forwarding decision, except insofar as the Layer2 header contents are used to associate the frame with a particular AC (as, e.g., the DLCI field of a Frame Relay frame identifies the AC). A particular combination of forms a "virtual circuit" between two CE devices. A particular VPN (VPWS instance) may be thought of as a collection of such virtual circuits, or as an "overlay" of PWs on the MPLS or IP backbone. This creates an overlay topology that is in effect the "virtual backbone" of a particular VPN. Whether two virtual circuits are said to belong to the same VPN or not is an administrative matter, based on the agreements between the SPs and their customers. This may impact the provisioning model (discussed below). It may also affect how particular PWs are assigned to tunnels, the way QoS is assigned to particular ACs and PWs, etc. Note that VPWS makes use of point-to-point PWs exclusively. VPWS solutions are found e.g. in [DIRLDP], [KOMPELLA-L2VPN] and [ROSEN- L2-SIGNALING]. 3.3.1 Provisioning and Auto-Discovery Provisioning a VPWS is a matter of: 1. Provisioning the ACs 2. Providing the PEs with the necessary information to enable them to set up PWs between ACs to result in the desired overlay topology. 3. Configuring the PWs with any necessary characteristics 3.3.1.1 Attachment Circuit Provisioning In many cases, the ACs must be individually provisioned on the PE and/or CE. This will certainly be the case if the CE/PE attachment technology is a switched network, such as ATM or FR, and the VCs are PVCs rather than SVCs. It is also the case whenever the individual Attachment INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 21 ] Circuits need to be given specific parameters (e.g., QoS parameters, guaranteed bandwidth parameters) that differ from circuit to circuit. There are also cases in which ACs might not have to be individually provisioned. E.g., if an AC is just an MPLS LSP running between a CE and a PE, it could be set up as the RESULT of a PW being set up, rather than having to be provisioned BEFORE the PW can be set up. The same may apply whenever the AC is a Switched Virtual Circuit of any sort, though in this case, various policy controls might need to be provisioned, e.g., limiting the number of ACs that can be set up between a given CE and a given PE. Issues such as whether the Attachment Circuits need to be individually provisioned or not, whether they are Switched VCs or Permanent VCs, and what sorts of policy controls may be applied, are implementation and deployment issues, and are considered to be out of scope of this framework. 3.3.1.2 PW Provisioning for Arbitrary Overlay Topologies In order to support arbitrary overlay topologies, it is necessary to allow the provisioning of individual PWs. In this model, when a PW is provisioned on a PE device, it is locally bound to a specific AC. It is also provisioned with information that identifies a specific AC at a remote PE. There are basically two variations of this provisioning model: - Two-sided provisioning With two-sided provisioning, each PE that is at the end of a PW is provisioned with the following information: * Identifier of the Local AC to which the PW is to be bound * PW type and parameters * IP address of the remote PE (i.e., the PE which is to be at the remote end of the PW) * Identifier which is meaningful to the remote PE, and which can be passed in the PW signaling protocol to enable the remote PE to bind the PW to the proper AC. This can be an identifier of the pseudowire (as in [MARTINI-SIGNALING]), or an identifier of the remote AC (as in [ROSEN-L2-SIGNALING]). If a PW identifier is used, it must be unique at each of the INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 22 ] two PEs. If an AC identifier is used, it need only be unique at the remote PE. This identifier is then used as the Remote Forwarder Selector when signaling is done (see 3.2.6.1). - Single-sided Provisioning With single sided provisioning, a PE at one end of a PW is provisioned with the following information: * Identifier of the Local AC to which the PW is to be bound * PW type and parameters * Globally unique identifier of remote AC This identifier is then used as the Forwarder Selector when signaling is done (see section 3.2.6.1). In this provisioning model, the IP address of the remote PE is not provisioned. Rather, the assumption is that an auto- discovery scheme will be used to map the globally unique identifier to the IP address of the remote PE, along with an identifier (perhaps unique only at the latter PE) for an AC at that PE. The PW signaling protocol can then make a connection to the remote PE, passing the AC identifier, so that the remote PE binds the PW to the proper AC. (See, for example, [ROSEN-L2- SIGNALING].) This scheme requires provisioning of the PW at only one PE, but does not eliminate the need (if there is a need) to provision the ACs at both PEs. These provisioning models fit well with the use of point-to-point signaling. When each PW is individually provisioned, as the conditions necessary for the use of point-to-multipoint signaling do not hold. 3.3.1.3 Colored Pools PW Provisioning Model Suppose that at each PE, sets of ACs are gathered together into "pools", and that each such pool is assigned a "color". (For example, a pool might contain all and only the ACs from this PE to a particular CE.) Now suppose we impose the following rule: whenever PE1 and PE2 have a pool of the same color, there will be a PW between PE1 and PE2 which is bound at PE1 to an arbitrarily chosen AC from that pool, and at PE2 to INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 23 ] an arbitrarily chosen AC from that pool. (We do not rule out the case where a single PE has multiple pools of a given color.) For example, each pool in a particular PE might represent a particular CE device, with the ACs in the pool being the ACs connecting that CE to that PE. The color might be a VPN-id. Application of this provisioning model would then lead to a full CE-to-CE mesh within the VPN, where every CE in the VPN has a virtual circuit to every other CE within the VPN. More specifically, to provision VPWS according to this model, one provisions a set of pools, and configures each pool with the following information: - The set of ACs that belong to the pool (with no AC belonging to more than one pool) - The color - A pool identifier that is unique at least relative to the color. An auto-discovery procedure is then used to map each color into a list of ordered pairs . The occurrence of a pair on this list means that the PE at IP address X has a pool with pool id Y which is of the specified color. This information can be used to support several different signaling techniques. One possible technique proceeds as follows: - A PE finds that it has a pool of color C. - Using auto-discovery, it obtains the set of ordered pairs for color C. - For each such pair , it: * removes an AC from the pool * binds the AC to a particular PW * signals PE X via point-to-point signaling that the PW is to be bound to an AC from pool Y. This sort of technique is discussed in [ROSEN-L2-SIGNALING]. Another possible signaling technique is the following: INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 24 ] - A PE finds that it has a pool of color C, containing n ACs. - It binds each AC to a PW, creating a set of PWs. This set of PWs is then organized into a sequence. (For instance, each PW may be associated with a demultiplexor field value, and the PWs may then be sequenced according to the numerical value of their respective demultiplexors.) - Using auto-discovery, it obtains the list of PE routers that have one or more pools of color C. - It signals each such PE router, specifying the sequence Q of PWs. - If PE X receives such a signal, and PE X has a pool Y of the specified color, it: * removes an AC from the pool * binds the AC to the PW which is the "Yth" PW in the sequence Q. This presumes, of course, that the pool identifiers are or can be uniquely mapped into small ordinal numbers; assigning the pool identifiers in this way becomes a requirement of the provisioning system. Note that since this technique signals the same information to all the remote PEs, it can be supported via point-to-multipoint signaling. This sort of scheme is discussed in [KOMPELLA-L2VPN]. This provisioning model can be applied as long as the following conditions hold: - There is no need to provision different characteristics for the different PWs, and - It makes no difference which pairs of ACs are bound together by PWs, as long as both ACs in the pair come from like-colored pools, and - It is possible to construct the desired overlay topology simply by assigning colors to the pools. (This is certainly simple if a full mesh is desired, or if a hub and spoke configuration is desired; creating arbitrary topologies is less simple, and perhaps not always possible.) INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 25 ] 3.3.2 Requirements on Auto-Discovery Procedures Some of the requirements for auto-discovery procedures can be deduced from the above. To support the single-sided provisioning model, auto-discovery must be able to map a globally unique identifier (of a PW or of an Attachment Circuit) to an IP address of a PE. To support the colored pools provisioning model, auto-discovery must enable a PE to determine the set of other PEs that contain pools of the same color. Examples of suitable auto-discovery procedures can be found in Examples of suitable auto-discovery procedures can be found in [KOMPELLA-L2VPN], [BGP-AUTO] and [ROSEN-L2-SIGNALING], and [DNS-LDP-VPLS]. These requirements enable the auto-discovery scheme to provide the information, which the PEs need to set up the PWs. There are additional requirements on the auto-discovery procedures that cannot simply be deduced from the provisioning model: - Particular signaling schemes may require additional information before they can proceed, and hence may impose additional requirements on the auto-discovery procedures. - A given Service Provider may support several different types of signaling procedures, and thus the PEs may need to learn, via auto- discovery, which signaling procedures to use. - Changes in the configuration of a PE should be reflected by the auto-discovery procedures, within a timely manner, and without the need to explicitly reconfigure any other PE. - The auto-configuration procedures must work across service provider boundaries. This rules out, e.g., the use of schemes that piggyback the auto-discovery information on the backbone's IGP. 3.3.3 Heterogeneous Pseudowires Under certain circumstances, it may be desirable to have a PW that binds two ACs that use different technologies (e.g., one is ATM, one is Ethernet). There are a number of different ways, depending on the AC types, in which this can be done. For example: - If one AC is ATM and one is FR, then standard ATM/FR Network Interworking can be used. In this case, the PW might be signaled INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 26 ] for ATM, with the Interworking function occurring between the PW and the FR AC. - A common encapsulation can be used on both ACs, e.g., if one AC is Ethernet and one is FR, an "Ethernet over FR" encapsulation can be used on the latter. In this case, the PW could be signaled for Ethernet, with the processing of the Ethernet over FR encapsulation being local to the PE with the FR AC. - If it is known that the two ACs attach to IP routers or hosts, and carry only IP traffic, then one could use a PW which carries the IP packets, and the respective Layer2 encapsulations would be local matters for the two PEs. However, if one of the ACs is a LAN and one is a point-to-point link, care would have to be taken to ensure that such procedures as ARP and Inverse ARP are properly handled; this might require some signaling, and some proxy functions. Further, if the CEs use a routing algorithm that has different procedures for LAN interfaces than for point-to-point interfaces, additional mechanisms may be required to ensure proper interworking. These issues are discussed in Fel! Hittar inte referensk„lla.. 3.4 VPLS A VPLS is an L2VPN service in which: - The Forwarders bind multiple ACs to multiple PWs - Each Forwarder behaves as a "Virtual Switch Instance" (VSI), which performs standard LAN (i.e., Ether net) bridging functions. These include maintenance of a forwarding table by means of MAC address learning, and broadcasting of frames with unknown MAC Destination Addresses. An AC connects a CE to a VSI. Multiple CEs may be connected to a single VSI. The payload on the ACs must be Ethernet frames, with or without VLAN headers. An AC may run over any medium that can carry Ethernet frames, either natively or in some encapsulation. The set of VSIs within a single VPLS are connected via PWs; two VSIs will have a PW between them only if those two VSIs are part of the same VPN. There may be a further restriction that two VSIs have a PW between them only if those two VSIs are part of the same VLAN in the same VPN. When the CE device is itself a LAN switch, the VSI may or may not be visible as a LAN switch to the CE. That is, it may send and receive BPDUs to and from the CE, or it may simply pass a CE's BPDUs to the INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 27 ] other CEs, without ever sending a BPDU of its own to the CE. Different VPLS solutions may differ in this respect. VPLS solutions are found e.g. in [DNS-LDP-VPLS], [LASSERRE-VKOMPELLA- VPLS] and [KOMPELLA-VPLS]. 3.4.1 VPLS Overlay Topologies and Forwarding A VPLS emulates a LAN, in that all frame forwarding decisions are based only on the frame's MAC Destination Address (DA), the frame's "incoming port", and the contents of the forwarding table. For this purpose, both PWs and ACs are considered to be ports. The VSI forwarding decision maps a MAC DA and incoming port to an outgoing port. In order to use MAC address learning to populate the forwarding table, the PWs must be point-to-point or point-to-multipoint PWs. (Point -to- multipoint PWs may be useful when it is necessary to multicast a frame; the alternative would be replication of the frame by the PE, and transmission of each replica over a set of point-to-point PWs.) There is no use for multipoint-to-point PWs. MAC learning over a point-to-point PW is done via standard techniques, considering the PW to be a port. But MAC addresses learned over a point-to-multipoint PW whose root is PE1 would have to be treated as if they had been learned over the point-to-point PW which comes from PE1. The VSI forwarding decisions must be coordinated so that loop-free forwarding over the overlay topology is ensured. There are several possible types of overlay topologies: - Full mesh In a full mesh, every VSI in a given VPLS has exactly one point- to-point PW to every other VSI in that same VPLS. In this topology, loop free forwarding of frames is ensured by the following rule: if a frame is received over a PW, do not forward it over ANY other PW. Multicast and unknown DA packets are replicated and sent over all ports other than the one from which they were received. Alternatively, the full mesh of point-to-point PWs may be augmented with point-to-multipoint PWs, where each VSI in a VPLS is the transmitter on a single point-to -multipoint PW, and the receivers on that PW are all the other VSIs in that VPLS. - Tree Structured INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 28 ] In a tree structured topology, every VSI in a particular VPLS is provisioned to be at a particular level in the tree. A given VSI has at most one pseudowire leading to a higher level. The root of the tree is considered to be the highest level. In this topology, loop free forwarding of frames is ensured by the following rule: if a frame is received over a pseudowire from a higher level, it may not be sent over a pseudowire that leads to a higher level. - Tree with Meshed Highest Level In this variant of the tree-structured topology, there may be more than one VSI at the highest level, but the set of VSIs which are at the highest level must be fully meshed. To ensure loop free forwarding, we need to impose the rule that a frame can be sent on a pseudowire to the same or higher level only if it arrived over a pseudo wire from a lower level, and frames arriving over PWs from the same level cannot be sent on PWs to the same level. Other overlay topologies are also possible, e.g., an arbitrary partial mesh of PWs among the VSIs of a VPLS. Loop-freedom could then be assured by, for example, running spanning tree on the overlay. These topologies are not further considered in this framework. Note that loop freedom in the overlay topology does not necessarily ensure loop freedom in the overall customer LAN that contains the VPLS. Improper configuration of the customer LAN (outside the limits of the VPLS) may cause looping, and frames that fall into such loops may transit the overlay topology multiple times. Procedures that enable the PE to detect and/or prevent such loops may be advisable. 3.4.2 Provisioning and Auto-Discovery Each VPLS must be assigned a globally unique identifier. This can be thought of as a VPN-id. The ACs attaching the CEs to the PEs must be provisioned on both the PEs and the CEs. A VSI for that VPLS must be provisioned on the PE, and the local ACs of that VPLS must be associated with that VSI. The VSI must be provisioned with the identifier of the VPLS to which it belongs. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 29 ] An auto-discovery scheme may be used by a PE to map a VPLS identifier into the set of remote PEs that have VSIs in that VPLS. Once this set is determined, the PE can use pseudowire signaling to set up a PW to each of those VSIs. The VPLS identifier would serve as the signaling protocol's Forwarder Selector. This would result in a full mesh of PWs among the VSIs in a particular VPLS. If a single VPLS contains multiple VLANs, then it may be desirable to limit connectivity so that two VSIs are connected only if they have a VLAN in common. In this case, each VSI would need to be provisioned with one or more VLAN ids, and the auto-discovery scheme would need to map a VPLS identifier into pairs of . If a fully meshed topology of VSIs is not desired, then each VSI needs to be provisioned with additional information specifying its placement in the topology. This information would also need to be provided by the auto-discovery scheme. Examples of suitable auto-discovery procedures can be found in [KOMPELLA-L2VPN], [BGP-AUTO] and [ROSEN-L2-SIGNALING], and [DNS-LDP- VPLS]. Alternatively, the single-sided provisioning method discussed in section 3.3.1.2 could be used. As this is more complicated, it would only be used if it were necessary to associate individual PWs with individual characteristics. For example, if different guaranteed bandwidths were needed between different pairs of sites within a VPLS, the PWs would have to be individually provisioned. 3.4.3 Distributed PE Often when a VPLS type of service is provided, the CE devices attach to a provider-managed CPE device. This provider-managed CPE device may attach to CEs of multiple customers, especially if, e.g., there are multiple customers occupying the same building. However, this device is really part of the SP's network, hence may be considered to be a PE device. In some scenarios when a VPLS type of service is provided, the CE devices attach to a provider-managed intermediary device. This provider- managed device may attach to CEs of multiple customers. This may arise in a situation there multiple customers occupying the same building. This device is really part of the SP's network, and may for that reason be considered to be a PE device, however in the simplest case it is only performing aggregation and none of the function associated with a VPLS. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 30 ] Relative to the VPLS there are three different possibilities to allocate functions to a device in such a position in the provider network: - it can perform aggregation and pure Layer2 service only, in which case it does not really play the role of a PE device in a VPLS service. In this case the intermediary system must connect to devices that perform VPLS PE functionality; the intermediary device itself is not part of the VPLS architecture and has hence not been named in this architecture. - it can perform all the PE functions relevant for a VPLS, in such a case the device is called VPLS-PE, see [ANDERSSON -TERM]. This type of device will be connected to the core (P) routers. The PE functionality for a VPLS may be distributed between two devices, one "low-end" closer to the customer that performs e.g. the MAC-address learning and forwarding decisions, and one "high-end" that performs the control functions, e.g. establishing tunnels, PWs and VCs. We call the low-end device User-Facing PE (U-PE) and the high-end device Network- Facing PE (N-PE). It is conceivable that the U-PE may be placed very close to the customer, e.g. in a building with more than one customer. In [KOMPELLA- DTLS], these are referred to as Multi-Tenant Units, but the resulting acronym is already used for something else. In [SAJASSI-VPLS] this type of device is called PE-CLE. [MOHAN-LPE] introduces another yet another naming scheme, the U-PE is called PE-Edge and the N-PE is called PE- Core. The N-PE, in [KOMPELLA-DTLS] called L2PE and in [SAJASSI-VPLS] called PE-POP, will presumably be placed on the SP's premises. The distributed case is potentially of interest for a number of possible reasons: - The N-PE may be a device that cannot easily implement the VSI functionality described above. E.g., perhaps the N-PE is a router which cannot perform the high speed MAC learning that is needed in order to implement a VSI forwarder. At the same time, the U-PE may need to be a low-cost device that also cannot implement the full set of VPLS functions. This leads one to investigate further if there are sensible ways to split the VPLS PE functionality between the U-PE and the N-PE. - Generally, in the L2VPN architecture, the PEs are expected to participate as peers in the backbone routing protocol. Since the number of U-PEs is potentially very large relative to the number of INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 31 ] N-PEs, this may be undesirable, as a matter of scaling the backbone routing protocol. - The U-PE may be a relatively inexpensive device that is unable to participate in the full range of signaling and/or auto-discovery procedures that are needed in order to provide the VPLS service. The VPLS functionality can be distributed between U-PE and N-PE in a number of different ways, and a number of different proposals have been made ([KOMPELLA-DTLS], [MOHAN -LPE], [SAJASSI-VPLS]). They all presume that the U-PE will maintain a VSI forwarder, connected by PWs to the remote VSIs; the N-PE thus does not need to perform the VSI forwarding function. The proposals tend to differ with respect to the following questions: - Should the U-PEs perform full PW signaling to set up the PWs to remote VSIs? Or should the N-PEs do this signaling? Since the U-PEs need to be able to send packets on PWs to remote VSIs and receive packets on PWs from remote VSIs, if the PW signaling is done by the N-PE, there would have to be some form of "lightweight" (presumably) signaling between N-PE and U-PE that allows the PWs to be extended from N-PE to U-PE. - Should the U-PEs do their own auto -discovery, or should this be done by the N-PEs? In the latter case, the U-PEs may need to have some means of telling the N-PEs which VPLS's they are interested in, and the N-PEs must have some means of passing the results of the auto-discovery process to the U-PE. Whether it makes sense to split auto-discovery in this manner may depend on the particular auto-discovery protocol used. One would not expect the U-PE to participate in BGP auto-discovery, e.g., but perhaps they would be expected to participate in DNS auto- discovery. - If a U-PE does not participate in routing, but is redundantly connected to two different N-PEs, can the U-PE still make an intelligent choice of the best N-PE to use as the "next hop" for traffic destined to a particular remote VSI? If not, can this choice be made as the result of some other sort of interaction between N-PE and U-PE? Or does this choice need to be established by provisioning? - If a U-PE does not participate in routing, but does participate in full PW signaling, and if MPLS is being used, how can the the N-PE send the the U-Pes the labels that the U-PE needs to send traffic INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 32 ] to its signaling peers. (If the U-PE did participate in routing, this would happen automatically.) - When a frame must be multicast, should the replication be done by the N-PE or the U-PE? These questions are not all independent; the way one answers some of them may influence the way one answers others. 3.4.4 Scaling issues in VPLS deployment In general, the PSN supports a VPLS solution with a tunnel from each VPLS-PE every other VPLS-PE participating in the same VPLS instance. Strictly, VPLS-PE's with more than one VPLS instance in common only need one tunnel, but for resource allocation reasons it might be necessary to establish several tunnels. For each VPLS service on a given VPLS-PE it needs to establish one pseudowire to every other VPLS-PE participating in that VPLS service. In total n*(n-1) pseudowires must be setup between the VPLS-PE routers. In large scale deployment this obviously creates scaling problems. An solution addressing the scaling problems was addressed in an Internet Draft by S Khandekar et.al. called "Hierarchical This has been addressed "Hierarchical Virtual Private LAN Service", this work has latter been included in [LASSERRE-VKOMPELLA- VPLS]. 3.5 IP-only LAN-like Service (IPLS) If, instead of providing a general VPLS service, one wishes to provide a VPLS that is used only to connect IP routers or hosts (i.e., the CE devices are all assumed to be IP routers or hosts), then it is possible to make certain simplifications. In this environment, all Ethernet frames sent from a particular CE to a particular PE on a particular Attachment Circuit will have the same MAC Source Address. Thus rather than using address learning in the data plane to learn the MAC addresses, the PE can use the control plane to learn the MAC address. (See Fel! Hittar inte referensk„lla. for a discussion of this.) This allows the PE to be implemented on devices that are not capable of doing MAC address learning in the data plane. To eliminate the need for MAC address learning on the PWs as well as on the ACs, the pseudowire signaling protocol would have to carry the MAC address from one pseudowire endpoint to the other. Each PE would perform proxy ARP to its directly attached CEs. Eliminating the need to do MAC address learning on the PWs eliminates the need for the PWs to be point-to-point. Multipoint-to-point PWs could be used instead. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 33 ] Unlike a VPLS, all the ACs in an IPLS would not necessarily have to carry Ethernet frames; only the IP packets would need to be passed across the network, not their Layer2 wrappers. However, this might require "translation" between "ARP" and "Inverse ARP". The set of routing protocols which could be carried across the IPLS might also be restricted. A fuller discussion of the advantages, disadvantages, and restrictions may be found in Fel! Hittar inte referensk„lla.. 4. Security Considerations Security considerations will be addressed in a future version of this document. 4.1 System security This is for a future version of this document. 4.2 Access Control This is for a future version of this document. 4.3 Endpoint authentication This is for a future version of this document. 4.4 Data Integrity This is for a future version of this document. 4.5 Confidentiality This is for a future version of this document. 4.6 User data and Control data This is for a future version of this document. 5. References [rfc2026] Bradner, S. "The Internet Standards Process -- Revision 3", RFC 2026, October 1996. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 34 ] [rfc2119] Bradner, S. "Key words for use in RFCs to Indicate Requirement Levels", RFC 2119, March 1997. [ANDERSSON-METRICS] Andersson, L. "Parameters and related metrics to compare PPVPN Layer 2 solutions", draft-andersson-ppvpn-metrics -00.txt, Work in Progrss, Internet Draft, Feb 2002. [ANDERSSON-TERM] Andersson, L. and Madsen T. "VPN Terminology", draft-andersson- ppvpn-terminology-00.txt", Work in Progress, Internet Draft, Feb 2002. [BGP-AUTO] Ould-Brahim, H. et.al. "Using BGP as an Auto-Discovery Mechanism for Network-based VPNs", Ould-Brahim et al, draft- ietf-ppvpn-bgpvpn-auto-01.txt, Work in Progress, Internet Draft, Nov 2001 [DIRLDP] Heinanen, J, "Directory/LDP Based Unidirectional Virtual Circuit VPNs" draft-heinanen-dirldp-uni-vc-vpns-01.txt, Work in Progress, Internet Draft, Nov 2001 [DNS-LDP-VPLS] Heinanen, J, "DNS/LDP Based VPLS", draft-heinanen -dns-ldp-vpls- 00.txt, Work in Progress, Internet Draft, Jan 2002 [KOMPELLA-DTLS] Kompella, K et.al. "Decoupled Virtual private LAN Services", draft-kompella-ppvpn-dtls-01.txt, December 2001 [KOMPELLA-L2VPN] Kompella, K. et.al. "Layer 2 VPNs Over Tunnels", draft- kompella-ppvpn-l2vpn-01.txt, Nov 2001 [KOMPELLA-VPLS] Kompella, K. "Virtual Private LAN Service", draft -kompella- ppvpn-vpls-00.txt, Work in Progress, Internet Draft, Nov 2001 [L2TP-BASE] Lau, J. "Layer Two Tunneling Protocol (Version 3) L2TPv3" draft-ietf-l2tpext-l2tp-base-02.txt", Work in Progress, Internet Draft, March 2002. [L2TP-FR] Townsley, W. M. et.al. ""Frame Relay Pseudowire Extensions for INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-00.txt 26.06.02 Andersson Expires Dec 2002 [Page 35 ] L2TP", draft-ietf-l2tpext-pwe3-fr-00.txt, Work in Progress, Internet Draft, Feb 2002. [L2VPN-ARCH] Rosen, E. et.al. "An Architecture for L2VPNs", draft-ietf- ppvpn-l2vpn-00.txt, Work in Progress, Internet Draft Jul 2001. [L2VPN-REQ] Augustyn, W. et.al "Requirements for Layer 2 Virtual Private Network Services (L2VPN)", draft-augustyn-ppvpn-l2vpn- requirements-00.txt, Work in Progress, Internet Draft, June 2002. [L3VPN-FW] Callon, R. et.al. "A Framework for Layer 3 Provider Provisioned Virtual Private Networks", draft-ietf-ppvpn-framework-05.txt, Work in Progress, Internet Draft, April 2002 [L3VPN-REQ] Carugi, M. et.al. "Service requirements for Layer 3 Provider Provisioned Virtual Private Networks" draft-ietf-ppvpn- requirements-04.txt, Work in Progress, Internet Draft, Feb 2002. [LASSERRE-VKOMPELLA-VPLS] Lasserre, M. et.al. "Virtual Private LAN Services over MPLS", draft-lasserre-vkompella-ppvpn-vpls-01.txt, Work in progress, Internet Draft, Mar 2002. [MARTINI-SIGNALING] Martini, L. et.al. "Transport of Layer 2 Frames Over MPLS", draft-martini-l2circuit-trans-mpls -08.txt, Work in Progress, Internet Draft, Nov 2001 [MOHAN-LPE] Mohan, D. et.al. "VPLS/LPE L2VPNs: Virtual Private LAN Services using Logical PE Architecture ", draft-ouldbrahim -l2vpn-lpe- 02.txt, Work in Progress, Internet Draft, Mar 2002 [MPLS-GRE] Rekhter, Y. "MPLS Label Stack Encapsulation in GRE", Rekhter et al, draft-rekhter-mpls-over-gre-03.txt, Work in Progress, Internet Draft Sep, 2001. [MPLS-IP] Worster, T. et.al. "MPLS Label Stack Encapsulation in IP", Worster et al, draft-worster-mpls-in-ip-05.txt, Work in Progress, Internet Draft, Jul 2001. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-00.txt 26.06.02 Andersson Expires Dec 2002 [Page 36 ] [PWE3-FW] Pate, P. editor, "Framework for Pseudo Wire Emulation Edge-to- Edge", Pate, P. editor, draft-ietf -pwe3-framework -00.txt, Work in Progress, Internet draft, Feb 2002 [ROSEN-L2-SIGNALING] Rosen, E. "Single-Sided Signaling for L2VPNs", draft-rosen- ppvpn-l2-signaling-01.txt, Work in Progress, Internet Draft, Feb 2002 [SAJASSI-VPLS] Sajassi, A. "VPLS Architectures", draft-sajassi-vpls- architectures-00.txt , Work in Progress, Internet Draft, Feb 2002. [SHAH-INTER] Shah, H. et.al. "IP address resolution for IP interworking of Layer 2 VPN", draft-shah-l2vpn-arp -resolve-00.txt, Work in Progress, Internet Draft, Jan 2002 [SHAH-SIG] Shah, H. et.al. "Signaling between PE and L2PE/MTU for Decoupled VPLS and Hierarchical VPLS", draft-shah -ppvpn-vpls - pe-mtu-signaling-00.txt, Work in Progress, Internet Draft, Feb 2002. 6. Acknowledgements This document is the outcome of discussions within the PPVPN Layer 2 VPN design team. The members of the design team are Eric Rosen, Cisco Systems erosen@cisco.com Hamid Ould-Brahim, Nortel Networks hbrahim@nortelnetworks.com Juha Heinanen, Song Networks jh@lohi.eng.song.fi Kireeti Kompella, Juniper Networks kireeti@juniper.net Loa Andersson, Utfors AB, loa.andersson@utfors.se Marc Lasserre, Riverstone Networks marc@riverstonenet.com Marty Borden, Atrica mborden@atrica.com Pascal Menezes, Terrabeam Pascal.Menezes@Terabeam.com Vach Kompella, Timetra Networks vkompella@timetra.com Vasile Radoaca Nortel Networks vasile@nortelnetworks.com Waldemar Augustyn, waldemar@nxp.com The team would like to thank Marco Carugi for cooperation in setting up context, working directions and taking time for discussions in this space. The team would also like to thank Tove Madsen for valuable input and reviews. INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02 Andersson Expires Dec 2002 [Page 37 ] 7. Authors Contact Loa Andersson (editor) Utfors AB P.O Box 525 SE-169 29 Solna tel: +46 8 52 70 50 38 email: loa.andersson@utfors.se INTERNET-DRAFT draft-andersson-ppvpn-l2-framework-01.txt 26.06.02